Filters

List of pvc-bend Tenders

List of latest pvc-bend Tenders in Indian Tenders. Click on any pvc-bend Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for pvc-bend Tenders.

All-Tenders (125)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

State Government

TRN :49055100 | 16 May, 2025

Tender Value : 38.90 Lacs

Dhanbad - Jharkhand

Tender for renovation of electro mechanical system at rural pipe water supply scheme at ojhadih katania under d.w and s mechanical division dhanbad , supplying all labour tools and tackles for taking out old and damage 10 h.p. v,t, pump set from intake well with all accessories, demolltion of mounting chanel for installation of new v,t. pump sets , s.i.t.c of electrically driven vertical turbine pump sets kirloskar/wpil/ mather&plate/jyotimake having discharge capacity of raw water 55 m3/h against total head of 25 mtr coupled with vertical hollow shaft sq. cage induction motor make (kirloskar/abb)/jyoti) operated on 415 ± 10% volts, 50 hz, 1460 rpm with sole plate, discharge head m.s. d.f. coloumn assembly random length of 5ft, total 50 ft s.s. line shaft s.s. socket, spider bearing with rubber cut less bush, cidf sluice valve- 1 no, cidf nr valve- 1 no pressure guage – 1 no etc all complete note- motor capacity should have 20% above of the pump , supplying all labour tools and tackles for making pcc foundation 2’x2’x1’ with all materials such as sand, stone chips, cement, foundation bolt etc all complete including fixing of sole plate for installation of new v.t. pump sets , providing floor/wall mounted cubical l.t power control panel fabricated with ms sheet and painted dust & vermin proof, proper ventilated consisting of a. proper distribution 63 amp copper bus bar 4 pole- 1 set b. microprocessor based tpn mccb 63 amp l&t/siemens/abb make with earth fault relay for incoming feeder – 1 nos c. mccb 32 amp tp l&t/siemens/abb make for outgoing feeder-2 nos d. 32a dp mcb for lighting – 1 nos. e. 0-500 v voltmeter with selector switch – 1 set ct operated ampere meter 0-50 with ct – 3 set, phase indication neon lamp- 6 nos. f. s.p.p – 2 nos. doing internal wiring with proper gauge of copper wire etc all complete job and testing on load – 1 set , cost towards supplying and laying of 6 mm2 x 3 core pvc insulated and pvc sheathed, 1.1 kv grade unarmouredcopper cable of reputed make and isi marked doing connection from panel to both motor , cost towards supplying and laying of 70 sq. mm x 3.5 core pvc, insulated and pvcshethed, 1.1 kv grade armouredalluminium cable of reputedmake and isi marked for doing connection from pole to main switch to panel , cost towards making cable mouth for a. 6 mm2 – 24 nos. , b. 50 mm2 – 16 nos. , supply & fixing 3 ton capacity triple gear chain pulley block with 6 mtr lifting chain of reputed make & i.s.i. marked , cost for making new common header with supply and fitting of 6” dia heavy duty g.i. pipe 6 mtr, 6”dia bend-2 nos., 6”dia tee- 1 no, 6” dia flange-12 nos., rubber insertion – 10 kg nut bolt washer – 10 kg with cutting of pipe in required length and and doing welding as required length and doing welding as required all complete job with materials and labours charges. , making chemicalwith required materials and labour tool & tackles , supply & laying of 8 swg copper/g.i. wire for making earthing connection into from earthing station to panel to motor , cost for supply and fitting 100 amp tpn main switch/switch disconnector and doing all line connection , sitc of 40kva servo control automatic voltage stabilizer suitable for input voltage 220v to 450v and out-put voltage 415v ± 1% 3phase 50hz with copper wound transformer (oil cooled) as mentioned below. the stabilizer self function satfictorilyeven if in coming supply is unbalanced between phases within range of 10% . the stabilizer should be constructed in cubical box, with bidirectional wheels for easy handle, necessary monitors in user’s control on front panel such as indication, alarm, volt meter and selector switch for measuring input and output voltage, auto/manual selector switch, raise /low push button etc. suitable capacity termination strips and bus-bars for incoming and outgoing cable should be provided. all 3 phases shall be independently monitored and corrected . following protections and indication shall be incorporated as per isi 9815 a) over voltage/under voltage b) single phasing c) cut off contactor with electronig output sensing unit d) suitable change over switch and earthing , cost for adding transformer oil of reputed make isi certified upto level , cost for supplying and fitting of 40watt led light with its bracket and doing wiring connection etc all complete , supplying all labour tools and tackles for taking out old and damaged c/f pump set with all accessories, demolition of foundation for installation of new hsc c/f pump set , sitc of electrical driven horizental split casing c/f pump set [make: kirloskar/wpil/jyoti/ mather & plate] having discharge capacity of clear water 55 m3/h against a total head of 72mtr coupled with tefc squirrel cage induction motor[make: kirloskar/abb/jyoti] operated on 415v, 3 phase, 50hz, 1460rpm mounted on common ms fabricated base plate with suitable size of cidf sluice valve-1no, cidf nr valve-1no, foot valve-1no, pressure gauge-1no, tyre coupling-1set etc all complete , supplying all labour tools and tackles and making pcc foundation of 4’ x 3’ x 3’ with all materials such as cement, send, stone chips, foundation bolt-6nos etc all complete and plastering and punning over exposed surface. , providing floor/wall mounted cubical l.t power control panel fabricated with ms sheet and painted dust & vermin proof, proper ventilated consisting of g. proper distribution 100 amp copper bus bar 4 pole- 1 set h. microprocessor based tpn mccb/ 100 amp l&t/siemens/abb make with earth fault relay for incoming feeder – 1 nos i. mccb 63 amp tp l&t/siemens/abb make for outgoing feeder-2 nos j. 32a dp mcb for lighting – 2 nos. k. 0-500 v voltmeter with selector switch – 1 set ct operated ampere meter 0-100 with ct – set phase indication neon lamp- 6 nos. l. s.p.p – 2 nos. doing internal wiring with proper gauge of copper wire etc all complete job and testing on load – 1 set , cost towards supplying and laying of 6 mm2 x 3 core pvc insulated and pvc sheathed, 1.1 kv grade unarmouredcopper cable of reputed make and isi marked doing connection from panel to both motor , cost towards supplying and laying of 50 mm sq. x 3.5 core pvc insulated and pvc sheathed, 1.1 kv grade armoured aluminium cable of reputedmake and isi marked for doing connection from pole to main switch to panel , cost towards making cable mouth for a. 6 mm2 – 24 nos. , b. 50 mm2 – 16 nos. , cost for making new common header with supply and fitting of 6” dia heavy duty g.i. pipe 6 mtr 6”dia bend-2 nos. 6”dia tee- 1 no 6” dia flange-12 nos. rubber insertion – 10 kg nut bolt washer – 10 kg with cutting of pipe in required length and doing welding as required length and doing welding as required length and doing welding as required all complete job with materials and labours charges , making chemical earthing with required materials and labour tool & tackles , suuply& laying of 8 swg copper/g.i. wire for making earthing connection into from earthing station to panel to motor , cost for supply and fitting 100 amp tpn main switch/switch disconnector and doing all line connection , providing& erecting of 60kva servo control automatic voltage stabilizer suitable for input voltage 220v to 450v and out-put voltage 415v ± 1% 3phase 50hz with copper wound transformer (oil cooled) as mentioned below. the stabilizer self function satfictorilyeven if incomming supply is unbalanced between phases within range of 10% . the stabilizer should be constructed in cubical box, with bidirectional wheels for easy handle necessary monitors in user’s control on front panel such as indication, alarm, volt meter and selector switch for measuring input and output voltage, auto/manual selector switch, raise /low push button etc. suitable capacity termination strips and bus-bars for incoming and outgoing cable should be provided. all 3 phases shall be independently monitored and corrected . following protections and indication shall be incorporated as per isi 9815 a) over voltage/under voltage b) single phasing c) cut off contactor with electronig output sensing unit d) suitable change over switch and earthing , cost for adding transformer oil of reputed make isi certified upto level , cost for transporting of taken out pump set and other materials from pump plant to store dhanbad

Central Government/Public Sector

TRN :49055122 | 29 May, 2025

Tender Value : 40.00 Lacs

Palam - Delhi

Tender for comprehensive maintenance and certain misc b/r works in tech area at af stn palam under ge (af) palam, delhi cantt - 10; 1.00 taking down cement plaster on brick, stone or concrete surfaces of walls etc incl racking out joints hacking for key scrubbing down with water etc and removing the debris from site to out site mod land complete all as specified and directed by engr-in-charge . 2.00 m&l for 10mm thick rendering of ready mix mortar of approved make on brick work or concrete surfaces on internal walls, finished the surface even and smooth without using extra cement as on wall as whole or in patch etc complete all as specified and as directed. make- birla (hil) or its equilent. 3.00 m&l for 15mm thick rendering of ready mix mortar of approved make on brick work or concrete surfaces on external walls, finished the surface even and fair without using extra cement by using dr. fixit (wpc) @ 3% of wt of cement content complete all as specified and as directed. note:- water proofing compound shall be measured and paid seprately. 4.00 m&l for 5mm thick cement plater of ready mix mortar of approved make as on ceiling & plastering to be finished even & smooth without using extra cement complete all as specified and as directed. make- birla (hil) or its equilent. 5.00 supply only integral water proofing compound complete all as specified and as directed. 6.00 m&l for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkalic resistent primer complete all as specified and as directed 7.00 m&l for applying two coats of 100% premium acrylic emulsion paint having voc less than 50 gm/ltr and uv resistance as per is 15489-2004, alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives @1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.9 litre /10 sqm over new surfaces complete all as specified and as directed. 8.00 m&l for preparation of newly plastered surfaces of ceiling and applying two coats of oil bound distemper over a coat of alkalic resistent primer complete all as specified and as directed. 9.00 m&l for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster (1:4) (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified and as directed. note:- payment for providing grooves shall be measured and paid separately. 10.00 m&l for forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications complete all as specified and as directed. 11.00 demolition of cement concrete (un reinforced) in ground floors and pavings n. exc 15 cm thickness (below or above ground level) and removing the debris from site to out site mod land complete all as specified and as directed. 12.00 m & l for 75mm thick cement concrete (1:3:6) type c2 (using 40mm graded stone aggregate) as in plinth protection, finished even and smooth without using extra cement, including making joints 12 mm wide to the full depth of pcc at every 3 metres and at every change of direction and filling the same with & including bitumen 85/25 and sand in the proportion of (1:3 ) by weight complete all as specified and as directed. 13.00 m&l for 75mm thick pcc (1:3:6) type c2 (using 40mm graded stone aggregate) as in path and paving, finished even and smooth without using extra cement complete all as specified and as directed. 14.00 m&l for 25 mm thick pcc (1:2:4) type b1 (using 20mm graded stone aggregate) as in floor, finished even and smooth with using extra cement complete all as specified and as directed. 15.00 m&l for plain cement concrete (1:3:6) type c1 (using 20 mm graded stone aggregate) as in surface channel/drain complete all as specified and as directed. 16.00 extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and as directed. 17.00 supply and fixing in repairs, sfrc drain cover any size, 75mm thick laid over existing drain complete all as specified and as directed by engr-in-charge. notes: - (i) make of sfrc manhole/drain cover and frame : (a) m/s ps concrete.(b) m/s kk manhole.(c) or equivalent as approved by ge. (ii) contractor will provide manufacturer test certificate of sfrc cover . 18.00 dismantling wall and ceiling boards ( fibre, pulp, insulation etc.) or insulation boards / slabs / blankets, any thickness, including fillets complete all as specified and as directed. 19.00 m & l for provding false ceiling of 12mm thick fine fissure board sharped finished mineral fiber accountic false ceiling tiles with back of the duly sanded and finshed with a coat of protective paint and front duly finished false system of size (600x600) mm having noise reduction co-efficient of 0.55 light reflection of 80% thermal conductivity k=0.057 w/wwc and humidity resistance of 95% fixed to true look pvc die kl -24 suspension system (hot dipped aglvanised steel section) of exposed t section consisting of perimeter wall angle of size (24x24) mm of thickness 0.45 of mm c/c universal main runner of t shape with double rotary siticing of size (38x25) mm of lenght 1200mm made from 0.33gs steel of lenght 3.60 mtr to be spced at 600x 600mm size) c/c cro runner t shape wtih double rotary siticing of size (30x24)mm of length 1200mm made 0.25 thick gs sheet spaced @ 600mm c/c (600mm 600mm) size complete all as specified and directed by engineer -in- charge. 20.00 taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 sqm each including cutting holes in walls of appropriate size for insertion of cement concrete blocks for hold fasts complete all as specified and as directed. 21.00 taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size exceeding 1.50 sqm but n. exc 4.0sqm each including cutting holes in walls of appropriate size for insertion of cement concrete blocks for hold fasts complete all as specified and as directed. 22.00 taking down shutters of any description of size n. exc 1 sqm each complete all as specified and as directed. 23.00 taking down shutters of any description of size exc 1 sqm and n exc 2 sqm each complete all as specified and as directed. 24.00 taking down shutters of any description exc 1 sqm and n exc 2 sqm each and re-fixing in the same opening after necessary repairing viz shifting of hinges/tower bolt / handle position etc complete all as specified and as directed. note:- cost of screws/nails and minor items shall be deemed to be included in the unit quoted rates. 25.00 s&f anodised aluminium powder coated frame for door, windows, ventilators, partition wall with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed 26.00 s&f anodised aluminium powder coated door shutter, aluminium section wt 0.55 kg/m including neccesary joining cleats, glazing clips, rubber neoprene packing, aluminium handle 2 nos in each door, hinges, anodised aluminium snap beading screw etc. complete all as specified and as directed. 27.00 s&f anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised, handle 2 nos in each window, aluminium fittings such as peg stays150mm long (1 no.), hinges type b-21100mm long (2 no.), suitable handle (1no.) complete all as specified and as directed. 28.00 s&f aluminium anodised with powder coating (minimum thickness of powder coating 50 micron) grill of design and parttern as approved by ge including aluminium beading complete all as specified and as directed. 29.00 s&f 5.50mm thick tinted, sheet glass of selected quality fixed to aluminium frame work complete all as specified and as directed. 30.00 m&l for 12mm thick prelaminated particle board, exterior grade, prelaminated both side with decorative choice lamination & fixed with screws to timber/aluminium frame complete all as specified and as directed 31.00 s & f door closer hydraulically regulated designation no 3 universal type suitable for door shutter of 851 to 1000 mm in width of aluminum body (die cast) weight between 61 to 80 kg complete all as specified and as directed. 32.00 m&l double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminum alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other party made of mild steel heavy duty complete all as specified and as directed. 33.00 s & f mild steel mortic lock vertical type size 100mm 4 levers complete all as specified and as directed. 34.00 s&f aluminium tower bolt of extruded section, 150mm length of bolt and fixed with screws complete all as specified and as directed. 35.00 s&f aluminium door stopper double legged with rubber shoe 75mm long fixed to door shutters complete all as specified and as directed. 36.00 m & l 2nd class hard wood plain, solid, straight chowkhats, and frame wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and as directed. 37.00 s&f for 30mm thick factory made flush shutter, solid core construction with block board core and plywood face panels commercial type on both sides complete all as specified and as directed. 38.00 s&f for factory made single extruded wpc (wood polymer composit) solid door/window and other frames/chowkhat of size 50x100 mm comprising of virgin pvc polymer of k value 58-60 (suspension grade) calcium carbonte and natural fibers (wood powder/rice husk/wheat husk) and non toxic aditives(maximum toxicity index of 12 for 100 gms) fabricated with full body threaded star headed ss screws having minimum frame density of 750 kg/cum screw withdrawl strength of 2200 n(face) & 1100n(edge) minimum compressive strength of 58 n/sqmm modules of ealsticity 900 n/sqmm and resistance to spread of flame of class a category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with ms hold fast/ lugs/ss dash fasteners of required dia and length complete as per direction of enger-in-charge. make- m/s rajshree plastiwood ltd or its equivalent as per list of make. 39.00 s&f for factory made single extruded wpc (wood polymer composit) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of k value 58-60 (suspension grade) calcium carbonte and natural fibers (wood powder/rice husk/wheat husk) and non toxic aditives(maximum toxicity index of 12 for 100 gms) fabricated with full body threaded star headed ss screws having minimum frame density of 650 kg/cum screw withdrawl strength of 1800 n(face) & 900n(edge) minimum compressive strength of 50 n/sqmm modules of ealsticity 850 n/sqmm and resistance to spread of flame of class a category with property of being termite/borer proof, water/moisture proof and fire retardant. wpc to be laminated with pvc foil of minimum 14 microns thick of approved design pasted with hotmelt adhesiv on both faces of shutter and fixing with stailess steel butt hinges of required size with necessary full body threaded star headed counter sunk ss screws all as direction of enger-in-charge. make:- m/s rajshree plastiwood ltd or its equivalent as per list of makes. 40.00 dismantling of floor, hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles and rubbish off the premises complete all as specified and as directed. 41.00 m&l for vitrified ceramic tiles 8-10 mm thick, 1st quilaty (square/rectuangular) polished, double charge shade, area of each tiles exceeding 0.36 sqm but not exc. 0.42 sqm, as in floors etc. set and jointed with neat cement slurry and pointed in white or coloured cement to match with and including over15mm thick screed bed in cement mortar (1:6) complete all as specified and as directed. 42.00 description all as per srl item no. 39.00 bove but as in skirting over 10mm thick plastering with cm (1:4) complete all as specified and as directed. 43.00 m &l for ceramic coloured/ printed non-skid tiles of size 7 to 8 mm thick( square / rectangular) area of each tile exceeding 0.06 sqm but n exc 0.16 sqm laid as in floors, set and jointed with neat cement slurry with and including over 15 mm thick screed bedding layers of cement sand mortar (1:4) and pointed with coloured cement to match with surfaces of tiles complete all as specified and as directed. 44.00 m&l for glazed ceramic coloured tiles (colour & shade as approved) of size (450x350)mm x 7mm thick as in vertical surfaces as in skirting and dado, set and jointed in neat cement slurry with amd including over 15mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and as directed. 45.00 s&f in repair wash hand basin, vitreous china, flat back (550x400)mm size, white including pvc waste coupling 32mm size, pvc waste pipe 32mm bore, pair of brackets of mild steel (35 x 35 x 6)mm size including one mixer cast copper alloy 15mm bore, one brass stop valve 15mm bore and one pvc connection15mm size with ptmt nuts of length 450mm long complete all as specified and as directed by engineer-in-charge. 46.00 supply & fixing in repair vitreous china ewc super constellation including flushing cistern of size (83x37x66)cm with s trap complete all as specified and as directed. 47.00 supply & fixing in repair vitreous china urinal pot white including partition, waste pipe, screw with wall fixing complete all as specified and as directed. 48.00 s&f in repairs two way wall mixer with popup waste system, hot and cold facilites and 450 mm long braidaed hoses chromium plated complete all as specified and as directed . 49.00 s&f in repair health faucet with double lock 1 meter brass plated stainless steel flexible hose and wall hook complete all as specified and as directed. 50.00 s & f in repair copper alloy cp toilet paper holder complete all as specified and as directed. 51.00 m&l for replacement of 100mm ci floor/nahani trap with grating including jointing and breaking/ dismantling any type of floor and making good cement concrete type b-1 (1:2:4) and testing after repairs and taking down existing trap etc complete all as specified and as directed. 52.00 s&f in repair, brass chromium plated tubular towel rail, 20mm dia, d type, 60cm long between flanges complete all as specified and as directed. 53.00 taking up or down 15mm steel tubing and connections in walls, ceilins, floors, etc including cleaning for refixing or removal to store complete all as specified and as directed. 54.00 m&l for gi tubing, 15mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floors etc complete all as specified and as directed. 55.00 m&l for cutting chases, pinning in making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc, and cutting chases for concealed water tubing or concealed conduit wiring, etc and making good cutting not exc 10 cm girth as in wall complete all as specified and as directed. 56.00 s&f in repair 15mm bore cast copper alloy, cp angle cock, screwed down, high pressure, with crutch or butterfly handles, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. 57.00 s&f in repair pvc connections 15mm size with ptmt nuts of length 450mm and fixed complete all as specified and as directed. 58.00 s&f in repairs pvc connections 15mm size with ptmt nuts of length 600 mm and fixed complete all as specified and as directed. 59.00 s&f in repair cast copper alloy cp soap dish complete all as specified and directed. 60.00 s&f in repair bib taps with wall flange 15mm bore, chromium plated, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed. 61.00 s&f in repair pillar cock, foam flow cast copper alloy, chromium plated, fancy type, 15 mm dia, capastan heads, screwed down high pressure complete all as specified and as directed. make:- cat no 8304 of make prayyag or equivalent as per list of makes. 62.00 s&f in repair plastic water closet seat cover, white/black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed. 63.00 s&f in repair pvc valveless, syphonic action type, flushing cistern low level, 10 litre capacity , white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed. 64.00 s&f in repair 610 mm long pvc waste pipe flexible type 25 mm dia suitable for couplings 32 mm / 40 mm dia complete all as specified and as directed. 65.00 s&f in repair (600 x450) mm fancy type or bevelled edge mirror of selected quality glass, mounted on 6mm thick ac building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed. 66.00 s&f in repairs 15 mm bore bib taps standard of ptmt any colour high pressure screwed for iron pipe and fixed complete all as specified and as directed. (minimum weight 90 gms). 67.00 s&f in repairs 15 mm two in one angle valve cast copper alloy, chromium plated with wall flange and fancy type with high pressure screwed down and with cp flange of same make complete all as specified and as directed . 68.00 m&l for 18-20mm thick granite (of jet black ) work (table rubbed and polished ) in steps, jambs, pillars, window cills, cooking plateforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed. note:- the cost of half round moulding shall be deemed to be included in unit rate. 69.00 dismantalling water tanks and removal from site of capacity exc 250 ltr and not exc 500 ltr complete all as specified and as directed. 70.00 m &l for 500 litres capacity rotational moulded polyethene water storage tank (cylindrical vertical with closed top), white, three layers, hoisted and fixed in position complete all as specified and as directed. 71.00 supply and fixed ball brass valve high pressure with polythene float and fly nut complete to bore of pipe 20mm complete all as specified and as directed. 72.00 demolition of brick work or stone buillder built in cement mortar of any description complete all as specified and as directed. 73.00 m&l for brick work with sub class b works, straight or curved on plan exceeding 6m mean radius, built in cement mortar (1:6) complete complete all specified and as directed. 74.00 dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. 75.00 s&f mild steel work such as angle iron post, flat iron in fencing including cutting as making doubble swan neck i.e. y shaped including welding with proper overlapping & welding ms plate with angle iron bottom as directed, drilling holes notching for wire etc embedded in concrete fixed vertically conforming to fe 290 grade e-165 complete all as specified and as directed. note:- embedded portion of angle iron post shall be treated with tar of coat of tar black paint and cost of the same shall be deemed to be included in unit rate. 76.00 m&l for preparation of newly steel surfaces of any description over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer of any height complete all as specified and as directed. 77.00 s&f for concertina coil with punched tape of 600 mm dia (when stretched), centre core wire of minimum 2.5 mm dia of mild steel wire conforming to is 280-2006 with galvanised coating of steel concertina coil as per requirements laid down for medium coated wire in is : 4826 hot dipped galvainsed coating of round steel wires. conretina coil shall be fixed in diamond shape with the help of dovetail two handle and spikes shall be fixed at both end of coil,minimum straight length of the wire 150 rm for 10 rm of work ,minimum weight 13.5 kg for 10 rm of work including dismantling of existing concertina coil complete all as specifed and directed by engr-in-charge. (note:- the actual weight of concertina coil brought by the contractor at site shall be ascertained by boo as ordered by ge). 78.00 s&f for concertina coil with punched tape of 900 mm dia (when stretched), centre core wire of minimum 2.5 mm dia of mild steel wire conforming to is 280-2006 with galvanised coating of steel concertina coil as per requirements laid down for medium coated wire in is : 4826 hot dipped galvainsed coating of round steel wires. conretina coil shall be fixed in diamond shape with the help of dovetail two handle and spikes shall be fixed at both end of coil,minimum straight length of the wire 180 rm for 10 rm of work ,minimum weight 16.5 kg for 10 rm of work including dismantling of existing concertina coil complete all as specifed and directed by engr-in-charge. (note:- the actual weight of concertina coil brought by the contractor at site shall be ascertained by boo as ordered by ge). 79.00 dismantling of fencing wire, barbed wire any type and description complete all as specified and as directed. 80.00 supply and fixing galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2 mm dia barbed of 75mm spacing and straining and fixing to any type of standard rail, straining bolt including securing or tying at crossings with and provision of galvanised mild steel wire staples or steel pins etc as directed (each line wire to be measured) complete all as specified and as directed. 81.00 m&l for cuting holes in brick walls exc half brick but n.exc one brick, built in cement mortar for fixing holdfasts in jambs of existing opening and making good complete all as specified and as directed. 82.00 m&l pcc (1:3:6) type c1 (using 20 mm graded stone aggregates) as in hold fast block including necessary form work complete all as specified and as directed. 83.00 s&f mild steel work framed such as grill, gratings, etc with ends of bars shouldered and /or riveted, or forged into spikes, framed guard bars barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar work conforming to fe.290.gde-e-165. complete as specified and as directed. 84.00 dismantling of fencing wire mesh, any type of any description complete as specified and as directed. 85.00 fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete as specified and as directed. 86.00 supply only chain link ms galvanised fencing, 4mm dia gi wire mesh size 100mm x 100mm complete as specified and as directed. 87.00 s&f mild steel screw bolts 12 mm dia (machine made) with hexagonal heads at one end and screwed other end to be fitted with washers (02 nos.) and one hexagonal nut, length of bolt exe 5 cm and n exe 10 cm complete as specified and as directed. 88.00 s&f mild steel fabricated round bars 10mm dia as in horizontal bars for chain link fencing incl necessary hooking at ends all as complete as specified and as directed. 89.00 excavation in post hole (or similar holes) each n.exc 0.50 cum getting out returning, filling in and ramming earth around in layers n. exc 25cm watering and removed surplus soil to a distance n. exc 50m and making good surface in soft/loose soil complete as specified and as directed. 90.00 supply and fixing in repairs, pre cast cement concrete jallies, 35 mm thick, type b0 1:2:4 (using 12.5 mm graded crushed stone aggregate) including wire fabric set and jointed in cement mortar (1:4) complete as specified and as directed. 91.00 s&f in repair aluminium composit panel (acp) sheet with 1x1.5 aluminium tube over the framed/ beam of gates. acp shall meet under mentioned technical requirements:- (i) coating on front : high quality polymer resin.(ii) core : fr core (fire retardant)(iii) thickness : 4mm(0.5 mm+3.0mm+0.5mm) (iv) weight : 7.50kg/sqm(v) width: 1200mm(vi) length: 1200 to 2400mm(vii) structure: aluminium panel are protective film,clear coating pvdf,primer coating,antirust layer,aluminium skin and polyethylene.(viii) temp resistance : between -50c to +80c(note:- the quoted rate is deemded to be included necessaryy scaffolding required and joint sealing) 92.00 s & f in repair 12mm thick toughened glass fixed with double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminum alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other party made of mild steel heavy duty and stainless steel handle purpose made on both side with locking machanism and with necessary stopper etc complete all as specified and as directed. 93.00 demolition and breaking up drain pipe 75/100mm dia ( salt glazed ware, ac or pvc) of any type complete all as specified and as directed. 94.00 s&f 75 mm dia pvc (swr) pipes single socketed in any length with rubber ring joints fixed to walls including suitable clamps after every one meter of interval complete all as specified and as directed. 95.00 s&f 110 mm dia pvc (swr) pipes single socketed in any length with rubber ring joints fixed to walls including suitable clamps after every one meter of interval complete all as specified and as directed. 96.00 s&f in repairs pvc(swr) bends any radius, 75 mm bore complete all as specified and as directed. 97.00 s&f in repairs pvc(swr) bends any radius, 110 mm bore complete all as specified and as directed. 98.00 hacking out old broken glass (any thickness, size, quality or description) from wooden frames or steel, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and as directed. 99.00 s&f sheet glass 4mm thick ordinary quality and glazing with oil putty or rubeer bedding in square n. exc 0.5 sqm in each pane complete all as specified and as directed. 100.00 s&f in repairs of sink with drainage board, made out of stainless steel 1mm thick, kitchen or laboratory with plugs, washes and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever bracket and connecting union to pipe over all size (915x460)mm with bowl size (410x330x160)mm complete all as specified and as directed. 101.00 s&f in repair brass chromium plated shower rose,125 mm size fixed to 15 mm bore iron pipe complete all as specified and as directed. 102.00 s&f in repair water closet vitreous china squatting pan, orissa pattern size (580x440)mm white with integral foot rests (excluding flushing cistern and flush pipe) and including with p or s trap complete including provison of lime concrete bedding fixed in repair complete all as specified and as directed. 103.00 m&l for gunniting work to rcc work in column, flooring, side walls, beam, slab, etc by removing loose concrete cover etc, cleaning of surface with wire brush and applying epoxy paint to rusted reinforcement and s&f welded wire mesh fabric or wire net less than 95 x 95x 3 mm tied to existing reinforcement with nails,adhesive plaster grade for concrete and providing gunniting pressure 2.0/2.5kg/sqm with admixture 1 part of cement and 3.5 part of sand with average thickness 40 mm and making the surface even including 15mm thick plastering in cm 1:4 on brick or concrete surfaces including finishing the surfaces even and smooth, without using extra cement including necessary form work to be carried out,complete all as specified.(note.- wherever reinforcement required shall be measured and paid seperately) 4. structural steel steel authority of india limited (sail) brand: sail / rashtriya ispat nigam limited (rinl) brand: rinl / tata iron & steel company (tisco, or tata steel) brand: tata / m/sjindal steels and power ltd. brand: jindal 5 factory made paneled/ glazed /gauged door shutters m/s mp wood product indore, m/s jain doors pvt ltd sonipat, goyal industiral corporation new delhi, shri krishna industries, panchkula, 6 factory made flush door shutters m/s green ply industries, m/s centuary ply, m/s dura ply. mysore chip board, archid, swastik ply wood, m/s jain doors pvt ltd 7 pvc door frame/shutters sintex, rajshri plastiwood ltd, m/s dura plast extraction pvt ltd, m/s fenesta, ecocell,accucell 8 frp door frame and shutter selected products co., sintex, rajshri plastiwood ltd, accure polytec pvt ltd ,ecocell, fiberways 9 upvc window/doors fenesta, ncl veka, madhu industries, h2o solutions, yashpoly,accucel, okotech, aseco (m/s ashish industries) 10 iron mongery mowjee, m/s kitch architectural product pvt ltd, rs industries. 11 hydraulic door closer everest, universal, godrej 12 particle board(veneered & unveneered laminated)/ block board kitply, nova pan industries, new delhi, m/s green ply industries ltd, archid ply, bhutan board, dura board mysore chip board ltd 13 plywood for general purposes dura ply, archid ply, bhutan board,archid board, century, durian, mysore chip board ltd 14 decorative laminates archid lam, sunmica, merino, lam, mysore chip board,greelam 15 terrazzo tiles ntc, nitco, eurocon, duracrete 16 glazed ceramic/non skid wall/floor tiles kajaira, johnson, agl, qutone , somany, nitco, orient bell ,vitero, sunhearrt ceramik, varmora 17 vitrified tiles (polished, unpolished & glazed, normal/ anti skid) kajaira, johnson, agl, qutone , somany, nitco, orient bell,vitero,sunhearrt ceramik, varmora 18 hdpe storage water tanks sintex, supreme,plasto,polycon 19 sanitary appliances /fittings(chinaware) hindware,parryware,cera,jaquar, kohler, prayag aproyale,somany 20 water closet seats and cover (solid bakelite) thermostat moulded toilet seat cover parryware, jaquar, prayag somani,commander,cera,neycer 21 pvc flushing cisterns hindware, commander, parryware, cera ,jaquar, johnson pedar, neycer 22 stainless steel kitchen sink with or without draining board, plate rack nirali,cera,diamond,jainco,shakti prayag, (silver shine) m/s bluestar sanitary industries 23 ball valves (horzontal plunger type) dripless faucets india, flowjet , ball valves inida. 24 shower roses chromium plated (swivel type) gem,jaquar, jal 25 bath room fancy fittings jaquar,gem,marc, jalangi 26 bib taps and stop taps (cp),pillar tap, fancy fittings jaquar, parko, gem, marc 27 bathroom cabinets jaquar, cera, commander, parryware .... more in document

Central Government/Public Sector

TRN :49055191 | 05 Jun, 2025

Tender Value : 7.92 Crore

Deesa - Gujarat

Tender for tender for provn of fencing and gate at af stn deesa (ph-ii); 1 b/r works 2 site clearance of area including shrubs, vegetation, grass, bush, weed, trees and saplings n. exc. 30 cm girth complete all as specified and directed. 3 excavating in post hole each n exc. 0.50 cum, getting out in soft/loose soil including returning, filling in and ramming earth or broken rubble mixed with earth around, in layer not exc. 25 cm, watering including clearing away all grass vegetation, saplings, shrubs, brushwood, undergrowth, roots and trees n. exc. 30 cm girth (measured one meter above ground level) and removing rubbish/ surplus soil upto a distance of 50 meters outside and making good surface complete all as specified and directed.note : necessary dewatering of water if requried shall be included in the unit rate of item. 4 excavation in trenches, n nexc 1.5m wide and n. exc 1.5 m in depth, for foundation manholes, wells, drain etc.getting out in soft/loose soil including clearing away all grass vegetation, saplings, shrubs, brushwood, undergrowth, roots and trees n. exc. 30 cm girth (measured one meter above ground level) and removing rubbish/ surplus soil upto a distance of 50 meters outside complete all as specified and directed. 5 m & l for cement concrete 1:2:4 type b-1 (20 graded stone aggregate) as in post holes includingcompaction by vibratorcomplete all as specified and directed. 6 m & l for cement concrete 1:4:8 type d-2 ( 40 mm aggregate)in foundations, filling and mass concrete complete all as specified and directed. 7 s & f mild steel work as in fencing posts and struts in fencing including cutting tops of shape as directed, drilling holes, notching for wire, etc.,flat iron fillets and round bars with hooks at ends (for securing wire mesh etc.) incl all necessary drilling, bolting or riveting, etc, and similar work confirming to fe -290 gde e-165 complete all as specified and directed. 8 supply only chain link ms galvanised fencing, any size or type complete all as specified and directed. note :i) chain link of mesh size preferably 100 mm mesh 10 gauge thickness will be provided, however the size may be changed after written approval of ge.ii) the weight of chain link fencing shall be ascertained by boo ordered by ge 9 fixing only chain link fencing including line wires,any mesh,size and type to any type of standards,rails,straining bolts,etc. including provision of binding wire complete all as specified and directed. note : chain link of mesh size preferably 100 mm mesh 10 gauge thickness will be provided,howeverthe size may be changed after written approval of ge. 10 s & f 5-10 mm diameter of shank mild steel screw bolts ( machine made) with hexagonal or square heads at one end and screwed the other,or screwed both ends.each screwed end to be fitted with washers and one hexagonal or square nut, n exc. 5 cm long complete all as specified and directed. 11 m & l for mild steel work 10 mm dia round bars as in fencing cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 12 s & f galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, complete all as specified and directed. (each line wire to be measured) 13 material & labour for 610 mm dia punched tape concertina coil fencing stretches ( supporting wire of the same material as concertina coil ) having stranding specifications average weight not less than 1.06 kg/m incl coating of px2 compound (anti rust) and fixed in angle iron brackets on compound wall/ fencing with and including all scaffolding if required complete all as specified and directed. 14 m&l preparation of new steelsurfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. 15 m & l for new steel primed surfaces of any description, n.exc 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. 16 m&l brick work with sub class b bricks straight or curved on plan exceeding 6m mean radius bulit in cm 1:6 complete all as specified and directed. 17 m&l for cement concrete (1:2:4) type b-0 using 12.5 mm graded aggregate as incopingetc. including weathering, slighty rounded or chamfered angle including necessary form work complete all as specified and directed. 18 m&l rendering 10mm thickin cement mortar 1:6 on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. 19 m & l, two coats of cement based paint over one coat of alkali resistant primer in including preparation of new surface (preparing surfaces plastered or unplastered) on internal wall complete all as specified and directed. 20 s&f 110 mm bore pvc (swr) pipes single socketed in any length with rubber ring joints fixed to walls as in weep holes complete all as specified and directed. 21 m&l rcc m-25 (20mm graded aggregates) work as in foundation, including rafts, footing beam etc. complete all as specified and directed. 22 m&l rcc m-25 (20mm graded aggregates) work as in columns, pillars, piers, post and struts etc. complete all as specified and directed. 23 m & l for form work to side of concrete foundation, footing, bases of columns, raft sides and soffits (if any) of foundation and plinth beams with fair finish surface etc.complete all as specified and directed. 24 m & l for form work to sides of column with fair finished surface of concrete etc complete all as specified and directed. 25 m & l for mild steel bars (tmt) 10 mm dia and over, cut to lenth bent to shape required, including cranking bending spirally for hooping for columns hooking end and binding with steel wire or sequring with clips complete all as specified and directed. 26 m & l for mild steel bars (tmt) 8 mm dia and over upto and including 10 mm dia in stirrups, spaces and binder as in column complete all as specified and directed. 27 s&f steel sections fe-290(gde-e-165) forframed work as in doors or gates of angle or other section with gusset plates , rails, braces with ornamental and intricate design complete,drilled for fixing of steel sheeting or other covering. door, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fiftting (exc. of steel sheeting or other covering ,running rails and guides ) and hanging ; also fastening and fixing complete all as specified and directed. 28 m& l 20mm thick granite (of any type) work in steps, jambs,clading topillars, window-cills, cooking plateform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite and 20mm thick screed bed in cm 1:4 complete all as specified and directed. 29 returning, filling in, including spreading, levelling, watering and well ramming in layer not exc 25 cm complete all as specified and directed. 30 rough excavation not exceeding 1.5 m deep and getting out in soft/ loose soil complete all as specified and directed. 31 forming embankments including raising (or lowering) earth, spreading in layers n exc. 30 cm thick; watering, ramming/ rolling and finishing to required size, shape, etc., n exc. 1.5 m high from base complete all as specified and directed. 32 removing excavated material ( soil ) exc 250m but n. exc. 500mand depositing where directed complete all as specified and directed. 33 m&l framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar workconforming to fe.290.gde-e-165 complete all as specified and directed. 34 e/m works 35 s & fjunction boxes madeup of crca sheet 2 mm thick of the 300 mm x 300 mm x 150 mm complete all as specified and directed. 36 s & f rigid non-metallic pvc conduit 20 mm dia exclusive of boxes (junction/ terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc complete all as specified and directed. 37 s & f for galvanised of 50 mm bore tubes, light grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Central Government/Public Sector

TRN :49055340 | 31 May, 2025

Tender Value : 49.00 Lacs

Pune - Maharashtra

Tender for tender for welcome maint to offrs md accn under age br-i of ge (south) pune; 1 m&l for preparation of old decorative surfaces of ceiling including cornices (plastered or un-plastered) by brooming down and scrapping wherever necessary and applying one coat of white wash complete all as specified and directed 2 m&l for preparation of old decorative surfaces of wall including, cornices (plastered or unplastered)of any description, sand papered and dusted and applying one coat of oil bound distemper of any tint complete all as specified and directed. 3 m&l for preparation of old decorative surfaces of wall including, cornices (plastered or unplastered)of any description, sand papered , and dusted including complete removal of existing surface of walland applying two coats of oil bound distemper over and including a coat of 2mm thick wall care putty complete all as specified and directed 4 m&l for preparation of old painted wooden surfaces exc. 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed 5 m&l for preparation of old painted steel surfaces exc. 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed 6 m & l for preparation of surface of any description (plastered and old decorated) over 10 cm width or girth including removing of existing treatment completely and applying two coats of weather proof exterior paint complete all as specified and directed 7 m&l for preparation of old painted surfaces of walls by brooming down or steel wire brushing , scraping down soot, moulds, moss and efflorescent salt etc surface of any description (plastered and old decorated) over 10 cm width or girth and applying one coatof weather proof exterior paint complete all as specified and directed 8 m & l for preparation of surface of any description (plastered and old decorated) over 10 cm width or girth and applying one coat of luster paint complete all as specified and directed 9 m & l for french polishing on surfaces of any description, exceeding 10 cm width or girth over and including a coat of a coat of wood filler including cleaning and preparation of old wooden surfaces complete all as specified and directed 10 m & l for applying two coatsof oil bound distemper on walls over and including a coat ofpriming with chalk whitening including preparation of new plaster surfaces complete all as specified and directed 11 m&l for applying three coats of white washon ceiling and including preparation of new plaster surface complete all as specified and directed 12 m&l for applying two coats of cement base paintover and including a coat of alkali resistant primer on walls including preparation of new plaster surfaces complete all as specified and directed 13 m & l for preparation of brooming down or steel wire brushing, scraping down soot, moulds, moss and efflorescent salt etc and applying one coat of cement base paint over and including a coat ofalkali resistant primer on walls including preparation of oldsurfaces complete all as specified and directed 14 taking down cement plaster from old brick / stone masonry walls etc. including racking out joints, hacking for keys and scrubbing down with water complete all as specified and directed. 15 m&l for 15 mm thick plaster in cm 1:3 on concrete surfaces finished even and smooth using sagol finish on ceiling complete all as specified and directed 16 demolition of brickwork masonry, built in cement mortar including all quoins, arches, pillars, etc. complete all as specified and directed. 17 m&l for old sizefly ash bricks, straight or curved on plan exc. 6 m mean radiusbuilt in cm 1:6 complete all as specified and directed 18 m&l for brickwork with fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in cm 1:4 complete all as specified and directed 19 m&l for rendering 20 mm thick plaster in two layers on stone masonry surfaces or on other than fair faces of brick / pcc block masonry of walls (first layer 10 mm thick in cement mortar 1:6 and second layer 10mm thick in cm 1:6) and finishing the surface even and smooth without using extra cement complete all as specified and directed. 20 m&l for rendering 20 mm thick plaster in two layers on stone masonry surfaces or on other than fair faces of brick / pcc block masonry of walls (first layer 10 mm thick in cement mortar 1:6 and second layer 10mm thick in cm 1:4 mixed with wpc as per manufacturer’s instructions) and finishing the surface even and smooth without using extra cement complete all as specified and directed.note :- wpc shall be measured and paid separately as supply only under respective item of boq. 21 m&l for rendering 15 mm thick on fair faces of brick work / concrete surfaces in cement mortar 1:4mixed with water proofing compound as per manufacturer’s instructions, finished even and smooth without using extra cement complete all as specified and directed.note :- wpc shall be measured and paid separately as supply only under respective item of boq. 22 m&l for rendering 15 mm thick on fair faces of brick work in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed 23 m&l for pcc 1:3:6 type c-1, (using 20mm graded stone aggregate) of75mm thick, laid in alternate bays as in path and plinth protection including finishing the surfaces even andsmooth using extra cement, complete all as specified and directed 24 s&f in repairs pvc connection 60cm long 15mm dia with 2 nos. pvc nuts repairs complete all as specified and directed. 25 demolition of cement concrete in ground floor and pavings n. exc. 15 cm thickness (below or above gl), complete all as specified and directed. 26 demolition cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed. 27 m&l glazed coloured digital printed ceramic tiles of size 600x300x7-8mm thick in vertical surfaces etc set and jointed in neat cement slurry and pointed in coloured cement to match with colour tiles with and including 15mm thick backing coat in cm 1:4 including triangular filleting in cm 1:4 on top edges including dismantling of old unserviceable tiles including backing coat of any description and removal of debries & dismantled materials complete all as specified and directed 28 m & lfor water proofing treatment to sunken slab, walls,etc. shall be carried out as specified below and as directed by engineer-in-charge:-(a) dismantling & remove the existing lean concrete completely and clean the sunken portion of toilet / baths / wcs / kitchen thoroughly remove laitance, dirt, dust etc.(b) form angle fillet of size 40 mm x 40 mm along the junction of wall and floor by using polymer modified mortar (“ dr fixit” pidicrete urp” or equivalent).(c) sanitary pipes entering through walls and floor shall be sealed with “dr fixit bathseal tape” and the gaps to be grouted with non-shrink cementitous grout “dr fixit bathseal grout” or equivalent. nahani traps etc to be fitted securely and the gaps around it to be grouted in the same manner.(d) apply one coat of a bitumen-modified polymer coating “dr fixit bathseal plus” or equivalent on all angle fillets by brush and cover it with 100mm open woven mesh when it is still wet and applying second coat of the same coating on the angle fillets and allow it to dry completely. contd...... 29 (e) in the remaining area, in dry substrate condition brush apply first coat of the same coating and further apply second coat when first is dry. extend the coating upto150mm above the ffi. above ffi, another cementitious waterproofing waterproof coating “dr fixit pidifin 2 k” or equivalent to be further applied right upto 2.1 m to waterproof the shower area also, if it is a bathroom or bath cubicles of a sanitary annex and apply second coat after 6-8 hoours and allow to dry completely.(f) after 2 to 3 days, sunken portion must be overlaid with a 50 mm thick concrete screed m 15 type b0 mixed with integral wpc (liquid) laid to stope 1:60 towards outer face of wall. provide 40 mm od upvc pipe at the lowest point with 300 mm projection beyond the outer face of the wall. then fill up the sunken portion with lean concrete 1:5:10 type e2.(g) after completing plumbing work in the toilet/wc/bath/kitchen, floor, tiling work (floor and dado) to be carried out by using suitable tile adhesives and ready to make tile grouts of approved makes such as dr fixit, fosroc sika, mc buchemie, roff, etc. note: lean concrete 1:5:10 type e-2 shall be measured and paid separately under respective item of boq. 30 m&l for pcc 1:5:10 type e-2 using 40 mm graded brick aggregate as in filling sunken portion, complete all as specified and directed. 31 m&l for 25 mm thick pcc 1:2:4 type b-1 (using 20mm graded stone aggregate) as in leveling course or pcc padding, finished the surfaces fair & even, complete all as specified and directed. 32 m&l for cleaning and removing all scale and dirt, etc, from tanks n. exc. 500 ltrcapacity and from mouths of circulating pipes etc including writing of date of cleaning with synthetic enamel paint complete all as specified and directed. 33 m&l for cleaning and removing all scale and dirt, etc, from tanks exc. 500 ltrs but n. exc. 1000 ltrcapacity and from mouths of circulating pipes etc including writing of date of cleaning with synthetic enamel paint complete all as specified and directed. 34 m&l for cleaning and removing all scale and dirt, etc, from tanks exc. 1000 ltrs but n. exc. 2000 ltrcapacity and from mouths of circulating pipes etc including writing of date of cleaning with synthetic enamel paint complete all as specified and directed. 35 m&l for granite (of any type) work (table rubbed and polished) 18-20mm thick as in steps, jambs, pillars, window- cills,cookingplatforms, as counters of any radiuos and like setting in neat cement slurry including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, laid over and including 20mm thick screed / backing coat in cement mortar (1:4)including dismantling of old unserviceable slab / tiles including screed bed of any description and removal of debries & dismantled materials complete all as specified and directed 36 rounding (half) of edges of granite stone slabs , as in steps, cooking plateform slab and other similar situations complete all as specified and directed. 37 s&f in repair cascade type (coloured) floor mounted single piecewater closet withpp soft close slim seat cover , hinges, dual flush cistern fittings, fixing accessories and accessories set , size 365 x 675 x740 mm, strap -220 mm pipe etcconnected to pipe complete all as specified and directed by engr in charge confirming to cat no. esc-wht-851s220sppsm essco (jaquar)or of equivalent make as specified here-in-after complete all as specified and directed 38 s&f in repairs glass coner assembly cosisting of 5.5 mm thicksheet glassround(9 x 9 ) with satinless steel railing, complete all as specified and directed 39 s&f inrepairs satinless steel robe hook (khuti) with5hook, complete all as specified and directed 40 s&f in repairs sink cock with swinging casted spout with aerator(wall mounted model) conforming to cat no. orb-105347 essco (jaquar) or of equivalent cat part of makes as specified here-in-after, complete all as specified and directed 41 s&f cp towel ring round with round flange conforming to cat no acn-1121 bn of jaquar / 9218 of prayag or equivalent cat part from the makes as specified here in after, complete all as specified and directed. 42 s&f in repairs brass chromium plated shower rose 100 dia with 235 mm long arm with or without swivel joints, including fixing to steel pipe or union, complete all as specified and directed 43 s&f in repairs brasscp wall mixer3- in-1 system with provn for both hand shower and overhead shower complete with 115 mm long bend pipe connecting legs and wall flange (without hand & ovwer shower ) conforming to cat no.ste-107281 stellaessco (jaquar) or equivalent cat part from the makes as specified here in after, complete all as specified and directed. 44 s&f in repairs cp 15 mm fancy long body bib taps brasswith wall falnge & aeratorconforming to cat no. sqt- 512kn essco ( jaquar) or equivalent cat part from the makes as specified here in after, complete all as specified and directed. 45 s&f in repairs soap dish cat no. acn-1131n jaquar / ba-259 of prayag or of equivalent cat part of makes as specified here-in-after, complete all as specified and directed 46 s&f in repairs cp toilet paper holder conforming to cat no. acn-1151 n of jaquar / ba-38 of prayag or of equivalent cat part of makes as specified here-in-after, complete all as specified and directed 47 s&f in repairs cp towel rail 20mm dia and600mm long including brackets conforming to cat no. acn-111n of jaquar/ ba-20 of prayag or of equivalent cat part of makes as specified here-in-after, complete all as specified and directed 48 s&f in repairs health faucet cat no. ald-583kn of jaquar/ bea-85 of prayag or of equivalent cat part of makes as specified here-in-after, complete all as specified and directed 49 s&f in repairs angular type stop cock with flangeconforming to cat no.apr -101053 essco of (jaquar) or equivalent cat part from the makes as specified here in after, complete all as specified and directed. 50 s&f in repairs cp 2 way bib cock with wall flange conforming to cat no. ste-107041,essco ( jaquar) , cera orequivalent cat part of makes as specified here-in-after, complete all as specified and directed 51 s&f in repairs cp pillartaps swan longneckwith aerator15mm bore fancy type with wall flange conforming to cat no orb -105001n essco ( jaquar) or of equivalent cat part of makes as specified here-in-after, complete all as specified and directed 52 s&f in repairs stainless steel towel rack with lower hangers, 600mm long conforming to cat no. can-1181fhs of jaquar or of equivalent cat part of makes as specified here-in-after, complete all as specified and directed 53 taking up or down steel water tubing and connections including cleaning for refixing or removal to store complete all as specified and directed for following size of pipe :-(a). 15mm bore. 54 (b). 20mm bore. 55 s&f of following dia gi pipe, medium grade including with all fitting & fixtures, fixed on walls and ceilings or laid in floors etccomplete all as specified and directed.(a). 15mm bore 56 (b). 20mm bore. 57 re-fixing only following dia gi pipe, medium grade including with all fitting & fixtures, fixed on walls and ceilings or laid in floors etccomplete all as specified and directed.(a). 15mm bore 58 (b). 20mm bore. 59 m&l for cutting chases, pinning in, concrete, block /brick or stone walling & making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc. and cutting chases for concealed water tubing and making good, cutting n. exc. 10 cm girth, complete all as specified and directed. 60 s&f pvc (swr) 110mm bore pipes, single socketed in any length with rubber ring joints laid in trenches or fixed to wall including dismantling of old unserviceable breaking up drain pipes pvc or ac set in cm or solvent,complete all as specified and directed.note for item nos. 55 & 56:- rate quoted shall deemed to be inclusive of necessary scaffolding / security measures as the work is to be carried out for elevated height upto 12 mtr height building. 61 s&f pvc (swr) 75mm bore pipes, single socketed in any length with rubber ring joints laid in trenches or fixed to wall including dismantling of old unserviceable breaking up drain pipes pvc or ac set in cm or solvent,complete all as specified and directed. 62 s&f pvc (swr) bends any radius 110 mm bore complete all as specified and directed. 63 s&f pvc (swr) bends any radius 75 mm bore complete all as specified and directed. 64 s&f pvc (swr) vent cowl 110mm bore, complete all as specified & directed. 65 s&f in repairs pvc (swr) branch piece, (double y) equal or unequal of 110 mm bore, complete all as specified and directed 66 s&f in repairs pvc (swr) branch piece, (double y) equal or unequal of 75mm bore, complete all as specified and directed 67 s & f 110mm pvc (swr) wc connector bent type complete all as specified and directed. 68 s&f pvc (swr), 75mm dia outlet floor trap, plain with grating including jointing with solvent cement, fixed to cement concrete type b1 1:2:4, complete all as specified and directed. 69 s&f pvc (swr), 75mm dia outlet multi floor trap, plain with grating including jointing with solvent cement, fixed to cement concrete type b1 1:2:4, complete all as specified and directed. 70 m&l for cutting, screwing & threading of existing 15mm bore steel tubing for alterations or additions (each cut measured) complete all as specified and directed 71 m&l for cutting, screwing & threading of existing 20mm bore steel tubing for alterations or additions (each cut measured) complete all as specified and directed 72 m&l for cutting, screwing & threading of existing 25/32mm bore steel tubing for alterations or additions (each cut measured) complete all as specified and directed 73 taking down chowkhat or frames n. exc. 1.5 sqm each with shutter without taking off shutter from the frame complete all as specified and directed. 74 taking down chowkhat or frames exc. 1.5 sqm but n. exc. 4 sqm each with shutter without taking off shutter from the frame complete all as specified and directed. 75 taking down shutters of any description exc. 1 sqm and not exc. 2 sqm each and remove from site, complete all as specified and directed. 76 s&f in repairs vitreous china, squatting pan, orissa pattern, size 580 x 440 mm white, with integral foot rest, including concrete bedding and pvc flushing cistern 10 ltr capacity including all internal fitting, inlet, outlet pipe connections etc. complete all as specified and directed. 77 s & f in repairs, vitreous china wash basin, white, flat back, size 550 x 400 mm with brackets, inc. cutting for & pinning in ends of brackets, including32 mm dia brass cpwastecouplingand32 mmdia low density polyethylene(ldpe) pressure rating 6 kg / cm² as waste pipe complete all as specified and directed 78 s&f in repairs vitreous china wash down water closet pan, pedestal white, including fixing bolts etc including pvc seat cover white with flat bottom including ms, cp or aluminium anodised hinge devices including pvc low level flushing cistern 10 ltr capacity with all internal fitting, inlet, outlet pipe connections etc. complete all as specified and directed. 79 s&f in repairs ewc seat cover of any pattern including cover and mild steel chromium plated hinging devices of any colour, complete all as specified and directed. 80 s&f in repairs, stainless steel plate rack of size 36 inch x 30 inch x 10inch, made out of 0.63mm thick stainless steel sheet (grade 304), s s screws and round pipe,fixed to wall with screws complete all as specified and as directed 81 s&f in repairs flexible waste pipe of 32 mm dia suitable for wash hand basins, sink etc of suitable length, complete all as specified and directed 82 s & f in repairs spindles of any size suitable for concealed mixer valves, stop valves, angle cock, fancy taps including knob heads complete all as directed by engineer-in-charge. 83 s & f in repairs kitchen or laboratory sinks made of stainless steel 1mm thick sheet with plugs, washers, and wastes coupling, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, bowl size 560x460mm including coupling etc complete all as directed by engineer-in-charge. 84 s&f in repair high density 40mm bore polyethylene pipes (hdpe) of pressure rating 6 kg/cm2 fixed to wall or in floors with necessary socket, elbow & bendetc complete fixedto wall or in floors etc complete all as specified and directed. 85 s&fin repair pvc low level flushing cistern 10 ltrs capacity with and including all internal fitting, pair of bracket, including inlet / outlet pvc pipe connections etc. complete all as specified and directed 86 m&l for joint free non-skid ceramic coloured tiles 7 to 8 mm thick area of each tiles exceeding 0.11 sqm but not exceeding 0.18 as in floors, set an jointed in neat cement slurry and pointed in white or coloured cement to match including laid over and including 20 mm thick screed bed in cm 1:6 including taking of old existing unserviceable tiles of any type including screed bed and removing of debries & dismantled materials etc. complete all as specified and as directed 87 m&l for coloured vitrified ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.16 sqm but not exceeding 0.36 sqm as in flooring, set and jointed in neat cement slurry & pointed in white or coloured cement to match laid over and including 20mm thick screed bed in cm 1:6 with including taking of old existing unserviceable tiles of any type including screed bed and removing of debries & dismantled materials etc. complete all as specified and as directed 88 s&f in repairs 20mm dia aluminium powder coated, fancy type curtain rod medium grade fixed in and including bracket, stops roller etc complete all as specified and directed 89 s&f stainless steelfency type caps / side bulbs etc. suitable for 20mm dia curtain rod pipe complete all as specified and directed. 90 s & f pressed steel frames for doors with one & more rebates including necessary fixing lugs, hinges, lock strike plate etc complete as specified size of frame 125 x 60mm including ms hold fast - 6 nos. and ms cold rolled 100mm size butt hinges welding to existing ms frame including pcc bed block in 1:2:4 type b1 for hold fast and cement concrete 1:3:6 type c1 (12.5mm graded stone aggregate) for filling in ms hollow frame complete all as specified and directed. 91 s & f pressed steel frames for doors with one & more rebates including necessary fixing lugs, hinges, lock strike plate etc complete as specified size of frame 125 x 60mm including ms hold fast - 3 nos. and ms cold rolled 100mm size butt hinges welding to existing ms frame including pcc bed block in 1:2:4 type b1 for hold fast and cement concrete 1:3:6 type c1 (12.5mm graded stone aggregate) for filling in ms hollow frame complete all as specified and directed. 92 s&f pvc door frame of size 50mm x 47 mm made out of 5mm plain colour pvc sheet reinforced with ms square tube, suppling & fixing in opening as per specification and drawing. 93 supply and fixing factory made solid pvc shutters,30 mm thick (style) consisting of frame made out of ms tube for top and bottom rails. ms frame shall be covered with heat moulded plain colour pvc c channel having a pvc sheet strips of 20mm width stuck inside with solvent cement for stiles and plain cover pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail; panneling of plain colour pvc sheet to be fitted in the ms frame welded / sealed to the stiles & rail with suitable pvc sheet beading, and joined together with solvent cement, supply and fixing in the frame at site as per specification and drawing. 94 s&f 300 mm long aluminium alloy, anodised , sliding door bolt with hasp staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast- aluminium alloy fixed complete all as specified and directed. 95 s&f 200 mm long aluminium, anodised, barrel tower bolts of extruded section isi marked complete all as specified anddirected. 96 s&f 100mm size extruded aluminium anodised alloy handles, fabricated type, isi marked complete all as specified anddirected. 97 s&f pvc (swr) gully trap 125x110mm, setting and jointing with solvent cement, complete all as specified and directed. 98 s&f 100 mm long butt hinge, alum electroplated, heavy weight, cold rolled mild steel and fixed complete all as specified and directed. 99 s&f in repairs 600 x 450mm beveled edge lookingmirror of selected quality glass, mounted on 6 mm thick ac built board or commercial ply board and fixed to wooden plug with chromium plated brass screws and cup washer etc. complete all as specified and as directed 100 s&f aluminium powder coatedthree track sliding window with two or more shutters with & including 4mm thick tinted glass, one shutter of stainless steel wire cloth 0.36 mm nominal dia & 1.18 mm width aperture for mosquito proofing with good quality bearing, handle, lock etc using pvc beadingetc using following sections of `jindal aluminum ltd or equivalent in ajit india pvt ltd or crystal bombay, as approved fixing to stone masonry walls with & including ist class teak wood plugs of size 20mmx20mm at an interval of 0.5m around the track including drilling holes etc complete all as specified and directed:(a) frame bottom20620(b) frame top& side 20681(c) shutters top & bottom 20844(d) shutter inter lock 20724(e) handle (side) for 20606 shutters 101 s&f ventiltors / louvers with partially guaged shutter using 5 mm thick x 10 cm wide frostedglass strips andby using of following aluminium powder coated sections conforming to catalogue of jindal or of equivalent make including with rubber beading etc, complete all as directed by engr-in-charge.(a) sp20048(b) glazing clips19352 102 s & f150 mm length floor door stopper of brassbody and tongue, hard drawn steel spring complete all as specified and directed. 103 s&f of 18/19 mm thick block board, grade i quality exterior grade type with decorative face veneer on both faces including lapping of edges fixed with screws to timber frame work as in cb partition and shelf and other works complete including dismantling of old unserviceable boards of any type complete all as specified and directed 104 s&f continuous (piano) hinges, mild steel, bright finish, width of flaps (when open) 30mm, complete all as specified and directed. 105 s&f in replacement 100 mm brass fancy type cupboard handle fixed with nuts, screws and washer of brass polished, complete all as specified and directed. 106 s&f in repairs magnet catches and striking plate, complete all as specified and directed 107 removing building materials etc to a distance exceeding 5 km, beyond the lead included in the rates, including loading, unloading and stacking at the destination complete all as specified and as directed. 108 m&l for gypsum ceiling board,pre-painted, perforated finish, 600x600x8 to 9mm thick in size of approved brand / make, laid over and including grid work of size 595 x 595mm, made out of 0.5mm thick g.i. tee 32 x 24 mm for main, 25x24mm for cross tee and 20 x 20mm angle fixed on wall, powder coated finish on exposed faces of tee and angle, hung from ceiling by using 2 mm thick g.i. suspension wires spaced at 1200 mm on main runners including making niches for fans & light , complete all as specified and directed 109 all as per item no.103 but repair only to the existing false ceilings of any description complete all as directed by engr-in-charge 110 dismantling of wall / ceiling boards including snap grid of any thickness including cover fillets, complete all as specified and directed. 111 s&f 4 mm thick sheet glass, ordinary quality and glazing with oil putty or wooden beadings in square n. exc 0.5 sqm in each pane, including hacking out old broken glass if any (any thickness, quality & size), complete all as specified and directed. 112 m&l for machine cut cudappah stone slab one side pre-polished, 30-40mm thick as in kitchen platform base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing laid over and including 15 mm thick screed bedding layer in cm 1:4 including dismantling of old unserviceable slab / tiles including screed bed of any description and removal of debries & dismantled materials complete all as specified and directed 113 s&f of 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sideincluding 5mm thick,1st class hw (tw) beading all around on edging andcomplete all as specified and directed by engr-in-charge 114 m&l for 35mm thick iind class hard wood glazed and skeleton shutters, openrebated and prepare to receive glass (with sash bars), guage etc divided into squares with plain, chamfered or rounded, mitered and rebated sash bars any number, size of members of shutters as specifie in clause 8.24(a) of ssr part-i 2009, complete all as specified and directed. 115 m&l for applying two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces of any description exc. 10 cm width or girth, including preparation of surfaces, complete al as specified and directed. 116 m&l for applying two coats of synthetic enamel paint over acoat of red oxide primer on new steel surfaces exc. 10 cm width or girth, including preparation of surfaces, complete al as specified and directed. 117 m&l for 2nd class hard wood wrought plain fillets square, rectangular or triangular in section clean sawn secured with screws, sectional area exc. 13 sqcm but n. exc. 25 sqcm etc complete including dismantling of timber fillets from cabinet / cupboard frame, complete all as specified and directed 118 s & f in repairs gun metal, globe gate valves(class i), with iron wheel head,screwed both ends for iron pipe, isi marked, all as specified and directed for the following bore dia of pipe:-(a) 15mm bore. 119 (b) 20mm bore. 120 (c) 25mm bore. 121 s&f 25/32mm bore ball valve high pressure of ptmt with epoxy coatedaluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 455 gms), complete all as specified and directed. 122 s&f 20mm bore ball valve high pressure of ptmt with epoxy coatedaluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 210 gms), complete all as specified and directed. 123 s&f 15mm bore ball valve high pressure of ptmt with epoxy coatedaluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 142 gms), complete all as specified and directed. 124 supply only liquid water proofing compound, complete all as specified and directed. 125 s&f in repair for stainless steel wire cloth 0.36nominal dia of wire and average width of aperture 1.4mm and fixedwith stainless steel staple to wooden / steel frames, complete all as specified and directed

Government Departments

TRN :49055388 | 21 May, 2025

Tender Value : 8.06 Lacs

Agra - Uttar Pradesh

Tender for tender for zone-1, ward no.-92, rawatpara roshan mohalla, work of preparing the floor along with repair of office building. - demolishing r.c.c. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of engineer - in- charge. 2 demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge.15.7.4 in cement mortar 3 cleaning of the site for warkable etc. all complete. (non scheduled) 4 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in :cement mortar 1:4 (1 cement : 4 coarse sand) (dsr 2023 sh-6.4.1 ) 5 brick work 7 cm thick with common burnt clay f.p.s. (non modular) brick of class designation 7.5 in cement mortar 1:3 (1 cement : 3 coarse sand) in superstructure above plinth level and upto floor five level. (dsr 2023 sh-6.8 ) 6 reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills,taircases and spiral stair cases above plinth level up to floor fiveevel, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).(dsr 2023 sh-5.3 ) 7 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. thermo-mechanically treated bars of grade fe-500d or more(dsr 2023 sh-5.22.6) 8 centering and shuttering including strutting, propping etc. and removal of form work for :columns, piers, abutments, pillars, posts and struts(dsr 2023 sh-4.3.3 ) 9 12 mm cement plaster of mix : 1:4(1 cement: 4 fine sand)(dsr 2023 sh-13.1.1 ) 10 structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.(dsr 2023 sh-10.1 ) 11 providing and fixing 12 mm thick panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick.fire retardant plywood conforming to is: 5509(dsr 2023 sh-9.126.2 ) 12 providing and fixing isi marked is:1341 m.s. pressed butt hinges bright finished with necessary screws etc. complete :)75x47x1.70 mm (dsr 2023 sh-9.55.3 ) 13 providing & fixing decorative high pressure laminated sheet of plain / wood grain in gloss/ matt/ suede finish with high density protective surface layer and reverse side ofdhesive bonding quality conforming to is : 2046 type s including cost of adhesive of approved quality. 1.0 mm thick (dsr 2023 sh-9.127.2 ) 14 distempering with 1st quality acrylic distemper (ready mixed) having voc content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour new work (two or more coats) over and including water thinnable priming coat with cement primer having voc content less than 50 gram/litre (dsr 2023 sh-13.41.1 ) 15 painting steel work with deluxe multi surface paint to give an even shade. two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture(dsr 2023 sh-1021sub head : 13 finishing13.48.3 ) 16 providing & fixing white vitreous china water closet squatting pan (indian type) along with “s” or “p” trap including dismantling of old wc seat and “s” or “p” trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of engineer-in charge. long pattern w.c pan of size 580x440 mm (dsr 2023 sh-14.80.1) 17 providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require white vitreous china flat back wash basin size 450x 300 mm with single 15mm c.p. brass(dsr 2023 sh-17.7.7) 18 providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white pvc automatic flushing cistern, with fittings, standard size c.p. brass flush pipe, spreaders with unions and clamps (all in c.p. brass) with waste fitting as per is: 2556, c.i. trap with outlet grating and other couplings in c.p. brass, including painting of fittings and cutting and making good the walls and floors wherever required(dsr 2023 sh-17.5.1 ) 19 providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white p.v.c. automatic flushing cistern, with fittings, standard size g.i./ pvc flush pipe for back and front flush with standard spreader pipes with fittings, g.i clamps and c.p. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required: single squatting plate with 5 litre p.v.c. automatic flushing cistern(dsr 2023 sh-17.6.1 ) 20 providing and laying flamed finish granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the engineer-in-charge :flamed finish granite stone slab jet black, cherry red, elite brown, cat eye or equivalent.(dsr 2023 sh-11.55.1 ) 21 providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to isi : 12701, colour of opaque white or as approved by engineer-in- charge. the rate includes making necessary holes for inlet, outlet & over flow pipes. the base support i/c fittings & fixtures for tank shall be paid separately 22 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized pvc medium well casing (cm) pipe of required dia, conforming to is: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of engineer -in-charge100 mm nominal size dia 23 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized pvc medium well casing (cm) pipe of required dia, conforming to is: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of engineer -in-charge150 mm nominal size dia 24 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply and all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one stepcpvc solvent cement and testing of joints complete as per direction of engineer in charge. internal work - exposed on wall 15 mm nominal dia pipes 25 providing and fixing ptmt bib cock of approved quality and colour.15mm nominal bore, 86 mm long, weighing not less than 88 gms 26 providing and fixing ptmt stop cock of approved quality and colour.15 mm nominal bore, 86 mm long, weighing not less than 88 gms) 27 mirror of superior make glass 60x45 cm 28 providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete size of tile 600x600 mm 29 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer-in-charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 30 supply and fixing of light fitting switch board. (none sheduled) 31 supply and fixing wiring of light point. (none sheduled) 32 s/l/j of 20mm dia pvc cunduct pipe etc. all complete. 33 supply & fixing of wiring sub main. 34 supply & fixing of plug point 15mm. 35 lettering & painting of wall etc. all complete. 36 supply & fixing of 27watt. cfl etc. all complete. 37 carriage of materials by manual labour including loading, unloading and stacking for lead less than 01-50 mtrm.207.34+30.42 every 50 additonal meter 38 constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast r.c.c. horizontal grating with frame complete as per standard design :with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 39 kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick 40 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.) 41 chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : light shade pigment using white cement 42 marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with :raj nagar plain 43 providing and fixing stainless steel ( grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)(dsr 2023 sh-10.28 ) 44 1:2:4 (1 cement : 2 coarse sand (zone-iii) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources). (dsr 2023 s h) 45 supply & fixing granite stone work display board (size 2.50ft x 4.00ft) including painting, lettering etc. all complete. (none schedule) 46 making ornamental painting with special design make by specialist painter laying of two coat birla white putty and design by asian paint including all material etc. all complete. (nn approved) 47 sub total 48 add/deduction rs. for estimate figure amount match 49 grand total

Local Bodies

TRN :49056288 | 14 May, 2025

Tender Value : 0

Agra - Uttar Pradesh

Tender for tender for repair painting and maintenance work of agra development authority premises and all office rooms - 12mm thick cement plaster in single coat on fair side of single or half brick wall for interior plastering upto floor two level including internal rounded angles not exceeding 80mm in girth, chamfers and finished even and smooth. (item no. 13.4.1 dsr-2023) 1 cement : 4 coarse sand 2 removing white or colour wash by scrapping and sand papering and preparing the surfacesmooth including necessary repairs to scratches etc. complete(item no. 13.88 dsr-2023) 3 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. (item no. 13.80 dsr 2023) 4 finishing walls with acrylic smooth exterior paint of required shade : old work (two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface (item no. 13.111.1 dsr 2023) 5 painting with synthetic enamel paint of approved brand and manufacture to give an even shade : 13.61.1 two or more coats on new work (item no. 13.61.1 dsr 2023) 6 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete (item no. 5.22.1, dsr-2023) 7 rcc work providing and laying in position specified grade of reinforced cement concrete,slab including the cost of centering, shutterang, finishing and excluding reinforcement - above plinth level upto fifth floor lable : 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone (item no. 5.1.2 dsr 2023) 8 reinforced cement concrete work in walls (any thickness), including attachedpilasters, buttresses, plinth and string courses, fillets, columns, pillars, plers, abutments, posts and struts etc, including cost of centering, shuttering, finishing and excluding reinforced :- 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size). (item no. 5.2.2 dsr 2023)i) upto plinth level 9 engagement of plumber with kit. 10 engagement of plumber helper. 11 engaging of beldar for malva disposal. (item no. 0114 dsr 2023) 12 engagement of carpenter. (item no. 0111 dsr 2023) 13 providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding grouting the joints with white cement and matching pigments etc., complete. size of tile 600x600 mm (item no. 11.41.2 dsr 2023) 14 providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to is : 15622 of approved make in colours such as white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. (item no. 11.37 dsr 2023) 15 providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws, all complete as per rchitectural drawings and the directions of engineer-in-charge. (glazing, paneling and dash fasteners to be paid for separately)(item no. 21.1.2.2 dsr 2023) powder coated aluminium (minimum thickness of powder coating 50 micron) 16 providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per (cost of aluminium snap beading shall be paid in basic item):(item no. 21.3.2 dsr 2023)with float glass panes of 5 mm thickness 17 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. :(item no. 18.7 dsr 2023) 15 mm nominal outer dia pipes (item no. 18.7.1 dsr 2023) 18 20 mm nominal outer dia pipes (item no. 18.7.2 dsr 2023) 19 25 mm nominal outer dia pipes (item no. 18.7.3 dsr 2023) 20 providing and fixing pvc pipe conforming to is make working pressure 6 kg/sqcm incuding testing labour t&p and all complete fittings (ch-23 s.i. no. 30 sor 2023-24) 21 110 mm diameter 22 140 mm diameter 23 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in foundation and plinth in: cement mortar 1:4 (1 cement : 4 coarse sand) (item no. 6.1.1 dsr 2023) 24 class-150 (non modular) brick work in 1:4 cement and coarse sand mortar in super structure above plinth level upto floor five level including necessary cutting and moulding of brick work as required and also including honey combed brick work in thickness of wall more than 12cm. (item no. 6.4 dsr 2023) 25 steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as requiredin gratings, frames, guard bar, ladder, railings, brackets, gates and similar works (item no. 10.25.2 dsr 2023) 26 providing and fixing stainless steel ( grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). (item no. 10.28 dsr 2023) 27 providing and laying flamed finish granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the engineer-in-charge :flamed finish granite stone slab jet black, cherry red, elite brown, cat eye or equivalent.(item no. 11.55.1 dsr 2023) 28 40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand), including pointing with cement mortar 1:2 (1 cement : 2 stone dust) with an admixture of pigment to match the shade of stone. red sand stone (item no. 11.29.1 dsr 2023) 29 providing and fixing c.p. brass long body bib cock of approved quality conforming to is standards and weighing not less than 690 gms. 15 mm nominal bore (item no. 18.51.1 dsr 2023) 30 providing and fixing c.p. brass angle valve for basin mixer and geyser points of approvedquality conforming to is:8931 (15mm nominal bore). (item no. 18.53.1 dsr 2023) 31 providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white pvc automatic flushing cistern, with fittings, standard size c.p. brass flush pipe, spreaders with unions and clamps (all in c.p. brass) with waste fitting as per is : 2556, c.i. trap with outlet grating and other couplings in c.p. brass, including painting of fittings and cutting and making good the walls and floors wherever required: (item no. 17.5.1 dsr 2023) single half stall urinal with 5 litre pvc. automatic flushing cistern 32 providing and fixing white vitreous china pedestal type water closet (european type w.c. pan) with seat and lid, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: w.c. pan with isi marked white solid plastic seat and lid (item no. 17.2.1 dsr 2023) 33 providing and fixing uplasticised pvc connection pipe with brass unions:(item no. 18.21.2.2 dsr 2023) 45 cm length - 20 mm nominal bore 34 providing and fixing p.v.c. waste pipe for sink or wash basin including pvc waste fittings complete.(item no. 17.28.2.2 dsr 2023) flexible pipe - 40 mm dia 35 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. (35 mm thick including isi marked stainless steel butt hinges with necessary screws) (item no. 9.20.1 dsr 2023) 36 providing and laying six courses water proofing treatment with bitumen felt over roofs consisting of first, third and fifth courses of blown or / and residual bitumen applied hot at 1.45, 1.20 and 1.70 kg per square metre of area respectively, second and fourth courses of roofing felt type 2 grade ii (glass fibre base self finished bitumen felt) and sixth and final course of stone grit 6 mm and down size or pea sized gravel spread at 6 cubic decimeter per sqm including preparation of surface but excluding grading, complete (item no. 22.11 dsr 2023) 37 providing and laying cement concrete in 1:4:8 (1 cement : 4 course sand : 8 graded stone aggregate 40 mm nominal size) and curing complete, including cost of form work in foundation and floors.(item no. 4.1.8 dsr-2023) 38 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-iii) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) (item no. 4.1.3 dsr 2023) 39 providing corrugated g.s. sheet roofing including vertical / curved surface fixed with polymer coated j or l hooks, bolts and nuts 8 mm diameter with bitumen and g.i. limpet washers or with g.i. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. (item no. 12.1.3. dsr 2023) 0.63 mm thick with zinc coating not less than 275 gm/ m² 40 engaging of blacksmith 1st class (item no. 0102 dsr-2023) 41 providing and placing on terrace (at all floor levels) polyethylene water storage tank, is : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. (item no. 18.48 dsr-2023) 42 supplyof stone screening 11.2mm nominal size. (ch-1 item no. 3(d)h sor 2023-24) 43 supply of coarse sand.(ch-1 item no. 6 sor 2023-24)

State Government

TRN :49056708 | 23 May, 2025

Tender Value : 0

Kolkata - West Bengal

Tender for supply, delivery & installation of submersible pumping machinery and other electrical / mechanical equipment etc. including allied works for santoshpur water supply scheme, t.w. no. iv, block: tarakeswar, district - hooghly under electrical division, phe dte.- 1 part-a supply and delivery at site submersible pumping machinery directly coupled with wet winding type submersible motor having the following specification pump.duty condition :36 cu.mtrhead :58 mtr.motor : submersible type 3 ph. 50 hz. 400v + 10%, mos:- star deltaimpeller : gm/ ss/ cromesteelmotor winding : wet type.pump outlet - 65/75/100 mm.(test certificate, warranty certificate along with characteristic curve should be submitted at the time of delivery.) 2 supply and delivery at site the following:-upvc 80 mm dia column pipewith both side square threaded (8 tpi)with one socket and o ring biax technology with wiring lock system non corrosive,high tensile having iso 9001 standard. 3 i)3 mtr. long. 4 ii) 1.5 mtr. long 5 iii) 80 mm dia top & bottom adaptor 6 100 mm x 80 mm dia gi reducer 7 supply and delivery at site heavy type suitable dia m.s. suspension clamp for above column pipe along with nuts, bolts and washers etc. 8 supply and delivery at site 80 mm. dia cidf sluice valve- 1 no., 80mm non return valve (swing type - 1 no.) pn - 1.0,80mm ms heavy flange - 1 no., cidf bend 90o - 1 no., cidf / ms (heavy) short piece as required length, 80mm cidf tee - 1 no., reducer, nut bolt and other ci / ms specials etc. as required as per i.s. specification and other required materials for the job i.e. for making complete construction of delivery and wash out lineas per relavant i.s. (test certificate for valve should be submitted at the time of delivery). 9 supply and delivery at site split type m.s. fabricated suitable tubewell cover for the tubewell housing with necessary clamping arrangement including holes for column pipe, air pipe and cable entry etc. 10 supply and delivery at site depth gauge (make : h. guru) 102 mm dia. with steel airbreak pipe required length with all other fittings and accessories for the work including supplying on the good quality hand pump of approve make 11 supply and delivery at site pressure gauge 102 mm. dia and 7 kg. /cm2 range, brass cocks and fitting complete(h.guru) 12 supply and delivery at site 4 sq. mm. 3 core copper 1.1 kv grade pvc insulated water proof flat submersible cable. 13 making safety device for above pump by supplying 3 nos. suitable size ms clamp/ ms cage and 1 dia nylon rope of required length including supplying nuts, bolts, and other materials as per direction. 14 supply & delivery of double flanged three phase 50 hz quarter turn electrical actuator [gear case lubrication : sp68 is:13095, torch switches: 2 x 1 no / 1 nc changeover contact, positional limit switches: 2 x 1 no / 1 nc changeover contacts] operated flange type butterfly valve (pn - 1.0) 80 mm. dia with mechanical position indicator, ci body & disk - is: 210 gr. fg 260, shaft of stainless steel aisi 410 as per bs 5155 ip - 68 / s-2,(test certificate should be submitted at the time of delivery) 15 supply & delivery of 415 v mcc cum pdb. with minimum 2mm thickness and degree of protection ip - 54, conforming to is-8623 withsuitable bus bar, digital voltmeter ammeter, contactor, delay timer, mcb, valve actuator starter etc. with plc logic & ups as detailed in annexure - i7.5 -12.5 hp with sds (star delta starter)panel make : digitek / rnr industries /pce projects / opg power system / ecs.[tc / gc to be submitted along with panel after approval of detail power and control circuit drawing by eic]. 16 supply & delivery of 35 sq. mm. 3 1/2 core pvc insulatedal. armoured cable (1.1 kv grade), is 1554 (part - i) / is 7098 (part-i) make : incab /gloster / nicco / polycab / crystal. 17 supply & delivery of 100 amp. 440 v, 50 hz. tpn main switch with rewireable type fuse link 18 supply & delivery of 100 amp. industrial copper busbar 19 supply & delivery of 4 pole 100 amp changeover unit 20 supply & delivery of 100 amp 4 pole mccb with adjustable overload and adjacent short circuit protection including enclosures. 21 supply & delivery at site of 25 kva, 3 phase oil cooled type servo motor operated wound line voltage corrector conforming to is-9815 [pt-i] 1994 suitable for unbalanced input voltage.input voltage: 3 phase main supply phase to phase 200v-500v 3 servo motor in 3 phase with all protection by mcb (make- abb / siemens/ l&t)output voltage: 3 phase balanced output phase to phase 415v + 1% (test certificate & warranty certificate should be submitted at the time of delivery) 22 supply and delivery of automatic plunger type chlorinator for feeding accurately automatic controlled dosage of chlorine solution into the water by connecting metering pump with flow rate of water 0-100 ltr/hr. with maximum pressure of 10 kg./cm2 suitable dosing pump and other necessary accessories on the delivery pipe line as required. the pump shall be coupled with 1/2 hp motor having 3 phase power and 1440 rpm (+4%).(test certificate will be submitted at the time of delivery) 23 part-binstallation of pumping machinery with valves, pipe & pipe specials, sort piece, presurre gauge including hoisting of column pipe making all electrical and water line interconnection complete as per direction including supply of necessary materials as required for the work. 24 making of tubewell foundation (size- 3x 3x 3.5 approx) as per site situation including supply of necessary materials as bricks, sand, cement, stone chips etc. with plastering & neat cement finishing to complete as per direction. 25 installtion of panel & actuator operated ci butterfly valvewith supply of 12 core 2.5 sq. mm. copper control cable, compensating ms flange, nuts, bolts gasket and other fixing materials as required to complete the job including necessary making of brick pillar as per site situation with supply of necessary materials like bricks, sand, cement, stone chips etc. with plastering & neat cement finishing in all respect including successfull operation along with testing of the whole installation as per entire satisfaction of eic. 26 installation with testing and commissioning of the voltage stabilizer with necessary foundation along with necessary accessories in the suitable position and drawing cable with ms shaddle, making all electrical connection including socketing, crimping to complete the work as per direction. 27 installation of above supplied chlorinator pump set and drawing of power line by supplying of necessary wire and continuous earthing connected to auto/ manual panel. this includes the cost of making necessary brick foundation base with neat cement finish by supplying all requered materials and testing entire set as per direction of eic 28 making internal electrification with 16amp main switch/mcb (make: havells/ any approved) by 1.5 sq.mm frlsh grade copper pvc insulated single core multistrand wire (make: havells/ mescab/ finolex/ any approved) in pvc casing of pump house consisting of 2 nos. bracket point, 1 no. tube light point, 1 no. bulk head point and 1 no. five pin 5 amp. socket point, 1 no. ceiling fan point with controlling switches including supply of 2 nos. bracket with 12w led lamp, 1 no. 20 watt led tube light set, 1 no. outdoor type bulk head with 9w led lamp and drawing of necessary earthing (1.0 sq.mm) material all complete as per direction eic. (led light make: philips/ havells/ any approved) 29 supply and fitting fixing of 45 watt. x 2 nos. led light set [make - philips, model: brp031 led45 cw slr gr psu] with 2 nos 40 mm dia 1.5 mtr. long g.i pipe bracket fixed on the roof of the pump house with properly grout including making power connection by 2 x 1.5 sq. mm copper fr grade flexible wire through pvc casing/conduit with drawing earth conductor (1.0 sq mm copper flexible wire), fitting fixing of 15 amp switch on board with all complete as per direction of eic. 30 earthing confirming to is: 3043 by 50mm dia gi pipe 3.64mm thick x 3.04m long and 1 x 4 swggi (hot dip) wire (4 mts. long), 13mm dia x 80mm long gi bolts, double nuts, double washers including supply & fixing of 15mm dia gi pipe protection (1 mtr long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 mtrs below the ground level and restoring surface duly rammed as below. a) for soft soilby tata - medium gi pipe 31 drawing earth by m.s. flat strip (20mm x 3mm) fromearth bus / electrode to above differentcomponents as per i.e. rules and as per direction of eic. 32 supply & fitting fixing of 100 amp. kit kat (3 nos.)(make : havells) with required size wooden board mounted on wall. 33 supply, delivery & fitting fixing of 48 sweep 230 volt, 50 hz, ac ceiling fan (make : havells/ cg/ approved make) including fitting fixing on ceiling and making electrical connection complete. 34 supply & delivery at site 2 nos. plastic chair & 1 no. plastic table (make: cello / supreme / nilkamal) 35 trial operation and guarding of whole installationas per departmental requirement and guideline 1 no. operator @ 465/- per day with 8.33% bonus. [as per existing departmental terms & conditions] 36 add: 18% gst 37 add: 1% cess

State Government

TRN :49056717 | 23 May, 2025

Tender Value : 0

Kolkata - West Bengal

Tender for supply, delivery & installation of submersible pumping machinery and other electrical / mechanical equipment etc. including allied works for sibaichandi water supply scheme, t.w. no. v & vi, block: dhaniakhali, district - hooghly under electrical division, phe dte.-1 part-a supply and delivery at site submersible pumping machinery directly coupled with wet winding type submersible motor having the following specification pump.duty condition :36 cu.mtrhead :58 mtr.motor : submersible type 3 ph. 50 hz. 400v + 10%, mos:- star deltaimpeller : gm/ ss/ cromesteelmotor winding : wet type.pump outlet - 65/75/100 mm.(test certificate, warranty certificate along with characteristic curve should be submitted at the time of delivery.) 2 supply and delivery at site the following:-upvc 80 mm dia column pipewith both side square threaded (8 tpi)with one socket and o ring biax technology with wiring lock system non corrosive,high tensile having iso 9001 standard. 3 i)3 mtr. long. 4 ii) 1.5 mtr. long 5 iii) 80 mm dia top & bottom adaptor 6 100 mm x 80 mm dia gi reducer 7 supply and delivery at site heavy type suitable dia m.s. suspension clamp for above column pipe along with nuts, bolts and washers etc. 8 supply and delivery at site 80 mm. dia cidf sluice valve- 1 no., 80mm non return valve (swing type - 1 no.) pn - 1.0,80mm ms heavy flange - 1 no., cidf bend 90o - 1 no., cidf / ms (heavy) short piece as required length, 80mm cidf tee - 1 no., reducer, nut bolt and other ci / ms specials etc. as required as per i.s. specification and other required materials for the job i.e. for making complete construction of delivery and wash out lineas per relavant i.s. (test certificate for valve should be submitted at the time of delivery). 9 supply and delivery at site split type m.s. fabricated suitable tubewell cover for the tubewell housing with necessary clamping arrangement including holes for column pipe, air pipe and cable entry etc. 10 supply and delivery at site depth gauge (make : h. guru) 102 mm dia. with steel airbreak pipe required length with all other fittings and accessories for the work including supplying on the good quality hand pump of approve make 11 supply and delivery at site pressure gauge 102 mm. dia and 7 kg. /cm2 range, brass cocks and fitting complete(h.guru) 12 supply and delivery at site 4 sq. mm. 3 core copper 1.1 kv grade pvc insulated water proof flat submersible cable. 13 making safety device for above pump by supplying 3 nos. suitable size ms clamp/ ms cage and 1 dia nylon rope of required length including supplying nuts, bolts, and other materials as per direction. 14 supply & delivery of double flanged three phase 50 hz quarter turn electrical actuator [gear case lubrication : sp68 is:13095, torch switches: 2 x 1 no / 1 nc changeover contact, positional limit switches: 2 x 1 no / 1 nc changeover contacts] operated flange type butterfly valve (pn - 1.0) 80 mm. dia with mechanical position indicator, ci body & disk - is: 210 gr. fg 260, shaft of stainless steel aisi 410 as per bs 5155 ip - 68 / s-2,(test certificate should be submitted at the time of delivery) 15 supply & delivery of 415 v mcc cum pdb. with minimum 2mm thickness and degree of protection ip - 54, conforming to is-8623 withsuitable bus bar, digital voltmeter ammeter, contactor, delay timer, mcb, valve actuator starter etc. with plc logic & ups as detailed in annexure - i7.5 -12.5 hp with sds (star delta starter)panel make : digitek / rnr industries /pce projects / opg power system / ecs.[tc / gc to be submitted along with panel after approval of detail power and control circuit drawing by eic]. 16 supply & delivery of 35 sq. mm. 3 1/2 core pvc insulatedal. armoured cable (1.1 kv grade), is 1554 (part - i) / is 7098 (part-i) make : incab /gloster / nicco / polycab / crystal. 17 supply & delivery of 100 amp. 440 v, 50 hz. tpn main switch with rewireable type fuse link 18 supply & delivery of 100 amp. industrial copper busbar 19 supply & delivery of 4 pole 100 amp changeover unit 20 supply & delivery of 100 amp 4 pole mccb with adjustable overload and adjacent short circuit protection including enclosures. 21 supply & delivery at site of 25 kva, 3 phase oil cooled type servo motor operated wound line voltage corrector conforming to is-9815 [pt-i] 1994 suitable for unbalanced input voltage.input voltage: 3 phase main supply phase to phase 200v-500v 3 servo motor in 3 phase with all protection by mcb (make- abb / siemens/ l&t)output voltage: 3 phase balanced output phase to phase 415v + 1% (test certificate & warranty certificate should be submitted at the time of delivery) 22 supply and delivery of automatic plunger type chlorinator for feeding accurately automatic controlled dosage of chlorine solution into the water by connecting metering pump with flow rate of water 0-100 ltr/hr. with maximum pressure of 10 kg./cm2 suitable dosing pump and other necessary accessories on the delivery pipe line as required. the pump shall be coupled with 1/2 hp motor having 3 phase power and 1440 rpm (+4%).(test certificate will be submitted at the time of delivery) 23 part-binstallation of pumping machinery with valves, pipe & pipe specials, sort piece, presurre gauge including hoisting of column pipe making all electrical and water line interconnection complete as per direction including supply of necessary materials as required for the work. 24 making of tubewell foundation (size- 3x 3x 3.5 approx) as per site situation including supply of necessary materials as bricks, sand, cement, stone chips etc. with plastering & neat cement finishing to complete as per direction. 25 installtion of panel & actuator operated ci butterfly valvewith supply of 12 core 2.5 sq. mm. copper control cable, compensating ms flange, nuts, bolts gasket and other fixing materials as required to complete the job including necessary making of brick pillar as per site situation with supply of necessary materials like bricks, sand, cement, stone chips etc. with plastering & neat cement finishing in all respect including successfull operation along with testing of the whole installation as per entire satisfaction of eic. 26 installation with testing and commissioning of the voltage stabilizer with necessary foundation along with necessary accessories in the suitable position and drawing cable with ms shaddle, making all electrical connection including socketing, crimping to complete the work as per direction. 27 installation of above supplied chlorinator pump set and drawing of power line by supplying of necessary wire and continuous earthing connected to auto/ manual panel. this includes the cost of making necessary brick foundation base with neat cement finish by supplying all requered materials and testing entire set as per direction of eic 28 making internal electrification with 16amp main switch/mcb (make: havells/ any approved) by 1.5 sq.mm frlsh grade copper pvc insulated single core multistrand wire (make: havells/ mescab/ finolex/ any approved) in pvc casing of pump house consisting of 2 nos. bracket point, 1 no. tube light point, 1 no. bulk head point and 1 no. five pin 5 amp. socket point, 1 no. ceiling fan point with controlling switches including supply of 2 nos. bracket with 12w led lamp, 1 no. 20 watt led tube light set, 1 no. outdoor type bulk head with 9w led lamp and drawing of necessary earthing (1.0 sq.mm) material all complete as per direction eic. (led light make: philips/ havells/ any approved) 29 supply and fitting fixing of 45 watt. x 2 nos. led light set [make - philips, model: brp031 led45 cw slr gr psu] with 2 nos 40 mm dia 1.5 mtr. long g.i pipe bracket fixed on the roof of the pump house with properly grout including making power connection by 2 x 1.5 sq. mm copper fr grade flexible wire through pvc casing/conduit with drawing earth conductor (1.0 sq mm copper flexible wire), fitting fixing of 15 amp switch on board with all complete as per direction of eic. 30 earthing confirming to is: 3043 by 50mm dia gi pipe 3.64mm thick x 3.04m long and 1 x 4 swggi (hot dip) wire (4 mts. long), 13mm dia x 80mm long gi bolts, double nuts, double washers including supply & fixing of 15mm dia gi pipe protection (1 mtr long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 mtrs below the ground level and restoring surface duly rammed as below. a) for soft soilby tata - medium gi pipe 31 drawing earth by m.s. flat strip (20mm x 3mm) fromearth bus / electrode to above differentcomponents as per i.e. rules and as per direction of eic. 32 supply & fitting fixing of 100 amp. kit kat (3 nos.)(make : havells) with required size wooden board mounted on wall. 33 supply, delivery & fitting fixing of 48 sweep 230 volt, 50 hz, ac ceiling fan (make : havells/ cg/ approved make) including fitting fixing on ceiling and making electrical connection complete. 34 supply & delivery at site 2 nos. plastic chair & 1 no. plastic table (make: cello / supreme / nilkamal) 35 trial operation and guarding of whole installationas per departmental requirement and guideline 1 no. operator @ 465/- per day with 8.33% bonus. [as per existing departmental terms & conditions]

State Government

TRN :49056725 | 23 May, 2025

Tender Value : 0

Kolkata - West Bengal

Tender for supply, delivery & installation of submersible pumping machinery and other electrical / mechanical equipment etc. including allied works for amodghata water supply scheme, t.w. no. vi, block: chinsura mogra, district - hooghly under electrical division, phe dte.- 1 part-a supply and delivery at site submersible pumping machinery directly coupled with wet winding type submersible motor having the following specification pump.duty condition :36 cu.mtrhead :58 mtr.motor : submersible type 3 ph. 50 hz. 400v + 10%, mos:- star deltaimpeller : gm/ ss/ cromesteelmotor winding : wet type.pump outlet - 65/75/100 mm.(test certificate, warranty certificate along with characteristic curve should be submitted at the time of delivery.) 2 supply and delivery at site the following:-upvc 80 mm dia column pipewith both side square threaded (8 tpi)with one socket and o ring biax technology with wiring lock system non corrosive,high tensile having iso 9001 standard. 3 i)3 mtr. long. 4 ii) 1.5 mtr. long 5 iii) 80 mm dia top & bottom adaptor 6 100 mm x 80 mm dia gi reducer 7 supply and delivery at site heavy type suitable dia m.s. suspension clamp for above column pipe along with nuts, bolts and washers etc. 8 supply and delivery at site 80 mm. dia cidf sluice valve- 1 no., 80mm non return valve (swing type - 1 no.) pn - 1.0,80mm ms heavy flange - 1 no., cidf bend 90o - 1 no., cidf / ms (heavy) short piece as required length, 80mm cidf tee - 1 no., reducer, nut bolt and other ci / ms specials etc. as required as per i.s. specification and other required materials for the job i.e. for making complete construction of delivery and wash out lineas per relavant i.s. (test certificate for valve should be submitted at the time of delivery). 9 supply and delivery at site split type m.s. fabricated suitable tubewell cover for the tubewell housing with necessary clamping arrangement including holes for column pipe, air pipe and cable entry etc. 10 supply and delivery at site depth gauge (make : h. guru) 102 mm dia. with steel airbreak pipe required length with all other fittings and accessories for the work including supplying on the good quality hand pump of approve make 11 supply and delivery at site pressure gauge 102 mm. dia and 7 kg. /cm2 range, brass cocks and fitting complete(h.guru) 12 supply and delivery at site 4 sq. mm. 3 core copper 1.1 kv grade pvc insulated water proof flat submersible cable. 13 making safety device for above pump by supplying 3 nos. suitable size ms clamp/ ms cage and 1 dia nylon rope of required length including supplying nuts, bolts, and other materials as per direction. 14 supply & delivery of double flanged three phase 50 hz quarter turn electrical actuator [gear case lubrication : sp68 is:13095, torch switches: 2 x 1 no / 1 nc changeover contact, positional limit switches: 2 x 1 no / 1 nc changeover contacts] operated flange type butterfly valve (pn - 1.0) 80 mm. dia with mechanical position indicator, ci body & disk - is: 210 gr. fg 260, shaft of stainless steel aisi 410 as per bs 5155 ip - 68 / s-2,(test certificate should be submitted at the time of delivery) 15 supply & delivery of 415 v mcc cum pdb. with minimum 2mm thickness and degree of protection ip - 54, conforming to is-8623 withsuitable bus bar, digital voltmeter ammeter, contactor, delay timer, mcb, valve actuator starter etc. with plc logic & ups as detailed in annexure - i7.5 -12.5 hp with sds (star delta starter)panel make : digitek / rnr industries /pce projects / opg power system / ecs.[tc / gc to be submitted along with panel after approval of detail power and control circuit drawing by eic]. 16 supply & delivery of 35 sq. mm. 3 1/2 core pvc insulatedal. armoured cable (1.1 kv grade), is 1554 (part - i) / is 7098 (part-i) make : incab /gloster / nicco / polycab / crystal. 17 supply & delivery of 100 amp. 440 v, 50 hz. tpn main switch with rewireable type fuse link 18 supply & delivery of 100 amp. industrial copper busbar 19 supply & delivery of 4 pole 100 amp changeover unit 20 supply & delivery of 100 amp 4 pole mccb with adjustable overload and adjacent short circuit protection including enclosures. 21 supply & delivery at site of 25 kva, 3 phase oil cooled type servo motor operated wound line voltage corrector conforming to is-9815 [pt-i] 1994 suitable for unbalanced input voltage.input voltage: 3 phase main supply phase to phase 200v-500v 3 servo motor in 3 phase with all protection by mcb (make- abb / siemens/ l&t)output voltage: 3 phase balanced output phase to phase 415v + 1% (test certificate & warranty certificate should be submitted at the time of delivery) 22 supply and delivery of automatic plunger type chlorinator for feeding accurately automatic controlled dosage of chlorine solution into the water by connecting metering pump with flow rate of water 0-100 ltr/hr. with maximum pressure of 10 kg./cm2 suitable dosing pump and other necessary accessories on the delivery pipe line as required. the pump shall be coupled with 1/2 hp motor having 3 phase power and 1440 rpm (+4%).(test certificate will be submitted at the time of delivery) 23 part-binstallation of pumping machinery with valves, pipe & pipe specials, sort piece, presurre gauge including hoisting of column pipe making all electrical and water line interconnection complete as per direction including supply of necessary materials as required for the work. 24 making of tubewell foundation (size- 3x 3x 3.5 approx) as per site situation including supply of necessary materials as bricks, sand, cement, stone chips etc. with plastering & neat cement finishing to complete as per direction. 25 installtion of panel & actuator operated ci butterfly valvewith supply of 12 core 2.5 sq. mm. copper control cable, compensating ms flange, nuts, bolts gasket and other fixing materials as required to complete the job including necessary making of brick pillar as per site situation with supply of necessary materials like bricks, sand, cement, stone chips etc. with plastering & neat cement finishing in all respect including successfull operation along with testing of the whole installation as per entire satisfaction of eic. 26 installation with testing and commissioning of the voltage stabilizer with necessary foundation along with necessary accessories in the suitable position and drawing cable with ms shaddle, making all electrical connection including socketing, crimping to complete the work as per direction. 27 installation of above supplied chlorinator pump set and drawing of power line by supplying of necessary wire and continuous earthing connected to auto/ manual panel. this includes the cost of making necessary brick foundation base with neat cement finish by supplying all requered materials and testing entire set as per direction of eic 28 making internal electrification with 16amp main switch/mcb (make: havells/ any approved) by 1.5 sq.mm frlsh grade copper pvc insulated single core multistrand wire (make: havells/ mescab/ finolex/ any approved) in pvc casing of pump house consisting of 2 nos. bracket point, 1 no. tube light point, 1 no. bulk head point and 1 no. five pin 5 amp. socket point, 1 no. ceiling fan point with controlling switches including supply of 2 nos. bracket with 12w led lamp, 1 no. 20 watt led tube light set, 1 no. outdoor type bulk head with 9w led lamp and drawing of necessary earthing (1.0 sq.mm) material all complete as per direction eic. (led light make: philips/ havells/ any approved) 29 supply and fitting fixing of 45 watt. x 2 nos. led light set [make - philips, model: brp031 led45 cw slr gr psu] with 2 nos 40 mm dia 1.5 mtr. long g.i pipe bracket fixed on the roof of the pump house with properly grout including making power connection by 2 x 1.5 sq. mm copper fr grade flexible wire through pvc casing/conduit with drawing earth conductor (1.0 sq mm copper flexible wire), fitting fixing of 15 amp switch on board with all complete as per direction of eic. 30 earthing confirming to is: 3043 by 50mm dia gi pipe 3.64mm thick x 3.04m long and 1 x 4 swggi (hot dip) wire (4 mts. long), 13mm dia x 80mm long gi bolts, double nuts, double washers including supply & fixing of 15mm dia gi pipe protection (1 mtr long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 mtrs below the ground level and restoring surface duly rammed as below. a) for soft soilby tata - medium gi pipe 31 drawing earth by m.s. flat strip (20mm x 3mm) fromearth bus / electrode to above differentcomponents as per i.e. rules and as per direction of eic. 32 supply & fitting fixing of 100 amp. kit kat (3 nos.)(make : havells) with required size wooden board mounted on wall. 33 supply, delivery & fitting fixing of 48 sweep 230 volt, 50 hz, ac ceiling fan (make : havells/ cg/ approved make) including fitting fixing on ceiling and making electrical connection complete. 34 supply & delivery at site 2 nos. plastic chair & 1 no. plastic table (make: cello / supreme / nilkamal) 35 trial operation and guarding of whole installationas per departmental requirement and guideline 1 no. operator @ 465/- per day with 8.33% bonus. [as per existing departmental terms & conditions] 36 add: 18% gst 37 add: 1% cess

corporations/Associations/Others

TRN :49056804 | 23 May, 2025

Tender Value : 18.27 Lacs

Prayagraj - Uttar Pradesh

Tender for tender for annual civil & electrical m&r work for residential building situated at 20-clive road hydel colony, prayagraj - earth work in excavation by mechanical means (hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. for all kinds of soil. 2 supplying and filling in plinth withsand under floors, including watering, ramming, consolidating and dressing complete. 3 surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. for all kinds of soil. 4 excavating, supplying, stacking and filling of local earth by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift. 5 providing and laying in position cement concrete of grade 1:1½:3 (1 cement: 1½ coarse sand (zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) excluding the cost of centering and shuttering - all work up to plinth level : 6 providing and laying in position cement concrete of grade1:2:4 (1 cement : 2 coarse sand (zone-iii) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) excluding the cost of centering and shuttering - all work up to plinth level : 7 providing and laying in position cement concrete of grade 1:5:10 (1 cement : 5 fine sand derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) excluding the cost of centering and shuttering - all work up to plinth level : 8 providing and laying cement concrete 1:1½:3 (1 cement: 1½ coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing. 9 providing and fixing up to floor five level precast cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20mm nominal size derived from natural sources) string or lacing courses, copings, bed plates, anchor blocks, plain window sills, shelves, louvers, steps, stair cases, etc., including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering complete. 10 providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-iii) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) 11 extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturers specification. 12 making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-iii) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. 13 providing and laying in positiongrade 1:1.5:3 (1 cement : 1.5 coarse sand (zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level : 14 providing and laying in positiongrade 1:2:4 (1 cement : 2 coarse sand (zone-iii) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level : 15 reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 16 reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). 17 centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete 18 centering and shuttering including strutting, propping etc. and removal of form for walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. 19 centering and shuttering including strutting, propping etc. and removal of form forsuspended floors, roofs, landings, balconies and access platform 20 centering and shuttering including strutting, propping etc. and removal of form for shelves (cast in situ) 21 centering and shuttering including strutting, propping etc. and removal of form for lintels, beams, plinth beams, girders, bressumers and cantilevers 22 centering and shuttering including strutting, propping etc. and removal of form for columns, pillars, piers, abutments, posts and struts 23 centering and shuttering including strutting, propping etc. and removal of form for stairs, (excluding landings) except spiral-staircases 24 centering and shuttering including strutting, propping etc. and removal of form for spiral staircases (including landing) 25 centering and shuttering including strutting, propping etc. and removal of form for small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like 26 centering and shuttering including strutting, propping etc. and removal of form for small surfaces such as cantilever ends, brackets and ends of steps, caps and bases to pilasters and columns and the like 27 centering and shuttering including strutting, propping etc. and removal of form for weather shade, chajjas, corbels etc., including edges 28 centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick 29 centering and shuttering including strutting, propping etc. and removal of form for lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick 30 mild steel and medium tensile steel bars for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 31 mild steel and medium tensile steel bars for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. 32 smooth finishing of the exposed surface of r.c.c. work with 6 mm thick cement mortar 1:3 (1 cement : 3 fine sand). 33 add for plaster drip course/ groove in plastered surface or moulding to r.c.c. projections. 34 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in foundation and plinth in cement mortar 1:6 (1 cement : 6 coarse sand) 35 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in cement mortar 1:6 (1 cement : 6 coarse sand) 36 half brick masonry with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in foundations and plinth in cement mortar 1:4 (1 cement : 4 coarse sand) 37 half brick masonry with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level. cement mortar 1:4 (1 cement :4 coarse sand) 38 providing and fixing 18 mm thick granite stone slab of colour black, cherry/ruby red gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels (area of slab over 0.50 sqm) 39 providing edge moulding to 18 mm thick granite workcounters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by engineer-in-charge. 40 extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. 41 providing and fixing plywood 4 mm thick, one side decorative veneer conforming to is: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with : 42 providing and fixing 4mm thick coir veneer board, isi marked is : 14842, plain lining with necessary screws, priming coat on unexposed surface etc., complete. 43 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer-in-charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 44 providing second class teak wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). 45 providing and fixing 2nd class teak wood size 50x12 mm moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 46 providing and fixing second class teak wood panelled or panelled and glazed 30 mm thick shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of engineer-in-charge. (note:- butt hingesand necessary screwsshall be paid separately) 47 providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with isi, is : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. 48 providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with isi, is : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. 49 providing and fixing30mm thick glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes (weight not less than 10 kg per sqm) fixing with isi marked m.s. pressed butt hinges bright finished of required size with necessary screws.(kiln seasoned and chemically treated hollock wood) 50 providing and fixing35mm thick glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes (weight not less than 10 kg per sqm) fixing with isi marked m.s. pressed butt hinges bright finished of required size with necessary screws.(kiln seasoned selected planks of sheesham wood) 51 providing and fixing30mm thick glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes (weight not less than 10 kg per sqm) fixing with isi marked m.s. pressed butt hinges bright finished of required size with necessary screws.(kiln seasoned selected planks of sheesham wood) 52 providing and fixing30mm thick panelled or panelled & glazed shutters for cup board using 4 mm thick float glass panes (weight not less than 10 kg per sqm) fixing with isi marked m.s. pressed butt hinges bright finished of required size with necessary screws.(second class teak wood including isi marked anodised aluminium butt hinges with necessary screws) 53 providing and fixing isi marked 35mm thick flush door shutters conforming to is : 2202 (part i) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters ( including isi marked stainless steel butt hinges with necessary screws) 54 providing and fixing isi marked 30mm thick flush door shutters conforming to is : 2202 (part i) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters ( including isi marked stainless steel butt hinges with necessary screws) 55 providing and fixing isi marked 35mm thick flush door shutters conforming to is : 2202 (part i) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters ( including isi marked stainless steel butt hinges with necessary screws) 56 extra for providing and fixing flush doors with on one side only decorative veneering instead of non decorative isi marked flush door shutters conforming to is: 2202 (part i) 57 providing and fixing 12mm dia chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with c.p. brass screws andpvc sleeves etc., wherever necessary complete : 58 providing and fixing 20mm dia chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with c.p. brass screws andpvc sleeves etc., wherever necessary complete : 59 providing and fixing 25mm dia chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with c.p. brass screws andpvc sleeves etc., wherever necessary complete : 60 providing and fixing 20mm dia (heavy type) nickel plated m.s. pipe curtain rods with nickel plated brackets : 61 providing and fixing 25mm dia (heavy type) nickel plated m.s. pipe curtain rods with nickel plated brackets : 62 providing and fixing hard drawn steel wire fabric 75x25 mm mesh of weight not less than 7.75 kg per sqm to window frames etc. including 62x19 mm beading of second class teak wood and priming coat with approved steel primer all complete. 63 providing and fixing 125x65x2.12 mm isi marked is:1341 oxidised m.s. pressed butt hinges with necessary screws etc. complete. (copper oxidised as per is 1378) 64 providing and fixing 100x58x1.90 mmisi marked is:1341 oxidised m.s. pressed butt hinges with necessary screws etc. complete. (copper oxidised as per is 1378) 65 providing and fixing 75x47x1.70 mmisi marked is:1341 oxidised m.s. pressed butt hinges with necessary screws etc. complete. (copper oxidised as per is 1378) 66 providing and fixing 50x37x1.50 mmisi marked is:1341 oxidised m.s. pressed butt hinges with necessary screws etc. complete. (copper oxidised as per is 1378) 67 providing and fixing 150 mm isi marked oxidised m.s. single acting spring hinges with necessary screws etc. complete (copper oxidised as per is 1378) 68 providing and fixing 125 mm isi marked oxidised m.s. single acting spring hinges with necessary screws etc. complete (copper oxidised as per is 1378) 69 providing and fixing 100 mm isi marked oxidised m.s. single acting spring hinges with necessary screws etc. complete (copper oxidised as per is 1378) 70 providing and fixing 250x16 mm isi marked oxidised m.s. sliding door bolts with nuts and screws etc. complete (copper oxidised as per is 1378) 71 providing and 250x10 mm fixing isi marked oxidised m.s. tower bolt black finish, (barrel type) with necessary screws etc. complete (copper oxidised as per is 1378) 72 providing and 200x10 mm fixing isi marked oxidised m.s. tower bolt black finish, (barrel type) with necessary screws etc. complete (copper oxidised as per is 1378) 73 providing and 150x10 mm fixing isi marked oxidised m.s. tower bolt black finish, (barrel type) with necessary screws etc. complete (copper oxidised as per is 1378) 74 providing and 100x10 mm fixing isi marked oxidised m.s. tower bolt black finish, (barrel type) with necessary screws etc. complete (copper oxidised as per is 1378) 75 providing and fixing isi marked 85x42 mm oxidised m.s. pull bolt lock conforming to is : 7534 with necessary screws bolts, nut and washers etc. complete (copper oxidised as per is 1378). 76 providing and fixing 125 mm isi marked oxidised m.s. handles conforming to is:4992 with necessary screws etc. complete (copper oxidised as per is 1378) 77 providing and fixing 100 mm isi marked oxidised m.s. handles conforming to is:4992 with necessary screws etc. complete (copper oxidised as per is 1378) 78 providing and fixing 75 mm isi marked oxidised m.s. handles conforming to is:4992 with necessary screws etc. complete (copper oxidised as per is 1378) 79 providing and fixing 150 mm oxidised m.s. hasp and staple (safety type) conforming to is : 363 with necessary screws etc. complete (copper oxidised as per is 1378) 80 providing and fixing 115 mm oxidised m.s. hasp and staple (safety type) conforming to is : 363 with necessary screws etc. complete (copper oxidised as per is 1378) 81 providing and fixing 90 mm oxidised m.s. hasp and staple (safety type) conforming to is : 363 with necessary screws etc. complete (copper oxidised as per is 1378) 82 providing and fixing 300 mm (weighing not less than 330 grams) oxidised m.s. casement stays (straight peg type) with necessary screws etc. complete (copper oxidised as per is 1378) 83 providing and fixing 125mm special quality bright finished brass handles with screws for cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 84 providing and fixing 100mm special quality bright finished brass handles with screws for cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 85 providing and fixing 75mm special quality bright finished brass handles with screws for cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 86 providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. 87 providing and fixing triple strip vertical type magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete. 88 providing and fixing double strip (horizontal type) magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete. 89 providing and fixing factory made upvc door frame made of upvc extruded sections having an overall dimension as below (tolerance ±1mm),with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. the hinge side vertical of the frames reinforced by galvanized m.s. tube of size 19 x 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of engineer- in-charge (extruded section profile size 48x40 mm) 90 providing and fixing factory made upvc door frame made of upvc extruded sections having an overall dimension as below (tolerance ±1mm),with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. the hinge side vertical of the frames reinforced by galvanized m.s. tube of size 19 x 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of engineer- in-charge (extruded section profile size 42x50 mm) 91 providing and fixing 12 mm thick fire retardant plywood conforming to is: 5509 panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. 92 providing and fixing cup board shutters 25 mm thick, with pre-laminated flat pressed three layer particle board or graded wood particle board is: 12823 marked, exterior grade (grade l type ll), having one side decorative lamination and other side balancing lamination, including iind class teak wood lipping of 25 mm wide x12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of the engineer-in-charge 93 providing and fixing aluminum u beading of required size to pre-laminated/flush door shutter, including fixing etc. complete as per direction of engineer-in-charge. 94 providing and fixing casement handle made of zinc alloyed (white powder coated) for upvc casement window with necessary screws etc. complete. 95 providing and fixing zinc alloyed (white powder coated) touch lock for upvc sliding window with necessary screws etc. complete. 96 providing and fixing steel roller for upvc sliding window with necessary screws etc. complete. 97 providing and fixing steel roller for upvc sliding door with necessary screws etc. complete. 98 providing and fixing steel (white power coated) crescent lock for upvc sliding window/ door with necessary screws etc. complete. 99 providing and fixing 18mm thick both sides pre-laminated cement bonded wood particle board as per is : 15786:2008 of approved brand and shade with suitable full threaded steel screws etc. in partitions, boxes, shelves, racks and cupboard, kitchen cabinet under kitchen counter etc. all complete as per direction of engineer-in-charge (note: fittings to be paid separately). 100 providing and fixing 6mm thick both sides pre-laminated cement bonded wood particle board as per is : 15786:2008 of approved brand and shade with suitable full threaded steel screws etc. on the backing of racks, drawer, cupboard, kitchen cabinet under kitchen counter etc. all complete as per direction of engineer-in-charge. 101 providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed bwp grade marine ply as per is 710 of approved brand including 2mm thick pvc edge banding tape with hot glue by edge bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete as per direction of engineer-in-charge.(payment of providing and fixing auto closing hinges shall be paid separately) 102 structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 103 providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of t-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer. 104 providing and fixing 1mm thick m.s. sheet door with frame of 40x40x6 mm angle iron and 3 mm m.s. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.(using m.s. angels 40x40x6 mm for diagonal braces) 105 providing and fixing stainless steel ( grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). 106 providing and fixing angle iron frames for doors, windows and ventilators of mild steel angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing t-iron frame or to the wall with dash fastener,including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of engineer-in-charge. 107 brick on edge flooring with bricks of class designation 7.5 on a bed of 12 mm cement mortar with 1:6 (1cement : 6 coarse sand) including filling the joints with same mortar, with common burnt clay non modular bricks: 108 dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with jamuna sand, with common burnt clay non modular bricks. 109 40 mm thick with 20 mm nominal size stone aggregate cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 110 18 mm thick cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. 111 providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to is : 15622 of approved make in colours such as white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 112 cement concrete pavement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete. 113 25 mm thick kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 114 deduct for not using 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) bedding in laying of floor tiles and jointing with grey cement slurry @ 3.3 kg/ sqm. 115 fixing glazed/ ceramic/ vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (water based) conforming to is: 15477, in average 3mm thickness. 116 kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 117 providing and fixing 1st quality ceramic glazed floor tiles conforming to is : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. 118 providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to is : 15622, of approved make, in all colours, shades, except white, ivory, grey, fume red brown, laid on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete. 119 providing and laying vitrified floor tiles size 600x600 mm(thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding grouting the joints with white cement and matching pigments etc., complete. 120 providing 1 mm thick with zinc coating not less than 275 gm/ m² corrugated g.s. sheet roofing including vertical / curved surface fixed with polymer coated j or l hooks, bolts and nuts 8 mm diameter with bitumen and g.i. limpet washers or with g.i. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 121 making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over p.v.c. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. 122 providing & fixing 0.56 mm, aluminium color coated troughed profile with center to center pitch of 200 mm, depth of 32 mm, overall profile width1092 mm, cover width 1000mm at all heights, levels and locations colour finish aluminium alloy roofing sheets of alloyis designation31500, temper hx8 conforming to is 737 and dimensions as per is code 2676 with characteristics of good formability and corrosion resistance. the profile sheets shall be fixed to truss members in slope or required pitch or curvature with hex cap headed self drilling/tapping stainless steel screws m6, 50 mm long with 3 mm epdm seal washer etc. all inclusive of labour, scaffolding, t&p and sundries etc. complete as per directions of the engineer-in-charge. (cost of truss/frame work shall be paid separately). 123 providing and fixing precoated/mill finish aluminium ridges plain (500- 600mm) of pre-coated colour or mill finishaluminium roofing accessories in 0.71 mm thickness ,alloy 31500 (is designation) [aluminium alloy (aa) 3004 (iso designation)]for color, coating shall be 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns, using self drilling/tapping ss screws of size 6 x 50mm with 3mm thick epdm seal and ss plain washer complete : 124 providing 10 mm thick plaster of paris (gypsum anhydrous) flat surfaces ceiling up to a height of 5 m above floor level, over first class kail wood strips 25x6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame (frame work to be paid separately): 125 12.5 mm thick fully perforated gypsum board tile made from plasterboard having glass fibre conforming to is: 2095 part i, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an nrc (noise reduction coefficient) of 0.79, with 50 mm resin bonded glass wool backing. 126 12 mm cement plaster of mix :1:4 (1 cement: 4 fine sand) 127 12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand) 128 12 mm cement plaster finished with a floating coat of neat cement of mix : 1:3 (1 cement: 3 fine sand) 129 12 mm cement plaster finished with a floating coat of neat cement of mix : 1:4 (1 cement: 4 fine sand) 130 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) 131 neat cement punning. 132 distempering with 1st quality acrylic distemper (ready mixed) new work (two or more coats) over and including water thinnable priming coat with cement primer having voc content less than50 gram/litre of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : 133 finishing walls for new work (two or more coats applied @ 3.84 kg/10 sqm) with water proofing cement paint of required shade : 134 finishing walls for new work (two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) with acrylic smooth exterior paint of required shade : 135 finishing walls for new work (two or more coats applied @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. with ready mixed premium acrylic emulsion paint (company depot tinted) having voc less than 50 gm/litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shadewith silicon additives. 136 with ready mixed aluminium primer of approved brand and manufacture on resinous wood and plywood 137 with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works 138 with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel work (second coat) 139 painting (two or more coats) on 100mm diameter rain water, soil waste and vent pipes and fittings with synthetic enamel paint of approved brand and manufacture and required colour over a priming coat of approved steel primer on new work. 140 painting (two or more coats) on 150mm diameter rain water, soil waste and vent pipes and fittings with synthetic enamel paint of approved brand and manufacture and required colour over a priming coat of approved steel primer on new work. 141 painting two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 142 polishing on new wood work with ready mixed wax polish of approved brand and manufacture : 143 lettering with black japan paint of approved brand and manufacture 144 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 145 distempering for old work (one or more coats) with 1st quality acrylic distemper (ready mixed) having voc (volatile organic compound ) content less than 50 gram/ litre, of approved brand and manufacturerincluding applying additional coats wherever required to achieve even shade and colour 146 applying priming coats with water thinnable cement primer on wall surface having voc content less than 50 grams/litre of approved brand and manufacture. 147 6 mm plaster on cement concrete or reinforced cement concrete work with white cement based polymer modified self curing mortar of approved make as per the direction of engineer-in-charge. 148 removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 149 removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 150 polishing on old wood work with ready made wax polish of approved brand and manufacture : 151 painting (one or more coats) with black japan paint of approved brand and manufacture to give an even shade. 152 finishing walls for old work (two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface with acrylic smooth exterior paint of required shade : 153 repairs to plaster of thickness 12 mm to 20 mm with cement mortar 1:4 (1 cement : 4 fine sand) in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of engineer-in-charge. 154 fixing door chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per direction of engineer-in-charge. 155 fixing chowkhat in existing opening in brick/ rcc wall with dash fasteners/chemical fasteners of appropriate size (3 nos on each vertical member of door chowkhat and 2 nos on each vertical member of window chowkhats), including cost of dash fasteners/ chemical fastener. 156 making the opening for door/ window/ clerestory window in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete, to match existing surface i/c disposal of mulba/ rubbish to the nearest municipal dumping ground, all complete as per direction of engineer-in-charge. 157 renewing float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm) with putty and nails wherever necessary including racking out the old putty: 158 renewing float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/sqm) with putty and nails wherever necessary including racking out the old putty: 159 renewal of old putty of glass panes (length) 160 refixing old glass panes with putty and nails 161 fixing old glass panes with wooden fillets (excluding cost of fillets) 162 renewing bottom rail and/or top runner of collapsible gate including making good all damages and applying priming coat of zinc chromate yellow primer of approved brand and manufacturer. 163 pumping out water caused by springs, tidal or river seepage, broken water mains or drains and the like. 164 providing and fixing 20 mm diameter. brass curtain rods ofwall thickness 1.25 mm with two brass brackets fixed with brass screws and wooden plugs etc. wherever necessary complete. 165 repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm and under, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modifiedself curing mortar, including disposal of rubbish, all completeas per the direction of engineer-in-charge. 166 cleaning and desilting of gully trap chamber, including removal of rubbish mixed with earth etc. and disposal of same, all as per the direction of engineer-in-charge. 167 disconnecting damaged overhead/terrace pvc water storage tankof any size from water supply line and removing from the terrace including shifting at ground level as per direction of engineer-in-charge. 168 providing & fixing orissa pattern w.c pan of size 580x440 mm white vitreous china water closet squatting pan (indian type) along withs or p trap including dismantling of old wc seat and s or p trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of engineer-in charge. 169 dismantlingw.c.pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of engineer-in-charge. 170 dismantling 15 to 40 mm dia g.i. pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of engineer-in-charge.(a) internal work- exposed on wall 171 taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the engineer-in-charge. 172 demolishing lime concrete manually/ by mechanical means and disposal of material within 50 metres lead as per direction of engineer- in-charge. 173 demolishing nominal cementconcrete 1:3:6 or richer mix (i/c equivalent design mix manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer - in - charge. 174 demolishing nominal cementconcrete 1:4:8 or leaner mix (i/c equivalent design mix manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer - in - charge. 175 demolishing r.c.c. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of engineer - in- charge. 176 demolishing brick work in cement mortar manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge. 177 removing mortar from bricks in from brick work in cement mortar and cleaning bricks including stacking within a lead of 50 m (stacks of cleaned bricks shall be measured): 178 dismantling doors, windows and clerestory windows (steel or wood) shutter of area 3 sq. metres and below including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : 179 dismantling doors, windows and clerestory windows (steel or wood) shutter of area beyond 3 sq. metres including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : 180 taking out doors, windows and clerestory window shutters (steel or wood) of area 3 sq. metres and belowincluding stacking within 50 metres lead : 181 taking out doors, windows and clerestory window shutters (steel or wood) of area beyond 3 sq. metres including stacking within 50 metres lead : 182 dismantling for thickness of tiles 10 mm to 25 mmwork in floors and roofs laid in cement mortar including stacking material within 50 metres lead. 183 dismantling for thickness of tiles above 25 mm and up to 40 mmwork in floors and roofs laid in cement mortar including stacking material within 50 metres lead. 184 demolishing dry brick pitching in floors, drains etc. including stacking of serviceable material and disposal of unserviceable material within 50 metres lead : 185 dismantling g.s. sheetroofingincludingridges,hips,valleysandguttersetc., and stacking the material within 50 metres lead of: 186 dismantling asbestos cement sheetroofingincludingridges,hips,valleysandguttersetc., and stacking the material within 50 metres lead of: 187 dismantling tiled roofing with battens, boarding etc. complete includingstackingofserviceablematerialanddisposalofunserviceable material within 50 metres lead. 188 dismantlingbarbedwireorflexiblewireropeinfencingincludingmaking rolls and stacking within 50 metres lead. 189 dismantling40 mm thick precast concrete orstone slabsin walls, partition walls etc. including stacking within 50 metres lead : 190 dismantling40 mm to 75mmthick precast concrete orstone slabsin walls, partition walls etc. including stacking within 50 metres lead : 191 dismantling cement asbestos or other hard board ceiling or partition wallsincludingstackingofserviceablematerialsanddisposalof unserviceable materials within 50 metres lead. 192 dismantling of flushing cistern of all types(c.i./pvc/vitrious china) includingstackingofusefulmaterialsnearthesiteanddisposalofunserviceable materials within 50 metres lead. 193 dismantling old plaster or skirting raking out joints and cleaning the surfaceforplasterincludingdisposalofrubbishtothedumping ground within 50 metres lead. 194 dismantlingaluminium/gypsumpartitions,doors,windows,fixed glazing and false ceiling including disposal of unserviceable material andstackingofserviceablematerialwithin50metersleadas directed by engineer-in-charge. 195 disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping groundorasapprovedbyengineer-in-charge,beyond50minitial lead, for all leads including all lifts involved. 196 cuttingroadandmakinggoodthesameincludingsupplyofextra quantities of materials i.e. aggregate, moorum screening, red bajri and labour (required.bituminous portion) 197 paintingroadsurfacemarking for new work (two or more coats) withadequatenosofcoatstogive uniform finish with ready mixed road marking paint conforming to is : 164, on bituminous surface in white/yellow shade, including cleaning thesurfaceofalldirt,scales,oil,greaseandforeignmaterialetc. complete. 198 paintingroadsurfacemarking for old work (one or more coats) withadequatenosofcoatstogive uniform finish with ready mixed road marking paint conforming to is : 164, on bituminous surface in white/yellow shade, including cleaning thesurfaceofalldirt,scales,oil,greaseandforeignmaterialetc. complete. 199 taking out existing cc interlocking paver blocks from footpath/ central verge,includingremovalofrubbishetc.,disposalofunserviceable materialtothedumpingground,forwhichpaymentshallbemade separately and stackingof serviceable materialwithin 50metre lead as per direction of engineer-in-charge. 200 layingoldcementcocreteinterlockingpaverblocksofanydesign/ shapelaidinrequiredline,level,curvature,colourandpatternover and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of engineer- in-charge. (old cc paver blocks shall be supplied by the department free of cost). 201 providing and laying 80mmthickc.c.paverblockofm-35gradewith approved colour design and pattern.factory made chamfered edge cement concrete paverblocksinfootpath,parks,lawns,drivewaysorlighttraffic parkingetc,ofrequiredstrength,thickness&size/shape,madeby tablevibratorymethodusingpumould,laidinrequiredcolour& patternover50mmthickcompactedbedof sand,compactingand properembedding/layingofinterlockingpaverblocksintothesand beddinglayerthroughvibratorycompactionbyusingplatevibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. completeall as per direction of engineer-in-charge. 202 providing andfixingwhitevitreouschinaorissapatternw.c.panofsize 580x440 mm with integral type foot rests waterclosetsquatting pan(indian typew.c. pan)with100mmsandcastironporstrap,10litrelowlevel whitep.v.c.flushingcistern,includingflushpipe,withmanually controlleddevice(handlelever)conformingtois:7231,withall fittingsandfixturescomplete,includingcuttingandmakinggood the walls and floors wherever required: 203 providing and fixing w.c. pan with isi marked white solid plastic seat and lid white vitreous china pedestal type water closet (european type) with seat and lid, 10 litre low level white vitreous china flushing cistern & c.p. flush bend with fittings & c.i. brackets, 40 mm flush bend, overflow arrangement with specials of standard makeandmosquitoproofcouplingofapprovedmunicipaldesign complete,includingpaintingoffittingsandbrackets,cuttingand making good the walls and floors wherever required : 204 providingandfixing oneurinalbasinwith5litrewhitep.v.c.automaticflushing cistern whitevitreouschinaflatbackorwallcorner typelippedfronturinalbasinof430x260x350mmand 340x410x265 mm sizes respectively with automatic flushing cistern withstandardflushpipeandc.p.brassspreaderswithbrass unions and g.i clamps complete, including painting of fittings and brackets,cuttingandmakinggoodthewallsandfloorswhereverrequired : 205 providingandfixingwhitevitreouschinawashbasinsize550x400mm with a pair of 15 mm c.p. brass pillar taps washbasinwithc.i.brackets,15mmc.p. brasspillartaps,32mmc.p.brasswasteofstandardpattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 206 providing and fixing wash basin with c.i. brackets, 15 mm dia cp brasssingleholebasinmixerofapprovedqualityandmake, including painting of fittings and brackets, cutting and making goodthe walls wherever required:- (a)white vitreous china wash basin size 550x400 mm with a 15 mm cp brass single hole basin mixer 207 providingandfixingwhitevitreouschinapedestalforwashbasin completelyrecessedatthebackforthereceptionofpipesand fittings. 208 providing and fixing 610x510 mm bowl depth 200 mm stainless steel a isi 304 (18/8) kitchen sink as per is:13983 with c.i. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required (kitchen sink without drain board) 209 providing and fixing 8 mm dia c.p. / s.s. jet with flexible tube upto 1 metre long with s.s. triangular plate to eureopean type w.c. of quality and make as approved by engineer - in - charge. 210 providing and fixing 10 litre capacity - white p.v.c. low level flushing cistern with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete. 211 providing and fixing 10 litre (full flush) capacity-white controlled flush, low level cistern made of vitreous china with all fittings complete. 212 providing and fixing g.i. inlet connection for flush pipe connecting with w.c. pan. 213 providing and fixing cp brass 32mm size bottle trap of approved quality & make and as per the direction of engineer-in-charge. 214 providing and fixing15 mm nominal dia cp brass single lever telephonic wall mixer of quality & make as approved by engineer in charge. 215 providingandfixing 32mm diaflexible pipe p.v.c.wastepipeforsinkorwashbasin including p.v.c. waste fittings complete. 216 providing and fixing 100 mm sand cast iron grating for gully trap. 217 providingandfixinginposition25mmdiametermosquitoproofcoupling of approved municipal design. 218 providing and fixing 600x450 mm beveled edge mirror of superior glass(ofapprovedquality)completewith6mmthickhardboard ground fixed to wooden cleats with c.p. brass screws and washerscomplete. 219 providing andfixing circular shape 450 mm dia mirrorofsuperiorglass(ofapprovedquality)andofrequiredshapeandsizewithplasticmouldedframeof approved make and shade with 6 mm thick hard board backing : 220 providing andfixing 600x120x5 mmglass shelfwith edges round off, supported on anodised aluminium angle frame with c.p. brass bracketsandguardrailcompletefixedwith40mmlongscrews, rawl plugs etc., complete. 221 providing and fixing c.p. brass toilet paper holder : 222 providing and fixing ptmt liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. 223 providing and fixing ptmt towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. 224 providing and fixing ptmt 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour. 225 providing and fixing ptmt 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour. 226 providing and fixing ptmt shelf 440 mm long, 124 mm width and 36 mm height of approved quality and colour, weighing not less than 300 gms. 227 providing and fixing ptmt 15 mm urinal spreader size 95x69x100 mm with 1/2 bsp thread and shapes, weighing not less than 60 gms. 228 providing and fixing 15 mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. (internal work - exposed on wall) 229 providing and fixing 20 mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. (internal work - exposed on wall) 230 providing and fixing 25 mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. (internal work - exposed on wall) 231 providing and fixing 15 mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge.(concealed work) 232 providing and fixing 20 mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge.(concealed work) 233 providing and fixing 25 mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge.(concealed work) 234 providing and fixing 15 mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings this includes jointing of pipes & fittings with one step cpvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge.(external work) 235 providing and fixing 20 mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings this includes jointing of pipes & fittings with one step cpvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge.(external work) 236 providing and fixing 25mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings this includes jointing of pipes & fittings with one step cpvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge.(external work) 237 providing and fixing 32mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings this includes jointing of pipes & fittings with one step cpvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge.(external work) 238 providing and fixing 40mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings this includes jointing of pipes & fittings with one step cpvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge.(external work) 239 providing and fixing 50mm nominal dia chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings this includes jointing of pipes & fittings with one step cpvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge.(external work) 240 providing and fixing 15 mm dia nominal bore g.i. pipes complete with g.i. fittings and clamps, i/c cutting and making good the walls etc.(internal work - exposed on wall) 241 providing and fixing 20 mm dia nominal bore g.i. pipes complete with g.i. fittings and clamps, i/c cutting and making good the walls etc.(internal work - exposed on wall) 242 providing and fixing 25 mm dia nominal bore g.i. pipes complete with g.i. fittings and clamps, i/c cutting and making good the walls etc.(internal work - exposed on wall) 243 providing and fixing 15 mm dia nominal bore g.i. pipes complete with g.i. fittings including trenching and refilling etc.(external work) 244 providing and fixing 20 mm dia nominal bore g.i. pipes complete with g.i. fittings including trenching and refilling etc.(external work) 245 providing and fixing 25 mm dia nominal bore g.i. pipes complete with g.i. fittings including trenching and refilling etc.(external work) 246 providing and fixing 32 mm dia nominal bore g.i. pipes complete with g.i. fittings including trenching and refilling etc.(external work) 247 providing and fixing 40 mm dia nominal bore g.i. pipes complete with g.i. fittings including trenching and refilling etc.(external work) 248 providing and fixing 50 mm dia nominal bore g.i. pipes complete with g.i. fittings including trenching and refilling etc.(external work) 249 providing and fixing 25 mm nominal bore gun metal gate valve with c.i. wheel of approved quality (screwed end) : 250 providing and fixing 20 mm nominal bore gun metal gate valve with c.i. wheel of approved quality (screwed end) : 251 providing and fixing 32 mm nominal bore gun metal gate valve with c.i. wheel of approved quality (screwed end) : 252 providing and fixing 15 mm nominal bore ball valve (brass) of approved quality, high or low pressure, with plastic floats complete : 253 providing and fixing 20 mm nominal bore ball valve (brass) of approved quality, high or low pressure, with plastic floats complete : 254 providing and fixing 15mm norminal bore 45 cm length uplasticised pvc connection pipe with brass unions : 255 providing and fixing 20mm norminal bore 45 cm length uplasticised pvc connection pipe with brass unions : 256 providing and fixing 100 mm diameter c.p. brass shower rose with 15 or 20 mm inlet : 257 providing and fixing 150 mm diameter c.p. brass shower rose with 15 or 20 mm inlet : 258 providing and placing on terrace (at all floor levels) polyethylene water storage tank, is : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 259 providing and fixing 15 mm nominal bore c.p. brass bib cock of approved quality conforming to is:8931 : 260 providing and fixing 15 mm nominal bore c.p. brass long nose bib cock of approved quality conforming to is standards and weighing not less than 810 gms. 261 providing and fixing 15 mm nominal bore c.p. brass long body bib cock of approved quality conforming to is standards and weighing not less than 690 gms. 262 providing and fixing 15mm nominal bore c.p. brass angle valve for basin mixer and geyser points of approved quality conforming to is:8931 263 providing and fixing c.p. brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of engineer-in-charge. 264 cutting holes up to 15x15 cm in r.c.c. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. 265 providing and fixing anodised aluminium (anodised transparent or dyed to required shade according to is: 1868, minimum anodic coating of grade ac 15) work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer-in-charge. (glazing, paneling and dash fastenersto be paid for separately) :(for fixed portion) 266 providing and fixing powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer-in-charge. (glazing, paneling and dash fastenersto be paid for separately) :(for fixed portion) 267 providing and fixing glazing with float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (cost of aluminium snap beading shall be paid in basic item): 268 providing and fixing glazing with float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (cost of aluminium snap beading shall be paid in basic item): 269 providing and fixing glazing with float glass panes of 8 mm thickness (weight not less than 20 kg/sqm)in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (cost of aluminium snap beading shall be paid in basic item): 270 providing and fixing with stainless steel cover plate minimum 1.25 mm thicknessdouble action hydraulic floor spring of approved brand and manufacture conforming to is : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece m.s. sheet outer box with slide plate etc. complete as per the direction of engineer-in-charge. 271 providing and fixing with brass cover plate minimum 1.25 mm thicknessdouble action hydraulic floor spring of approved brand and manufacture conforming to is : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece m.s. sheet outer box with slide plate etc. complete as per the direction of engineer-in-charge. 272 providing and laying water proofing treatment in sunken portion of wcs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :(a) first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. this layer will be allowed to air cure for 4 hours.(b) second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. this layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (the rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.) 273 providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:(a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm.(b) laying second layer of fibre glass cloth when the first layer is still green. overlaps of joints of fibre cloth should not be less than 10 cm.(c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. this will be allowed to air cure for 4 hours followed by water curing for 48 hours. the entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around.(d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. (for the purpose of measurement the entire treated surface will be measured.) 274 providing & applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg /10 sqm. one coat of self priming of cementatious waterproofing polymer(dilution with water in the ratio of 1:1) and two coats of cementatious waterproofing polymer(dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of engineer-in-charge. 275 providing and applying of swellable type water stop tape, 19mm x 25mm thick in linear meter (expansive nature) for construction joints treatment of rcc structure such as raft slab, retaining walls, water storage tank and at the junctions of raft slab with the retaining walls etc.. after cleaning the surface, one coat of required primer for swellable water stop tape shall be applied throughout the length of the joint @3.78 litre per 240 running meter. over the primed surface swellable type water stop tape shall be placed. the work shall be carried out all complete as per specification and the direction of the engineer-in-charge. the product performance shall carry guarantee for 10 years against any leakage. 276 providing and fixing with15mmthick fullyperforatedsquare/buttedgelightweightcalcium silicate panels/ tiles in position wall panelling at all heights with integral densified calcium silicatepanels/tilesofsize595x595mm,havingnrc(noisereductioncoefficient)of0.50 (minimum) as per is 8225:1987, light reflectance of 85% (minimum). non combustible as per bs:476 (part-4), fire performance as per bs:476 (part 6 &7), humidity resistanceof 100%,thermalconductivity<0.043w/mk asperastm518:1991, comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mmthickpressedsection(galvanizing@120gramspersqmincludingbothsides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor andceilingchannel sectionofsize50x32mfixedtothefloorandsoffitat600mm centersusing12mmdia,50mmlongwedgetypeexpandedzincalloy dashfastnerwith 10mm bolt. this same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. glasswool of 50mm thickness is then to be inserted in the slots and finallycalcium silicate non combustible panels/tiles are to bescrew fixed withselftapping panheadnickel coatedmild steelscrewsofsize13x3.2mmon tothisgridleavingan evengroove of1 mm betweenthepanels. the joints betweenthepanelsaretobedulyjointedandfinishedusingrecommendedjointing calcium silicate based compound and fiber joint tape roll 50mm wide(90 metre )roll and twocoatsofprimersuitableforpanellingaspermanufacturersspecificationasper direction of engineer-in-charge all complete. 277 providing and fixing with 16 mm thick beveled tegular mineral fibre false ceiling tile (nrc 0.55 to 0.6 mineral fibre false ceiling tiles at all heights of size 595x595mm of approved texture, design and pattern. the tiles should have humidity resistance (rh) of 99%,lightreflectance=85%,thermalconductivityk=0.052-0.057w/mk,fire performance as per (bs 476 pt - 6 &7)in true horizontal level suspended on interlocking t- grid of hot dipped all round galvanized iron section of 0.33 mmthick (galvanized @120 gsm)comprisingofmaintrunnersof15x32mmoflength3000mm,crosstofsize 15x32mm of length 1200 mm and secondary intermediate cross t of size 15x32 mm of length600mm toform gridmoduleofsize 600x600mm suspendedfrom ceiling using galvanizedmildsteelitem(galvanised@80gsm)50mmlong8mmouterdiameterm-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and l- shapeleveladjusterofsize85x25x2mm,spacedat1200mmcentretocentrealong main‘t’.thesystemshouldrestonperipherywalls/partitionswiththehelpofgi perimeter wall angle of size24x24x3000 mm made of 0.40 mm thicksheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry walls.s. screws. the exposed bottom portion of all t-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. the work shall be carriedoutasperspecifications,drawingsandasperdirectionsoftheengineer-in- charge. 278 providingandfixingharddrawnsteelwirefabricofsize75x25mmmeshorother suitable size wire mesh to be fixed & firmly anchored to the concrete surface by means of l shaped mild steel shear key welded with existing reinforcement including the cost of materials, labour, tool & plants as approved by engineer-in-charge. 279 fillingofjointsbetweenrccplinthbeam/floorslabandwallpanelofexternalwalls, toilet / bath room / wet areas walls on all floor and parapet wall over roof slab, stair case headroomatthetimeoferectionofgfrgpanelswithgroutrw/equivalentsealant compound after the erection of panelbeforethe infill of concrete in panel cavities and fine finish. this applies for all horizontal and vertical joints between gfrg wall and slab panels. 280 waterproofingtreatmentofverticaljoints(ofexternalsideandinternalside)between doorframe,window&ventilatorframes(onallfoursides)ofouterwalloverthe zycosil/equivalent & zycoprime/equivalent solution already applied (before the installation of door / window / ventilator frames in position) and fine finish with grout rw/equivalent. 281 waterproofingtreatmentofrccsunshadewith zycosil/equivalentwaterproofing solution(1litreofzycosil/equivalent&20litresofwaterstirredfirst&2litresof zycoprime/equivalent addedandstirred (total23litres))till itmeetsthesaturationlevel and testing as per rilem or bywater drops test in which water drops do not absorb but drops remain or rolls. 282 in-filling / sealing of joint between rcc lintel cum sunshade and wall (on external side) in all floors by pushing in grout rw/equivalentin paste form and coving 20 mm x 20 mm after applying a coat of zycosil/equivalent & zycoprime/equivalent solution before cement plastering of top, bottom and sides of rcc sunshade. 283 concreteworkwith40mmgaugebrickballastobtainedfrombreaking brick bats (brick bats supplied by the department free of cost) in proportion of 12:6:1 as in csi no. 5.01 includingcost of all labour, materials, t&p etc required for proper completion of work. 284 brickworkinfoundation&plinthwitholddismantled bricks(suppliedby departmentfreeofcost)andcoarsesand mortarin1:6includingsupply ofallothermaterials,labour,removingmortar&cleaningofold&usedbricks,t&p etc complete. 285 supply and filling brick bat in soak pit including all labour,material and t&petc complete. (for 01 soak pit) 286 supplying & fixing 24 gauge annodized aluminium sheet of approved qualityincludingcutting,wastageandfixingthesameoverthewooden door shutters with nails with all material, labour and t&p 287 providingandfixinginplaceafullheightstoragecabinet450mmdeep made with19 mm thick isi marked plyborad, allinterior surfaces to finishedwithpastingof0.8mmthickmicaandallexteriorsurfacestobe finshed with pasting of 1 mm thick mica of texture and colour as approved byengineerinchargeincludingalllabour,t&p,otheritemslike(butnot limitedto)fevicol,nailsscrews,higes,sliders,doorhandles,multipurpose lockofgodrejorequivalentrateetc.requiredforpropercompletionof works, to be measured interms of front area only. 288 providingandfixingfullheightpartitionwith02nos12mmthickisi marked ply board, all surfaces to finished withf 1 mm thick mica of texture andcolourasapprovedbyengineerinchargeandfixedinpolishedteak woodincludingalllabour,t&p,otheritemslike (butnot limitedto) fevicol, nailsscrews,hinges,sliders,doorhandles,multipurposelockofgodrejor equivalent rate etc. required for proper completion of works, to be measured interms of front area only 289 providingandfixing12mmthickframelesstoughenedglassdoorshutter ofapprovedbrandandmanufacture,includingprovidingandfixingtop& bottom pivot & double acting hydraulic floor spring type fixing arrangement ,doorhandle,lockandstopperetcandmakingnecessaryholesetc.for fixingrequireddoorfittings,allcompleteasperdirectionofengineer-in- charge 290 supply and fixing 6mm thick polycarbonate multiwall sheet ,fixing in position with j or u bolts 10 mm. dia with g.i. limpet & bitumen washers including supply of all materials, labour,wastage. and t&p etc. required for proper completion of the work. 291 providing (12x15) mm section groove in plasterincluding all material, labour andt&p etc. required for proper completion of the work.csi no.11.16 292 2.5 cm thick 1:1.5:3 plain cement concrete floor with cement, approved coarse sand & 2cm graded approved stone ballast laid in panels finished with 3mm floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified and removing any overlapping mortar at the joints of the panels if any and giving them a uniform finish including supply of all materials, labour and t&p etc, required for proper completion of the work. without base cccsi no.12.26 293 4.0 cm thick 1:1.5:3 plain cement concrete floor with cement, approved coarse sand & 2cm graded approved stone ballast laid in panels finished with 3mm floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified and removing any overlapping mortar at the joints of the panels if any and giving them a uniform finish including supply of all materials, labour and t&p etc, required for proper completion of the work. without base cc csi no. 12.28 294 dismantling ofdry b.o.e. floor and proper stacking of dismantled bricks as per direction of e/c. up to 60 m lead. 295 dismantling and re-laying of dry b.o.e. floor including cost of all labour and t&p required forproper completion of work.(labour rates only) 296 cleaning panes of glass with spirit of caustic soda including supply of all materials,labour and t&p etc.required for proper completion of the work. 297 cleaning of septic tank including disposal of waste out side the uppcl area as per direction of the engineer-in-charge including cost of all labour,t&p etc.required for proper completion of the work. 298 cleaning and opening of chocked w.c./ bath / kithchen pipe line including opening and refixing of chamber cover including washing etc. complete.(analysis based on nbo - 11 25.020. 299 s/laying chicken mesh of (20 mm.)hexagonal heavy quality over roofs of joints of roof as per direction of the engineer - in - charge. 300 cleaning of existing pipe line of different dia. ranging from 4 to 2 dia. including digging trenches and refilling, opening of pipes, cleaning of pipes, cutting, threading, if required fixing and including making good the road, wall etc as directed by the engineer i/c. 301 cleaning of existing water pipe line of different dia up to 2 dia including digging trenches and refilling,opening and cleaning of pipes,cutting,threading,if required fixing and including making good the road and wall etc. as directed by the engineer in charge. 302 cleaning of r.c.c. over head tank up to capacity of one lac. liters and chlorinating with bleaching power mixed to water as per direction of engineer - in - charge complete. 303 supply and mixing bleaching powder in over head tank as required or as directed by engineer - in - charge. 304 attending to petty maintenance service like plumbingservice,welder service, mansion service and carpenter servicerequired as below. (job attending by one no. plumber/welder/mason /carpenter with oneno. helper per hour or part of an hour.) 305 cleaning and sweeping of roof of residence as and when requiredincluding uprooting of rank vegetation and disposal of thegarbage upto 50 m. 306 providing and fixing of 150 mm dia pvc pipeof 6 kg/sqcmwith special such as tee, bend, socket, elbow etc including supply of all labour,material,t & p etc complete required for proper completion of work. 307 providing and laying 75 mm dia. swr, pvc ( finolex or equivalent ) pipe including cost of excavation, c.c etc including its jointing and connection, all materials, labour and t&p etc. required for proper completion of the work. 308 providing and laying 90 mm dia. swr, pvc ( finolex or equivalent ) pipe including cost of excavation, c.c etc including its jointing and connection, all materials, labour and t&p etc. required for proper completion of the work. 309 providing and laying 110 mm dia. swr, pvc ( finolex or equivalent ) pipe including cost of excavation, c.c etc including its jointing and connection, all materials, labour and t&p etc. required for proper completion of the work. 310 making arrangement for sweeping, cleaning of road, lanes in back of houses,collecting refuse of bushes & unwanted plants, vegetations etc. & disposal of all rubbish, materials industbins inside the colony area with engaging atleast one number of sweepers including all labour, t&p,etc.required for completion of work as directed by e/i. 311 making arrangement for sweeping, cleaning of ee,ecd(d), georgetown ,prayagraj office rooms, cleaning of dustbin, toilets , dusting of almirahs,tables etc. using phenyle,dusting cloth etc. and disposal of waste outside office premise in municipal dustbinswith engaging sufficient number ofsweepersincluding all labour, t&p,etc.required for completion of work as directed by e/i.(nsi)(consumable items as phenyle,dusting cloth ,brooms etc shall be provided by the department free of cost.) 312 cleaning of main drain or width more than 300mm including disposal of waste refuses studge out side the boards ara including washing and cleaning by clean water completely as per direction of the e/i. including cost of all labour, t&p etc. required for completion of the work. (csino.20.14) 313 cleaning of main drain or width less than 300mm including disposal of waste refuses studge out side the boards ara including washing and cleaning by clean water completely as per direction of the e/i. including cost of all labour, t&p etc. required for completion of the work. (csino.20.15) nsi sl. no.63 314 operation of tube well daily by a suitable experienced operator continously or in different intervals as per program as per program fixed by engineer-in-charge including opening and closing of valves,changing of fuse wire etc. as requrird for proper running of tube well. (nsi) 315 wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm frls pvc insulated copper conductor single core cable in surface / recessed medium class pvc conduit, with modular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm. frls pvc insulated copper conductor single core cable etc as required..group c 316 supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 amp socket outlet 317 supplying and fixing of 20 mm of medium class pvc conduit along with accessories in surface/recess including junction box, cutting the wall and making good the same in case of recessed conduit as required. 318 supplying and fixing of 25 mm of medium class pvc conduit along with accessories in surface/recess including junction box,cutting the wall and making good the same in case of recessed conduit as required. 319 wiring for circuit/ submain wiring with 2 x 2.5 sq. mm + 1 x 2.5 sq. mm earth wire of frls pvc insulated copper conductor, single core cable in surface/ recessed medium class pvc conduit as required. 320 wiring for circuit/ submain wiring with 2 x 4 sq. mm + 1 x 4 sq. mm earth wire of frls pvc insulated copper conductor, single core cable in surface/ recessed medium class pvc conduit as required. 321 wiring for circuit/ submain wiring with2 x 6 sq. mm + 1 x 6 sq. mm earth wire of frls pvc insulated copper conductor, single core cable in surface/ recessed medium class pvc conduit as required. 322 earthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required . 323 providing and laying earth connection from earth electrode with 6 swg dia g.i. wire in 15 mm dia g.i. pipe from earth electrode including connection with g.i. thimble excavation and re-filling as required. 324 supplying and fixing 5 amps to 32 amps rating,single pole, 240/415 volts, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. 325 supplying and fixing 63 amps, double pole, 240 volts, isolator in the existing mcb db complete with connections, testing and commissioning etc. as required. 326 supplying and fixing 40 amps, double pole, 240 volts, isolator in the existing mcb db complete with connections, testing and commissioning etc. as required. 327 supplying and fixing 4 way (4 + 12), double door, horizontal type three pole and neutral, sheet steel, mcb distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (but without mcb/rccb/isolator) 328 supplying and fixing of 4 way (4 + 12), double door surface/ recess mounting, vertical type, 415 volts, tpn mcb distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting mcbs (but without mcbs and incomer ) as required . (note : vertical type mcb tpdb is normally used where 3 phase outlets are required.) 329 wiring for light/ power plug with 2x4 sq. mm frls pvc insulated copper conductor single core cable in surface/ recessed medium class pvc conduit along with 1 no 4 sq. mm frls pvc insulated copper conductor single core cable for loop earthing as required. 330 supplying and fixing following size/ modules, gi box along with modular base & cover plate for modular switches in recess etc as required. 1 or 2 module (75mmx75mm) 331 supplying and fixing following size/ modules, gi box along with modular base & cover plate for modular switches in recess etc as required.3 module (100mmx75mm) 332 supplying and fixing following size/ modules, gi box along with modular base & cover plate for modular switches in recess etc as required. 4 module (125mmx75mm) 333 supplying and fixing following size/ modules, gi box along with modular base & cover plate for modular switches in recess etc as required. 6 module (200mmx75mm) 334 supplying and fixing following size/ modules, gi box along with modular base & cover plate for modular switches in recess etc as required. 8 module (125mmx125mm) 335 supplying and fixing following size/ modules, gi box along with modular base & cover plate for modular switches in recess etc as required. 12 module (200mmx150mm) 336 supplying and drawing following 3 x 2.5 sq. mm sizes of frls pvc insulated copper conductor, single core cable in the existing surface/ recessed steel/ pvc conduit as required. 337 supplying and drawing following 3 x 4 sq. mm sizes of frls pvc insulated copper conductor, single core cable in the existing surface/ recessed steel/ pvc conduit as required.(dsr e&m 2022 1.17.21) 338 rewinding of burnt ceiling fan with approved copper wire including cost of all materials, labour and t&p etc. complete (burnt wirewill not be taken back.) 339 greasing of ceiling fan after cleaning the bearing and shaft withoil / petrol and its testing. 340 supply and fixing of led tube light batten fitting suitable for up to 1 x 22 watt led tube light on surface complete in all respect.(csi no. 28.41) 341 supply of 9 watt led bulb make philips, syska, bajaj etc or its equivalent as directed by e/i. 342 supply, installation, testing and commissioning of 1200 mm sweep, bee 5 star rated, ceiling fan with brush less direct current (bldc) motor, class of insulation: b, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, power factor not less than 0.9, service value (cm/m/w) minimum 6.00, air delivery minimum 210 cum/min, 350 rpm (tolerance as per is: 374-2019), thd less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree c (max.), insulation resistance more than 2 mega ohm, suitable for 230 v, 50 hz, single phase ac supply, earthing etc. complete as required.(dsr e&m 2022 19.1) 343 supply and fixing of 5 blade exhaust fan ventile air dx 225 mm of havellsor equivalent make including all material, t&p etc required for proper completion of work as approved by engineer in charge.(csi no. 28.38) 344 supply and fixing of 3 blade wall fan ofhavells platina 400 mm or equivalent including all material, t&petc required for proper completion of work as approved by engineer in charge.(csi no. 28.37)

Related Searched Keywords : pvc bend

List of pvc-bend Tenders

Get pvc bend Tender Alert...

Related Searched Keywords : pvc bend

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us