Filters

List of regulator-board Tenders

List of latest regulator-board Tenders in Indian Tenders. Click on any regulator-board Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for regulator-board Tenders.

All-Tenders (23)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

State Government

TRN :35763340 | 10 Nov, 2025

Tender Value : 17.65 Lacs

Dausa - Rajasthan

Tender for major repair work under state budget head at govt. sss bilona kalan -demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge: in cement mortar. dismantling stone slab roofing over wooden karries and battens (dismantling karries and battens to be paid for separately) including stacking of serviceable material and disposal of unserviceable material within 50 meter lead: demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer-in-charge. 1: 3: 6 or richer mix. dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead. providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - all work up to plinth level. m10 grade nominal mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in:cement mortar 1:6 ( 1-cement : 6-sand). centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for : columns, pillars, posts and struts etc. providing and laying in position specified grade of cement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement for beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix / design mix providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. thermo-mechanically treated bars (conforming of relevent is code) kota stone slab flooring 25 mm thick over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) for area of each slab from 2001 to 5000 sq.cm : kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete for area of each slab upto 2001 sqcm grading roof for water proofing treatment with water proffing compound cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) gola providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : plaster (ceiling): 6 mm thick cement plaster to ceiling of mix 1:3 (1cement : 3-fine sand) internal plaster : plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :12mm thick. plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :20mm thick. providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete finishing walls with acrylic smooth exterior paint of required shade including all scaffolding. new work (two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm ). distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding:new work (two or more coats) over and including scrapping and priming coat with cement primer. panting on doors & windows :- painting with synthetic enamel paint of approved brand and manufacture to give an even shade : two or more coats on new work "copping : providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc up to floor five level excluding the cost of centering and shuttering. m20 grade nominal mix 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)." wiring of light point/ fan point/ exhaust fan point/ call bell point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (is:694) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) in recessed isi marked mms ( is:9537 p - iii ) vergin material pvc conduit & it's all accessories( j.b. , bends etc.) , round tiles,18 swg hot dipped galvanized modular box with earth terminal, 6 a modular switch, modular face plate with grid plate, 3 pin ceiling rose / lamp holder/ 3 pin connector , screws etc, making connections,all as per pre approved by engineer in charge, testing etc. complete as required. for specification of copper conductor, phenolic laminated sheet's & electrical/ wiring accessories refer chapter e - 04, e - 05 & e - 07 . for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . short point (up to 3 mtr.) medium point (up to 6 mtr) long point (up to 10 mtr) wiring of 3/5 pin 6 amp. light plug point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (is:694) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) in recessed isi marked mms ( is:9537 p - iii ) vergin material pvc conduit & it's all accessories( j.b. , bends etc.) , round tiles,18 swg g.i. box with earth terminal of required size, 6 a switch, 3/5 pin 6 a socket, 3.0 mm thick isi marked phenolic laminated sheet (is : 2036 - 1995), al. alloy/ cadmium plated iron screws 20 mm cup washers etc. all as per pre approved by engineer in charge, making connections, testing etc. complete as required. for specification of copper conductor, phenolic laminated sheet's & electrical/ wiring accessories refer chapter e - 04, e - 05 & e - 07. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . on board s&f following sizes (dia.) of isi marked mms ( is:9537 p - iii ) vergin material pvc conduit as per pwd specification for electrical works along with its accessories (is: 3419 ) as required in recess including cutting the wall, covering conduit and making good the same as required. all relative and latest acceptance tests reports by any nabl accredited lab for the conduit shall be submitted before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . mms (9537 p-111)pvc condute.25mm. supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked (is:694) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a ,flame retardant as per is 10810-53, better amperage rating as per vde 0298 part 4, , in existing surface or recessed pvc/ ms conduit/casing capping including all as per pre approved by engineer in charge,making connections, etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . 2 x1.5 sqmm supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked (is:694) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a ,flame retardant as per is 10810-53, better amperage rating as per vde 0298 part 4, , in existing surface or recessed pvc/ ms conduit/casing capping including all as per pre approved by engineer in charge,making connections, etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . 2 x2.5 sqmm providing & fixing of 240/415 v ac mcb with positive isolation of breaking capacity not less than 10 ka (b/ c tripping characteristic as per type of load and site requirement) 4kv impulse withstand voltage, as per pwd specification for electrical works with isi marked is 8828(1996) / conforming to iec 60898-1 2002, iec 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , ip 20 contact protection and fitted with existing distribution board/sheets, min. operation 20,000 upto 32 a rating and 10,000 upto 63 a, 5000 for 80 a rating including making connections, testing etc. as required. . oem shall have submit nabl / cpri / erda accrediated lab test reports before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr .6a to 32a rating. 50 a to 63a rating providing & fixing of ip20 smd mid power led batten type integrated light fixture made from polycarbonate /extruded aluminium powder coated housing with in built driver , power consumption of 18w/20w ,system lumen efficacy = 120 lm/watt output, internal surge protection of 2.5 kv with short & open circuit protection ,thd < 10% ,p.f.=0.95, cri >80 , life time of minimum 50000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing. 1170mm(+/-10%) led batten with min. lumen output 2200 lm providing & fixing of energy efficient /energy saving ip 20 led direct retrofit bulb in existing holder or fixture as required with system lumen efficacy =100 lm/watt output ,pf 0.95 , cri >70, minimum life time of minimum 25000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . for additional technical parameters of product/ work, refer annexure "a" attacheded with this bsr.6/7 watt providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed un-arrmoured aluminium cable confirming to is:1554 p-i / is :7098 p - i of 1.1 kv with h4- grade electrolytic aluminium conductor confirming to is 8130 of purity >99.6 %, inner / outer sheath confirming to is:5831 in existing rcc / hume / stoneware / pvc pipe/ open duct/cable trench / cable tray (with cable tie) including testing etc. as required of following size. oem must have it's own in house nabl accrediated laboratory for testing procedure as per is:10810. for additional technical parameters of product / work refer annexure 'a' attached with this bsr 6.0 sq. mm 4 core providing & fixing of bee star rated copper wounded double ball bearing capacitor start, aluminium body & metallic blade ceiling fan conforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing (i.e. isi marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . providing & fixing of isi marked (is:1258) batten/angle lamp holder with cm/l no. printed and made out from industrial grade polycarbonate or fire resistant abs material, brass terminal & captive screwsincluding making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . p & f 1.2mm thick m.s. recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side . all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure 'a' attached with this bsr providing & fixing of 240/415 v isolator as per pwd specification for electrical works with isi marked is:13947-iii/conforming to iec 60947-3, suitable for ac22a utilization catagory, 4kv impulse withstand voltage, true contact indication, red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting, minimum phase termination capacity of 35sq.mm. , label holding facility , ip 20 contact protection and fitted with existing distribution board / sheet including making connections, testing etc. as required. oem shall have submit nabl / cpri / erda accrediated lab test reports before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . 30/40 amp rating . providing & fixing of modular type 120 w step fan regulator duly isi marked (is 11037:1984 ) with cm/l no. printed made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with ip-20 rating , including all as per pre approved by engineer in charge,making connections, testing etc. as required. for additional technical parameters of product / work refer annexure 'a' attached with this bsr5 step fan regulator 2 module 360 dgree rotating p & f isi marked (is:3854) 6 amp. flush type non modular switch with cm/l no. printed and made out from industrial grade polycarbonate or fire resistant abs material including cutting hole in tile and making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . providing & fixing of of 3/5 pin 6 amp. flush type non modular socket made out from industrial grade polycarbonate or fire resistant abs material, brass terminal with porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr .

State Government

TRN :35765746 | 10 Nov, 2025

Tender Value : 4.90 Lacs

Jaipur - Rajasthan

Tender for demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge: in cement mortar. dismantling stone slab roofing over wooden karries and battens (dismantling karries and battens to be paid for separately) including stacking of serviceable material and disposal of unserviceable material within 50 meter lead: demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer-in-charge. 1: 3: 6 or richer mix. dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead. earth work in excavation by mechanical means (hydraulic excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. all kinds of soils providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - all work up to plinth level. 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - all work up to plinth level. m10 grade nominal mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). supply & stacking good soil of earth at site complete including loading unloading & transportation etc.good soil of earth filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift. random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in:cement mortar 1:6 ( 1-cement : 6-sand). centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for :columns, pillars, posts and struts etc. centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for : columns, pillars, posts and struts etc. providing and laying in position specified grade of cement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement for beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix / design mix providing and laying in position specified grade of cement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcement for walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.m20 grade nominal mix / design mix roviding m-25 grade concrete by using cement as per codal provision instead of m-20 grade design mix. providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. thermo-mechanically treated bars (conforming of relevent is code) kota stone slab flooring 25 mm thick over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) for area of each slab from 2001 to 5000 sq.cm : kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete for area of each slab upto 2001 sqcm grading roof for water proofing treatment with water proffing compound cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) gola providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :20mm thick. finishing walls with acrylic smooth exterior paint of required shade including all scaffolding. new work (two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm ). distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding:new work (two or more coats) over and including scrapping and priming coat with cement primer. "copping : providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc up to floor five level excluding the cost of centering and shuttering. m20 grade nominal mix 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)." wiring of light point/ fan point/ exhaust fan point/ call bell point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (is:694) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) in recessed isi marked mms ( is:9537 p - iii ) vergin material pvc conduit & it's all accessories( j.b. , bends etc.) , round tiles,18 swg hot dipped galvanized modular box with earth terminal, 6 a modular switch, modular face plate with grid plate, 3 pin ceiling rose / lamp holder/ 3 pin connector , screws etc, making connections,all as per pre approved by engineer in charge, testing etc. complete as required. for specification of copper conductor, phenolic laminated sheet's & electrical/ wiring accessories refer chapter e - 04, e - 05 & e - 07 . for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . short point (up to 3 mtr.) medium point (up to 6 mtr) long point (up to 10 mtr) wiring of 3/5 pin 6 amp. light plug point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (is:694) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) in recessed isi marked mms ( is:9537 p - iii ) vergin material pvc conduit & it's all accessories( j.b. , bends etc.) , round tiles,18 swg g.i. box with earth terminal of required size, 6 a switch, 3/5 pin 6 a socket, 3.0 mm thick isi marked phenolic laminated sheet (is : 2036 - 1995), al. alloy/ cadmium plated iron screws 20 mm cup washers etc. all as per pre approved by engineer in charge, making connections, testing etc. complete as required. for specification of copper conductor, phenolic laminated sheet's & electrical/ wiring accessories refer chapter e - 04, e - 05 & e - 07. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . on board s&f following sizes (dia.) of isi marked mms ( is:9537 p - iii ) vergin material pvc conduit as per pwd specification for electrical works along with its accessories (is: 3419 ) as required in recess including cutting the wall, covering conduit and making good the same as required. all relative and latest acceptance tests reports by any nabl accredited lab for the conduit shall be submitted before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . mms (9537 p-111)pvc condute.25mm. supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked (is:694) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a ,flame retardant as per is 10810-53, better amperage rating as per vde 0298 part 4, , in existing surface or recessed pvc/ ms conduit/casing capping including all as per pre approved by engineer in charge,making connections, etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . 2 x1.5 sqmm supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked (is:694) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a ,flame retardant as per is 10810-53, better amperage rating as per vde 0298 part 4, , in existing surface or recessed pvc/ ms conduit/casing capping including all as per pre approved by engineer in charge,making connections, etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . 2 x2.5 sqmm providing & fixing of ip20 smd mid power led batten type integrated light fixture made from polycarbonate /extruded aluminium powder coated housing with in built driver , power consumption of 18w/20w ,system lumen efficacy = 120 lm/watt output, internal surge protection of 2.5 kv with short & open circuit protection ,thd < 10% ,p.f.=0.95, cri >80 , life time of minimum 50000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing. 1170mm(+/-10%) led batten with min. lumen output 2200 lm providing & fixing of energy efficient /energy saving ip 20 led direct retrofit bulb in existing holder or fixture as required with system lumen efficacy =100 lm/watt output ,pf 0.95 , cri >70, minimum life time of minimum 25000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . for additional technical parameters of product/ work, refer annexure "a" attacheded with this bsr.6/7 watt providing & fixing of bee star rated copper wounded double ball bearing capacitor start, aluminium body & metallic blade ceiling fan conforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing (i.e. isi marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . providing & fixing of isi marked (is:1258) batten/angle lamp holder with cm/l no. printed and made out from industrial grade polycarbonate or fire resistant abs material, brass terminal & captive screwsincluding making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . p & f 1.2mm thick m.s. recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side . all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure 'a' attached with this bsr providing & fixing of 240/415 v isolator as per pwd specification for electrical works with isi marked is:13947-iii/conforming to iec 60947-3, suitable for ac22a utilization catagory, 4kv impulse withstand voltage, true contact indication, red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting, minimum phase termination capacity of 35sq.mm. , label holding facility , ip 20 contact protection and fitted with existing distribution board / sheet including making connections, testing etc. as required. oem shall have submit nabl / cpri / erda accrediated lab test reports before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . 30/40 amp rating . providing & fixing of modular type 120 w step fan regulator duly isi marked (is 11037:1984 ) with cm/l no. printed made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with ip-20 rating , including all as per pre approved by engineer in charge,making connections, testing etc. as required. for additional technical parameters of product / work refer annexure 'a' attached with this bsr5 step fan regulator 2 module 360 dgree rotating

State Government

TRN :35766126 | 10 Nov, 2025

Tender Value : 4.90 Lacs

Dausa - Rajasthan

Tender for demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge: in cement mortar. dismantling stone slab roofing over wooden karries and battens (dismantling karries and battens to be paid for separately) including stacking of serviceable material and disposal of unserviceable material within 50 meter lead: demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer-in-charge. 1: 3: 6 or richer mix. random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in:cement mortar 1:6 ( 1-cement : 6-sand). centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for : columns, pillars, posts and struts etc. providing and laying in position specified grade of cement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement for beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix / design mix providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. thermo-mechanically treated bars (conforming of relevent is code) grading roof for water proofing treatment with water proffing compound cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) gola providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :20mm thick. finishing walls with acrylic smooth exterior paint of required shade including all scaffolding. new work (two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm ). distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding:new work (two or more coats) over and including scrapping and priming coat with cement primer. "copping : providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc up to floor five level excluding the cost of centering and shuttering. m20 grade nominal mix 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)." wiring of light point/ fan point/ exhaust fan point/ call bell point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (is:694) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) in recessed isi marked mms ( is:9537 p - iii ) vergin material pvc conduit & it's all accessories( j.b. , bends etc.) , round tiles,18 swg hot dipped galvanized modular box with earth terminal, 6 a modular switch, modular face plate with grid plate, 3 pin ceiling rose / lamp holder/ 3 pin connector , screws etc, making connections,all as per pre approved by engineer in charge, testing etc. complete as required. for specification of copper conductor, phenolic laminated sheet's & electrical/ wiring accessories refer chapter e - 04, e - 05 & e - 07 . for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . short point (up to 3 mtr.) medium point (up to 6 mtr) long point (up to 10 mtr) wiring of 3/5 pin 6 amp. light plug point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (is:694) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) in recessed isi marked mms ( is:9537 p - iii ) vergin material pvc conduit & it's all accessories( j.b. , bends etc.) , round tiles,18 swg g.i. box with earth terminal of required size, 6 a switch, 3/5 pin 6 a socket, 3.0 mm thick isi marked phenolic laminated sheet (is : 2036 - 1995), al. alloy/ cadmium plated iron screws 20 mm cup washers etc. all as per pre approved by engineer in charge, making connections, testing etc. complete as required. for specification of copper conductor, phenolic laminated sheet's & electrical/ wiring accessories refer chapter e - 04, e - 05 & e - 07. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . on board s&f following sizes (dia.) of isi marked mms ( is:9537 p - iii ) vergin material pvc conduit as per pwd specification for electrical works along with its accessories (is: 3419 ) as required in recess including cutting the wall, covering conduit and making good the same as required. all relative and latest acceptance tests reports by any nabl accredited lab for the conduit shall be submitted before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . mms (9537 p-111)pvc condute.25mm. supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked (is:694) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a ,flame retardant as per is 10810-53, better amperage rating as per vde 0298 part 4, , in existing surface or recessed pvc/ ms conduit/casing capping including all as per pre approved by engineer in charge,making connections, etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . 2 x1.5 sqmm supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked (is:694) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a ,flame retardant as per is 10810-53, better amperage rating as per vde 0298 part 4, , in existing surface or recessed pvc/ ms conduit/casing capping including all as per pre approved by engineer in charge,making connections, etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . 2 x2.5 sqmm providing & fixing of ip20 smd mid power led batten type integrated light fixture made from polycarbonate /extruded aluminium powder coated housing with in built driver , power consumption of 18w/20w ,system lumen efficacy = 120 lm/watt output, internal surge protection of 2.5 kv with short & open circuit protection ,thd < 10% ,p.f.=0.95, cri >80 , life time of minimum 50000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing. 1170mm(+/-10%) led batten with min. lumen output 2200 lm providing & fixing of energy efficient /energy saving ip 20 led direct retrofit bulb in existing holder or fixture as required with system lumen efficacy =100 lm/watt output ,pf 0.95 , cri >70, minimum life time of minimum 25000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . for additional technical parameters of product/ work, refer annexure "a" attacheded with this bsr.6/7 watt providing & fixing of bee star rated copper wounded double ball bearing capacitor start, aluminium body & metallic blade ceiling fan conforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing (i.e. isi marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . p & f 1.2mm thick m.s. recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side . all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure 'a' attached with this bsr providing & fixing of 240/415 v isolator as per pwd specification for electrical works with isi marked is:13947-iii/conforming to iec 60947-3, suitable for ac22a utilization catagory, 4kv impulse withstand voltage, true contact indication, red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting, minimum phase termination capacity of 35sq.mm. , label holding facility , ip 20 contact protection and fitted with existing distribution board / sheet including making connections, testing etc. as required. oem shall have submit nabl / cpri / erda accrediated lab test reports before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . 30/40 amp rating . providing & fixing of modular type 120 w step fan regulator duly isi marked (is 11037:1984 ) with cm/l no. printed made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with ip-20 rating , including all as per pre approved by engineer in charge,making connections, testing etc. as required. for additional technical parameters of product / work refer annexure 'a' attached with this bsr5 step fan regulator 2 module 360 dgree rotating

Central Government/Public Sector

TRN :35749619 | 10 Nov, 2025

Tender Value : 0

Panchkula - Haryana

Tender for gem bids for sheet bakelite , tape pvc , sheet bake , bell indication 12 way , pvc gang box , batten nails , pvc flexible , shadals various , telephone nails , plastic rawal plug , bulb 100 , false ceiling , bell cord less , bell indication , bus bar , electronic meter , fan hook , plug top 15 amp , pvc 200mm , pvc 250mm , pvc 300mm , pvc bulb holder angular type , pvc gang box 15 amp , hexa blade double ended , holder bipin rotraty , insulation tape , switch neon indicator , plywood mdf board 8x4x18mm , plywood , glass shelf , low level , pvc pipe 75mm , sink coupling 100mm , cp peg set of 06 , cp hand shower , curtain rod , pvc pipe 100mm , glass sheet frosted , waste pipe , door stopper , waste coupling , cp brass soap dish , handle aluminum 150mm , tower bolt ms 100 mm , bracket sider end doom , glass sheet clear , tower bolt , cp brass , bracket for fancy , mortice lock , aluminum hinges 100 mm , door seal 900mm long , grating cp , door seal 1200 mm long , thread for plumber , ms hinges 100mm , helical door spring , grating cp stainles , nipple hexa 15 mm , hamber drill bit , rawal plug , blade cutter iron , paper holder , m seal , washer for cistern , fevicol , ss handle , wire mesh , magnetic catcher , dr fixit , tarpentine oil , pvc ball , drip seal , angular stop cock , ms hasp and stapple , drain cover mm , drain cover , taflon tape , star bit for drill , glass shelf 600mm long , 15mm kitec elbow , 15mm kitec socket , 15mm kitec tee , 15mm kitec union , kitec connectore , electric insulation rubber mat , street light 120w , street light 90w , spot light green , spot light warm white , spot light cool white 12w , contractor 185 amp 415 v , contractor 40 amp 415 v , led recess , cable pvc 16 sqmm 1 core , cable pvc 2 point 5 sqmm 1core , cable pvc 1 point 5 sqmm 3 core , cable pvc 1 point 5 sqmm 1core , led lamp 12 watt , led lamp 9 watt , led recessed luminaire 12 watt , led surface celing , cable pvc flat , led spot light 12 , automatic star , dol starter , calling bell ding dong , insualtion tape , aluminium thimble 150 , aluminium thimble 400 , plug top 3 pin16 amp , modular fan regulator , switch board boxes 6 modular , aluminium inline , aluminium thimble , switch board boxes , cable jointing kit , aluminium inline connector 185 , modular bell push , aluminium inline connector 95 , aluminium inline connector , aluminuum thimble 95 , aluminium thimble 50 , aluminuum thimble 70 , pvc gang , aluminium thimble 35 sqmm , aluminium thimble 25 , insulation tape , batten holder 6 amp , connector 35 sqmm , inline connector , aluminium connector , junction box , bulb 100 w , industrial socket , aluminium inline 50 , pvc condute pipe 20 mm , pvc condute clamp , modular plate 3 module , modular plate 4 module , modular plate 6 module , hydraulic door closer , glass sheet , stainless steel curtain rod , glass sheet clear , copper sulphate , frame plate 6 module , aluminium door seal , nrv 150 mm , patchmat bitumen , cp brass extension nipple , hack saw blade double edge , brass nozzle 15 mm for fountain , frame plate 3 module , nrv 100 mm , hex nipple 20 mm x 50 mm , ht tape black roll of 20 mtr , brass spindle , particle board , brass nozzle , ms but hinge 100 mm , ball valve brass , hex nipple , bearing grease , magnetic door catcher , cp brass urinal , cp wall bracket l shape , insulated tape , cp end bracket , blanking plate , lime , industrial socket 63 amp , floor door closer , aluminim hasp and staple , wire clamp 10 mm , batten nail , pvc internal cistern10 ltr capacity , tank 1000 ltr , ss curtain rod , sliding bolt , cotton thread 1 pkt 60 pcs , aluminium sheet 1 mm thick , toilet seat covers (v2) (q4) , ptmt tap fitting (q3) , modular piano type domestic electrical switches as per is 3854 (q3) , piano type non modular domestic electrical sockets - is 1293 (q3) , non - modular piano type domestic electrical switches as per is 3854 (q3) , piano type modular domestic fan regulator as per is 11037 (q3)

Central Government/Public Sector

TRN :35752852 | 10 Nov, 2025

Tender Value : 0

Lucknow - Uttar Pradesh

Tender for gem bids for led luminaire recessed luminaire v3 conforming to is10322 part 5/section 2 q3, plug and socket distributionboard q3, electrical plugs v2 isi marked to is 1293 q2, mcb - miniature circuit - breakers for a.c. operation as peris / iec 60898 part 1 q2, miniature circuit breakersdistribution boards as per is 13032 q3, casing cappingpvc 25x20 mm, heating element 2000w triangular type, heating element 1500w, lamp holder angular metal ring, led emergency lamp 12 watt, led emergency lamp 9 watt, cp brass health faucet 15 mm with 1.5 mtr long 304 gradehose and hook, cable pvc copper sc 6 sqmm, angle valvecp brass 15 mm, hydraulic door closer aluminium body, decorative wall light fitting with acrylic cover inpolycarbonate base suitable for 9 watt led lamp, ac boxmodular type pvc body with mcb sp 25 a, cable pvc almntwo core 2.5 sqmm, isolator 63a 4 pole, cable flatsumerceble sheathed 3 core 6 sqmm, cable pvc almn sc10 sqmm, cable pvc almn tc 4 sqmm, cable pvc almntc 6 sqmm, isolator 100a 4 pole, isolator 100a tp, cablepvc copper sc 10 sqmm, switch socket comb piano type 6oblique 5 amp 5 pin, street light 30 watt, gate valvebrass 15 mm, regulator electronic type for ceiling fan, regulator socket type, regulator modular 2 module sockettype, pillar tap cp brass 15 mm, plywood commercial bwr7 feet x 3 feet x 12 mm, sunmica 1 mm thick 8 feet x4feet, plywood commercial 8 feet x 4 feet x 19 mm bwr, prelaminated edhmr or hdmr board 8 feet x 4 feet x 25 mm, heat shrinkable 120 sqmm 3 core joint kit, heat shrinkable185 sqmm 3 core joint kit, heat shrinkable 95 sqmm 3 corejoint kit /bid number: gem/2025/b/6795733* /dated: 30-10-2025 & & / bid document1 / 41

Central Government/Public Sector

TRN :35753319 | 19 Nov, 2025

Tender Value : 13.78 Lacs

Mundra - Gujarat

Tender for gem bids for supply and installation of double arm pole , supply and installation of single arm pole , supply and installation of led street lights , supply and installation of garden bollard type pole and 15w led lantern , supply and installation of 100w colour flood light , supply and installation of 50w flood light , supply and installation of 1.5 sq.mm x 3c armoured cable , supply and installation of electrical pole junction box , supply and installation of 30a, 6 way close type connector , supply and installation of 6a, 240v single pole mcb , supply and fabrication of copper clamp by using 25x3mm copper strip , supply and installation of 1. 5sq.mmx3c pvc insulated and sheathed coper flexible cable , supply and installation of 25 mm pvc pipe , supply and installation of 10a, 2p, mcb in power house , supply and installation of 6 way mcb distribution board , supply and installation of 25mm steel wire reinforced pvc flexible pipe , supply and laying of 50mm upvc pipe for road crossing , supply and installation of miscellaneous items , labour charges for excavation of cable trench , excavation for pole foundation , construction of footing structure , applying cement primer , applying signal red paint , applying metal primer , applying aluminium paint , demolishing of existing 29 footing structure , labour charges for laying of pipes in road crossings and ug cable markings with red colour bricks , supply and installation of 2m modular switch board box with matching frame plate and cover plate , supply and installation of 3m modular switch board box with matching frame plate and cover plate , supply and installation of 4m modular switch board box with matching frame plate and cover plate , supply and installation of 6m modular switch board box with matching frame plate and cover plate , supply and installation of 8m modular switch board box with matching frame plate and cover plate , supplying and fixing 6a modular switch and socket on the existing modular plate and switch box including connections , supplying and fixing 3 pin 6a modular socket outlet, on the existing modular plate and switch box including connections , supplying and fixing 16a modular switch on the existing modular plate and switch box including connections , supplying and fixing 6 pin 16 modular socket on the existing modular plate and switch box including connections , supply and installation of 16a universal extension board , supply and installation of 1m modular electronics fan regulator , supply and installation of 4 way spn db with earth connection. , supply and fixing 6a mcb , supply of 300mm pvc dom exhaust fan for installation in power house in the existing opening , installation of 300mm exhaust fan , extra carpentry work including supply and fixation of 19mm plywood on the exiting and ss net fixation at the outer side of opening , supply and installation of 12w, round surface led light , supply and fixing modular angle holder , supply and installation of self ballasted 20w led lamp , supply of 1200mm ceiling fan , installation testing and commissioning of ceiling fan , supply and installation of rotational adjustable pvc street light wall mount stand , supply and installation of led street light 25w,230v,50hz ac inbuilt with surge protection circuit , supply and installation of single phase 230v ac, 2hp monoblock pump , supply and installation of single phase 230v ac, 2hp motor starter , supply and installation of 6.5kg or higher front load, fully automatic washing machine , supply and installation of washing machine trolly stand , supply and installation of good quality of gate light on main gate pillar , supply of domestic clothing iron , supply of good quality nylon flexible pipe for gardening purpose , long solar panel cleaning brush kit heavy duty , gi mounting arm with clamps for installation led street light , supply of pvc suction hose and other items as per atc clause 7.1

State Government

TRN :35722522 | 18 Nov, 2025

Tender Value : 0

Shahdol - Madhya Pradesh

Tender for gem bids for r410 gas, r 32 gas, r 22 gas, lpg gas, lpg, lpg flame, shampoo, copper tube, cotton waste, clamp meter, nitrogen pressure gas, refrigeration oil, capacitor, relay, control board, polyurethine foam, abs plastic, sheetalluminium, copper wire for wiring, silicon chipscapacitor, chalk, duster, photocopy paper, file cover, paper pin steel, nirma powder, modular plate, modularplate, modular switch, modular switch, modular socket, ceiling rose, angle holder, modular dummy, round plate, insulation tape, packing tape, condensor, sleeve, winding sheet, thread for winding, tarpin oil, grease, giwire, soldering wire, pvc clip, led bulb, straight holder, plug top, electrical wiring board, mcb box, single doormcb distribution box, mcb, insulator, modular board, modulate switch, fan regulator, led, copper wire, powerswitch, power socket, diode 4007, transistor, igbt, ujt, resistance, mosfet, pcb plate, soldering iron, desoldering pump, solder wire, solder paste or flux, general purpose pcb blanks, copper clad board, conecting wires, carbon film resistors various wattageand resistance values, capacitors different types ceramic, electrolytic, tantalum and voltage capacitance values, diodes general purpose, rectifiers, zener diodes, amplifieric, digital ic ex-nor gate, single phase center tappedstepdown transformer, spst switch, single way switch, two way switch, audio video cable, bnc connector, kitkat fuse, mcb fuse, rj45 connector, sata connector, scr, diac, triac, microcontrollers, battery, regulated ics, timer ic, ic base, dry cells, led bulbs, neon tester, ldr, opto coupler ic, logic gates ic, fip flop ic, counteric, decoder ic, op amp ic, function generator ic, fmtransmitter ic, receiver ic, piezo buzzer, frequencymultiplier ic, digital ics, optical fibre cable, ms flate, msround bar, power hexa blade, cutting tool, ms block, msgear blank piece, ms gear blank piecce, ms gear blankpiece, ms bar, ms sheet, ms filler rod

Central Government/Public Sector

TRN :35723825 | 07 Nov, 2025

Tender Value : 0

Chandigarh Ut - Chandigarh

Tender for gem bids for led luminaire for road and street lights v2 conformingto is 10322 part 5 section 3 q3 led garden light v2q2 led batten q2 xlpe cable for working voltages upto and including 11 kv as per is 7098 part 1 q2 ledtube light retrofit type q2 led luminaire forfloodlight v2 conforming to is 10322 part 5section 5q3 led bulkhead light q3 self ballasted led lampsfor general lighting services v2 conforming to is 16102q2 molded case circuit breakers mccb as per is iec60947 q3 mcb - miniature circuit - breakers for acoperation as per is iec 60898 part 1 q2 piano typemodular domestic fan regulator as per is 11037 q3 piano type modular domestic electrical sockets - is 1293q3 pvc copper cable single core and multi core circularsheathed cord with flexible conductor v2 as per is 694q2 modular piano type domestic electrical switches asper is 3854 q3 elecric bells and accessories as per is2268 q3 mcb disturbuisation box tp 12 way ledinverator batten 25 watt led inverator batten 30 watt pvc copper cable flexible 6 sq mm single core led streetlight 90 watt inverter di mmable ir sensor pvc coppercable flexiable 2 point 5 sq mm x 3 core led ceiling fitting2 inch x 2 inch recess mounting 36 watt pvc copper cableflexiable single core 10 sq mm aluminum cable pvcinsulated twin core 16 sq mm pvc copper cable flexiablesingle core 4 sq mm sluice valve pn 1 point 6 size 250 mm cable pvc flexible copper conductor 2 point 5 sqmm singlecore nrv 150 mm cable flat aluminum conductor 2 core10 sq mm gun metal gate valves size 15 mm ledfountain light coloured 6 watt pvc connection pipe 15 x450 mm long with brass heating element for geyser 2000watt mcb tpn 32 amp b curve pvc connection pipe 15 x600 mm bleaching powder heating element for geyser bid number gem2025b6810121 dated 28-10-2025 bid document1 121 1 1 1500 watt, mcb distribuation box 8 way, sluice valve pn 1point 6 size 100 mm, modular socket 20 amp, ball valve 40mm brass, switch change over switch 4 pole 100 amp, ballvalve 50 mm brasss, high strengh calcium based chlorinegranules chorination chemical 25 kg bags, sluice valve pn1 point 6 size 150 mm, ball valve 25 mm brass, pvc tape20 mm x 25 mtr a, led inverter street light 60 watt, isolator 63 amp tpn, gun metal gate valves size 20 mm, multicore wire pvc copper of size 2 point 5 sq mm, ballvalve 63 mm brass, ball valve brass of size 20 mm, frameplate 6 module, modular socket 6 amp, modular fanregulator switch type, condenser 2 point 5 mfd, gi union50 mm, sluice valve pn 1 point 6 size 80 mm, isolater 63amp with encloser, rccb 2 pole 63 amp 300 ma, pvc flatcable aluminum 6 sqmm twin core 100 mtr, mcb spn 40amp b curve, switch board boxes 6 modular, thimblecopper of size 150 sqmm, isolator 40 amp tp, modularswitch 20 amp one way, switch 6 amp one way, gi union40 mm, fan pvc ventilator 10 inch sweep, gi nipple 40 x150 mm long, gi socket 50 mm, capacitor 3 point mfd, pvc gang box 6 amp, gi tee 50 mm, gi nipple mediumgrade 40 mm dia, frame plate 8 module, frame plate 3module, thermostat switch for geyser, gi tee 40 mm, gielbow 50 mm, gi socket 80 mm, capacitor 4.0 mfd, ceilling rose, gun metal gate valves size 25 mm, gi nipplemedium grade 50 mm dia x 150 mm, gi elbow 80 mm, frame plate with matching cover plate 2 modular, plugmetal clad 20 amp, frame plate 4 module, gi elbow 40 mm, gi nipple 40 x 100 mm, gi elbow 20 mm, gi socket 40mm, gi nipple 40 x 50 mm long, bulb 100 wattincandesent, pvc gang box 5 amp, gi elbow 25 mm, blanking plate, thimble aluminium size 35 sqmm pack of50, thimble aluminium size 70 sqmm pack of 50, thimblealuminium size 95 sqmm pack of 50, thimble aluminiumsize 120 sqmm pack of 50, thimble aluminium size 185sqmm pack of 50, gi plug 15 mm, gi plug 20 mm, gi plug25 mm, gi plug 40 mm, gi plug 50 mm //bid details2 / 121

Central Government/Public Sector

TRN :35725458 | 18 Nov, 2025

Tender Value : 0

Pune - Maharashtra

Tender for gem bids for 10304419 lv6 mt6 2525 2030 5816 rubber hose waterpump to t connector 10602534 lv7 fat6x6 ee lv8519596 packing 10602539 lv7 fat6x6 ee lv8 512508packing set packing set extn cyl 10586823 lv7hmv6x6 mbrl l t f3569510 wheel nut m 22x2 5 10316208 lv7 ld b 4458603 s a of hose waterseparator fuel filter 10320889 lv7 ld b 8780511hose assy air comp drain to crankcase 10362846lv7 mpvy 640 03 1613 1 inclined pipe 10325720 lv7mpvy 015 l052 00 rocker switch 10363221 lv7 mpvy115 43 0058 1 main harness dash board 10353809lv7 mpvy f 8501010 pipe assy powder coated 10313782 lv7 mpvy b8312165 s a of hose 4 way 1 outto front parking 10362866 lv7 mpvy 765 50 2783 84cap 10363043 lv7 mpvy 115 43 0032 1 engine harness 10362545 lv7 mpvy 640 03 1612 1 intermediate pipe 10362681 lv7 mpvy 640 03 1611 1 bend pipe 10609485lv7 mpvy 101 107 expansion valve 10318097 lv7mpvy 007 0029 00 pcb gl w153 24v 10363208 lv7 mpvy115 43 0057 1 indoor light and fan harness 10325837 lv7 mpvy 012 l006 00 stop valve 5 8 10324783 lv7 mpvy f 8500910 pipe assy powdercoated 10611570 lv7 sac10x10 wc al p 5104921 sealkit ext 2 cylinder 10611569 lv7 sac10x10 wc al p5104920 seal kit ext 1 cylinder 10611656 lv7sac10x10 wc al p 5104925 seal kit tandem pump 10609483 lv7 sac10x10 wc al p0f00042 sensorpressure 10611571 lv7 sac10x10 wc al p 5104922seal kit hor outrigger cylinder 10611607 lv7sac10x10 wc al pk100004 thermostat aitf 50 24v 10611567 lv7 sac10x10 wc al p 5104918 seal kitcolumn cylinder 10611568 lv7 sac10x10 wc al p5104919 seal kit boom cylinder 10609496 lv7 bid number gem2025b6831514 dated 28-10-2025 bid document1 147 sac10x10 wc al ppt00001 sump oil pan gasket 10611572 lv7 sac10x10 wc al p 5104923 seal kitvertical outrigger cylinder 10347395 lv7 stlnf8047100 tail light 10301530 lv7 awo 1301aa0501ninstrument cluster lbpv 10302578 lv7 awo 5340180691 069095 grommet transfer shift lever lbpv 10527001 43 i 43 akl b6518506 cap female for 38 mmhose 10517795 43 i 43 akl b6518525 delivery pipewith hose 10517805 43 i 43 akl b6518515 pump assy 10517889 43 i 43 akl b6518558 water level indicatorassy 10547417 k7 4720 000180 hose rubber 19 mm x 15 mtrs long 10536954 k7 4720 000185 hose rubber100 mm x 3 mtr long 10385384 k7 ikg 0274 pipe hosew o coupling 70mm for 2 1 2 10382561 k7 p 2600642ball valve ss ic 76 2 mm 10386731 k7 f 1500132impeller for tff large mk v mtd on al 10382035 k74210720259466 icn 4210002957 hose non metalic cpldelivery w o 10311363 lv7 itr beml 6220 000161 taillight stop light lh sb 122 bn 10319141 lv7 itr beml50 331 knob lot 3 4 10316124 lv7 itr beml 50 66 41hex nut m16 lot 1 10317455 lv7 itr beml 50 57 4 hexscrew m 6 x 20 lot 2 3 10311345 lv7 itr beml 5920000113 fuse electrical 5 amps 10325521 lv7 itr beml3120 000377 bushing sleeve steel ht od 58 x id 50 10322584 lv7 itr beml 5315 003175 pin toggle eyecollar lot 2 to 4 10318832 lv7 itr beml 50 319 128hex nut m 10 lot 2 to 4 10320743 lv7 itr beml 50 414washer flat steel ms od 70 x id 39 x 6 10321526 lv7itr beml 3020 000435 pulley groove 10322305 lv7itr beml 50 629 103 pipe l 900x5 8 od x16 g seamlessms tube 10323044 lv7 itr beml 50 641 cap assy lot 2to 4 10311515 lv7 itr beml 6220 000158 lightconvoy cross 10 8o n 10313491 lv7 itr beml rtto404400 extension bar 20 len 400mm to is7991 10314227 lv7 itr beml 50 389 2 cover lot 3 4 10314329 lv7 itr beml 5365 008416 50 214 1 shim 2 mmthk shim for thrust pad 2mm 10317621 lv7 itr beml50 424 bituminous felt washer lot 2 to 4 10317854lv7 itr beml 50 481 nut assy 10317931 lv7 itr beml50 38 7 washer od130 id50 thk 10 lot 1 10318974 lv7itr beml 5306 057300 bolt machine 10322538 lv7 itrbeml 5315 003208 pin straight headed lot 2 10323079 lv7 itr beml 50 66 75 d shackle lot 2 10321818 lv7 itr beml 5310 006455 nut lock hex rhthreads precision steel 10558600 w17 8705458 hdsocket 41mm 19mm sq drive 10373399 w17 iws vs7852135 00 lub oil filter 10350299 w17 mh 02367750hose 10350496 w17 mh 02050550 shoe and liningassy 10369850 w17 mh 39550621 hose sump to pump 10558622 w17 2023466 dummy shaft 10371990 w17 mh02354659 filter return 10351119 w17 iws gbm59076399 exhaust pipe engine end 10558684 w17 iwsace coq03210200w wheel cylinder kit 10351232 w17mh 39550630 hose tee piston rod to lh rh tilt cyl 10369847 w17 mh 39550629 hose lift rod end to lhrh tilt cyl 10350558 w17 mh 02012102 trans oilfilter 10369848 w17 mh 39550625 hose steering unitto cyl 10351107 w17 iws gbm 39400087 seal kit liftcyl repairs dantal 10350554 w17 mh 02006899moulded hose radiator top 10371411 w17 iws vs785775304 battery cable ve 10333087 lv7 av 15 324914 030 558 small sphere 38 100 400 dvc 500016 222 10344972 lv7 av 15 485 sd 91087 hose 722 16 1515 650 10339074 lv7 av 15 616 811 000 000 paint brush bid details2 147 1 1 10329027 lv7 av 15 578 003 003 252 64 compensatingwasher, 10334660 lv7 av 15 578 003 009 152 16packing, 10312782 lv7 t 815 993 300 089 0 o ring, 10333514 lv7 t 815 5307 004463 stud c m8x65 is 18621975 8 8, 10337230 lv7 t 815 5315 009535 split pin4x36 is 549 74, 10334126 lv7 t 815 107 214 115 120washer spring tension 107 214 115 120, 10334539lv7 t 815 106 231 140 411 screw self drilling 106 231140 411, 10336075 lv7 t 815 130 050 510 584 springhelical compression, 10337362 lv7 t 815 442 950 470024 ball socket, 10315746 lv7 t 815 4x4 442 054 430044 knob, 10531998 lv7 t 815 hmv 442 076 827 844line, 10530973 lv7 t 815 hmv 442 052 780 244 nut, 10515785 lv7 t 815 hmv 319 110 543 000 coupling 13csn 137881 22, 10532040 lv7 t 815 hmv 442 076 835804 line, 10531846 lv7 t 815 hmv 442 076 856 524 lineto inflation boosting, 10518288 lv7 t 815 hmv 442976 960 084 angular lever rh, 10523104 lv7 t 815hmv 466 544 268 490 board lamp, 10515640 lv7 t 815hmv 311 901 138 000 sealing ring 22x27 csn 02 9310 3, 10326969 lv7 t 816 205 501 132 4 fuel tank belt, 10338508 lv7 t 816 993 100 875 0 tube, 10326263 lv7krz pk2 3714250 lamp cover black out for cabcelling, 10344761 lv7 krz a31 32 6105000 door locklh and rh, 10317053 lv7 krz 255b 4224175 21 hoseassy adaptor, 10347474 lv7 krz 214b 1602069bracket bushing, 10328605 lv7 krz 236 1701042agasket, 10317682 lv7 krz 214 6103268 channel runside door window drop, 10333974 lv7 krz 256b3509280 hose, 10336944 lv7 krz 348532 p29 bolt, 10328950 lv7 krz 236 1601117 washer, 10348575 lv7krz 219u 2902624 bumper spring, 10342935 lv7 krz214b 4503050 shoe winch drum brake complete, 10318622 lv7 krz 214 6107042 b1 door rear weatherstrip, 10316012 lv7 krz 255b 3810027 union, 10315278 lv7 krz 255b 3519071 11 frt cyl lh bracketbracket lh frt cyl, 10317183 lv7 krz 255b 3125194pipe for branching air to rear lh wheel, 10328262lv7 krz 236 1601273 a3 spring, 10323418 lv7 krz311703 p29 nut m24, 10337982 lv7 krz 216303 p29stud m14x22x45 rear reducer hsg cover, 10344959lv7 krz 210 1801030 a pad rear, 10312407 lv7 krz 2143806014 p1 9a2 fuel level indicator transmiterswitch, 10347064 lv7 krz 200 3402015 wheel assysteering, 10337093 lv7 krz 349600 p29 u bolt nutm30, 10325133 lv7 krz 260020p 18c p29 pin, 10334050lv7 krz 256b 3570010 10 brake assy, 10322555 lv7krz 255b1 3506327 pipe assy to feed line shut offvalve, 10316062 lv7 krz 255b 3724059 batteryconnector jumper battery, 10343223 lv7 krz 214b4504013 a winch cable, 10326732 lv7 krz 100 3515310cock outlet valve, 10333946 lv7 krz 256b 3506311pipe withiout end connection length, 10323824 lv7krz 256b 3405043 packing ring, 10347324 lv7 krz 2148402680 catch hood top complete, 10332798 lv7 krzvk34 3720000 air pressure drop signal switch dk 34, 10352107 lv7 krz 258b 13506135 hose, 10322525 lv7krz 255b1 3506412 connecting hose assy, 10627940lv7 krz 256b 6804103 lock, 10347437 lv7 krz 214b1104474 fuel feed pipe flange gasket, 10332381 lv7krz ub125 3806010 g4 fuel level gauge, 10522953lv7 krz rh 1232 0912 0445 cooling water pipe tank, 10522030 lv7 krz rh 1000 9939 1765 bend pipecompressor drive to pump, 10522932 lv7 krz rh 1232 //bid details3 / 147 2186 pipe outlet cooler to crank case, 10333667 lv7 zil 130 6105013 a left hand lock assy, 10320475 lv7 zil 130 5603020 lock, 10332082 lv7 zil130 3507015 shoe assy, 10543367 lv7 zil 130 52060101 wind shield right hand glass, 10344422 lv7 zil307752 p locking ring, 10338262 lv7 zil 130 3513014bbrake no 2 air cylinder assy, 10336970 lv7 zil 1303401033 oil seal thrust ring, 10320414 lv7 zil 1305603018 a weather strip, 10334825 lv7 zil 306647 pmain shaft front roller bearing, 10324890 lv7 zil150v 6105194 inner handle escutheon assy, 10333608 lv7 zil 130 6104011 left hand windowraiser assy, 10315636 lv7 zil 120 3402015 a wheelsteering assy, 10333664 lv7 zil 130 6105029 lefthand latch assy, 10316153 lv7 zil 120 3502132anchor pin, 10346127 lv7 zil 131 3713230 binstrument pannel illumination lamp, 10332535 lv7zil 411149 p8 zil pipe union pressure regulatorunion, 10346145 lv7 zil 130t 3801010 b instrumentpannel type kp 204 assy, 10341389 lv7 zil 1313733010 electromagnet assy, 10320434 lv7 zil 1306103049 door lh vent window assy with removable, 10340615 lv7 zil 421174 p brake valve elbow 3 8, 10324574 lv7 zil 131 1103010 fuel tank cap assy, 10331772 lv7 zil 130 6105151 left hand handle assy, 10344291 lv7 zil 307190 p8 flance attachment stud, 10319835 lv7 zil 130 6103101 vent window lh latchand bracket assy, 10331356 lv7 zil 111 2915486bushing shock absorber head, 10565020 lv7 zil 1306903200 b passenger seat base edging, 10544428 lv7 zil258257 p2 1 lock wire wire catter pin, 10341534 lv7zil 130 1602036 a pedal seal 130 1602036, 10325606lv7 zil 157 2918122 shoe cap gasket, 10341900 lv7zil 150u 3713300 head lamp beam tail lamp pp6 b, 10307502 lv7 sca 377424 hollow nipple, 10301664lv7 sca 5340176327 813933 clamp loop, 10306598 lv7sca 171175 tee connector, 10304301 lv7 sca 243897bushing, 10301785 lv7 sca 249300 contr lamp, 10305809 lv7 sca 319750 ring set std, 10300509 lv7sca 1104804 wiper motor, 10303143 lv7 sca 305166damping capacitor, 10627558 lv7 sca 224665 switch, 10302322 lv7 sca 264467 sleeve, 10304037 lv7 sca235937 instrument lighting, 10305739 lv7 sca255178 housing, 10301221 lv7 sca 258756 lens, 10301145 lv7 sca 352140 plate scania, 10306776 lv7sca 187722 control h, 10305386 lv7 sca 265527brake drum, 10301936 lv7 sca 5331000054 o ring, 10303476 lv7 sca 391567 plate black out lighting, 10304866 lv7 sca 811233 hose, 10303609 lv7 sca561509 sleeve knob, 10302145 lv7 sca 162464 cover, 10301245 lv7 sca 355480 hub vibration damper, 10302247 lv7 sca 224207 cover front, 10305836 lv7sca 562551 level indicator10304419 lv6-mt6 2525-2030-5816 rubber hose waterpump to t connector, 10602534 lv7/fat6x6/ee/lv8519596 packing, 10602539 lv7/fat6x6/ee/lv8 512508packing set/packing set extn cyl, 10586823lv7/hmv6x6/mbrl/l&t f3569510 wheel nut -m 22x2.5, 10316208 lv7/ld b-4458603 s/a of hose-waterseparator fuel filter, 10320889 lv7/ld b-8780511hose assy-air comp drain to crankcase, 10362846lv7/mpvy 640-03-1613-1 inclined pipe, 10325720lv7/mpvy 015-l052-00 rocker switch, 10363221lv7/mpvy 115-43-0058-1 main harness dash board, 10353809 lv7/mpvy f-8501010 pipe assy powdercoated, 10313782 lv7/mpvy b8312165 s/a of hose 4 //bid details4 / 147 way-1 out to front parking, 10362866 lv7/mpvy 765-50-2783/84 cap, 10363043 lv7/mpvy 115-43-0032-1engine harness, 10362545 lv7/mpvy 640-03-1612-1intermediate pipe, 10362681 lv7/mpvy 640-03-1611-1bend pipe, 10609485 lv7/mpvy 101-107 expansionvalve, 10318097 lv7/mpvy 007-0029-00 pcb-gl-w15324v, 10363208 lv7/mpvy 115-43-0057-1 indoor lightand fan harness, 10325837 lv7/mpvy 012-l006-00 stopvalve - 5/8, 10324783 lv7/mpvy f-8500910 pipe assypowder coated, 10611570 lv7/sac10x10wc/al p-5104921 seal kit ext - 2 cylinder, 10611569lv7/sac10x10wc/al p-5104920 seal kit ext-1cylinder, 10611656 lv7/sac10x10wc/al p-5104925seal kit tandem pump, 10609483 lv7/sac10x10wc/alp0f00042 sensor pressure, 10611571lv7/sac10x10wc/al p-5104922 seal kit hor.outrigger cylinder, 10611607 lv7/sac10x10wc/alpk100004 thermostat aitf 50 24v, 10611567lv7/sac10x10wc/al p-5104918 seal kit columncylinder, 10611568 lv7/sac10x10wc/al p-5104919seal kit boom cylinder, 10609496lv7/sac10x10wc/al ppt00001 sump / oil pan gasket, 10611572 lv7/sac10x10wc/al p-5104923 seal kitvertical outrigger cylinder, 10347395 lv7/stlnf8047100 tail light, 10301530 lv7-awo 1301aa0501ninstrument cluster lbpv, 10302578 lv7-awo 5340-180691 069095 grommet transfer shift lever lbpv, 10527001 43/i-43/akl b6518506 cap female for 38 mmhose, 10517795 43/i-43/akl b6518525 delivery pipewith hose, 10517805 43/i-43/akl b6518515 pump assy, 10517889 43/i-43/akl b6518558 water level indicatorassy, 10547417 k7 4720-000180 hose rubber 19 mm x1.5 mtrs long, 10536954 k7 4720-000185 hose rubber100 mm x 3 mtr long , 10385384 k7 ikg/0274 pipe hosew/o coupling 70mm for 2-1/2 , 10382561 k7 p-2600642ball valve ss ic 76.2 mm, 10386731 k7 f-1500132impeller for tff large mk-v mtd on al, 10382035 k74210720259466 icn-4210002957 hose non metalic cpldelivery w/o, 10311363 lv7/itr/beml 6220-000161 taillight stop light lh sb-122-bn, 10319141 lv7/itr/beml50-331 knob lot 3 & 4, 10316124 lv7/itr/beml 50-66-41 hex nut m16 lot 1, 10317455 lv7/itr/beml 50-57-4hex screw m 6 x 20 lot 2 & 3, 10311345 lv7/itr/beml5920-000113 fuse electrical 5 amps, 10325521lv7/itr/beml 3120-000377 bushing sleeve steel ht od58 x id 50 , 10322584 lv7/itr/beml 5315-003175 pintoggle eye collar lot 2 to 4, 10318832 lv7/itr/beml50-319-128 hex nut m 10 lot 2 to 4, 10320743lv7/itr/beml 50-414 washer flat steel ms od 70 x id39 x 6 , 10321526 lv7/itr/beml 3020-000435 pulleygroove, 10322305 lv7/itr/beml 50-629-103 pipe l900x5/8 od x16 g seamless ms tube, 10323044lv7/itr/beml 50-641 cap assy lot 2 to 4, 10311515lv7/itr/beml 6220-000158 light convoy cross 10/8on, 10313491 lv7/itr/beml rtto-404400 extension bar20 len 400mm to is:7991*, 10314227 lv7/itr/beml 50-389-2 cover lot 3 & 4, 10314329 lv7/itr/beml 5365-008416 / 50-214-1 shim 2 mm thk, 10317621 lv7/itr/beml50-424 bituminous felt washer lot 2 to 4, 10317854lv7/itr/beml 50-481 nut assy, 10317931 lv7/itr/beml50-38-7 washer od:130 id:50 thk-10 lot-1, 10318974lv7/itr/beml 5306-057300 bolt machine, 10322538lv7/itr/beml 5315-003208 pin straight headed lot 2, 10323079 lv7/itr/beml 50-66-75 d shackle lot 2, //bid details5 / 147

Central Government/Public Sector

TRN :35711206 | 05 Nov, 2025

Tender Value : 45.0 Thousand

Amritsar - Punjab

Tender for gem bids for filter choke assembly pcb , igbt pcb , digital simplified regulator pcb , sfc mother board pcb , dc motor controller curtis pm

Related Searched Keywords : regulator board

List of regulator-board Tenders

Tender for gem bids for filter choke assembly pcb , igbt pcb , digital simplified regulator pcb , sfc mother board pcb , dc motor controller curtis pm

Get regulator board Tender Alert...

Related Searched Keywords : regulator board

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us