Filters

List of edge-wall Tenders

List of latest edge-wall Tenders in Indian Tenders. Click on any edge-wall Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for edge-wall Tenders.

All-Tenders (13)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

Government Departments

TRN :49019871 | 21 May, 2025

Tender Value : 8.47 Lacs

Agra - Uttar Pradesh

Tender for tender for repair work of zone-1 ward no. 16 ratanpura nagla vida community hall. - cleaning of the site for warkable etc. all complete. (non scheduled) 2 1:5:10 (1 cement : 5 coarse sand (zone-iii) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) (dsr 2023 sh-4.1.10 ) 3 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in :cement mortar 1:4 (1 cement : 4 coarse sand) (dsr 2023 sh-6.4.1 ) 4 brick work 7 cm thick with common burnt clay f.p.s. (non modular) brick of class designation 7.5 in cement mortar 1:3 (1 cement : 3 coarse sand) in superstructure above plinth level and upto floor five level. (dsr 2023 sh-6.8 ) 5 reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills,taircases and spiral stair cases above plinth level up to floor fiveevel, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).(dsr 2023 sh-5.3 ) 6 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. thermo-mechanically treated bars of grade fe-500d or more(dsr 2023 sh-5.22.6) 7 centering and shuttering including strutting, propping etc. and removal of form work for :columns, piers, abutments, pillars, posts and struts(dsr 2023 sh-4.3.3 ) 8 12 mm cement plaster of mix : 1:4(1 cement: 4 fine sand)(dsr 2023 sh-13.1.1 ) 9 structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.(dsr 2023 sh-10.1 ) 10 providing and fixing 12 mm thick panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick.fire retardant plywood conforming to is: 5509(dsr 2023 sh-9.126.2 ) 11 providing and fixing isi marked is:1341 m.s. pressed butt hinges bright finished with necessary screws etc. complete :)75x47x1.70 mm (dsr 2023 sh-9.55.3 ) 12 providing & fixing decorative high pressure laminated sheet of plain / wood grain in gloss/ matt/ suede finish with high density protective surface layer and reverse side ofdhesive bonding quality conforming to is : 2046 type s including cost of adhesive of approved quality. 1.0 mm thick (dsr 2023 sh-9.127.2 ) 13 distempering with 1st quality acrylic distemper (ready mixed) having voc content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour new work (two or more coats) over and including water thinnable priming coat with cement primer having voc content less than 50 gram/litre (dsr 2023 sh-13.41.1 ) 14 painting steel work with deluxe multi surface paint to give an even shade. two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture(dsr 2023 sh-1021sub head : 13 finishing13.48.3 ) 15 providing & fixing white vitreous china water closet squatting pan (indian type) along with “s” or “p” trap including dismantling of old wc seat and “s” or “p” trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of engineer-in charge. long pattern w.c pan of size 580x440 mm (dsr 2023 sh-14.80.1) 16 providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require white vitreous china flat back wash basin size 450x 300 mm with single 15mm c.p. brass(dsr 2023 sh-17.7.7) 17 providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white pvc automatic flushing cistern, with fittings, standard size c.p. brass flush pipe, spreaders with unions and clamps (all in c.p. brass) with waste fitting as per is: 2556, c.i. trap with outlet grating and other couplings in c.p. brass, including painting of fittings and cutting and making good the walls and floors wherever required(dsr 2023 sh-17.5.1 ) 18 providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white p.v.c. automatic flushing cistern, with fittings, standard size g.i./ pvc flush pipe for back and front flush with standard spreader pipes with fittings, g.i clamps and c.p. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required: single squatting plate with 5 litre p.v.c. automatic flushing cistern(dsr 2023 sh-17.6.1 ) 19 providing and laying flamed finish granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the engineer-in-charge :flamed finish granite stone slab jet black, cherry red, elite brown, cat eye or equivalent.(dsr 2023 sh-11.55.1 ) 20 providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to isi : 12701, colour of opaque white or as approved by engineer-in- charge. the rate includes making necessary holes for inlet, outlet & over flow pipes. the base support i/c fittings & fixtures for tank shall be paid separately 21 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized pvc medium well casing (cm) pipe of required dia, conforming to is: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of engineer -in-charge100 mm nominal size dia 22 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized pvc medium well casing (cm) pipe of required dia, conforming to is: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of engineer -in-charge150 mm nominal size dia 23 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply and all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one stepcpvc solvent cement and testing of joints complete as per direction of engineer in charge. internal work - exposed on wall 15 mm nominal dia pipes 24 providing and fixing ptmt bib cock of approved quality and colour.15mm nominal bore, 86 mm long, weighing not less than 88 gms 25 providing and fixing ptmt stop cock of approved quality and colour.15 mm nominal bore, 86 mm long, weighing not less than 88 gms) 26 mirror of superior make glass 60x45 cm 27 providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete size of tile 600x600 mm 28 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer-in-charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 29 supply and fixing of light fitting switch board. (none sheduled) 30 supply and fixing wiring of light point. (none sheduled) 31 s/l/j of 20mm dia pvc cunduct pipe etc. all complete. 32 supply & fixing of wiring sub main. 33 supply & fixing of plug point 15mm. 34 lettering & painting of wall etc. all complete. 35 supply & fixing of 27watt. cfl etc. all complete. 36 carriage of materials by manual labour including loading, unloading and stacking for lead less than 01-50 mtrm.207.34+30.42 every 50 additonal meter 37 stone tile work for wall lining upto 10 m height with special adhesive over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement with an admixture of pigment to match the stone shade. 7.38.1 8mm thick (mirror polished and machine cut edge) 7.38.1.1 granite stone of any colour and shade 38 constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast r.c.c. horizontal grating with frame complete as per standard design :with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 39 kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick 40 6 mm cement plaster of mix :1:3 (1 cement : 3 fine sand) 41 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.) 42 stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (to be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) :8.14.1 red sand stone - exposed face fine dressed with rough backingt 43 marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with :raj nagar plain 44 providing and fixing stainless steel ( grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)(dsr 2023 sh-10.28 ) 45 1:2:4 (1 cement : 2 coarse sand (zone-iii) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources). (dsr 2023 s h) 46 supply & fixing granite stone work display board (size 2.50ft x 4.00ft) including painting, lettering etc. all complete. (none schedule) 47 sub total 48 add/deduction rs. for estimate figure amount match 49 grand total

State Government

TRN :49020123 | 12 May, 2025

Tender Value : 11.90 Lacs

Sirohi - Rajasthan

Tender for tender for various civil works for garden at government collage, sheoganj- 1 construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of tables 300-1 and 300-2 with a lead upto 50 m as per morth specification clause 305.3 2 surface dressing of the ground including removing vegetation and inequalities not exceeding 15cm deep and disposal of rubbish lead up to 50 mtr. and lift up to 1.5 mtr. : all kinds of soil 3 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - all work up to plinth level. m10 grade nominal mix1: 3: 6 (1 cement : 3 coarse sand : 6 graded stoneaggregate 40mm nominal size). 4 providing and laying 80 mm thick cement concrete blocks of m-40 grade (manufactured with fully mechanised dry cast process with forced action mixer whose arms revolve along the main axis and rotate about its own axis also, having humidity sensor for moisture control of w/c ratio in concrete mix. manufactured with steel moulds(milled and manufactured in csi diamond or csi nitro process for accuracy) on steel base plate of min 16 mm thick;having vibration and pressing action both together withthe help ofmultiple synchronised vibrators.power of hydraulic station should be minimum 50kw for compaction and cured in controlled chambers having humidity control and automated air circulation system) spreading 25mm thick sand underneath and filling joints with sand on existing w.b.m.base, as per is15658:2006 and all mat 5 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcementfor walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.m20 grade nominal mix / design mix 6 kota stone slab flooring 25 mm thick over 20 mm (average) thickbase laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing completewith base of cement mortar 1 : 4 (1 cement : 4 coarse sand) 7 earth work in excavation by mechanical means (hydraulic excavator )/ manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal ofexcavated earth, lead upto 50m andlift upto 1.5 m , disposed earth to be levelled and neatly dressed : all kinds of soil 8 random rubble stone masonry with hard stone in superstructure aboveplinth level and upto five levelabove 30cm. thick walls in : cement mortar 1:6 ( 1-cement : 6-sand). 9 plaster on new surface on wall in cement sand mortar 1:3 including racking of joints etc. complete fine finish : 25 mm thick 10 providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth completenew plastered surface (three or more coats) 11 painting with synthetic enamel paint of approved brand and manufacture togive an even shade :two or more coats on new work 12 providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide 13 finishing walls with acrylic smooth exterior paint of required shade including all scaffolding. new work (two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm ). 14 providing and fixing granite stone slab mirror polished and machine edge cut in walls, pillars, steps, shelves, sills counters, floors etc. laid on 12mm (av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete.

State Government

TRN :49020462 | 15 May, 2025

Tender Value : 0

Akola - Maharashtra

Tender for rate call for ( non dsr) items preparing estimate of under honble balasaheb thackeray haridra research and traning centre,vasmat,dist.hingoli =2 providing & fixing on site 75 mm thick reflexology ( pebbles ) stone flooring etc complete 3 providing & laying of hdpe pond liner of 750 micron thickness as per manufacturer’s specification & instructions from engineer in charge etc. complete. 4 orientation signage pole :- providing & fixing of orientation signage pole made up of marine quality composite {marine grade corrosion resistant & hydrocarbon solvent resistant), with the size of 12x4inner frame and 60mm dia for support structure made of mild steel pipe is:3601 or equivalent, hot-dip galvanized 60 microns, post fabrication. its reinforced with glass fibre cs 1040 450gsm e glass matt with a density of 450g/m2 & 300gsm emulsion chopped strand matt with a density of 300g/m2. the product is an all weather proof & maintenance free with long design life. its self-coloured textured surface finish with scratch resistant, aliphatic grade u.v. stabilized pu paint with uv stable polyurethane 120 s+/-5 viscosity aliphatic paint. with long standing life. these frp pole is individually crafted) which usually require maintenance and care. the structure will be illuminated from within. item is including installation with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site. structural stability certificate will be given etc complete 5 identification signage pole :- providing & installation of identification signage pole made up of marine quality composite from 60mm dia for support structure {marine grade corrosion resistant & hydrocarbon solvent resistant) with all fittings fixture, hardwares , all as per design & drawings with all fittings, fixtures etc. complete , with the size of 6x1.5inner frame made of mild steel pipe od 60mm as the main support section is:3601 or equivalent, hot-dip galvanized 60 microns, post fabrication. its reinforced with glass fibre cs 1040 450gsm e glass matt with a density of 450g/m2 & 300gsm emulsion chopped strand matt with a density of 300g/m2. the product is an all weather proof & maintenance free with long design life. its self-coloured textured surface finish with scratch resistant, aliphatic grade u.v. stabilized pu paint with uv stable polyurethane 120 s+/-5 viscosity aliphatic paint. with long standing life. these frp pole is individually crafted) which usually require maintenance and care. item is including installation with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site. structural stability certificate will be given etc complete 6 directional signage -5m single arm frp pole with haldi banner and leaf (signage): the single arm pole shall be made of 68 mm dia with metal hot dipped galvanized pipe support inside the frp cladded pole. made of marine quality composite {marine grade corrosion resistant & hydrocarbon solvent resistant), inner frame made of is:3601 or equivalent, hotdip galvanized 60 microns, post fabrication. its reinforced with glass fibre cs 1040 450gsm e glass matt with a density of 450g/m2 & 300gsm emulsion chopped strand matt with a density of 300g/m2. the product is an all weather proof & maintenance free with long design life. its self-coloured textured surface finish with scratch resistant, aliphatic grade u.v. stabilized pu paint with uv stable polyurethane 120 s+/-5 viscosity aliphatic paint. with long standing life. these frp pole is individually crafted which usually require maintenance and care. pride suspended luminaire: 50 watt led suspended luminaire with height 450mm and width 500mm. item is including installation with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site. structural stability certificate will be given etc complete 7 directional signage post :-providing & fixing of directional signage post (signage) with 5ft height and 700mm wide post and 48 mm dia support pipe with frame having and metal frame to show the directional or location of certain area. made of marine quality composite {marine grade corrosion resistant & hydrocarbon solvent resistant), inner frame made of mild steel pipe is:3601 or equivalent, hot-dip galvanized 60 microns, post fabrication. its reinforced with glass fibre cs 1040 450gsm e glass matt with a density of 450g/m2 & 300gsm emulsion chopped strand matt with a density of 300g/m2. the product is an all weather proof & maintenance free with long design life. its self-coloured textured surface finish with scratch resistant, aliphatic grade u.v. stabilized pu paint with uv stable polyurethane 120 s+/-5 viscosity aliphatic paint. with long standing life. item is including installation with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer incharge etc. complete on site. structural stability certificate will be givenv 8 haldi information post :- providing & fixing of haldi information post- farming (signage) with 5ft height and 700mm wide and 48 mm dia support pipe with frame having a metal frame work to be used for provided information regarding the harida haldi project and which type of haldi crop grown on the particular field. made of marine quality composite {marine grade corrosion resistant & hydrocarbon solvent resistant), inner frame made of mild steel pipe is:3601 or equivalent, hot-dip galvanized 60 microns, post fabrication. its reinforced with glass fibre cs 1040 450gsm e glass matt with a density of 450g/m2 & 300gsm emulsion chopped strand matt with a density of 300g/m2. the product is an all weather proof & maintenance free with long design life. its self-coloured textured surface finish with scratch resistant, aliphatic grade u.v. stabilized pu paint with uv stable polyurethane 120 s+/-5 viscosity aliphatic paint. with long standing life. these frp pole is individually crafted) which usually require maintenance and care. item is also including installation with all fittings fixture, hardwares , scaffolding, all as per design & drawings & as per instructions from engineer in charge etc. complete on site. structural stability certificate will be given etc complete. 9 pergolas type 1:- providing & fixing of type 1 pergolas with frp column 200mm x 200 mm in ms fabrication use in 88.2 od ms pipe 3 mm thickness. frp beam size 150 mm x 150 mm in ms fabrication 40 mm x 40 mm x 2 mm thickenss tube in framing. frp support for beam and column use in 75 mm x 75 mm x2 mm ms tube with frp cladding. frp thickness minimum 3 to 4 mm . column fittng in 12 mm x 150 mm anchor bolt in foundation. including installation machineries, scaffoldings, electricity, other site utilities in client scope. made of marine quality composite {marine grade corrosion resistant & hydrocarbon solvent resistant), inner frame made of mild steel pipe is:3601 or equivalent, hot-dip galvanized 60 microns, post fabrication. its reinforced with glass fibre cs 1040 450gsm e glass matt with a density of 450g/m2 & 300gsm emulsion chopped strand matt with a density of 300g/m2. the product is an all weather proof & maintenance free with long design life. its self-coloured textured surface finish with scratch resistant, aliphatic grade u.v. stabilized pu paint with uv stable polyurethane 120 s+/-5 viscosity aliphatic paint. with long standing life. item is including installation with all fittings fixture, hardwares , scaffolding, all as per design & drawings & as per instructions from engineer in charge etc. complete on site. structure stability certificate will be provided etc complete 10 pergolas type 2( for seating areas ):- providing & fixing of type 2 with frp column 200mm x 200 mm in ms fabrication use in 88.2 od ms pipe 3 mm thickness . frp beam size 150 mm x 150 mm in ms fabrication 40 mm x 40 mm x 2 mm thickness tube in framing. frp support for beam and column use in 75 mm x 75 mm x2 mm ms tube with frp cladding. frp thickness minimum 3 to 4 mm . column fitting in 12 mm x 150 mm anchor bolt in foundation. including installation machineries, scaffoldings, electricity, other site utilities in client scope. made of marine quality composite {marine grade corrosion resistant & hydrocarbon solvent resistant), inner frame made of mild steel pipe is:3601 or equivalent, hot-dip galvanized 60 microns, post fabrication. its reinforced with glass fibre cs 1040 450gsm e glass matt with a density of 450g/m2 & 300gsm emulsion chopped strand matt with a density of 300g/m2. the product is an all weather proof & maintenance free with long design life. its self-coloured textured surface finish with scratch resistant, aliphatic grade u.v. stabilized pu paint with uv stable polyurethane 120 s+/-5 viscosity aliphatic paint. with long standing life. type 2 (for seating areas ). item is including installation with all fittings fixture, hardwares , scaffolding, all as per design & drawings & as per instructions from engineer in charge etc. complete on site. structure stability certificate will be provided etc complete. 11 providing & fixing of type 01 module ( with back rest) frp seating with pvc wooden panel (1.5m with wooden panel on top) bench should be made in combination of 80 mm dia and 40mm dia pipe marine quality composite (marine grade corrosion resistant & hydrocarbon solvent resistant), 2.4m x 0.45m (module) the product should be an all weather proof & maintenance free with long design life. it should be self colored textured surface finish with scratch resistant, aliphatic grade u.v. stabilized pu paint with uv stable polyurethane 120 s+/-5 viscosity aliphatic paint, with long standing life item is including installation with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site. 12 providing & fixing of type 02 module ( without back rest) frp seating with pvc wooden panel bench should be made in combination of 80 mm dia and 40mm dia pipe marine quality composite (marine grade corrosion resistant & hydrocarbon solvent resistant), 2.4m x 0.45m (module) the product should be an all weather proof & maintenance free with long design life. it should be self coloured textured surface finish with scratch resistant, aliphatic grade u.v. stabilized pu paint with uv stable polyurethane 120 s+/-5 viscosity aliphatic paint, with long standing life . item is including installation with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site. 13 providing & fixing of type 01 module ( with back rest) frp seating with pvc wooden panel (1.5m with wooden panel on top) bench should be made of 80 mm dia and 40mm dia pipe marine quality composite (marine grade corrosion resistant & hydrocarbon solvent resistant), 2.4m x 0.45m (module) the product should be an all weather proof & maintenance free with long design life. it should be self colored textured surface finish with scratch resistant, aliphatic grade u.v. stabilized pu paint with uv stable polyurethane 120 s+/-5 viscosity aliphatic paint, with long standing life. item is including installation with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site. 14 providing & fixing of type 02 module ( without back rest) frp seating with pvc wooden panel (1.5m with wooden panel on top) bench should be made of 80 mm dia and 40mm dia pipe marine quality composite (marine grade corrosion resistant & hydrocarbon solvent resistant), 2.4m x 0.45m (module) the product should be an all weather proof & maintenance free with long design life. it should be self colored textured surface finish with scratch resistant, aliphatic grade u.v. stabilized pu paint with uv stable polyurethane 120 s+/-5 viscosity aliphatic paint, with long standing life. item is including installation with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site. 15 dustbin frp dustbin should be made of marine quality composite (marine grade corrosion resistant & hydrocarbon solvent resistant) all weather proof & maintenance free with long design life. the product should be 700 x 500 frp planter with basic design and 40 x 20mm sq. pipe to support the section of dustbin. it should be selfcolored textured surface finish with scratch resistant, aliphatic grade u.v. stabilized pu paint with uv stable polyurethane 120 s+/-5 viscosity aliphatic paint, with long standing life. the glass fiber reinforced polymer camouflage should be of thickness 3 to 4 mm average with sizes 2000x600 mm. item is including installation with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site. 16 providing & placing at position type1 of 700mm x 305mm frp plantershould be made of marine quality composite (marine grade corrosion resistant & hydrocarbon solvent resistant). the product should be 700 x 305 frp planter with basic design and all weather proof & maintenance free with long design life. it should be self-colored textured surface finish with scratch resistant, aliphatic grade u.v. stabilized pu paint with uv stable polyurethane 120 s+/-5 viscosity aliphatic paint, with long standing life. the glass fiber reinforced polymer camouflage shall be of thickness 3 mm average. product should come with a 12 month warranty against any manufacturing defect etc complete 17 providing & placing at position type2 of 610 mm x 254 mm frp planterfrp planter should be made of marine quality composite (marine grade corrosion resistant & hydrocarbon solvent resistant). the product should 610 x 254 frp planter with basic design and all weather proof & maintenance free with long design life. it should be self-colored textured surface finish with scratch resistant, aliphatic grade u.v. stabilized pu paint with uv stable polyurethane 120 s+/-5 viscosity aliphatic paint, with long standing life. the glass fiber reinforced polymer camouflage should be of thickness 3 mm average. product should come with a 12 month warranty against any manufacturing defect etc complete 18 providing & placing at position type3 of 510 x 200 frp planter frp planter should be made of marine quality composite (marine grade corrosion resistant & hydrocarbon solvent resistant). the product should 510 x 200 frp planter with basic design and all weather proof & maintenance free with long design life. it should be self-colored textured surface finish with scratch resistant, aliphatic grade u.v. stabilized pu paint with uv stable polyurethane 120 s+/-5 viscosity aliphatic paint, with long standing life. the glass fiber reinforced polymer camouflage should be of thickness 3 mm average. product should come with a 12 month warranty against any manufacturing defect etc complete 19 tree grating:- providing & fixing of frp tree grating of size 1100 x 1100 x 25 mm frp material with various design options. made of marine quality composite (marine grade corrosion resistant & hydrocarbon solvent resistant), the product should be an all weather proof & maintenance free with long design life. it should be self-colored textured surface finish with scratch resistant, aliphatic grade u.v. stabilized pu paint with uv stable polyurethane 120 s+/-5 viscosity aliphatic paint, with long standing life. as per design & drawings with all fittings, fixtures etc. complete. item is including installation with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site.. 20 custom design, supply & installation /surfacing of epdm 6 mm & 19 mm rubber crumbs at site etc complete 21 providing & fixing of tumble twin with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site 22 providing & fixing of animal mgr with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site 23 providing & fixing of deluxe junior see saw with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site 24 providing & fixing double post swing with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site etc complete 25 providing & fixing duck rider with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site 26 providing & fixing fun walker single with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site 27 providing & fixing step trainer with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site 28 providing & fixing chest press double with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site 29 providing & fixing shoulder press double with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site 30 providing & fixing tai chi cum standing twister with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site 31 providing & fixing leg press cum parallel bar with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site 32 providing & fixing leg press cum seating twister with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site 33 providing & fixing of cobble stone of basalt 100 mm x 100 mm & 40 to 50mm thick etc complete 34 providing, fixing & installation of 18mm thick grc ( glass reinforcedconcrete ) of high quality iso grade upto 2.4 mtr height with 18mm grc chopped strands includingpure white cement , silica sand for finishingwith coating of sbr liquid or equivalent chemical for bonding work with all fittings, fixtures hardwares, wax polishing, caster, fitter, labour charges, scaffolding etc. complete as per design, drawings & manufacturer’s specification also as per instructions from engineer in charge etc. complete. sbr liquid will be used for bonding of various materials of the structure which also helps in waterproofing and adhesion giving it a long life durability specially multi dies will be made using cnc machine giving it a high precession for the design of the structure. material is made of marine quality composite {marine grade corrosion resistant & hydrocarbon solvent resistant). its reinforced with glass fibre cs 1040 450gsm e glass matt with a density of 450g/m2 & 300gsm emulsion chopped strand matt with a density of 300g/m2. the product is an all weather proof & maintenance free with long design life. its self-coloured textured surface finish with scratch resistant, aliphatic grade u.v. stabilized pu paint with uv stable polyurethane 120 s+/-5 viscosity aliphatic paint. with long standing life including structural stability certificationetc complete. 35 providing, fixing & installation of 4 mm thick frp ( fiber reinforced polymer) material high quality iso grade. frp material placed above grc of high quality iso grade material as per design, drawings & as per manufacturer’s specification & instructions from engineer in chargeincluding all hardener, fittings, fixtures, welder, patch work,labours charges, scaffolding etc. complete . the product is an all weather proof & maintenance free with long design life. its self-coloured textured surface finish with scratch resistant, aliphatic grade u.v. stabilized pu paint with uv stable polyurethane 120 s+/-5 viscosity aliphatic paint. with long standing life including structural stability certification etc complete. 36 providing & applying weather finish coating & lackering of 100microns to all surfaces of grc & frp with all rubbing, finishingwith all equipments, labours, scaffolding all as per design, specification & instructions from engineer in charge etc. complete 37 waterproofing cum insulation composite system:-cleaning the surface to make it dust free andsludge free, removing any extended portions by grinding and if required using suitable equipment’s and should be totally dry & have proper slope for free flow of water preparing the surface by spray applying a coat of bitumen primer @0.25-0.35kg/square metre over the entire dust free surface. providing and applying single layer of ultraplast b app- 4mm (atactic polypropylene polymer) modified water proofing membrane reinforced with non-woven polyester matt 160+20 g/m2 having polymer film as a top surface. minimum tensile strength in longitudinal and transverse direction as 750n +150 / 600n +120/5cm (astm d 5147). minimum nail shank tear resistance in longitudinal and transverse direction as 300/300n + 100 n (astm d 4073) elongation in longitudinal and transverse direction 40+8% / 45+9%. softening point of membrane not less than 150 + 5 degree celsius consisting of a coat of technonicol bitumen primer no 01 primer @ 0.25- 0.35 ltr./sq.mtr with a relative viscosity of 15-40 s,. over the primer coat, the layer of membrane shall be laid using butane / lpg torch and sealing all joints with minimum 75 mm side laps & 100 mm end laps to form a monolithic system. the laying of membrane shall be got done through the authorized applicator of the manufacturer of membrane etc complete. 38 providing and laying leed certified carbon prof 300 extruded polystyrene 50mm thick having thermal conductivity of 0.028 w/mk (astm c 177) with compressive strength of > 300 kpa (astm d 1621 en 826) and density of 30-35 kg/m3. long term water immersion astm c 272 (en12087) < 0.7% over the waterproofing membrane having shiplap arrangement. work shall be done through the authorized applicator of the manufacturer of the insulation boardetc complete. 39 prviding & fixing glassreinforced concrete (grc)25mm jali as per deign & details etc completed. 40 providing and fixing heavy gauge galvinsed iron 50”fan with autoopening 10shutters, drop hamper exhaust fan systems with 6 no.ss blades with low noise , cfm:-25890, auto opening shutters damper type 415v,50hz, 1.5hp motor, 3hp with fitting etc complete.cellulose cooling pad 1200mmx600mmx100mmt one pad contain area of 1 0 sqft, leading kit with pipeline upto frame,- bypass, filter flush system etc.6”aluminum frame for the above coolingpads with top water distribution and bottom gutter, aluminum 41 providing & fixing air circulation fans 7 blades ss aluminum powder coated of model gtacf-40-70, size of d320mmxh400, 50hz , 1400 rpm, 220v, 120w, single phase, 70 ft airflow etccomplete. 42 automatictemp humidity controller- providing & fixing microprocessor based temp & humidity controller excluding moisture sensors, electrical control panel for fan,cooling pad, pump, mcb, contractor, olr, auto manual switching on/of fswitches ip55 cabinet, electrical cable 1 .5sqmm 4core for fans and pads,sensor cable 4core 0.5square mm etc complete. 43 providing & fixing controller - plc & hmi based control, drip valves control -2 nos,dosing valves control- 3nos ( a-b,c-acid), filling pump, system pump, air pump control, mixing valve control, phase missing prevention, over current prevention control, operation modes: auto -manual-bypass. 44 providing & fixing dosing unit includes dosing channels - 3nos @400lph with flow indicatiors & regulators, dosing valves - 3 nos (a-b,c-acid ), system pump - 30klph@35m head- ss 316 grade, dosing line filters-3nos 45 providing & fixing flow sensor of 3” as per design & drawing etc complete. 46 providing & fixing regenerative air blower-385cfm for 2 stocks mixing as per design & drawing etc complete. 47 providing & fixing solenoid valvesof 2” as per design & drawing etc complete. 48 providing & fixing exhaust fans -1.5hp 3phase- 16 nos4 controls ( each control 4 fans) pad pump - 3hp, 3phase- 1no fogging pump-5hp- 1no acf- 0.5hp- 1phase- 32nos - 1 control (3 phase load distribution) temperature sensor - 1no etc complete. 49 providing & fixing pressure release valves of 2” as per design & drawing etc complete. 50 providing & fixing total galvinsed iron structure of column pipes, profile, zig-zag spring, locking, perlins, tie bar, cross, gutter purlin, hockey , hockey memeber, hockey runner, nagarpatta, galvinsed gutter sheet, l, f brcackets, clamps, bolts , nuts, self drilling screw, spring, sliding pulley, netring, curtain clamps, door cup, handle, fiber door, hole pass. above all incudes, complete structure- erection, fixing etc complete. 51 poviding & fixingpoly film, 50% shade net, 30% side net with 6.5m center height,d rain out, israel make ginegar diffuse 200micron. above all incudes, making foundation, completestructure- erection, fixing etc complete. 52 providing & fixing high-tech irrigation system including inline drip lateral, inside main and sub main pvc pipes, fogger system, sand filter, disc-filter, ventury system with instillation & testing. 3024 sqm etc complete. 53 providing &fixingweed control mat 3000 sq mtr 120 gsm as per design & drawing etc completed. 54 providing &fixingplastic trough20:50:20500 micron 6000 running mtr etc complete. 55 providing & supplying low electrical conductivity coco-peat as instructed etc complete. 56 constructing stormwater channel with (random rubble masonary) rrm stone masonry in cement mortar 1:5foundation concrete 1:3:6 mix, raking rrm joints and cement grouting as perstandard design including excavation refilling anddisposalof surplus earth, providing and securely fixing ci frame in rrm and ci grating (heavy duty) etc. complete. (ci grating and frame make: neco or equivalent) 300mm wide channel, 300mm deep at start with 1:200 slope, heavy duty ci grating and frame etc complete 57 constructing stormwater channel with (random rubble masonary) rrm stone masonry in cement mortar 1:5foundation concrete 1:3:6 mix, raking rrm joints and cement grouting as perstandard design including excavation refilling anddisposalof surplus earth, providing and securely fixing ci frame in rrm and ci grating (heavy duty) etc. complete. (ci grating and frame make: neco or equivalent) 600mm wide channel, 300mm deep at start with 1:200 slope, heavy duty ci grating and frame etc complete 58 constructing stormwater channel with (random rubble masonary) rrm stone masonry in cement mortar 1:5foundation concrete 1:3:6 mix, raking rrm joints and cement grouting as perstandard design including excavation refilling anddisposalof surplus earth, providing and securely fixing ci frame in rrm and ci grating (heavy duty) etc. complete. (ci grating and frame make: neco or equivalent) 900mm wide channel, 300mm deep at start with 1:200 slope, heavy duty ci grating and frame etc complete 59 constructing stormwater channel with (random rubble masonary) rrm stone masonry in cement mortar 1:5foundation concrete 1:3:6 mix, raking rrm joints and cement grouting as perstandard design including excavation refilling anddisposalof surplus earth, providing and securely fixing ci frame in rrm and ci grating (heavy duty) etc. complete. (ci grating and frame make: neco or equivalent) 1200mm wide channel, 300mm deep at start with 1:200 slope, heavy duty ci grating and frameetc complete 60 supply, installation, testing, and commissioning of the electrical trench, with dimensions of 1300mm length, 1300mm width, and 1300mm depth, which includes a cover at every 15-meter interval, and also includes all necessary civil work to complete the electrical trenchetc complete 61 providing and fixing of ‘seamless gloss’ tiles of himalyan acoustics / baux / baswa or equivalent20mm thick with square edge made of gloss base panel (non-magnisite) with wood fibre 1mm width cement composites covered with acoustically transparent absorptive microfibers on the front side pasted on site with sprayable glue and colour as per the choice of the architect/ person in charge with seamless finish. has excellent noise absorption of 0.85 nrc as per iso: 354-1985 and astm 423-90 a, stc of 47 as per astm e90/413 for 25mm, density 400 kg/ m3, meets stringent fire ratings astm d- 876 and bs:476 , weather resistance as per is 3308, thermal insulation as per is:3346-1980 with relative humidity of 90% rh at 60o celcius(140o farenhite) for 15 days= no deterioration. conforms to en 131682001 and are rohs complaint and anti-bacterial test as per jis-z2801-2010.to be installed on g.i studs 600x600mm centre to centre 2400mm x 50mm web thickness 0.5mm, flanges 15 & 50mm fully knurled giving it high strength, hot dipped galvanized steel with 120gsm zinc coating specially designed for acoustic vibration management and long life with a backing of 50mm thick,1000 gsm absorb wool tested as per fire retardant astmd 635-1991/insulation and is 15061-2002 for excellent results( ceiling absorption nrc 0.85) etccomplete. 62 providing fibrette doodle 20 ceiling tiles of himalyan acoustics / baux / baswa or equivalent made of wood fibre cement composites with an option of colours as per the choice of the architect/ person in charge of size 1200 x 600 mm highly recommend for walls / ceilings. has excellent noise absorption of 1 nrc as per iso: 354-1985 and astm 423-90 a, density 400 kg/ m3, meets stringent fire ratings astmd-876 and fire class -1 and class p-not easily ignitable as per bs-476-part 5,6,7, weather resistance as per is 3308, thermal insulation as per is:3346-1980 with relative humidity of 90% rh at 60° celsius (140° fahrenheit) for 15 days= no deterioration. tested as per en 131682001 and are rohs complaint. to be installed on g.i studs 600x600mm centre to centre2400mm x 50mm web thickness 0.5mm, flanges 15 & 50mm fully knurled giving it high strength, hot dippedgalvanized steel with 120gsm zinc coating specially designed for acoustic vibration management and long life witha backing of himalyan acoustics 50mm thick,1000 gsm absorb wool tested as per fire retardant astmd 635-1991/insulation and is 15061-2002 for excellent results(ceiling absorption nrc 1 ) etc complete 63 providing and fixing of ‘seamless gloss’ tilesof himalyan acoustics / baux / baswa or equivalent wth 20 mm thick with square edge made of gloss base panel (non-magnisite) with wood fibre 1mm width cement composites covered with acoustically transparent absorptive microfibers on the front side pasted on site with sprayable glue and colour as per the choice of the architect/ person in charge with seamless finish. has excellent noise absorption of 0.85 nrc as per iso: 354-1985 and astm 423-90 a, stc of 47 as per astm e90/413 for 25mm, density 400 kg/ m3, meets stringent fire ratings astm d- 876 and bs:476 , weather resistance as per is 3308, thermal insulation as per is:3346-1980 with relative humidity of 90% rh at 60o celcius(140o farenhite) for 15 days= no deterioration. conforms to en 131682001 and are rohs complaint and anti-bacterial test as per jis-z2801-2010.to be installed on g.i studs 600x600mm centre to centre 2400mm x 50mm web thickness 0.5mm, flanges 15 & 50mm fully knurled giving it high strength, hot dipped galvanized steel with 120gsm zinc coating specially designed for acoustic vibration management and long life with a backing of 50mm thick,1000 gsm absorb wool tested as per fire retardant astmd 635-1991/insulation and is 15061-2002 for excellent results (ceiling absorption nrc 0.9 )etc complete. 64 providing wooden micro perforated fr grades 600x600 / 600x1200 16mm made of mdf backed with acouscal fleece providing sound absorpon of abs. coeff. 0.92 @125hz as per (equivalent to iso: 354-1985 & astm 423-90).to be installed with hidden aluminium profile conforms to aluminium alloy 6063-t6.temper as per bs:1474-1987. the density per panel is 750-800 kg/m3. these panel are made from acouscal fibreboard with linear perforaons for excellent uniformity. the perpendicular holes areavailable on the panel. wooden micro perforated can be installed on g.i studs 600x600mm centre to centre 2400mm x 50mm web thickness 0.5mm, flanges 15 & 50mm fully knurled giving it high strength, hot dipped galvanized steel with 120gsm zinc coating specially designed for acoustic vibration management and long life with a backing of 50mm thick,1000 gsm acousc wool tested as per fire retardant astmd 635- 1991/insulation and is 15061-2002 for excellent result wall treatment upto 8ft height etc completeof himalyan acoustics / baux / baswa or equivalent etc complete. 65 providing and fixing ‘aphony cortex’ splendortiles made of wood fibre 1mm widthcement composites 25 mm thick (non magnesite bonded) and covered with acoustically transparent woven fabric on the front side, with an option of colours as per the choice of the architect/ person in charge of size 1200x600/ 600x600 mm.providing sound absorption of 1 nrc as per iso:354-1985 and astm 423-90 a, stc of 49 as per astm e90/413 meets the stringent fire ratings astmd- 876 and bs:476, weather resistant as per is 3308 thermal conditivity result 45 w/m2/kas per is:3346-1980. conforms to en 131682001.to be installed with pvc h profile on g.i studs600x600mm centre to centre 2400mm x 50mm web thickness 0.5mm, flanges 15 & 50mm fully knurled giving ithigh strength, hot dipped galvanized steel with 120gsm zinc coating specially designed for acoustic vibration management and long life with a backing of himalyan acoustics. 50mm thick,1000 gsm absorb wool tested as per fire retardant astmd 635-1991/insulation and is 15061-2002 thermal conductivity test , w/mk , as per astm c 518 test result ( sc-6490) -0.03312for excellent results.wall absorption nrc 1 etc complete. 66 providing fibrette doodle 25mm walls himalyan acoustics / baux / baswatiles made of wood fibre cement composites with an option of colours as per the choice of the architect/ person in charge of size 1200 x 600 mm highly recommend for walls / ceilings. has excellent noise absorption of 1 nrc as per iso: 354-1985 and astm 423-90 a, density 400 kg/ m3, meets stringent fire ratings astmd-876 and fire class -1 and class p-not easily ignitable as per bs-476-part 5,6,7, weather resistance as per is 3308, thermal insulation as per is:3346-1980 with relative humidity of 90% rh at 60° celsius (140° fahrenheit) for 15 days= no deterioration. tested as per en 131682001 and are rohs complaint. to be installed on g.i studs 600x600mm centre to centre2400mm x 50mm web thickness 0.5mm, flanges 15 & 50mm fully knurled giving it high strength, hot dippedgalvanized steel with 120gsm zinc coating specially designed for acoustic vibration management and long life witha backing of himalyan acoustics 50mm thick,1000 gsm absorb wool tested as per fire retardant astmd 635-1991/insulation and is 15061-2002 for excellent results wall absorption nrc 1 etc complete. 67 providing and fixing ‘aphony fibril’ tiles20 mm with himalyan acoustics / baux / baswa or equivalenttaper edge made of compressed wood fibre made with (non-magnesite bonded) inorganic compound with mat blackcolour of size 600x1200/600x600mm. has excellent noise absorption of 0.70 nrc as per iso: 354-1985 and astm 423-90 a, stc of 48 as per astm 90/413 density 650-750 kg/ m3, meets stringent fire ratings astm d- 876 and bs:476 , tested as per astm c 367-99 to be installed on g.i studs 600x600mm centre to centre 2400mm x 50mm web thickness 0.5mm, flanges 15 & 50mm fully knurled giving ithigh strength, hot dipped galvanized steel with 120gsm zinc coating specially designed for acoustic vibration management and long life with a backing of himalyan acoustics. 50mm thick,1000 gsm absorb wool tested as per fire retardant astmd 635-1991/insulation and is 15061-2002for excellent results.make etc complete. 68 providingfloor carpet ofhimalyan acoustics / baux / baswa or equivalent with specification : weight :875 dynamic loading ( bs 4052)nominal thickness ( mm): 4.00color fastness tested as per.is 5641wash ( is 11969)light ( is 0686)flammability test ( is 5641) etc complete. 69 providing and fixing of acoustic door ofhimalyan acoustics / topakustik / baswa or equivalent of 56 mm having an stc rating upto 59.6 @ 100 hz as per iso:140/astm90/413. the door will be filled with high acoustic materials of 2 layers of 8 mm water proof acoustic ply with dampner sheet, 2 layers of 10mm thick absorb wool 300 gsm, sound dampner 12mm 1218x1218 mm made of 10 mm compressed wood cement composites 1250kg/m3 and 2mm dampner sheet 37 stc as per iso 140 (part-iii) - 1995. final finish with teak ply 4mm thick interior and exterior side. door frame will be made of teak wood teak wood/ engineered wood. frame on all four sides or three sides frame and drop seal below will be provided along with the door. high load bearing hinges will be provided along. fr tested as per is:3614 (pt. ii) & bs: 476-(pt.20 & 22). 70 providing and fixing of teak wooden flooring of himalyan acoustics / baux / baswa or equivalent of20mm thickness with polish. teak wooden flooring with tongue and groove system with size 510x90x20mm. termite treated seasoned. to be installed on ply board 16mm.floor polish charges included etc complete. 71 supply & installation of auditorium tip-up chairs:seat to be mounted on center pedestal 75mm x 100mm mounted on ms plate 200mm x 200mm x 6mm thickness. seat & contoured back made in cold injection moulded pu foam of density of 60kg/m3 and 46kg/m3 respectively over metal structure.19 0colored cushion (fabric colour to clients choice) with removable seat cover.seat and backrest frames are made out of metal frame structure black powder coated.upholstered back to with multi angle adjustable mechanism upto 30 degrees inclination.counterweight silent/noiseless tip up seat mechanism, seat shall be able to be removed easily for cleaning and maintenance without the need of any tools. solid armrests laminate finished (wooden appearance) seat number in oval acrylic and row number in metal plate, with provision for wiring to put led illumination. strength & durability of seat to comply to en12727: 2016 for level 4 load test.fire resistance to meet bs5852 & bs 7176warranty 5 years. price inclusive of transportation with all leads and lifts etc, complete. 72 statue- balasaheb thakreproviding statue of 15 ft height in 1st quality fiber material with metal armature (jindal). with internal structure pipe 100mm dia pipe welded together with support pipe in between and arm also with the same pipe of size 1mtr-0.5 mtr the overall height would be 3.5mt from ground. item is including installation with all fittings fixture, hardwares , scaffolding, all as per design & drawings & as per instructions from engineer in charge etc. complete on site. material made of marine quality composite {marine grade corrosion resistant & hydrocarbon solvent resistant), inner frame made of mild steel pipe is:3601 or equivalent, hot-dip galvanized 60 microns, post fabrication. its reinforced with glass fibre cs 1040 450gsm e glass matt with a density of 450g/m2 & 300gsm emulsion chopped strand matt with a density of 300g/m2. the product is an all weather proof & maintenance free with long design life. its self-coloured textured surface finish with scratch resistant, aliphatic grade u.v. stabilized pu paint with uv stable polyurethane 120 s+/-5 viscosity aliphatic paint. with long standing life. structural stability certificate will be given. 73 sculpture-1 man sitting providing & fixing made of frp material as per 3 to 5 ft heights as per design & drawings with combination of 48 mm and 26mm dia pipe and cage work made up of metal path with 20-25 thickness width made of metal support inside and above marine quality composite {marine grade corrosion resistant & hydrocarbon solvent resistant), inner frame made of mild steel pipe is:3601 or equivalent, hot-dip galvanized 60 microns, post fabrication. item is including installation with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site. its reinforced with glass fibre cs 1040 450gsm e glass matt with a density of 450g/m2 & 300gsm emulsion chopped strand matt with a density of 300g/m2. the product is an all weather proof & maintenance free with long design life. its self-coloured textured surface finish with scratch resistant, aliphatic grade u.v. stabilized pu paint with uv stable polyurethane 120 s+/-5 viscosity aliphatic paint. with long standing life. require maintenance and care. 74 sculpture 2 man with hammer sculpture providing & fixing made of frp material as per 3 to 5 ft heights as per design & drawings with combination of 48 mm and 26mm dia pipe and cage work made up of metal path with 20-25 thickness width made of metal support inside and above marine quality composite {marine grade corrosion resistant & hydrocarbon solvent resistant), inner frame made of mild steel pipe is:3601 or equivalent, hot-dip galvanized 60 microns, post fabrication. item is including installation with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site. its reinforced with glass fibre cs 1040 450gsm e glass matt with a density of 450g/m2 & 300gsm emulsion chopped strand matt with a density of 300g/m2. the product is an all weather proof & maintenance free with long design life. its self-coloured textured surface finish with scratch resistant, aliphatic grade u.v. stabilized pu paint with uv stable polyurethane 120 s+/-5 viscosity aliphatic paint. with long standing life. require maintenance and care. 75 sculpture 3 women standing- sculpture providing & fixing made of frp material as per 3 to 5 ft heights as per design & drawings with combination of 48 mm and 26mm dia pipe and cage work made up of metal path with 20-25 thickness width made of metal support inside and above marine quality composite {marine grade corrosion resistant & hydrocarbon solvent resistant), inner frame made of mild steel pipe is:3601 or equivalent, hot-dip galvanized 60 microns, post fabrication. item is including installation with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site. its reinforced with glass fibre cs 1040 450gsm e glass matt with a density of 450g/m2 & 300gsm emulsion chopped strand matt with a density of 300g/m2. the product is an all weather proof & maintenance free with long design life. its self-coloured textured surface finish with scratch resistant, aliphatic grade u.v. stabilized pu paint with uv stable polyurethane 120 s+/-5 viscosity aliphatic paint. with long standing life. require maintenance and care 76 sculpture 4 buffalo- sculpture providing & fixing made of frp material as per 3 to 5 ft heights as per design & drawings with combination of 48 mm and 26mm dia pipe and cage work made up of metal path with 20-25 thickness width made of metal support inside and above marine quality composite {marine grade corrosion resistant & hydrocarbon solvent resistant), inner frame made of mild steel pipe is:3601 or equivalent, hot-dip galvanized 60 microns, post fabrication. item is including installation with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site. its reinforced with glass fibre cs 1040 450gsm e glass matt with a density of 450g/m2 & 300gsm emulsion chopped strand matt with a density of 300g/m2. the product is an all weather proof & maintenance free with long design life. its self-coloured textured surface finish with scratch resistant, aliphatic grade u.v. stabilized pu paint with uv stable polyurethane 120 s+/-5 viscosity aliphatic paint. with long standing life. require maintenance and care. 77 sculpture-5:- man with calf and calf sculpture -providing & fixing made of frp material as per 3 to 5 ft heights as per design & drawings with combination of 48 mm and 26mm dia pipe and cage work made up of metal path with 20-25 thickness width made of metal support inside and above marine quality composite {marine grade corrosion resistant & hydrocarbon solvent resistant), inner frame made of mild steel pipe is:3601 or equivalent, hot-dip galvanized 60 microns, post fabrication. item is including installation with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site. its reinforced with glass fibre cs 1040 450gsm e glass matt with a density of 450g/m2 & 300gsm emulsion chopped strand matt with a density of 300g/m2. the product is an all weather proof & maintenance free with long design life. its self-coloured textured surface finish with scratch resistant, aliphatic grade u.v. stabilized pu paint with uv stable polyurethane 120 s+/-5 viscosity aliphatic paint. with long standing life. require maintenance and care. 78 sculpture-6:- man standing sculpture providing & fixing made of frp material as per 3 to 5 ft heights as per design & drawings with combination of 48 mm and 26mm dia pipe and cage work made up of metal path with 20-25 thickness width made of metal support inside and above marine quality composite {marine grade corrosion resistant & hydrocarbon solvent resistant), inner frame made of mild steel pipe is:3601 or equivalent, hot-dip galvanized 60 microns, post fabrication. item is including installation with all fittings fixture, hardwares , all as per design & drawings & as per instructions from engineer in charge etc. complete on site. its reinforced with glass fibre cs 1040 450gsm e glass matt with a density of 450g/m2 & 300gsm emulsion chopped strand matt with a density of 300g/m2. the product is an all weather proof & maintenance free with long design life. its self-coloured textured surface finish with scratch resistant, aliphatic grade u.v. stabilized pu paint with uv stable polyurethane 120 s+/-5 viscosity aliphatic paint. with long standing life. require maintenance and care. 79 selfie point i love haldi providing & fixing of 2.8m x 2.8 m with height of 2.8m. frp kiosk. made of frp material with dark wood finish. frp dustbin included in the kiosk. made of marine quality composite {marine grade corrosion resistant & hydrocarbon solvent resistant), inner frame made of mild steel pipe is:3601 or equivalent, hot-dip galvanized 60 microns, post fabrication. its reinforced with glass fibre cs 1040 450gsm e glass matt with a density of 450g/m2 & 300gsm emulsion chopped strand matt with a density of 300g/m2. the product is an all weather proof & maintenance free with long design life. its self-coloured textured surface finish with scratch resistant, aliphatic grade u.v. stabilized pu paint with uv stable polyurethane 120 s+/-5viscosity aliphatic paint. with long standing life. item is including placing, installation with all fittings, fixture, hardwares , all as per design, drawings & as per instructions from engineer in charge etc. complete on site.

Government Departments

TRN :49021952 | 15 May, 2025

Tender Value : 0

Rajnandgaon - Chhattisgarh

Tender for nit-60 defect liability works under mmgsvy pkg.no. mmgsy-bmr-dlp-01 in dist. bemetara-cutting of branches of trees shrubs and trimming of grass and weeds. trimming of grass and weeds from the shoulders/berms and disposing off the same to suitable locations as per technical specifications clause 1914 restoration of rain cuts restoration of rain cuts with soil, moorum gravel or a mixture of these, clearing the loose soil, benching for 300mm width laying fresh material in layers not exceeding 250 mm and compaction with plate compactor or power rammer to restore the original alignment, level and slopes as per drawings and technical specifications clause 1902 maintenance of shoulder (filling with fresh selected material)making up loss of material/irregularities on shoulders to the design level by adding fresh approved selected material and compacting it with appropriate equipment at omc upto a lead of 1000 m as per technical specification clause 1903 maintenance of shoulder (filling with fresh selected material)making up loss of material/irregularities on shoulders to the design level by adding fresh approved selected material and compacting it with appropriate equipment at omc upto a lead of 1000 m as per technical specification clause 1903 maintenance of wbm road including filling up of pot holes, ruts and rectifying corrugated surface, damaged edges and raveling as per technical specification clause 1906. prime coat providing and applying primer coat with bitumen emulsion (ss-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per technical specification clause 502 tack coat providing and applying tack coat with bitumen emulsion (rs-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with hydraulic broom as per technical specification clause 503. 20mm thick open-graded premix carpet using bituminous (vg/modified bitumen) binder providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of aggregate 13.2mm size (passing 22.4mm size sieve & retained on 11.2mm sieve and 11.2mm size (passing 13.2mm sieve and retained on 5.6mm sieve) either using penetration grade/ vg bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kn static roller capacity, finished to required level and grades to be followed by seal coat of either type a or type b or type c as per technical specification clause 508., viscocity grade (vg) bitumen specification as per is 73:2006 seal coat providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using type a, type b and type c as per technical specification clause 510, viscocity grade (vg) bitumen specification as per is 73:2006 maintenance of road signs maintenance of road signs by way of cleaning and repainting of mandatory/ requlatory / cautionary/ informatory and place identifications sign board as perdrawing and technical specification clause 1910. providing and fixing of typical pmgsy informatory sign board with logo as per mord specifications and drawing. three ms plates of 1.6 mm thick, top and middle plate duly welded with ms flat iron 25mm x 5m size on back on edges. the lower plate will be welded with ms angle iron frame of 25mm x 25mm x 5mm. the angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 swg sheet tubes posts duly embedded in cement concrete m-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. the top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 swg steel plate tube. all m.s. will be stove enameled on both sides. lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. all sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing clause 1701 and annexure 1700.1 cautionary, mandatory, informatory direction and place identification sign boards.semi-reflective traffic signs upto 0.90 sqmdirection and place identification signs up to 0.9 sqm size boardproviding and erecting direction and place identifications of semi reflective sign boards as per irc:67 made of 2 mm thick m.s. sheet duly stove enameled paint in white colour in front and grey colour on back with red reflective border of 70 mm width and required message, letters, figures with reflective engineering grade tape as per mord specifications of required shade and colour. supported and welded on 47 mm x 47mm of 12 swg square tube of 3050 mm height duly strengthened by 25 mm x 5 mm m/s flat iron on edges on back firmly fixed to the ground by means of properly designed foundations with m-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and technical specification clause 1701 reinforced cement concrete m15 grade kilometre stone/local stone of standard design as per irc:8 fixing in position including painting and printing, etc as per drawing and technical specification clause 1703 5th kilometre stone (precast) ordinary kilometer stone (precast) 200 m stone (precast) maintenance of culverts maintenance of hume pipe culvert by way of clearing, cleaning,erosion repair, repairs to cracks, parapet wall and protection work as per drawing and technical specification clause 1908. maintenance of culverts slab type maintenance of slab type culverts by way of clearing, cleaning,erosion repair, repairs to cracks, parapet wall and protection work as per drawing and technical specification clause 1908. white washing two coats on parapet walls of cd and tree trunks including preparation of surface by cleaning scraping etc. as per technical specifications clause 1915 backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification clause 1204.3.8i. granular material

corporations/Associations/Others

TRN :49022887 | 29 May, 2025

Tender Value : 2.62 Crore

Jagdishpur - Uttar Pradesh

Tender for annual maintenance works at i.a. jagdishpur distt. amethi. - providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at omc in mechanical mix plant carriage of mixed material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density. 2 providing and applying primer coat with bitumen emulsion/ vg-10 on prepared surface of granular base including clearing of road surface and spraying primer at the rate of 0.60 kg/sqm using mechanical means.including supply of all materials, labour and t&p etc. required for proper completion of the work. 3 providing and laying densed gradded bituminous macadam with 100-120 tph hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading premixed with bituminous binder @ 4.50% by weight of total mix and filler, transporting the hot mix material to work site, laying with a hydrostatic paver finisher with sensor control to the required grede,level and alignment,rolling with smooth wheeled,vibratory and tandem rollers to achieve the desired compaction as per mort&h specificationsclauses507 complete work in all respects. including supply of all materials,labour,t&p etc as required for proper completion of the work. 4 providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom.including supply of all materials, labour and t&p etc. required for proper completion of the work. 5 providing and laying 25mm thickbituminous concrete with higher capacity batch typehot mix plant using crushed aggregates of specified grading premixed with bituminous binder @ 5.20 % percent of mix and filler ,transporting the hot mix material to work site , laying with hydrostatic paver finisher with sensor control to the required grade ,level and alignment ,rolling with smooth wheeled , vibratory and tandem roller , to achieve the desired compaction as per mort&h.. specification clause no - 507, complete in all respect. ( grading -i ) 6 road marking with hot applied thermoplastic compound with reflectoringmglass beads on bituminous surface,providing and laying of hot applied thermoplastic compound 2.50mm thick including reflectoring glass beads @ 250 gms per sqm area, thickness of 2.50mm is exclusive of surface applied glass beads as per irc :35.the finished surface to be level uniform and free from streaks and holes. rate as per uppwd. 7 earth work in excavation by mechanical means/manual means over areas including getting out and disposal of excavated earth lead upto 50m and for all lift for all kinds of soil. 8 m-150 brick workin foundation and plinth in cement mortar 1:6 with cement and coarse sand. 9 12 mm thick cement plaster of mortar 1:4 with cement and coarse sand on brick work. 10 providing & laying in position cement concrete of grade 1:5:10 with cement, coarse sand and 40 mm grade stone aggregates. 11 providing and laying 80 mm thick factory made chamfered edge cement concrete paver blocks of m-35 grade with approved colour, design and pattern ,thickness & size / shape complete item no 16.91.2 12 m-150 brick workin plinth and foundation with cement mortar 1:4 with cement and coarse sand. 13 providing and fixing concrete 1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size)on culvert parapet as per standard design,including finishing smooth with cement mortar . 14 finishing walls with water proof cement paint of approved make and quality on new work with 2 coats to give an even shadeincluding supply of all materials, labour and t&p etc. required for proper completion of the work. on culvert parapet 15 repairing of 110 mm dia water supply line leakages including cost of earth work excavation, bailing out water,supply of pipe, d-joint ,nut bolts and specials etc.as required at site condition complete sa per direction of engineer in-charge. 16 repairing of 160 mm dia water supply line leakages including cost of earth work excavation, bailing out water,supply of pipe, d-joint ,nut bolts and specials etc.as required at site condition complete sa per direction of engineer in-charge. 17 providing and laying of 100 mm dia pvc pipe as per code specifications including cost of all material ,specials, excavation of earth work,all labour t&p etc ,testing of pipe line as per requirement complete 18 providing and laying of 150 mm dia pvc pipe as per code specifications including cost of all material ,specials, excavation of earth work,all labour t&petc,testing of pipe line as per requirement complete 19 repairing and rewinding of motor,repairing of pump accessories complete including cost of all material,labour ,t&p etc as required at site condition also including lowering & lifting of motor pump from tubewell boring testing complete. 20 repairing of electric control panel 21 manual sweeping ,garbage/litter collection and removal of animal carcasses etc in all streets,main and arterial roads all street and roadsurfaces, footpaths, pavements, parking, lots, foot, overbridges, busshelters, roadmedians, traffic islands and any other open public areas and structures outing. 22 cleaning & removal of garbage, litter, silt or any blockages from the street side, shallow surface drains(other than under ground sewerage and under ground drains) including tractor with trolly, its pol & driver, 2 nos helper for loading/unloading of garbage, etc . complete item as per direction of engineer in charge. 23 desilting of drain in foul position (work frequency every week ) including disposal of silt/waste out side of industrial area as per direction of engineer in charge. 24 clearing jungle i/c uprooting of rank vegetations, grass, bush, wood trees and saplings of girth upto 30cm measured at a height of 1m above ground level & removal of rubbish upto 50m.

State Government

TRN :49023008 | 15 May, 2025

Tender Value : 97.85 Lacs

Gautam Buddha Nagar - Uttar Pradesh

Tender for tender for landscaping of park p-1 sector -28 with two year maintenance yeida. wc-h - clearing grass and removal of the rubbish up to a distance of 50 m out side the periphery of the area cleared. 2 ploughing the existing ground to a depth of 15cm to 25cm and watering the same . 3 rough dressing the trenched ground including breaking clods. 4 uprooting weeds from the trenched area after 10 to 15days of its foolding with water including disposal of uprooted vegetation. 5 fine dressing of the ground. 6 digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ration of 2:1 by volume ( part of stacked volume of earth afte reduction by 20% : 1 part of stacked volume of manure after reduction by 8% ) follding with water dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) 7 holes 60cm dia, and 60cm deep 8 holes 45cm dia and 45cm deep 9 supplying of chlorpyriphos 20% e.c/ lindane 20% e.c for anti termite treatment of plants @ 2ml./plant and in the interval 1 month up to one year i.e, 12 times in a year hence it comes 24ml/plant or 0.024ltr/plant. 10 supply and stacking of well decayed cattle manure at site including roylty and carriagge up to 5km lead complete. ( cattle manure measured in stacks will reduced by 8% for payment) 11 spreading sludge dump manure and/ or good earth in required thickness as per direction of officer in charge ( cost of sludge, dump manure and/ or directed by the officer in charge. 12 mixing earth and sludge or manure in the required proportion specified or directed by the officer in charge. 13 supply and stacking of selection no. 1/doob grass at site fresh & free from weeds having proper roots in green including loading, unloading carriage and all taxes paid etc. and as per direction of officer in charge. 14 grassing with selection no. 1/ doob grasss including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn, free from weeds and fit for mowing including supplying good earth, if needed ( the grass and good earth shal be paid for separately). 15 preparation of beds for hedging and shurbbery by excavation 60 cm deep and trenching the excavated base to a further depth of 30cm, fefilling the excavated earth after breaking clods and mixing with sludge or mnaure in the ratio of 8:1 (part of stacked volume of earth after reductin by 20% : one part of stacked volume of sludge or manure after reduction by 8% ), flooding with water, filling with earth if necessary watering ad finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as derected within a lead of 50m lift up to 1.5m complete (cost of sludge, manure or extra a lead of 50m, lift up to 1.5m complete (cost of sludge, manure or extra earth to be paid for separately) 16 providing and stacking of duranta golden having ht. 15 to 20cm bushty shape with fresh and healthy leaves in 15cm size of earthen pot/plastic pot & as per direction of the officer in charge. (dsr-18, 6.12pg. no.153) 17 providing and stacking of fucus panda golden of height 45-60cm with 6-7 branches and healthy foliage in p.bag of size 25cm as per direction of the officer in charge. (dsr-18, 8.27pg. no.175) 18 supply of gypsm well packed at site in bags. 19 supply of dap at site in printed plasic bags. (market rate.) 20 supply & planting of plants common varieties as required by engineering incharge in 5 kg poly bags or earthen pots ( not below than 8-10 ) well branched and fully foliage branching dia 0.75 to 1.00mtr. free from disease at site i/c stacking with bamboos(chakresia, site ashok, kusum, gulmohar, amaltash) 21 providing and displaying ficus retusa topiary wall developed with fresh and healthy 5 to 6 big ball spedific size and shape 180 cm to 210cm g in 40cm cement potas per direction of the officer in charge (dsr-18, 5.24 pg. no. 145) 22 providing and stacking of bottle palm of ht. 270-300cm bottom girth 30-35cm well developed in big hdpe bags 23 supply & planting of shrubs plants height 2-2.5 feet as required by engineering incharge in 6x8 polythene bags or earthen pot fully foliage and well branched free from disease. shrubs (himalia, chandni ticomaor as direction by e/i etc.) 24 providing and displaying furcaria variegated hybrid well developed with fresh and healthy foliage 20cm and above atractive leaves in 35cm cement potas per direction of the officer in charge (dsr-18, 5.31pg. no. 147) 25 providing and stacking of alternanthera species of height 15cm to 20cm full of brnaches and foliages in 15cm size of earthen pot/plastic pot & as per direction of the officer in charge. (dsr-18, 6.20pg. no. 153) 26 providing and stacking of lpomea (golden leaves) with fresh and healthy leaves in 15cm size of earthen pot/plastic pot & as per direction of the officer in charge. 27 providing and stacking of syngonium (butterfly) variegated with 2-3 suckers healthy foliage in earthen pot/plastic pot as per direction of the officer in charge.(dsr-18, 6.15pg. no.153) 28 providing and stacking of wedelia trilobata, full of leaves in 15cm size of poly bags & as per direction of the officer in charge.(dsr-18, 6.26pg. no.153) 29 providing and stacking of pinus longifolia (pinus) of height 90-105cm in cement pot of size 35cm as per direction of the officer in charge (dsr-18, 7.65 pg. no.165) 30 earth work in excavation by mechanical means (hydraulic excavator) manual means in foundation trenches or drains ( not exceeding 1.5m in width or 10sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50mall kinds of soil 31 providing laying, jointing and testing of pvc(finolex make ring fit) of following dia 6kh/cm2 including all specials & fittings etc. as required for proper completion of work (the contractor has to arrange the source of water and require head for testing). (ar/yeida). 32 providing and fixing of hydrant with gate valve and all the fittings etc. complete. 32mm dia 33 complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, hergs, edge, flower beds, foliages, creepers etc. including hoeing, weeding, purning, replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter, removal of garden waste, applying insecticide, pesticide & fertilizers ( whenever required) top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by office in charge ( cost of good earth, manure , fertilizer, insecticide pesticide will be provided by the department & lawn mover and brush cutter with fuel and other t & p material / articles shall be provided by the contractor.) and as per direction of officer in charge. 34 play grounds/public parks ( mali for 2.00acre.) 35 boring of tubewell with: supplying assembling, lowering and fixing in vertical position in bore well, unplasticized pvc medium well casing (cm) pipe of required dia, conforming to is: 12818 , including required hire and labour charges, fittings & accessories etc. all complete for all depths, as per direction of engineer in charge. 36 providing profuse watering arrangement for lawn/park at site to make avialable for irrigation i.e. diesel engien & oil etc, rh pipe/ canvas pip & other t&p etc. in the proces of watering submerisible pump & accessories as per direction of officer in charge of work. 37 preparation of mounds of various size and shape by available excavated/supplied earth in layers not exceeding 20cm in depth breaking clods, watering of each layer dressing etc, lead upto 50mtr and lift upto 1.5m complete as per direction of officer in charge. 38 supply ofgood earth work , banking excavaated earth in layers not exceeding 20 cm in depth, breaking clods watering, rolling each layer with 1/2 tonnes roller or wooden or steel rammerand dressing up in embankments for roads, flood banks, marginal banks and guide banks or filling up ground depressions, all leads as per(a.r. )for all kind of soil. 39 plantation of seasonal two times on road side (0.45mtrwide bed) including making of bedas direction of engineer in charge complete item. 40 providing of seasonal seedlings including supply of seasonal seedling labour etc complete. 41 m/o seasonal/hedge of ground cover park including weeding hoeing and puring cutting in required shape etc. of ground bed complete itemand watering of seasoanl flowersincluding source of water pol etc. complete. 42 chair bench: supply of rcc chair bench with back rest of size 1500mm width x 1000mm height. reinforced suitably to promote long use and to prevent damage during handling, transportation, & erection. manufactured by using m-30 grade of concrete. 43 supply and fixing of dustbin set of 3capacity-80 ltr size -400x400 top , 300x 300 botto,, 900mm ht. stand made up of isi marked sq , pipe of 35mm x 35mm x 18 gauge power coated size-4.5’ x 1.5’ x 750mm(all complete) (as approved by e&i) 44 providing and laying in position cement concrete of specified grade excluding grade excluding the cost of centering and shuttering all work up to plinth level 1:2:4 corse sand 20 mm stone aggregate (sor based on dar 18 / 4.1.13)

State Government

TRN :49023607 | 16 May, 2025

Tender Value : 22.62 Lacs

Lucknow - Uttar Pradesh

Tender for tender for construction and renovation work of community center located in sector-d of kanpur road scheme - rcc repairs 2 chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of engineer-in-charge. 3 75mm average thickness 4 50mm average thickness 5 25 mm average thickness 6 cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of engineer-in-charge. 7 bars upto 12 mm diameter 8 bars above 12 mm diameter 9 drilling suitable holes in reinforced or plain cement concrete with power driven drill machine to a minimum depth of 100mm upto 200mm in rcc beams, lintels, columns and slabs to introduce steel bars for sunshades/balconies including fixing the steel bars in position using epoxy resin anchor grout of approved make but excluding the cost of reinforcement, all complete as per direction of engineer-in-charge.upto and including 12mm dia. 10 providing, mixing and applying bonding coat of approved adhesive on chipped portion of rcc as per specifications and direction of engineer-in-charge complete in all respect.epoxy bonding adhesive having coverage 2.20 sqm/kg of approved make 11 providing, mixing and applying sbr polymer (of approved make) modified cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of engineer-in-charge.note: measurement and payment: the pre-measurement of thickness shall be done just after the surface preparation is completed and payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 n/sqmm2). 12 25 mm average thickness in 2 layers. 13 50 mm average thickness in 3 layers. 14 providing and laying sbr polymer modified (of approved make @ minimum 2% by wt. of cement used) plain/reinforced concrete jacket for the structuralmembers e.g. columns, pillars, piers, beams etc with concrete having the specified minimum characteristic compressive strength [with ordinary portland cement, coarse sand and graded stone aggregate of 10mm maximum size in proportion as per design criteria] with specified average thickness all-round existing core of rcc member.note: rates shall be for finished surface area of concrete and shall include the cost of making holes in existing rcc slab, if required, for pouring concrete in shuttering mould of jacket and appropriate approved super-plasticiser forrendering concrete as flowable self compacting and sbr polymer but shall exclude cost of reinforcement, bond coat, shear keys, centering and shuttering, strutting, propping etc (payment under this item shall be madeonly after proper wet curing has been done and surface has been satisfactorily evaluated by sounding/tapping with a blunt metal instrument) 15 50mm thick in grade m 25 with cement content not less than 330 kg per cum 16 75mm thick in grade m 25 with cement content not less than 330 kg per cum 17 100mm thick in grade m 25 with cement content not less than 330 kg per cum 18 providing and injecting approved grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete/masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of engineer-in-charge.(the payment shall be made on the basis of actual weight of approved grout injected.) 19 epoxy injection grout in concrete/rcc work of approved make 20 providing, erecting, maintaining and removing temporary protective screens made out of specified fabric with all necessary fixing arrangement to ensure that it remains in position for the work duration as required by the engineerin- charge.wooven pvc cloth 21 shotcreting r.c.c. columns, beams and slabs etc. in layers with approved design mix concrete having the specified minimum characteristic compressive strength [with ordinary portland cement, coarse sand and graded stoneaggregate of 10 mm maximum size in proportion as per design criteria] including the cost of centering and shuttering at edges and corners etc. as directed by engineer- in-chargenote: rates shall include the providing necessary ground wires etc. the levelling gauges, if used, shall be paid for separately. payment under this item shall be made only after proper wet curing has been done and surface hasbeen satisfactorily evaluated by sounding/tapping with a blunt metal instrument. 22 50mm thick in grade m 25 with cement content not less than 330 kg per cum 23 75mm thick in grade m 25 with cement content not less than 330 kg per cum 24 providing and inserting 12mm dia galvanised steel injection nipple in honey comb area and along crack line including drilling of holes of required diametre (20mm to 30mm) up to depth from 30mm to 80mm at required spacing and making the hole & crack dust free by blowing compressed air, sealing the distance between injection nipple with adhesive chemical of approved make and allow it to cure complete as per direction of engineer-in-charge. 25 providing and fixing hard drawn steel wire fabric of size 75 x25 mm mesh or other suitable size wire mesh to be fixed & firmly anchored to the concrete surface by means of l shaped mild steel shear key welded with existing reinforcement including the cost of materials, labour, tool & plants as approved by engineer-in-charge. 26 mild steel or iron work in plain work such as in r.c.c. or r.b. (when not included in an over all rates ) including bending for proper completion of the workand including supply of steel and its wastage , bends, hooks and authorised overlaps shall be measured up to floor two level. 27 centering and shuttering including strutting, propping etc. and removal of form for : lintels, beams, plinth beams, girders, bressumers and cantilevers 28 centering and shuttering including strutting, propping etc. and removal of form for : columns, pillars, piers, abutments, posts and struts 29 centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thic 30 waterproofing and terracing 31 providing and laying in situ five course water proofing treatment with app (atactic polypropylene) modified polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd & 4th courses of bonding material @ 1.20 kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to is : 702, 3rd layer of roofing membrane app modified polymeric membrane 2.0 mm thick of 3.00 kg/ sqm weight consisting of five layers prefabricated with centre core as 100 micron hmhdpe film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron hmhdpe film. 5th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately). 32 cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate 33 miscellaneous works 34 providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, includingadditional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia m.s. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with m.s. tubes, m.s. tube challis, m.s. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. the scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of engineer-in-charge.note:- (1) the elevational area of the scaffolding shall be measured for payment purpose. (2) the payment will be made once only for execution of all items for such works. 35 disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of engineer-in-charge. 36 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in : cement mortar 1:6 (1 cement : 6 coarse sand) 37 cleaning of under ground sump, over head r.c.c. tank ( independent staging) including disposal of slit and rubbish, all as per direction of engineer-in-charge.the cleaning shall consist following operations:-(i) tank shall be emptied of water by pumping & bottom shall be cleaned of silt and other deposits.(ii) entire surface area of the sump shall then scrubbed thoroughly with wire brush etc. and pressure washed with water.(iii) chlorination of rcc internal surface by liquid chlorine.(iv) the treated surface shall be dried using air jetting and all loose particles shall be removal from the surface.(v) finally the surface shall be treated with ultraviolet radiation etc. as per direction of engineer-in-charge. 38 door-window repair 39 renewing glass panes, with putty and nails wherever necessary including racking out the old putty: float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/sqm) 40 renewal of old putty of glass panes (length) 41 demolishing r.c.c. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead asper direction of engineer - in- charge. 42 extra for cutting reinforcement bars manually/ by mechanical means in r.c.c. or r.b. work (payment shall be made on the cross sectional area of r.c.c. or r.b. work) as per direction of engineer-in-charge. 43 demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge. in cement mortar 44 dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :of area beyond 3 sq. metres 45 casement door double panel with french (false) mullion with zinc alloy (zamak) 3d hinges, multi-point locking system with cylinder, zinc alloy (zamak) powder coated handles on both sides.using r4 series with frame (64 mm & above) x (55 mm & above) & sash (64 mm & above ) x (100 mm& above) & french (false ) mullion (64mm & above) x (60 mm & above). (height above 2.5 metre) 46 toughened glass 12 mm thickness 47 finishing work 48 dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. 49 20 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) 50 removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 51 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface toprepare the surface even and smooth complete. 52 finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade: new work (two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 53 distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : new work (two or more coats) over and including water thinnable priming coat with cement primer 54 applying priming coat:with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works 55 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :one or more coats on old work 56 washrooms 57 dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.for thickness of tiles 10 mm to 25 mm 58 providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to is : 15622 of approved make in colours such as white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 59 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:30 mm thick including isi marked stainless steel butt hinges with necessary screws 60 providing and fixing aluminium handles, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm 61 providing and fixing aluminium tower bolts, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 200x10 mm 62 providing and fixing aluminium sliding door bolts isi marked anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Local Bodies

TRN :49026649 | 01 Jan, 0001

Tender Value : 0

Kangra - Himachal Pradesh

Tender for tender for supply of 1. sand crusher, per cubic foot. 2. gravel crusher 10, 20, 40 to 68 mm, per cubic foot. 3. sand pit, per cubic foot. 4. gravel pit, per cubic foot. 5. ball stone, per cubic foot. 6. broken stone, per cubic foot. 7. shuttering (edge, wall, danga / slab) per square feet. 8. cement transportation fare from thural to panchayat work site per bag. 9. jcb sand, per hour. 10. mixture, rate-per hour. 11. tiles, 12. sign board

State Government

TRN :49029493 | 15 May, 2025

Tender Value : 32.33 Lacs

Gautam Buddha Nagar - Uttar Pradesh

Tender for construction of e-library room in village begmabad yea. wc-06 - earth work in excavation in ordinary soil in all of foundation trenches including dressing of the side and ramming of bottom.lifts up to 1.50 m including getting out theexcavated soil and disposal of surplus excavated soil as directed with in a lead of 50m. (most/a.r./yeida) 2 supplying chemical emulsion in sealed containers including delivery as specified. chlorpyriphos/ lindane emulsifiable concentrate of 20%. (dar/2.34.1/based on uppwd/sor-2020)) 3 diluting and injecting chemical emulsion for post-constructional anti-termite treatment (excluding the cost of chemical emulsion) : treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 coarse sand) to match the existing floor: with chlorpyriphos/lindane e.c. 20% with 1% concentration (dar/2.35.3.1/based on uppwd/sor-2020)) 4 2.5 cm thick damp proof course with cement and approved coarse sand 1:1½ with and including water proofing as ordered by the engineer incharge in the proportion as specified by the manufacturer including supply of all materials, labour, tools & plants etc. required for proper completion of the work and including proper curing & shutterings as necessary. (uppwd/sor-2020/361) 5 applying a coat of residual petroleum bitumen of grade of vg-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. 6 cement concrete with 4cmgauge approved stone ballast, coarse sand & cement in the proportion of 8:4:1 including supply of all material, labour, tools&plants etc required for proper completion of the work. 7 b/w with bricks of class 150 in foundation & plinth in cm 1:4 (based on up pwd sor 2020) cement mortar 1:4 ( 1cement :4coarse sand) 8 m-150 brick work in 1:4 one cement and four course sand 2.20 f.m. mortar superstructure but for walls of half brick thick including supply of all material, labour, t&p etc. required for proper completion of the work. (uppwd/sor-2020/305(a)+310a 9 m-150 brick work in 1:4 one cement and four course sand 2.20 f.m. mortar superstructure but for walls of half brick thick including supply of all material, labour, t&p etc. required for proper completion of the work. (uppwd/sor-2020/305(a)+310a 10 extra for providing and placing in position 2 nos 6mm dia. m.s. bars at every third course of half brick masonry.uppwd-sor-2020-dar-18/6.15/ 11 providing and laying in position machine batched and machine mixed design mix m-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per is: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer-in-charge. (note :- cement content considered in this item is @ 330 kg/cum. excess/ less cement used as per design mix is payable/recoverable separately). all works upto plinth level 12 providing and laying in position machine batched and machine mixed design mix m-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per is: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer-in-charge. (note :- cement content considered in this item is @ 330 kg/cum. excess/ less cement used as per design mix is payable/recoverable separately).all works above plinth level upto floor v level 13 centringand shutteringincluding strutting, propping etc. andremoval of form for : foundation footings, base of column 14 centringand shutteringincluding strutting, propping etc. andremoval of form for : lintels, beams, plinth beam, grinder 15 centringand shutteringincluding strutting, propping etc. andremoval of form for : suspended floors, roofs, landings 16 columns, pillars, piers, abutments, posts and struts. (dar/5.9.6/based on uppwd/sor-2020)) 17 edges of slabs and breaks in floors and walls:under 20 cms wide. (dar/5.9.16.1/based on uppwd/sor-2020)) 18 earth work in rough excavation , banking excavaated earth in layers not exceeding 20 cm in depth, breaking clods watering, rolling each layer with 1/2 tonnes roller or wooden or steel rammer and rolling every 3rd and top most layer with power roller of minimum 8 tonnes and dressing up in embankments for roads, flood banks, marginal banks and guide banks or filling up ground depressions, all leads as per(a.r. )for all kind of soil. 19 steel rainforcement for r.c.c. work including straightening, cutting bending, placing in position and binding all complete upto plinth level thermo-mechanically treated bars of grade fe-500d or more./cold twisted bars. (dar/5.22.6/based on uppwd/sor-2020)) 20 12mm cement plaster of mix: 1:6 (1 cement : 6 coarse sand)based on up pwd sor 2020 dar-18/13.4.2 21 6mm cement plaster of mix: 1:3 (1 cement : 3 coarse sand)based on up pwd sor 2020 dar-18/13.17 22 15mm cement plaster of mix: 1:6 (1 cement : 6 coarse sand)based on up pwd sor 2020 dar-18/13.4.2 23 finishing walls with acrylic smooth exterior paint of required shade: new work (two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm). 24 distempering with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade 25 providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.dar-18/13.26 26 painting with synthetic enemel paint of approved brand and manufacture to give an even shade: two or more coats on new work. 27 providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, (i) single socketed pipes. 110mm dia 28 providing and fixing on wall face unplasticised - pvc moulded fittings/ accessories for unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion. single tee with door 110x110x110 mm (dar/12.42.3.2/based on uppwd/sor-2020) 29 bend 87.5° 110 mm bend (dar/12.42.5.2/based on uppwd/sor-2020) 30 shoe (plain) 110 mm shoe (dar/12.42.6.2/based on uppwd/sor-2020) 31 providing and fixing unplasticised -pvc pipe clips of approved design to unplasticised - pvc rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with m.s. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm (dar/12.43.2/based on uppwd/sor-2020) 32 providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.(dar/12.44/based on uppwd/sor-2020) 33 steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.dar-18/10.25.2 34 providing and fixing water closet squatting pan (indian type w.c. pan with 100mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required white vitreous china orissa pattern w.c. pan of size 580x440mm with integral type foot rests.up pwd sor-2020-dar 18/17.1.1 35 providing and fixing wash basin with c.l. brackets, 15 mm c.p. brass pillar taps,32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required:uppwd sor-2020-dar 17.7.1 36 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge.20mm od pipes. (dar/18.8.2/based on uppwd/sor-2020) 37 25mm od pipes. (dar/18.8.3/based on uppwd/sor-2020) 38 providing and fixingbrass gate valve with c.i. wheel of approved quality (screwed end) : 25 mm nominal bore. (dar/18.17.1/based on uppwd/sor-2020) 39 32 mm nominal bore. (dar/18.17.2/based on uppwd/sor-2020) 40 providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) applying a slurry coat of neat cement using 2.75 kg/sqm. of cement admixed with water proofing compound conforming to is. 2645 and approved by engineer-in-charge over the rcc slab including adjoining walls upto 300mm height including cleaning the surface before treatment. b) laying brick bats with mortar using broken bricks/brick bats 25 mm to 115mm size with 50% of cement mortar 1:5 (1 cement: 5 coarse sand) admixed with water proofing compound conforming to is : 2645 and approved by engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to is : 2645 and approved by engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c) after two days of proper curing applying a second coat of cement slurry using 2.75kg! sqm of cement admixed with water proofing compound conforming to is : 2645 and approved by engineer-in-charge. d) finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement: 4 coarse sand) admixed with water proofing compound conforming to is: 2645 and approved by engineer-in-charge including laying glass fibre doth of approved quality in top layer of plaster and finally finishing the surface with trowe’ with neat cement suvr an making pattern ot 300x300 mm square 3mm deep. e) the whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. all above operations to be done in order and as directed and specified by the engineer-in-charge: dar18/22.7.1 41 providing and placing on terrace (at all floor levels) polyethylene water storage tank isi: 12701 marked with cover and suttable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank dar 18/ 18.48 42 making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - iii) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.(dar 2018-4.17)based on uppwd sor/2020 43 providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. size of tile 600x600mm (dar/11.41.2/based on uppwd/sor-2020)) 44 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer-in-charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (dar/8.31/based on uppwd/sor-2020)) 45 providing and fixing brass bib cock of approved quality: 15 mm nominal bore (dar/18.15.1/based on uppwd/sor-2020)) 46 providing and fixingbrass gate valve with c.i. wheel of approved quality (screwed end) : 25 mm nominal bore. (dar/18.17.1/based on uppwd/sor-2020) 47 providing and fixing nahani trap 75x100mmincluding all complete. 48 20 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand-dar-18/13.6.1/p-902 49 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30mm thick including isi marked stainless steel butt hinges with necessary screws. (dar/9.21.2/based on uppwd/sor-2020)) 50 extra for providing isi marked stainless steel butt hinges instead of m.s. pressed butt hinges bright finished of required size with necessary screws. (shutter area to be measured). (dar/9.14/based on uppwd/sor-2020)) 51 renewing panes of glass in door, window & ventilators or fixing in the new work with 3mm thick glass panes fixed with brads & putty includung supply of all material , labour , tools & plants required for proper completion of workuppwd sor 2020/p26/806 52 prroviding and fixing isi mark 3 layer prelaminated particle board conforming to grade 2 type-iii of is-12823/20b laminated with 0.6-0.8 mm thick laminate conforming to is-2046/1995 and balancing lamination of 0.5 mm thick on the back side (size 700750430) including all complete 53 supply of work sb collection office/visitor chain with sheat dxwxh 400400450 mm padded with polyurithane foam complete 54 supply wook at site sb collection executive table of 3 layer prelaminated particle board (wood product) of grade 2 type 2 of is-12823/latest 1830 mm 950 mm 750mm including all complete 55 supplying and filling in plinth with jamuna sand under floors, including watering, ramming, consolidating and dressing complete. dar-18/2.27 56 providing and fixing factory made isi marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as f7d, f4b, k11 b and k12 b etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment).fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of c.c. 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 57 constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast r.c.c. horizontal grating with frame complete as per standard design with common burnt clay f.p.s. (non modular) bricks of class designation 7.5.(dar/18.33.1/based on uppwd/sor-2020) 58 providing, laying and jointing glazed stoneware pipes class sp-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : (dar/19.1.1/based on uppwd/sor-2020) 59 providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round s.w. pipes including bed concrete as per standard design : (dar/19.2.2/based on uppwd/sor-2020) 60 providing and fixing square-mouth s.w. gully trap class sp-1 complete withc.i. grating brick masonry chamber with water tight c.i. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: (dar/19.4.1/based on uppwd/sor-2020) 61 providing and fixing heavy class ss gratingof approved design including setting in floor with cement motor to match with floor finish as per architect requirement suitable for waster and ft, ut & fd.size 150 mm x 150 mm 62 providing and fixing ptmt towel rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.(dar/17.73.2/based on uppwd/sor-2020)) 63 providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with c.p. brass screws and washers complete. (dar/17.31/based on uppwd/sor-2020)) 64 providing and fixing ptmt soap dish holder having length of 138mm, breadth102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. (dar/18.65/based on uppwd/sor-2020)) 65 providing and fixing chicken wire mesh (murga jali) 24 gauge and 20 mesh at junction of rcc and masonry walls including fixing in position with steel nails of 25 mm in length as approved at required as directed by engineer-in-charge, scaffolding etc. complete. (ar/yeida//based on uppwd/sor-2020))½x24 gauge 66 providing and fixing aluminium hanging floor door stopper, isi marked, anodised (anodic coating not less than grade ac 10 as per is: 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.(dar/9.101.1/based on uppwd/sor-2020))single rubber stopper 67 providing and fixing aluminium tower bolts, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:250x10mm(dar/9.97.2/based on uppwd/sor-2020)) 68 providing and fixing aluminium handles,isi marked, anodised (anodic coating not less than grade ac 10 as per is: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete.125 mm (dar/9.100.1/based on uppwd/sor-2020)) 69 providing and fixing ptmt extension nipple for water tank pipe, fittings of approved quality and colour.25mm nominal bore, weighing not less than 62 gms. (dar/18.75.3/based on uppwd/sor-2020)) 70 providing & fixing of cp heavy duty bottle trap 32mm. (complete complying with relavent standard specification and as directed by the competent authority.) for wash basin&urinal 71 providing and fixing 1 mm thick m.s. sheet sliding-shutters, with frame and diagonal braces of 40x40x6 mm angle iron, 3 mm m.s. gusset plates at the junctions and corners, 25 mm dia pulley, 40x40x6 mm angle and t- iron guide at the top and bottom respectively, including applying a priming coat of approved steel primer up pwd sor-2020-dar-18/10.4 72 construction of granular sub-base by providing close graded material, mixing in mechanical mix plant at omc, carriage of mixed material to work at site, spreading uniform layers with motor grader on prepared surface and compacting with vibratory roller to achieve the desired density, complete as per clause 401 for grade-1 material. (morth/(ar/yeida/based on uppwd/sor-2020) 73 providing and laying 60mm thick i.s.i. mark factory made cement concrete interlocking concrete paver block made by block making machine with strong vibratory compaction of approved size, design, shape, laid in required colour and pattern over and including average 50mm thick compacted bed coarse sand and filling the joints with fine sand all complete as per the direction of engineer-in-charge with conforming to is-15658 and irc:sp:63. (ar/yeida/ based on uppwd/sor-2020) 74 wiring point for light in 1.5 sq. mm. pvcinsulated singlecorecopperconductor cable (inpvcconduit with 1.5sq.mm. frlsh pvc insulated multistrand copperconductor cable as earth wire drawn inside conduit.)and5 amp.flush typeswitch& ceiling rose/angle/batten holderfixedwith3mmthickphenolic laminate backalitesheet withbrass machinescrews andcup washers mounted overexisting m.s.switch boardbox/junction boxwith supplyofallmaterial, labour& t&p etc. requiredforproper completion of the work complete in all respect, as directed by engineer in charge pwd-2018 ps no-174c 75 supply and wiring of submains with 2 nos. of 2.5 sq. mm. frlsh pvc insulated1100 vgrade multistrand singlecore copper conductorcable in 25mm dia heavy duty (2mm thick) pvc conduitwith2 nos 2.5 sq.mm.frlsh pvc insulated multistrand copperconductor cable asearth continuity wire drawn in conduit complete in all respect, as directed by engineer in charge pwd-2018 ps no-261c 76 supply and fixing of power plug with 20 amp./250 voltflush type modularswitchand 5 pin 20 a/250 voltflush typeuniversal modular socket switch on concealed m.sboxincluding supply of allmaterial, labourt&petc. complete in all respect, as directed by engineer in charge .pwd-2018 ps no-1139a 77 s&f surface/flush mounting 8 ways spn distribution board with additional metal door without mcb complete in all respect, as directed by engineer in charge. pwd-2018 ps -1024a 78 s&f of 6 amp to 32 amp. mcb (10 ka) c curve complete in all respect, as directed by engineer in charge.pwd-2018ps -1002cat-a 79 s&f of 40amp. dp mcb (10 ka) c curve complete in all respect, as directed by engineer in charge. pwd-2018 ps no-1010 cat-a 80 providing and fixing circular/ hexagonal cast iron or m.s. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick m.s. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ m.s. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. clamp shall be made of 12 mm dia m.s. bar bent to shape as per standard drawing. (dar/10.18/based on uppwd/sor-2020))

Central Government/Public Sector

TRN :34404893 | 12 May, 2025

Tender Value : 0

Jamshedpur - Jharkhand

Tender for gem bids for clearing jungle including uprooting of rank vegetation grass brush wood trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. "supplying chemical emulsion in sealed containers including delivery as specified. chlorpyriphos or lindane emulsifiable concentrate of 20 percent" "diluting and injecting chemical emulsion for post constructional anti termite treatment excluding the cost of chemical emulsion along external wall where the apron is not provided using chemical emulsion at the rate 7.5 litres or sqm of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall and rodding etc. complete isto with chlorpyriphos or lindane e.c. 20 percent with 1 percent concentration" "earth work in excavation by mechanical means hydraulic excavator or manual means in foundation trenches or drains not exceeding 1.5 m in width or 10 sqm on plan including dressing of sides and ramming of bottoms lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m all kinds of soil." filling available excavated earth excluding rock in trenches plinth sides of foundations etc. in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering lead up to 50 m and lift upto 1.5 m supplying and filling in plinth with sand under floors including watering ramming consolidating and dressing complete. "providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level 1 isto 3 isto 6 1 cement 3 coarse sand zone iii 6 graded stone aggregate 20 mm nominal size " "providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering shuttering finishing and reinforcement all work up to plinth level isto 1 isto 1.5 isto 3 1 cement 1.5 coarse sand zone iii 3 graded stone aggregate 20 mm nominal size " "reinforced cement concrete work in walls any thickness including attached pilasters buttresses plinth roof and string courses fillets columns pillars piers abutments posts and struts etc. above plinth level up to floor five level excluding cost of centering shuttering finishing and reinforcement 1 isto 1.5 isto 3 1 cement 1.5 coarse sand zone iii 3 graded stone aggregate 20 mm nominal size " brick work with common burnt clay f.p.s. non modular bricks of class designation 7.5 in foundation and plinth in cement mortar 1 isto 6 1 cement 6 coarse sand brick work with common burnt clay f.p.s. non modular bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in cement mortar 1 isto 6 1 cement 6 coarse sand "half brick masonry with common burnt clay f .p .s. non modular bricks of class designation 7.5 in superstructure above plinth level up to floor v level. cement mortar 1 isto 4 1 cement 4 coarse sand " "centering and shuttering including strutting propping etc. and removal of form for foundations footings bases of columns etc. for mass concrete" "centering and shuttering including strutting propping etc. and removal of form for suspended floors roofs landings lintals beams balconies and access platform" "steel reinforcement for r.c.c. work including straightening cutting bending placing in position and binding all complete upto plinth level thermo mechanically treated bars of grade fe 500d or more make sail or tata or jindal " "15 mm cement plaster on the rough side of single or half brick wall of mix isto 1 isto 6 1 cement isto 6 fine sand rates for external plastic are for height upto 10m from ground level in less otherwise stated cement make nuvoco lafarge or ultratech or acc or as per direction of eic " "12 mm cement plaster of mix 1 isto 6 1 cement isto 6 fine sand rates for external plastic are for height upto 10m from ground level in less otherwise stated cement make nuvoco lafarge or ultratech or acc or as per direction of eic " "6 mm cement plaster of mix 1 isto 3 1 cement 3 fine sand rates for external plastic are for height upto 10m from ground level in less otherwise stated cement make nuvoco lafarge or ultratech or acc or as per direction of eic " neat cement punning. "finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade new work two or more coats applied at the rate 1.43 ltr or 10 sqm over and including priming coat of exterior primer applied at the rate 2.20 kg or 10 sqm make dulux or burger or asian paints or as per direction of eic" white washing with lime to give an even shade new work three or more coats mix with fevicol ddl and robin blue or as per direction of eic "painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. preferable make dulux or burger or asian paints or as per direction of eic make dulux or burger or asian paints or as per direction of eic" making plinth protection 50mm thick of cement concrete 1 isto 3 isto 6 1 cement 3 coarse sand zone iii 6 graded stone aggregate 20 mm nominal size over 75mm thick bed of dry brick ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including necessary excavation levelling and dressing and finishing the top smooth "providing and fixing angle iron frames for doors windows and ventilators of mild steel angle sections of size 35x35x5 mm joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing t iron frame or to the wall with dash fastener including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer all complete as per the direction of engineer in charge. make sail or tata or jindal " "providing and fixing isi marked flush door shutters conforming to is isto 2202 part i decorative type core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including isi marked stainless steel butt hinges with necessary screws" "structural steel work in single section fixed with or without connecting plate including cutting hoisting fixing in position and applying a priming coat of approved steel primer all complete. make sail or tata or jindal " 25 mm thick pvc flush door shutters made out of a one piece multi chamber extruded pvc section of the size of 762 mm into 25 mm or less as per requirement with an average wall thickness of 1 mm plus or minus 0.3 mm . pvc foam end cap of size 23x10 mm are provided on both vertical edges to ensure the overall thickness of 25 mm. m.s. tube having dimensions 19 mm into 19 mm and 1.0 mm plus or minus 0.1 mm is inserted along the hinge side of the door. core of the door shutter should be filled with high density polyurethane foam. the top and bottom edges of the shutter are covered with an end cap of the size 25 mm into 11 mm. door shutter shall be reinforced with special polymeric reinforcements as per manufacturer specification and direction of engineer in charge to take up necessary hardware and fixtures. stickers indicating the locations of hardware will be pasted at appropriate places "providing and fixing isi marked oxidised m.s. sliding door bolts with nuts and scrows etc. complete .as per the direction of directions of engineer in charge.300x16 mm " "providing and fixing ist quality ceramic glazed wall tiles conforming to is 15622 thickness to be specified by the manufacturer of approved make somany or kajaria or nitco in all colours shades except burgundy bottle green black of any size as approved by engineer in charge in skirting risers of steps and dados over 12 mm thick bed of cement mortar 1 isto 3 1 cement 3 coarse sand and jointing with grey cement slurry at the rate 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. make isto somany or kajaria or nitco or asian or as per direction of eic" "providing and laying vitrified floor tiles in different sizes thickness to be specified by the manufacturer with water absorption less than 0.08percent and conforming to is 15622 of approved make in all colours and shades laid on 20mm thick cement mortar 1 isto 4 1 cement 4 coarse sand jointing with grey cement slurry at the rate 3.3 kg or sqm including grouting the joints with white cement and matching pigments etc. complete. size of tile 600x600 mm make somany or kajaria or nitco or asian or as per direction of eic" "providing and fixing water closet squatting pan indian type w.c.pan with 100 mm sand cast iron p or s trap 10 litre low level white p.v.c. flushing cistern including flush pipe with manually controlled device handle lever conforming to is 7231 with all fittings and fixtures complete including cutting and making good the walls and floors wherever required white vitreous china orissa pattern w.c. pan of size 580x440 mm with integral type foot rests preferable make hindware or parrywair or hindustan or cera or direction of eic" "providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and c.p. brass spreaders with brass unions and g.i clamps complete including painting of fittings and brackets cutting and making good the walls and floors wherever required one urinal basin with 5 litre white p.v.c. automatic flushing cistern preferable make hindware or parrywair or hindustan or cera or direction of eic" "providing and fixing wash basin with c.i. brackets 15 mm c.p. brass pillar taps 32 mm c.p. brass waste of standard pattern including painting of fittings and brackets cutting and making good the walls wherever require isto white vitreous china wash basin size 630x450 mm with a single 15 mm c.p. brass pillar tap" "providing and fixing p.v.c. waste pipe for sink or wash basin including p.v.c. waste fittings complete. semi rigid pipe 32 mm dia" providing and fixing 600x450 mm beveled edge mirror of superior glass of approved quality complete with 6 mm thick hard board ground fixed to wooden cleats with c.p . brass screws and washers complete. "providing and fixing brass bib cock of approved quality 15 mm nominal bore" "providing and fixing brass stop cock of approved quality 15 mm nominal bore" providing and fixing circular or hexagonal cast iron or m.s. sheet box for ceiling fan clamp of internal dia 140 mm 73 mm height top lid of 1.5 mm thick m.s. sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron or m.s. sheet box by means of 3.3 mm dia round headed screws one lock at the corners. clamp shall be made of 12 mm dia m.s. bar bent to shape as per standard drawing. providing and fixing isi marked oxidised m. s handles conforming to is 4992 with necessary screws etc. complete 125 mm providing and fixing bright finished brass hanging type floor door stopper with necessary screws etc. complete. providing and fixing is 12817 marked stainless steel butt hinges heavy weight with stainless steel screws etc. complete 100x60x2.50 mm "providing and fixing g.i. pipes complete with g.i. fittings including trenching and refilling etc. for external work a. 15 mm dia nominal bore preferable make tata or jindal or as per direction of eic" "providing and fixing g.i. pipes complete with g.i. fittings including trenching and refilling etc. for external work b. 20 mm dia nominal bore preferable make tata or jindal or as per direction of eic" providing and fixing g.i. pipes complete with g.i. fittings including trenching and refilling etc. for external work d. 50 mm dia nominal bore preferable make tata or jindal or as per direction of eic "providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is 13592 type a including jointing with seal ring conforming to is 5382 leaving 10 mm gap for thermal expansion single socketed pipes. 110 mm diameter" "providing and fixing gun metal gate valve with c.i. wheel of approved quality screwed end isto 20 mm nominal bore" "providing and fixing gun metal gate valve with c.i. wheel of approved quality screwed end isto 50 mm nominal bore" providing and placing on terrace at all floor levels polyethylene water storage tank is isto 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet outlet and overflow pipes but without fittings and the base support for tank. providing and fixing 100 mm sand cast iron grating for gully trap constructing brick masonry chamber for underground c.i. inspection chamber and bends with bricks in cement mortar 1 isto 4 1 cement 4 coarse sand c.i. cover with frame light duty 455x610 mm internal dimensions total weight of cover with frame to be not less than 38 kg weight of cover 23 kg and weight of frame 15 kg r.c.c. top slab with 1 isto 1.5 isto 3 mix 1 cement 1.5 fine sand isto 3 graded stone aggregate 20 mm nominal size foundation concrete 1 isto 5 isto 10 1 cement 5 fine sand 10 graded stone aggregate 40 mm nominal size inside plastering 12 mm thick with cement mortar 1 isto 3 1 cement isto 3 coarse sand finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets isto with common burnt clay f.p.s. non modular bricks of class designation 7.5 "constructing masonry chamber 30x30x50 cm inside in brick work in cement mortar 1 isto 4 1 cement isto 4 coarse sand for stop cock with c. i. surface box 100x100 x75 mm inside with hinged cover fixed in cement concrete slab 1 isto 2 isto 4 mix 1 cement isto 2 coarse sand isto 4 graded stone aggregate 20 mm nominal size i or c necessary excavation foundation concrete 1 isto 5 isto 10 1 cement isto 5 fine sand isto 10 graded stone aggregate 40mm nominal size and inside plastering with cement mortar 1 isto 3 1 cement isto 3 coarse sand 12mm thick finished with a floating coat of neat cement complete as per standard design isto with common burnt clay f.p.s. non modular bricks of class designation 7.5" providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level isto 1 isto 1.5 isto 3 1 cement isto 1 coarse sand zone iii 3 graded stone aggregate 20 mm nominal size making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and s.w. drain pipe 100 mm diameter 1.8 m long complete as per standard design. with common burnt clay f.p.s. non modular bricks of class designation 7.5 "cement concrete flooring 1 isto 2 isto 4 1 cement isto 2 coarse sand isto 4 graded stone aggregate finished with a floating coat of neat cement including cement slurry but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate" "providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm plus 0.05 percent total coated thickness zinc coating 120 grams per sqm as per is 277 in 240 mpa steel grade 5 to 7 microns epoxy primer on both side of the sheet and polyester top coat 15 to 18 microns using self drilling or self tapping screws complete ridges plain 500 to 600mm " "providing and fixing precoated galvanised iron profile sheets size shape and pitch of corrugation as approved by engineer in charge 0.50 mm plus 0.05 percent total coated thickness with zinc coating 120 grams per sqm as per is 277 in 240 mpa steel grade 5 to 7 microns epoxy primer on both side of the sheet and polyester top coat 15 to 18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by engineerin charge. the sheet shall be fixed using self drilling or self tapping screws of size 5.5 x 55 mm with epdm seal complete upto any pitch in horizontal or vertical or curved surfaces excluding the cost of purlins rafters and trusses and including cutting to size and shape wherever required." providing and fixing of glass panes with putty and glazing clips in steel doors and windows all complete with 4mm thick glass panes etc. complete. supply of led tube light fittings .make c.g. or philips fixing of led tube light fittings including supply of all hardwares as required. led fitting will be supplied by contractor. make c.g. or philips supply of 48 sweep ceiling fan complete with down rod.clamp canopy etc. fixing of 48 sweep ceiling fan complete with down rod.clamp canopy etc.fan hardwares required for fixing for i.e. nut bolts clamp screws etc wiil be supplied by contractor. supply and fixing of stepped type electronic fan regulator on existing switch board. wiring for light point fan point exhaust fan point with 1.5 sqmm frls pvc insulated copper conductor single core cable in consield with modular switch modular plate suitable gi box and earthing the point with 1.5 sqmm frls pvc insulated copper conductor cable as required. supply of frls pvc insulated copper conducter single core cable of size 6 sqmm. make havells or kei or polycab or national wiring for circuit or submain wiring along with earth wire with the following sizes of frls pvc insulated copper conductor single core cable in consield or recessed medium class pvc conduit in concield as required 2 x 6 sqmm plus 1 x 6 sqmm earth wire. all the three colours should be red blue and green supply and fixing of utility db p or s 20a dp metal plug and socket distribution board grey make anchor or havells supply and installation of three phase industrial box with 32 amp 4 pole mcb and 5 pin top plug. make neptune or reputed make supply of frls pvc insulated copper conducter single core cable of size 10 sqmm. make havells or kei or polycab or national wiring for circuit or submain wiring along with earth wire with the following sizes of frls pvc insulated copper conductor single core cable in surface or recessed medium class pvc conduit in concield as required 4 x 10 sqmm + 1 x 10 sqmm earth wire.all the five colours should be red blue yellow black and green preparation of earth pit with supply of all materials including 3m long 3.64mm thick perforted gi tube with salt and charcol in alternate layer and brick chamber at the top with chequered plate 6mm thick as per is 3043 with latest. supply and laying 25mm x 5 mm gi strip at 0.5 meter below ground or wall including connection with electrode with db. supply of all hardware are in scope of contractor supply ans fixing of surface mounting vertical type 415 volts tpn mcb distribution board of sheet steel dust proctected duly power coated painted inclusive 200 amp tinned copper bus bar common neutral link earth bar din bar for mounting mcb with provision of 100 amp tpn mccb as incomer interconnection between incomer mccb and busbar. supply and fixing of 5 to 32 amp rating 240 or 415 volt mcb suitable as per load. supply and fixing of four pole 100 amp rating 415 volt 16 ka mccb . laying of 1.1kv grade pvc al.cable of size 2 or 3 or 3.5 or 4c 2.5 or 6 or 10 or 16 or 25 or 35 sq.mm in underground trench of 760mm deepx760mm wide in single tier formation including trench excavation and back filling with bricks 15brick or m and sand protection route marker. road or concreete or bolder cutting and finishing the road to its original shape are in the scope of the contractor. supply and fixing of street light on wall including supply of all necessaryu hardware for fixing of fitting on wall. supply and fixing of bulk head fitting on wall including supply of all necessaryu hardware for fixing of fitting on wall. supply installation and commissioning of exhaust fan of size 300 mm dia. this includes cutting of wall and finishing and supply of hardware like nut bolts etc. make crompton

Related Searched Keywords : edge wall

List of edge-wall Tenders

Get edge wall Tender Alert...

Related Searched Keywords : edge wall

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us