Filters

List of zone-work Tenders

List of latest zone-work Tenders in Indian Tenders. Click on any zone-work Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for zone-work Tenders.

All-Tenders (256)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

Cooperative

TRN :49019449 | 20 May, 2025

Tender Value : 1.00 Lacs

Palacode - Tamil Nadu

Tender for tender for 12mw co-gen boiler external cleaning and painting work in labour contract basis; scope of the work1. providing of scaffolding work in the boiler up to the super heater coils with proper scaffolding materials and to ensure the work man safety.2. all accumulated ashes to be cleared in all the zone of the boiler.3. all the water wall tubes, bank tubes, super heater coil, economizer tube, air pre heater tubes are to be cleaned with using wire brushes and emery sheets.4. esp zone and flue gas duct up to chimney to be cleaned with using wire brushes and emery sheets.5. if the cleaning is not proper / not satisfied it should be rework till the satisfaction of plant officials.6. after proper cleaning of the tubes and ducts all are to be painted with the boiler exterior paint.7. all the collected ashes to be disposed to the ash yard each and every day.8. rate should be quoted in lumsum basis.

Local Bodies

TRN :49019484 | 13 May, 2025

Tender Value : 3.62 Lacs

Edavaka - Kerala

Tender for tender for supply of material for koleyeri bajanamdam thod side protection ward 11 thod side protection , culvert , stone aggregate 40 mm nominal size , stone aggregate 20 mm nominal size , coarse sand (zone 3) , portland cement , mixer machine , vibrater , culvert , sundries , stone aggregate 10 mm nominalsize , twisted steel bar , stone for masonary work

Government Departments

TRN :49019524 | 15 May, 2025

Tender Value : 1.05 Lacs

Piravom - Kerala

Tender for tender for supply of mauegs material work ward 14 ward1manadathupady-tharappady road= 1 stone aggregate 2 40 mm nominal size 3 20 mm nominal size 4 10 mm nominal size 5 portland cement 6 coarse sand (zone 3) 7 concrete mix machine 8 display board

State Government

TRN :49019580 | 14 May, 2025

Tender Value : 7.89 Lacs

Mohali - Punjab

Tender for tender for misc civil works in the campus; 1 supplying and filling in plinth withsand under floors, including watering, ramming, consolidating and dressing complete. 2 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level : 3 1:4:8 (1 cement : 4 coarse sand (zone-iii) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) 4 providing and laying in position specified grade of reinforced cementconcrete, excluding the cost of centering, shuttering, finishing andreinforcement - all work up to plinth level : 5 1:2:4 (1 cement : 2 coarse sand (zone-iii) derived from naturalsources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) 6 centering and shuttering including strutting, propping etc. and removalof form for 7 foundations, footings, bases of columns, etc. for mass concrete 8 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 9 thermo-mechanically treated bars of grade fe-500d or more. 10 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in foundation and plinth in: 11 cement mortar 1:6 (1 cement : 6 coarse sand) 12 providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand),jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 13 600x600 mm 14 12 mm cement plaster of mix : 15 1:6 (1 cement: 6 fine sand) 16 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 17 distempering with 1st quality acrylic distemper (ready mixed) having voc (volatile organic compound ) content less than 50 gram/ litre, of approved brand and manufacturer including applying additional coats wherever required to achieve even shade and colour 18 old work (one or more coats) 19 removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 20 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 21 one or more coats on old work 22 supplying and stacking at site. 23 good earth 24 taking out existing cc interlocking paver blocks from footpath/ centralverge, including removal of rubbish etc., disposal of unserviceablematerial to the dumping ground, for which payment shall be madeseparately and stacking of serviceable material within 50 metre leadas per direction of engineer-in-charge. 25 laying old cement cocrete interlocking paver blocks of any design/shape laid in required line, level, curvature, colour and pattern overand including 50 mm thick compacted bed of coarse sand, filling thejoints with fine sand etc. all complete as per the direction of engineer in-charge. (old cc paver blocks shall be supplied by the departmentfree of cost).

State Government

TRN :49019760 | 13 May, 2025

Tender Value : 0

Kanpur - Uttar Pradesh

Tender for tender for pd campus colony - dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. dsr -15.56 2 12 mm cement plaster of mixwith 1:6 (1 cement: 6 coarse sand) dsr 13.4.2 on wall. 3 12 mm cement plaster of mixwith 1:4 (1 cement: 4 coarse sand) dsr 13.4.1 on celling. 4 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) nondecorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 35 mm thick including isi marked stainless steel butt hinges with necessary screws.dsr-9.21.1 5 providing and fixing fly proof galvanized m.s. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. with second class teak wood beading 62x19 mm.dsr-9.51.1 6 removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. completedsr - 13.88 7 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.dsr-13.80 8 finishing walls with water proofing cement paint of required shade .( old work one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm complete including cost of priming coat. ) dsr-13.109.1 9 distempering with 1st quality acrylic distemper (ready mixed) having voc (volatile organic compound ) content less than 50 gram/ litre, of approved brand and manufacturer including applying additional coats wherever required to achieve even shade and colour .dsr-13.81 10 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : one or more coats on old workdsr-13.99.1 11 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. concealed work, including cutting chases and making good the walls etc.15 mm nominal dia pipes . dsr 18.8.1 12 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply and all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. 25 mm nominal dia pipes . dsr 18.8.3 13 providing and fixing c.p. brass bib cock of pproved quality conforming to is:8931 : 15 mm nominal bore sor/dsr 18.49.1 14 providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require. white vitreous china wash basin size 630x450 mm with asingle 15 mm c.p. brass pillar tap dsr 17.7.2 15 providing and fixing water closet squatting pan (indian type w.c. pan ) with 100 mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. white vitreous china orissa pattern w.c. pan of size 580x440 mm with integral type foot rests dsr 17.1.2 16 brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to is: 2222 in superstructure above plinth level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) . with f.p.s.(non modular) bricks .dsr-6.4.2 17 cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate dsr 11.3.1 18 providing and fixing p.v.c. low level flushing cistern with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete.10 litre capacity - white .dsr-17.18.1 19 providing and placing on terrace (at all floor levels) polyethylene water storage tank, is : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. dsr-18.48 20 1:4:8 (1 cement : 4 coarse sand (zone-iii) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources). dsr 4.1.8 21 providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, (i) single socketed pipes.110 mm diameter dsr12.41.2 22 renewing glass panes, with putty and nails wherever necessary including racking out the old putty:float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm) dsr14.5.1 23 cleaning of chocked sewer line by diesel running vehicle mountinghydraulic operated high pressure suction cum jetting sewer cleaningmachine fitted with pump having 4000 litres suction capacity and 6000 litres water jetting tank capacity including skilled operator, supervising engineer etc. for cleaning and partial desilting of manholes and dechocking of sewer lines. dechocking and flushing of sewer line from one manhole to another by high pressure jetting system of 2200 psi for sewer line from 150 mm dia upto 300 mm dsr 14.77

State Government

TRN :49019854 | 02 Jun, 2025

Tender Value : 0

Lucknow - Uttar Pradesh

Tender for tender for empanellenment of contractors firms for the emergency work of attending breakdown due to failure of insulators snapping of conductor damage of towers in 132 kv and 220 kv transmission lines under electricity transmission central zone, upptcl.

Government Departments

TRN :49019855 | 21 May, 2025

Tender Value : 8.44 Lacs

Agra - Uttar Pradesh

Tender for construction work of zone-1 ward no. 16 ratanpura garib nagar community hall.

Government Departments

TRN :49019859 | 21 May, 2025

Tender Value : 10.21 Lacs

Agra - Uttar Pradesh

Tender for tender for hariparvat zone, room no. 44, c-block, new agra, c.c. road improvement work by. - scrapping of the maxpalt bitumen road etc. all complete. 2 earth work in excavation by mechanical means (hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by engineer-in-charge: all kinds of soil. 3 demolishing brick tile covering in terracing including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. 4 by machenical transport including loading, unloading and stacking of earth (upto 10 km) 5 1:5:10 (1 cement: 5 coarse sand (zone-iii) derived from natural sources: 10 graded stone aggregate 40 mm nominal size derived from natural sources) 6 providing and laying design mix cement concrete of m-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy m.s. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of engineerin-charge (item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately). cement concrete manufactured in automatic batching plant (rmc plant) including transportation to site in transit mixer 7 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in foundation and plinth in: cement mortar 1:4 (1 cement: 4 coarse sand) 8 cement plaster in coarse sand : 12mm cement plaster of mix : 1:4 (1 cement : 4 coarse sand) 9 raising & re-fixing of manhole including all material labor t&p etc. all complete. 10 r.c.c. precast slab 900mm x 450mm having thickness (150mm with 10mm dia) reinforcement double cage and having two lifting handles. 11 supply and fixing of black granite stone board and approved standard matter with brick work, plaster & paint etc. all complete. 12 sub total (a) 13 add / deduction for estimate figure amount match 14 grand total

Government Departments

TRN :49019871 | 21 May, 2025

Tender Value : 8.47 Lacs

Agra - Uttar Pradesh

Tender for tender for repair work of zone-1 ward no. 16 ratanpura nagla vida community hall. - cleaning of the site for warkable etc. all complete. (non scheduled) 2 1:5:10 (1 cement : 5 coarse sand (zone-iii) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) (dsr 2023 sh-4.1.10 ) 3 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in :cement mortar 1:4 (1 cement : 4 coarse sand) (dsr 2023 sh-6.4.1 ) 4 brick work 7 cm thick with common burnt clay f.p.s. (non modular) brick of class designation 7.5 in cement mortar 1:3 (1 cement : 3 coarse sand) in superstructure above plinth level and upto floor five level. (dsr 2023 sh-6.8 ) 5 reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills,taircases and spiral stair cases above plinth level up to floor fiveevel, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).(dsr 2023 sh-5.3 ) 6 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. thermo-mechanically treated bars of grade fe-500d or more(dsr 2023 sh-5.22.6) 7 centering and shuttering including strutting, propping etc. and removal of form work for :columns, piers, abutments, pillars, posts and struts(dsr 2023 sh-4.3.3 ) 8 12 mm cement plaster of mix : 1:4(1 cement: 4 fine sand)(dsr 2023 sh-13.1.1 ) 9 structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.(dsr 2023 sh-10.1 ) 10 providing and fixing 12 mm thick panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick.fire retardant plywood conforming to is: 5509(dsr 2023 sh-9.126.2 ) 11 providing and fixing isi marked is:1341 m.s. pressed butt hinges bright finished with necessary screws etc. complete :)75x47x1.70 mm (dsr 2023 sh-9.55.3 ) 12 providing & fixing decorative high pressure laminated sheet of plain / wood grain in gloss/ matt/ suede finish with high density protective surface layer and reverse side ofdhesive bonding quality conforming to is : 2046 type s including cost of adhesive of approved quality. 1.0 mm thick (dsr 2023 sh-9.127.2 ) 13 distempering with 1st quality acrylic distemper (ready mixed) having voc content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour new work (two or more coats) over and including water thinnable priming coat with cement primer having voc content less than 50 gram/litre (dsr 2023 sh-13.41.1 ) 14 painting steel work with deluxe multi surface paint to give an even shade. two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture(dsr 2023 sh-1021sub head : 13 finishing13.48.3 ) 15 providing & fixing white vitreous china water closet squatting pan (indian type) along with “s” or “p” trap including dismantling of old wc seat and “s” or “p” trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of engineer-in charge. long pattern w.c pan of size 580x440 mm (dsr 2023 sh-14.80.1) 16 providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require white vitreous china flat back wash basin size 450x 300 mm with single 15mm c.p. brass(dsr 2023 sh-17.7.7) 17 providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white pvc automatic flushing cistern, with fittings, standard size c.p. brass flush pipe, spreaders with unions and clamps (all in c.p. brass) with waste fitting as per is: 2556, c.i. trap with outlet grating and other couplings in c.p. brass, including painting of fittings and cutting and making good the walls and floors wherever required(dsr 2023 sh-17.5.1 ) 18 providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white p.v.c. automatic flushing cistern, with fittings, standard size g.i./ pvc flush pipe for back and front flush with standard spreader pipes with fittings, g.i clamps and c.p. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required: single squatting plate with 5 litre p.v.c. automatic flushing cistern(dsr 2023 sh-17.6.1 ) 19 providing and laying flamed finish granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the engineer-in-charge :flamed finish granite stone slab jet black, cherry red, elite brown, cat eye or equivalent.(dsr 2023 sh-11.55.1 ) 20 providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to isi : 12701, colour of opaque white or as approved by engineer-in- charge. the rate includes making necessary holes for inlet, outlet & over flow pipes. the base support i/c fittings & fixtures for tank shall be paid separately 21 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized pvc medium well casing (cm) pipe of required dia, conforming to is: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of engineer -in-charge100 mm nominal size dia 22 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized pvc medium well casing (cm) pipe of required dia, conforming to is: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of engineer -in-charge150 mm nominal size dia 23 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply and all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one stepcpvc solvent cement and testing of joints complete as per direction of engineer in charge. internal work - exposed on wall 15 mm nominal dia pipes 24 providing and fixing ptmt bib cock of approved quality and colour.15mm nominal bore, 86 mm long, weighing not less than 88 gms 25 providing and fixing ptmt stop cock of approved quality and colour.15 mm nominal bore, 86 mm long, weighing not less than 88 gms) 26 mirror of superior make glass 60x45 cm 27 providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete size of tile 600x600 mm 28 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer-in-charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 29 supply and fixing of light fitting switch board. (none sheduled) 30 supply and fixing wiring of light point. (none sheduled) 31 s/l/j of 20mm dia pvc cunduct pipe etc. all complete. 32 supply & fixing of wiring sub main. 33 supply & fixing of plug point 15mm. 34 lettering & painting of wall etc. all complete. 35 supply & fixing of 27watt. cfl etc. all complete. 36 carriage of materials by manual labour including loading, unloading and stacking for lead less than 01-50 mtrm.207.34+30.42 every 50 additonal meter 37 stone tile work for wall lining upto 10 m height with special adhesive over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement with an admixture of pigment to match the stone shade. 7.38.1 8mm thick (mirror polished and machine cut edge) 7.38.1.1 granite stone of any colour and shade 38 constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast r.c.c. horizontal grating with frame complete as per standard design :with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 39 kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick 40 6 mm cement plaster of mix :1:3 (1 cement : 3 fine sand) 41 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.) 42 stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (to be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) :8.14.1 red sand stone - exposed face fine dressed with rough backingt 43 marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with :raj nagar plain 44 providing and fixing stainless steel ( grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)(dsr 2023 sh-10.28 ) 45 1:2:4 (1 cement : 2 coarse sand (zone-iii) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources). (dsr 2023 s h) 46 supply & fixing granite stone work display board (size 2.50ft x 4.00ft) including painting, lettering etc. all complete. (none schedule) 47 sub total 48 add/deduction rs. for estimate figure amount match 49 grand total

Government Departments

TRN :49019874 | 21 May, 2025

Tender Value : 8.45 Lacs

Agra - Uttar Pradesh

Tender for construction work of drain and cc flooring from ramnath house to amit arora house via brahmakumari ashram in loha mandi zone room no. 11 charbagh.

Related Searched Keywords : zone work

List of zone-work Tenders

Tender for tender for supply of mauegs material work ward 14 ward1manadathupady-tharappady road= 1 stone aggregate 2 40 mm nominal size 3 20 mm nominal size 4 10 mm nominal size 5 portland cement 6 coarse sand (zone 3) 7 concrete mix machine 8 display board

Tender for tender for empanellenment of contractors firms for the emergency work of attending breakdown due to failure of insulators snapping of conductor damage of towers in 132 kv and 220 kv transmission lines under electricity transmission central zone, upptcl.

Tender for construction work of zone-1 ward no. 16 ratanpura garib nagar community hall.

Tender for construction work of drain and cc flooring from ramnath house to amit arora house via brahmakumari ashram in loha mandi zone room no. 11 charbagh.

Get zone work Tender Alert...

Related Searched Keywords : zone work

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us