Filters

List of cement-sheet Tenders

List of latest cement-sheet Tenders in Indian Tenders. Click on any cement-sheet Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for cement-sheet Tenders.

All-Tenders (44)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

State Government

TRN :35558958 | 16 Oct, 2025

Tender Value : 9.80 Lacs

Jaipur - Rajasthan

Tender for earth work in excavation by mechanical means (hydraulic excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sum on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. all kinds of soils "pcc in foundation : providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - all work up to plinth level. 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)." providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - all work up to plinth level. m10 grade nominal mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).floor random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in: cement mortar 1:6 ( 1-cement : 6-sand). centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for foundation, footings, strap beam, raft, base of column etc centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for : suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks, sills, chhajjas, lintel, beam, plinth beam etc. centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for columns, pillers, posts,and struts etc "providing and laying in position specified grade of cement concrete for all rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. m20 grade nominal mix / design mix add extra for providing richer mixes respectively at all floor levels providing m-25 grade concrete by using cement as per codal provision instead of m-20 grade design mix." "providing and laying in position specified grade of cement concrete for all rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. m20 grade nominal mix / design mix" providing and laying in position specified grade of cement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcement for walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.m20 grade nominal mix / design mix add extra for providing richer mixes respectively at all floor levelsproviding m-25 grade concrete by using cement as per codal provision instead of m-20 grade design mix. supply & stacking good soil of earth at site complete including loading unloading & transportation etc.good soil of earthfilling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift. stone kharanja : random rubble dry stone kharanja under floor. brick work with clay flyash f.p.s. brick (is 13757- 1993 ) of class designation 75 in superstructure above plinth level upto floor five level in : cement mortar 1 : 6 (1 cement : 6 coarse sand) providing and laying in position specified grade of cement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement for beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix / design mix providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. thermo-mechanically treated bars (conforming of relevent is code) providing and fixing m.s. sheet 1mm thick single leaf door shutter in angle iron frame 35x35x5mm suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of engg. incharge but excluding cost of chowkhats: including two coats of anit-corrosive red oxide primer paint extra for double leaf shutters. providing and fixing steel glazed doors windows and ventilator shutters of standard rolled steel section (is 1038-1983) joints mitred and welded with steel lugs 13x3mm, 10cm. long embedded in cement concrete block 15x10x10cm. of 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of plain glass panes 4mm thick with cooper glazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approval steel primer, excluding the cost of metal beading and other fitting except necessary hinges of pivots steel handles peg stay etc. as required :partly fixed and partly openable [ fixed area not to exceed 33%] supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance. guard bars : providing and fixing square bars or other flat welded to window, ventilatiors etc. kota stone slab flooring 25 mm thick over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) for area of each slab from 2001 to 5000 sq.cm : kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete for area of each slab upto 2001 sqcm internal plaster : plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :12mm thick. external plaster : plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :20mm thick. plaster (ceiling): 6 mm thick cement plaster to ceiling of mix 1:3 (1cement : 3-fine sand) grading roof for water proofing treatment with water proffing compound cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : copping : providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc up to floor five level excluding the cost of centering and shuttering. m15 grade nominal mix 1: 2: 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete internal finishing: distempering with oil bound washeble distemper of approved brand and manufacture to give an even shade including all scaffolding new work (two or more coats) over and including scrapping and priming coat with cement primer finishing walls with acrylic smooth exterior paint of required shade including all scaffolding. new work (two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm ). panting on doors & windows :- painting with synthetic enamel paint of approved brand and manufacture to give an even shade : two or more coats on new work providing and fixing in cm 1 : 4 double paitam (rebated) stone door window and ventilator frames of approved quarry:size 125 x 100mm p&f rigid pvc pipe (is:4985 mark) class ii(4 kg. /cm.) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant 110mm dia p&f rigid pvc pipe fittings (is: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: bend 87.5 110mm dia pipe clip 110mm dia wiring of light point/ fan point/ exhaust fan point/ call bell point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (is:694) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) in recessed isi marked mms ( is:9537 p - iii ) vergin material pvc conduit & it's all accessories( j.b. , bends etc.) , round tiles,18 swg hot dipped galvanized modular box with earth terminal, 6 a modular switch, modular face plate with grid plate, 3 pin ceiling rose / lamp holder/ 3 pin connector , screws etc, making connections,all as per pre approved by engineer in charge, testing etc. complete as required. for specification of copper conductor, phenolic laminated sheet's & electrical/ wiring accessories refer chapter e - 04, e - 05 & e - 07 . for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . short point (up to 3 mtr.) medium point (up to 6 mtr) long point (up to 10 mtr) wiring of 3/5 pin 6 amp. light plug point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (is:694) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) in recessed isi marked mms ( is:9537 p - iii ) vergin material pvc conduit & it's all accessories( j.b. , bends etc.) , round tiles,18 swg g.i. box with earth terminal of required size, 6 a switch, 3/5 pin 6 a socket, 3.0 mm thick isi marked phenolic laminated sheet (is : 2036 - 1995), al. alloy/ cadmium plated iron screws 20 mm cup washers etc. all as per pre approved by engineer in charge, making connections, testing etc. complete as required. for specification of copper conductor, phenolic laminated sheet's & electrical/ wiring accessories refer chapter e - 04, e - 05 & e - 07. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . on board s&f following sizes (dia.) of isi marked mms ( is:9537 p - iii ) vergin material pvc conduit as per pwd specification for electrical works along with its accessories (is: 3419 ) as required in recess including cutting the wall, covering conduit and making good the same as required. all relative and latest acceptance tests reports by any nabl accredited lab for the conduit shall be submitted before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . mms (9537 p-111)pvc condute.25mm. supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked (is:694) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a ,flame retardant as per is 10810-53, better amperage rating as per vde 0298 part 4, , in existing surface or recessed pvc/ ms conduit/casing capping including all as per pre approved by engineer in charge,making connections, etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . 2 x1.5 sqmm supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked (is:694) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a ,flame retardant as per is 10810-53, better amperage rating as per vde 0298 part 4, , in existing surface or recessed pvc/ ms conduit/casing capping including all as per pre approved by engineer in charge,making connections, etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . 2 x2.5 sqmm providing & fixing of 240/415 v ac mcb with positive isolation of breaking capacity not less than 10 ka (b/ c tripping characteristic as per type of load and site requirement) 4kv impulse withstand voltage, as per pwd specification for electrical works with isi marked is 8828(1996) / conforming to iec 60898-1 2002, iec 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , ip 20 contact protection and fitted with existing distribution board/sheets, min. operation 20,000 upto 32 a rating and 10,000 upto 63 a, 5000 for 80 a rating including making connections, testing etc. as required. . oem shall have submit nabl / cpri / erda accrediated lab test reports before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr .6a to 32a rating. 50 a to 63a rating providing & fixing of ip20 smd mid power led batten type integrated light fixture made from polycarbonate /extruded aluminium powder coated housing with in built driver , power consumption of 18w/20w ,system lumen efficacy = 120 lm/watt output, internal surge protection of 2.5 kv with short & open circuit protection ,thd < 10% ,p.f.=0.95, cri >80 , life time of minimum 50000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing. 1170mm(+/-10%) led batten with min. lumen output 2200 lm providing & fixing of energy efficient /energy saving ip 20 led direct retrofit bulb in existing holder or fixture as required with system lumen efficacy =100 lm/watt output ,pf 0.95 , cri >70, minimum life time of minimum 25000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . for additional technical parameters of product/ work, refer annexure "a" attacheded with this bsr.6/7 watt providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed un-arrmoured aluminium cable confirming to is:1554 p-i / is :7098 p - i of 1.1 kv with h4- grade electrolytic aluminium conductor confirming to is 8130 of purity >99.6 %, inner / outer sheath confirming to is:5831 in existing rcc / hume / stoneware / pvc pipe/ open duct/cable trench / cable tray (with cable tie) including testing etc. as required of following size. oem must have it's own in house nabl accrediated laboratory for testing procedure as per is:10810. for additional technical parameters of product / work refer annexure 'a' attached with this bsr 6.0 sq. mm 4 core providing & fixing of bee star rated copper wounded double ball bearing capacitor start, aluminium body & metallic blade ceiling fan conforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing (i.e. isi marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . providing & fixing of isi marked (is:1258) batten/angle lamp holder with cm/l no. printed and made out from industrial grade polycarbonate or fire resistant abs material, brass terminal & captive screwsincluding making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . p & f 1.2mm thick m.s. recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side . all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure 'a' attached with this bsr providing & fixing of 240/415 v isolator as per pwd specification for electrical works with isi marked is:13947-iii/conforming to iec 60947-3, suitable for ac22a utilization catagory, 4kv impulse withstand voltage, true contact indication, red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting, minimum phase termination capacity of 35sq.mm. , label holding facility , ip 20 contact protection and fitted with existing distribution board / sheet including making connections, testing etc. as required. oem shall have submit nabl / cpri / erda accrediated lab test reports before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . 30/40 amp rating . providing & fixing of modular type 120 w step fan regulator duly isi marked (is 11037:1984 ) with cm/l no. printed made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with ip-20 rating , including all as per pre approved by engineer in charge,making connections, testing etc. as required. for additional technical parameters of product / work refer annexure 'a' attached with this bsr5 step fan regulator 2 module 360 dgree rotating p & f isi marked (is:3854) 6 amp. flush type non modular switch with cm/l no. printed and made out from industrial grade polycarbonate or fire resistant abs material including cutting hole in tile and making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . providing & fixing of of 3/5 pin 6 amp. flush type non modular socket made out from industrial grade polycarbonate or fire resistant abs material, brass terminal with porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr .

State Government

TRN :35559003 | 16 Oct, 2025

Tender Value : 25.85 Lacs

Jaipur - Rajasthan