Latest and live tenders published in united arab emirates. Click on any tender to view further details.
poster printing and framing printing of 60 framed posters with white background that contains: dewa logo, dubai government logo, b lack text, colored text, images. artwork attached. dimensions of poster height: 61 cm/24 inches x width: 78.5 cm/31 inches and 5 cm paper bleed. paper type: polar matte paper frame: 1 inch boarder can be easily opened to replace worn-out posters. supplier to prov ide a sample and acquire approval before carrying out the job. for any inquiries kindly contact mr. mohamed omer 055-6080766/04-322 5944 mohamed.omer@dewa.gov.ae location: jebel ali power station complex opposite to ibn battutta mall m-station.
repair and service of make: ridgid, model: re60. replacement of ball bearing.
fabrication of prd gasket set for ztr 33kv transformers set include 03 pieces. note: prior to quote, supplier need to collect the sample. contact: mr. adel al haj 055-3088995.
internal & external coating of the booster pump of emirates road pumping station. pump details: mfr: clyde weir pump, flow rate: 526 l/sec; haed: 66 m; type: sdk 400/600; rev/min: 980 rpm. please contact mr. noor 04-3229439 for further clarifications. scope of works: specification for internal coating of pumps/ valves general these pumps & valves are used in water booster pumping stations. the fluid handled by these pumps is potable water of maximum temperature up to 50 0c. normally the water is clean but some time it is noticed to have sand and solids in stream from pipeline. these pumps are in operation since commissioning of the station . scope of work collection & transportation the contractor shall collect the pump casing through suitable pickup/crane mounted tsuitable composite materials up to original level before applying any coating. the composite material shall have the following properties: #the curried composite must be suitable for continuous immersion in the following chemicals at 21 0c 70 0f: ferric chloride, 10% hydrochloric acid, 10% sulfuric acid, 5% nitric acid, 50% sodium hydroxide and 28% ammonium hydroxide. ·#the composite shall show no blisters when exposed to de-mineralized water in an astm c 868 corrosion test at 43 0c 110 0 f for a minimum period of 6 months. #adhesion of the composite per astm d1002 shall be greater than 183 kg/cm2 2, 600 psi #the curved composite must meet or exceed t he following physical requirements: compressive strength astm d 695 914 kg/cm2 13, 000 psi. tensile strength astm d638 431 kg/ cm2 6, 136 psi flexural strength astm d 790 620 kg/cm2 8, 800 psi flexural modulus astm d 790 6.9 x 104 kg/cm2 9.87 x 105 psi. during the phases of surface preparation, application, and curing, environmental conditions will require careful monitoring a nd may require supplemental controls. critical areas of concern are relative humidity, dew point, surface temperature of the substra te, and air purity. contractor shall carryout all the procedures in a controlled environment in accordance with the latest standards and procedures. final internal coating after surface preparation and filling up the eroded surface it is required to a pply the ceramic reinforced composite materials for final coating. the composite coating materials shall have following
supply of valve; type: three way, changover valve; size: dn 40; class: 300; model:11.7, mat:1.019, fnr:723531, make: w.t.a, kks:11/12/21/22/3 1/32mbq10aa193;application:propane gas system
supply of vaultex safety gloves, nitrile coated, pn:black grey
supply of bladder;pos.2;for accumulator;accumulator type-sb-330-50-a1/112a-330a;drg no-gmd0759299;fabrication no.-4062/5/67;makehydac; appli cation - ccst#6 hydraulic oil system;e-station
supply of non-rechargeable torch light, make: streamlight, models: twin-task® 3aa led make or 2aa propolymer® xenon or equivalent
supply of acid; no standard, 0.50 mgkoh/g, in mineral oil, 500 ml, manf paragon, lot no 232-455-8, tested and cetrified in accordanc e with astm 664, fully traceable to international standards, used to determine acid number by potentiometric titration. typically used in, but not limited to, the analysis of used oils and lubricants.acid; no standard, 0.10 mgkoh/g, in mineral oil, 500 ml, manf paragon, lot no 232-455-8, tested and cetrified in accordance with astm 664, fully traceable to international standards, used to determine acid number by potentiometric titration. typically used in, but not limited to, the analysis of used oils and lubricants.
supply of bush; coupling; rubber; size 18x32dia x 28 long a/c cooling w/p sl # 8/223039 model # gh114f2 make spp uk