Filters

List of waste-removal Tenders

List of latest waste-removal Tenders in Indian Tenders. Click on any waste-removal Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for waste-removal Tenders.

All-Tenders (67)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

State Government

TRN :49057999 | 23 May, 2025

Tender Value : 0

Ghaziabad - Uttar Pradesh

Tender for tender for construction of civil works for increasing capacity from (1x500 plus 2x315 mva) to (2x500 plus 1x315 mva) at 400 k.v. sub-station-ist muradnagar ghaziabad. - earth work in excavation by mechanical means (hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) all kinds of soil including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by engineer-in-charge. 2 excavating, supplying, stacking and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also includingramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all 3 providing and laying in position cement concrete of specified grade 1:4:8 (1 cement : 4 coarse sand (zone-iii) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)excluding the cost of centering and shuttering - all work up to plinth level : 4 providing and laying in position cement concrete of specified grade 1:5:10 (1 cement : 5 coarse sand (zone-iii) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)excluding the cost of centering and shuttering - all work up to plinth level : 5 providing and laying in position cement concrete of specified grade1:1½:3 (1 cement: 1½ coarse sand (zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) excluding the cost of centering and shuttering - all work up to plinth level : 6 providing and laying in position specified grade of reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand (zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources), excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level : 7 centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete 8 centering and shuttering including strutting, propping etc. and removal of form for walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. 9 centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roofs, landings, balconies and access platform 10 centering and shuttering including strutting, propping etc. and removal of form for columns, pillars, piers, abutments, posts and struts. 11 providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). 12 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. thermo-mechanically treated bars of grade fe-500d or more. 13 brick work in foundation & plinth with old dismantled bricks (supplied by department free of cost) and coarse sand mortar in 1:6 including supply of all other materials, labour, removing mortar & cleaning of old & used bricks,t&p etc complete . 14 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in foundation and plinth in cement mortar 1:4 (1 cement : 4 coarse sand). 15 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in foundation and plinth in cement mortar 1:6 (1 cement : 6 coarse sand). 16 dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with jamuna sand, with common burnt clay non modular bricks 17 supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of engineer-in-charge . 18 structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 19 mild steel or iron work in heavy sizes such as trusses built up gates, door frames, record, racks roof workgates etc. wrought to required form including holes rivetting or welding where necessary and also fixingin proper position and alignment but when steel is to be provided by the department . 20 12 mm cement plaster of mix 1:4 (1 cement: 4 coarse sand). 21 extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturers specification. 22 extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers. 23 neat cement punning 24 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. 25 demolishing cement concrete (nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)) manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer - in - charge. 26 demolishing brick work in cement mortar manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge. 27 dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead. 28 demolishing r.c.c. work by mechanical means and stockpiling at designated locations and disposal of dismantled materials up to a lead of 1 kilometre, stacking serviceable and unserviceable material separately including cutting reinforcement bars. 29 dismantling of existing pale / security / chain link fencing including post and stacking properly as per direction of the engineer - in - charge. including all labour and t&p etc. required for proper completion of the work 30 disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. 31 supply of 25 mm. dia m.s. anchor bolts (conforming to is 266)500 mm. long with base plate (50x50x6mm) welded with anchor boltsincluding its threading upto a length of 10cm. and also supplyof a pair of galvanized standard nuts with threading including supply of 5 mm thick washer and cost of labour, material & t&p for proper completion of work 32 fixing and grouting 25 mmand below dia m.s. anchor bolt in proper alignment level and setout with the help of a template including supply of all labour t&p etc. reqd. for proper completion of the work. (labour rates only) . 33 grouting of 90/105 lbs m.s. railincluding cost of all materials,labour & t&p for fixing of rail in proper alignment, leveland position in transformer plinth foundation etc. as perdirection of eng i/c. (rail to be supplied by thedept.)(labour rates only) . 34 s/f in position 105 lbs m.s. rail for transformer plinth including cost of all labour, material and t&p etc. required for proper completion of the work. 35 fixing and grouting of trench edging in proper level and alignment including cost of all labour, and t&p etc. required for proper completion of the work but excluding cost of c.c. (labour rates only) . 36 fixing of template in position level and alignment for groutingof anchor bolt in auxiliary gantry (labour rate only). 37 fixing of cable trench racks in proper position and alignment including cost of all labour, material and t&petc. required for proper completion of the work (labour rate only). 38 fabrication of template forauxiliary foundation including cost of all labour, and t&p etc. required for proper completion of the work. steel shall be arranged by contractor free of cost. this template shall be property of contractor.(labour rate only). 39 4.0 cm thick 1:1.5:3 plain cement concrete floor with cement, approved coarse sand & 2cm gradedapproved stone ballast laid in panels finished with 3mm floating coat of neat cement or cement andmarble dust in ratio of 5:1 as specified and removing any overlapping mortar at the joints of the panels ifany and giving them a uniform finish including supply of all materials, labour and t&p etc, required forproper completion of the work. without base cc 40 placing of trench cover of all size in proper position including transportation from different places withinthe s/s area including all labour, t&p etc. required for proper completion of the work as per direction ofengineer - in - charge. 41 preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres. 42 providing and laying swr, pvc ( finolex or equivalent ) pipe including cost of excavation, c.c etc including its jointing and connection, all materials, labour and t&p etc. required for proper completion of the work (110mm dia pipe) 43 providing and laying design mix cement concrete of m-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy m.s. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of engineer-incharge (item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately).cement concrete manufactured in automatic batching plant (rmc plant) i/c transportation to site in transit mixer 44 providing and fixing in wall lining flat pressed three layer (medium density) particle board or graded wood pre-laminated one side decorative lamination and other side balancing lamination grade i, type ii, is : 12823 marked, including priming coat on unexposed arrangement and screws etc. complete : (12mm thick partical board) 45 hiring of beldar(labour).

Central Government And Public Sector

TRN :49059263 | 17 May, 2025

Tender Value : 14.93 Lacs

Howrah - West Bengal

Tender for tender for structural strengthening and external painting of b e college t e howrah; 1 demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer - in - charge. 2 nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) 3 dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : 4 of area 3 sq. metres and below 5 dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. 6 for thickness of tiles 10 mm to 25 mm 7 dismantling c.i. pipes including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means breaking lead caulked joints, melting of lead and making into blocks including stacking of pipes & lead at site within 50 metre lead as per direction of engineer-in-charge: 8 up to 150 mm diameter 9 dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. 10 disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. 11 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level : 12 1:2:4 (1 cement : 2 coarse sand(zone-iii) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) 13 reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 14 1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii)derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) 15 reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii)derived from natural sources : 3 graded stone aggregate 20 mm nominal sizederived from natural sources). 16 reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers, facias and eaves boards above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii)derived from natural sources : 3 graded stone aggregate 20mm nominal size derived from natural sources). 17 centering and shuttering including strutting, propping etc. and removal of form for : 18 foundations, footings, bases of columns, etc. for mass concrete 19 columns, pillars, piers, abutments, posts and struts 20 vertical and horizontal fins individually or forming box louvers band, facias and eaves boards 21 small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like 22 smooth finishing of the exposed surface of r.c.c. work with 6 mm thick cement mortar 1:3 (1 cement : 3 fine sand). 23 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer-in-charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 24 providing and fixing fiber glass reinforced plastic (frp) door frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. the laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. the frame shall be covered with fiber glass from all sides. m.s. stay shall be provided at the bottom to steady the frame. 25 providing and fixing to existing door frames. 26 30 mm thick glass fibre reinforced plastic (frp) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick frp laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick frp laminate for panels conforming to is: 14856, including fixing to frames. 27 steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 28 in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. 29 providing and laying rectified glazed ceramic floor tiles of size 300x300mm or more (thickness to be specified by the manufacturer), of 1stquality conforming to is : 15622, of approved make, in colours white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4(1 cement: 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. 30 providing and fixing on wall face unplasticised - pvc moulded fittings/accessories for unplasticised rigid pvc rain water pipes conforming to is 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion. 31 single tee with door -110x110x110 mm 32 bend 87.5° -110 mm bend 33 15 mm cement plaster on the rough side of single or half brick wall of mix : 34 1:6 (1 cement: 6 fine sand) 35 finishing walls with acrylic smooth exterior paint of required shade : 36 new work (two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) 37 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: 38 two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. 39 removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 40 dismantling w.c. pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of engineer-in- charge. 41 providing and laying app (atactic polypropylene polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the samemembrane manufactured of density at 25°c, 0.87 - 0.89 kg/litre and viscocity 70 - 160 cps. over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. the vital physical and chemical parameters of the membrane shall be as under : joint strength in longitudinal and transverse direction at 23°c as 350/300 n/5 cm. tear strength in longitudinal and transverse direction as 60/80n. softening point of membrane not less than 150°c. cold flexibility shall be upto -2°c when tested in accordance with astm, d - 5147. the laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane : 42 3 mm thick 43 providing and fixing white vitreous china pedestal type (european type/ wash down type) water closet pan. 44 providing and fixing p.v.c. low level flushing cistern with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete. 45 10 litre capacity - white 46 providing and fixing solid plastic seat with lid for pedestal type w.c. pan complete : 47 white solid plastic seat with lid 48 providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively. 49 providing and fixing p.v.c. waste pipe for sink or wash basin including p.v.c. waste fittings complete. 50 flexible pipe -32 mm dia 51 providing and fixing ptmt bib cock of approved quality and colour. 52 15mm nominal bore, 86 mm long. weighing not less than 88 gms. 53 providing and fixing ptmt stop cock of approved quality and colour. 54 15 mm nominal bore, 86 mm long. weighing not less than 88 gms. 55 providing and fixing ptmt pillar cock of approved quality and colour . 56 15mm nominal bore, 107 mm long. weighing not less than 110 gms. 57 providing and fixing unplasticised p.v.c. connection pipe with ptmt nuts, collar and bush of approved quality and colour. 58 15 mm nominal bore with 45 cm length. 59 chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of engineer-in-charge 60 75 mm average thickness 61 50 mm average thickness 62 25 mm average thickness 63 cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of engineer-in-charge. 64 bars upto 12 mm diameter 65 bars above 12 mm diameter 66 providing, mixing and applying bonding coat of approved adhesive on chipped portion of rcc as per specifications and direction of engineer-in-charge complete in all respect. 67 sbr polymer (@10% of cement weight) modified cementitious bond coat @ 2.2 kg cement per sqm of surface area mixed with specified proportion of approved polymer 68 providing, mixing and applying sbr polymer (of approved make) modified cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of engineer-in-charge. note: measurement and payment: the pre-measurement of thickness shall be done just after the surface preparation is completed and payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 n/sqmm2). 69 12 mm average thickness. 70 25 mm average thickness in 2 layers. 71 50 mm average thickness in 3 layers. 72 providing and fixing upvc pipes (sch 40 upvc as per astm d- 1785 pipes) including all upvc plain and brass threaded fittings. including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step upvc solvent cement and testing of joints complete as per direction of engineer in charge. internal work- exposed on wall 73 15 mm nominal bore 74 20 mm nominal bore 75 25 mm nominal bore 76 uprooting and removing small plants from the surface of walls, parapet, etc. at any height by cutting chase for removing roots and using necessary chemicals etc. to prevent further growth of plants and mending good damages complete. 77 a) small plant of girth of exposed stem up to 75mm 78 providing and fixing soil waste and vent pipes : 79 110 mm dia upvc soil waste pipe conforming to is:13592 1992 (type-b) manufactured by supreme industries limited or equivalent. 80 erection of single layer bamboo-scaffolding made of average 75 mm dia bamboos with adequate bracing, ties, ropes etc. for strong, stable and workable scaffolding for specified jobs ( above gf beyound 4.00m height) like replacement of sewage/ rw pipes & accessories, repairs to plasters, special repairs, replacement of glass panes, uprooting/ cutting of tree saplings etc including dismantling the scaffolding after the job is done and clearing the site complete as per the direction of the engineer-in-charge. [ projected area of scaffolding frame work on buiding elevation to be measured for payment] 81 felling of trees like banyan, pipul etc from compound walls, building walls, cornices etc by making scaffolding where necessary including cutting of trunks and branches, application of chemicals/weedicides to the remaining portion to kill the growth of tree and ultimately removing the roots from the walls by cutting walls and mending good complete. ( the rate is inclusive of the mending good the walls with bricks/concretes/plasters and disposing of branches/trunks to vats inside compound for further disposal) 82 a) of girth above 30 cm upto 60 cm (measured above 1.0 m from gl toupto 5.0 m height) 83 extra for shifting of existing scaffolding by lifting/dragging or partially dismantling and re-erecting the dismantled portion in position (shifting at least 1.50 m from initial centre line of position) over payment for initial erection & dismantling paid in original item of scaffolding. [ projected area of scaffolding frame work on buiding elevation to be measured for payment] 84 providing and fixing ptmt health faucet with hook and p.v.c. pipe (1.00 metre minm length) of approved quality and colour in w.c.s all complete as per direction of engineer-in-charge. 85 15 mm nominal bore with minimum 1.00 m pvc tube. 86 attending repairs to ms gate by removing corroded portion of gate with welding machine at site and replacing with new members as per actual requirement at site. (cost for labour and hire charges of welding machine including transporation, consumables. steel members will be paid separately) 87 providing and welding 2mm thick m.s. sheet to existing m.s. frame work including providing and appying a priming coat of approved steel primer all complete. 88 providing and fixing upvc floor trap 100mm dia inlet and 100 mm dia outlet. 89 providing and fixing ptmt 2 way bib cock of approved quality and colour, for fixing hand faucet in commode toilets all complete as per direction in charge.- 15mm nominal bore. 90 supplying, fitting and fixing in position fibre glass panes of approved quality with resin, nail, clip etc. as per is:12866-1989. 91 4.0 mm thick (6.72 kg/sq.m) 92 credit value for dismantled unserviceable mild steel/ iron materials. 93 credit value for dismantled g.i. pipes: 94 15 mm nominal dia. 95 20 mm nominal dia. 96 25 mm nominal dia. 97 credit value for dismnatled c.i./ s.c.i. pipes. 98 credit value for unserviciable brass bib/stop cocks/pillar tap

State Government

TRN :49062033 | 13 May, 2025

Tender Value : 2.34 Lacs

Paravur - Kerala

Tender for tender for pakarappally devaswom - paravur group - constructing toilet block-- 1 appendix i-constructing toilet block 2 earth work in excavation by mechanical means (hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.all kinds of soil 3 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size) 4 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level:1:1/2:3 (cement : 11/2 coarse sand : 3 graded stone aggregate 20 mm nominal size) 5 centering and shuttering including strutting, etc. and removal of form for:foundations, footings, bases of columns, etc for mass concrete 6 solid block masonry using pre cast solid blocks (factory made) of size 30x20x15 cm or nearest available size confirming to is 2185 part i of 1979 for foundation and plinth with thickness 15cm in: cm 1:6 ( 1 cement :6 coarse sand) etc complete 7 providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size 8 steel reinforcement for r.c.c work including straightening, cutting, bending, placing in position and binding all complete upto plinth level thermo - mechanically treated bars of grade fe-500d or more 9 solid masonry using pre cast solid blocks (factory made) of size 30x20x15cm or nearest available size confirming to is 2185 part i of 1979 for super structure up to floor two level with thickness 15cm in : cm 1:6 ( 1 cement : 6 coarse sand) etc complete 10 reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 150 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (zone iii) : 3 graded stone aggregate 20 mm nominal size). 11 centering and shuttering including strutting, etc. and removal of form for:lintels, beams, plinth beams, girders bressumers and cantilevers 12 steel reinforcement for r.c.c work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelthermo - mechanically treated bars of grade fe-500d or more 13 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) 14 providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.size of tile 600 x 600 mm. 15 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineerin-charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 16 providing and fixing water closet squatting pan (indian type w.c. pan) with 100 mm sand cast iron p or s trap, 10 litter low level white p.v.c.flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever require:white vitreous china orissa pattern w.c. pan of size 580x440 mm with integral type foot rests 17 supplying and fixing cp towel rod 45cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site engineer-in-charge. 18 providing and fixing white vitreous china pedestal type water closet (european type w.c. pan) with seat and lid, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:w.c. pan with isi marked white solid plastic seat and lid 19 providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:white vitreous china flat back wash basin size 550x400mm with single 15 mm c.p.brass pillar taps 20 finishing walls with acrylic smooth exterior paint of required shade:new work (two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 21 supply and fixing pvc door with frame including locking arrangements as per the direction of engineer-in-charge 22 providing and fixing m.s. grills of required pattern in frames of windows etc. with m.s. flats, square or round bars etc. including priming coat with approved steel primer all complete.fixed to openings/ wooden frames with rawl plugs screws etc 23 providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per is: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by engineer-in-charge. the sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with epdm seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 24 structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 25 providing and placing on terrace (at all floor levels) polyethylene water storage tank :isi 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 26 supplying and fixing cp health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge. 27 providing and fixing c.p brass bib cock of approved quality conforming to is: 8931.15 mm nominal bore 28 providing and fixing c.p. brass shower rose with 15 or 20 mm inlet:100 mm diameter 29 appendix ii-septic tank and soak pit 30 supplying and installing ready made pvc septic tank including the cost of carriage, trenching, placing at the level below ground level as specified as per the direction of engineer in charge (provision for cc/rcc/sand/06mm aggregate for the preparation of bed shall be paid separately. 4.35 to 50 flush capacity

Central Government And Public Sector

TRN :49067554 | 24 May, 2025

Tender Value : 0

Longding - Arunachal Pradesh

Tender for removal of legacy waste through bioremediation and bio-mining process to reclaim the existing dump yard situated in khonsa city on design, building, finance, own and operate model

Central Government/Public Sector

TRN :49068676 | 28 May, 2025

Tender Value : 20.00 Lacs

Bikaner - Rajasthan

Tender for tender for welcome maintenance to officers md accommodation at af station nal; 1 demolition of brick or stone masonary built in cement mortar incl all quoins, arches, pillar etc. complete all as specified and directed. 2 material and labour brick work with sub class -b bricks old size, straight or curved on plan exc 6m mean radiusbuilt in cm 1:6. complete all as specified & directed. 3 all as per serial item no. 2.00 (here in before) but as in half brick thick walls built in cement mortar 1:4. 4 taking down chawkhat or frame with shutter (without taking off shutters from the frames) not exc 1.5 sqm each complete all as specified and directed. 5 taking down chawkhat or frame with shutter (without taking off shutters from the frames) exc 1.5 sqm but not exc 4.0 sqm each complete all as specified and directed. 6 taking down door shutter of any description exc 1.00 sqm but n. exc. 2.00 sqm each complete all as specified and directed. 7 taking down wooden shutters of any description exc 1 sqm but n.exc 2 sqm each from chowkhat and re-fixing in same opening after re-securing or easening and adjusting including repair of hinge as required complete all as specified and directed. 8 s&f solid pvc door frame of size 50mm x 47mm made out 5mm both side prelam pvc sheet used instead of plain colour pvc sheet & edges will be painted to match with prelam sheet re-inforced with ms square tube complete all as specified and directed. 9 m&l for factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of ms tubes 40mm x 20 mm for top and bottom rails ms frame shall be covered with heat moulded prelam pvc ‘c’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam colour pvc sheets for top rail lock rail & bottom rail on either side and as gap insert for top rail & bottam rail both side prelam pvc sheet used instead of plain colour pvc sheet. stile and rails feathered at edges paneling of prelam solid pvc sheets 10mm thick to be filted in msframe 40 x 20 mm welded, sealed to the stiles and rails with suitable pvc sheet beading, and jointed together with the solvent cement complete all as specified and directed. 10 s&f 1.25 mm thick pressed steel frames of size 125mm x 60mm for double doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including filling back hollow with pcc 1:3:6 type c-0 using 12.5 mm graded stone aggregate complete all as specified and directed. 11 s&f 1.25 mm thick pressed steel frames of size 105mm x 60mm for double doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including filling back hollow with pcc 1:3:6 type c-0 using 12.5 mm graded stone aggregate complete all as specified and directed. 12 s&f 35 mm thick 2nd class hard wood factory made plain framed, pannelled shutter (any number of panels) with panel of timber flat on both sides (feather edged) or of 12mm thick bwp commercial plywood with commercial face veneers, supplied and fitted complete all as specified and directed. 13 supply and fixing glazed and gauged skeleton factory made shutters35mm thick, 2nd class hard wood hollockopen rebated and prepared to receive glass, gauge etc (with sash bars) edges of framing plain chamfered or rounded fitted with cutand mitred beads for securing glass etcincl priming coat. the size of member of shutters as spfd in ssr part-1 section 8 clause 8.20 (b) incl kiln seasoned and chemically pressure treated, complete all as specified & directed. 14 s&f30mm factory made thick flush shutters, solid core construction,with particle board coreand plywood face panels,commercial type on both face is covered with decorative face veneer with lipping/frame to match sides includeforthe provision of suitable blocks for taking mortice locks, latches, or other fittings complete all as specified and directed. 15 s&f butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised, 100mm size, isi marked, complete all as specified & directed. 16 supply and fixing200mm size aluminium anodised barrel tower bolts of extruded section, complete all as specified and directed. 17 supply and fixing 150mm sizeextruded aluminium alloy handles, fabricated type, anodised aluminium handles, complete all as specified and directed. 18 supply and fixing 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified & directed. 19 supply& fixingas in repairfloor door stopper of aluminium alloy body and tongue, overall length of cover plate 140 mm anodised with hard drawn steel spring, fixed to door shutters,complete all as specified and directed. 20 supply and fixing galvanised stainless steel wire cloth 0.45mm nominal dia of wire and width of aperture 1.40mm and fixed with tinned tacks or galvanised wire stapples/ screws in metal surrounds as required fixedcomplete all as specified and directed. 21 all as per description of serial item no. 20 here in before but as in repair 22 hacking out old broken glass of any thickness/size of any description from wooden frames/metal frame glazed with putty or fixed with beads all as specified. 23 supply and fixing 3mm thick sheet glass, ordinaly quality and glazing with oil putty or secured with spring clips in metal surrounds as required in square n exc 0.5 sqm in each pane , complete all as specified and directed. 24 all as per description of serial item 23 here in before but figured glass, pin head type. 25 s&f as in repairs door closer hydraulically regulated cast iron body, designation no 2, universal type, suitable for door shutters of size 701 to 850 mm in width and of weight between 36 to 60 kg,complete all as specified and directed. 26 s&f as in repair mild steel 300mm, ordinary rat tail rod pattern springs, including roller and roller pleat complete all as specified and directed. 27 s&f in repair stainless steel (grade 305) curtain rods 25mm dia 0.80mm wall thickness mild steel chromium plated incl supporting brackets complete all as specified and directed. 28 s&f in repair stainless steel (grade 305) ornamental type brackets (open ends) suitable for curtain rods of 25mm dia all as specified and directed. 29 s&f in repair stainless steel (grade 305) brackets (dead ends) suitable for curtain rods of 25mm dia all as specified and directed. 30 demolition of cement concrete in any positionand removing the rubbish outside mod land complete all as specified anddirected. 31 m&l for pcc (1:3:6) type c-2, using 40mm graded stone aggregate as in plinth protection 75mm thick laid in bays including all necessary form work, finishing exposed edges fair and providing 10 mm wide joints throughout the thickness of plinth protections duly filled with matic filling(one part of hot bitumen 85/25 and three parts of sand)and surfaces finished even & smooth without using extra cement complete all as specified . 32 m&l 25mm thick pcc 1:2:4 type b-0(using 12.5mm graded stone aggregate)as in sub base of floor surface finished even rough to receive floor topping complete all as specified and directed. 33 dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc.laid bedded and pointed in any mortar complete all as specified and directed. 34 m&l for granite (of any type)slab 18-20 mm thick machine cut ,bedded and jointed with gray cement slurry and pointed with white cement as in floors/ cooking plateform, with admixiture of pigment to match the shade of granite stone including grindingand polishing complete over and including20 mm thick screed bed in cm 1:6 complete all as specified . 35 m&l for granite (of any type)slab 18-20 mm thick machine cut , jointed with gray cement slurry and pointed with white cement as in vertical surfaces / dado / skirtingwith admixiture of pigment to match the shade of granite stone indluding grindingand polishing complete over and including10 mm thick backing coat in cm 1:4 complete all as specified . 36 m& l green marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade, including grinding and polishing providing edge moulding to 18-20mm thick stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete complete complete all as specified and directed. 37 dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) and rubbish off the premises complete all as specified. note:-the demolished material should be disposed off out side the mod land. the contractor shall quote his rates considering the above element 38 material and labour for glazed ceramic coloured tiles 7 to 8mm thick (square/rectangular )in vertical surface area of each tile exceeding 0.13 sqm but not exceeding 0.18 sqm thick set & jointed in neat gray cement slurry and pointed with coloured cement to match,the sahde of tiles laid over and including 10mm thick rendering in cm 1:4 complete all as specified and directed. 39 material and labour non-skid, ceramic coloured tiles 7 to 8mm thick (square/rectangular ) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm,as in floors, set and jointed ingray cement slurry and pointed in white or coloured cement to match with the shade of tiles laid over and including 15mm thick screed bed or bedding layer in cm 1:6 as specified and directed. 40 material and labour non-skid, ceramic, coloured tiles 7 to 8mm thick (square/rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,as in floors, set and jointed ingray cement slurry and pointed in white or coloured cement to match with the shade of tiles laid over and including 15mm thick screed bed or bedding layer in cm 1:6 as specified and directed. 41 material and labour non-skid, ceramic, coloured tiles 7 to 8mm thick (square/rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in skirting, set and jointed ingray cement slurry and pointed in white or coloured cement to matchthe shade of tiles laid over and including 10mm thick backing coat on fair faces of brick work or concrete surface in cm (1:4) complete all as specified and directed. 42 m&l for vitrified light shade ceramictiles9 to 10 mm thick polished,area of each tile exc 0.18 sqm andn exceeding 0.36 sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in cm 1:6 complete all as directed by engr-in-charge. 43 all as per ser item no.42 (here in before) but as in skirting laid over and including 10mm cement backing in cm 1:4. 44 material and labour for repairing of soffits of slabs/chajja, facia and similar works by dismantling of loose/ disintegrated portion of rcc upto 7.5 mtr heightand in any sitution, including provn of support,formwork and welding of reinforcement and fixing in position and with provision of weld mesh, applying dubbing 1st coat of 20 to 25mm thick in cm 1:3 finished rough and finishing coat of 10mm thick in cm (1:3) finished even and smooth without using extra cementover and including cement slurry @ 3 kg/sqm, finished even and smooth to desired shapeand applyingtwo coats of weather proof exterior emulsion paint over a coat of arylic resistant primer to match with existing surfaces complete all as specified and directed.(weld mesh measured and paid sepatrtely)note:-(i) unit rate of this item includes the cost of scaffolding, formwork etc. and nothing extra shall be paid on account of variation in height.(ii) for payment purpose, the area of finished plaster in 2nd coat shall be considered. 45 material and labour for hard drawn steel wire fabric (weld mesh) of weight not less than 3 kg/ sqm and not exc 4 kg/ sqm cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcemnt including necessary fixing arrangements etc complete all as specified and directed. 46 taking down cementplaster of any description on brick wall surfaces etc including raking out joints hacking for key , scrubbing down down with water etc complete all as specified and directed. note:- the demolished materials should be disposed off at a site as described by the eng-in-charge. the contractor shall quote his rates considering the above element. 47 m&l for rendering 10 mm thick on ceiling (brick or concrete surfaces)in cement mortar 1:4 and surface finished even and smooth without using extra cement complete all as specified and directed. 48 m&l for rendering 15mm thick on brick or concrete surfaces in cement mortar 1:6, finishing surfaces even and smooth without using extra cement complete all as specified and directed. 49 m&l forrendering 15mm thick on brick or concrete surfaces other than fair face of brick work in cement mortar 1:4, finishing surfaces even and smooth without using extra cement complete all as specified and directed. 50 m&l for applying three coats of white wash on newly plasteredsurfaces of ceiling including preparation of surfaces complete all as specifed and directed. 51 m&l for preparation of newly plastered or unplastered surfaces of walls and applying two coats of exterior acrylic emulsion in any pattern (approved by ge), paint over and including a coat of exterior primer complete all as specified and directed. 52 m&l for preparation of newly plastered or unplastered surfaces of walls and applying two coats of oil emulsion distemper white or tinted over and including a coat of primer complete all as specified and directed. 53 material & labour for prepapration of new or previously untreated surfaces of wood or wood based materials of any description not otherwise described over 10cm width or girth & applying two coats of synthetic enamel paint over & including a coat of pink primer comlplete all as specified and directed. 54 material & labour for prepapration of new or previously untreated steel or iron surfaces of any description not otherwise described over 10cm width or girth & applying two coats of synthetic enamel paint over & including a coat of red oxide primer comlplete all as specified and directed. 55 material and labour for preparation of plastered or unplastered old decorated surfaces of walls incl pillasters and cornices etc. incl brooming down with steel wire brushing scrapping down smoke soot moulds moss and efflorescence salts and trading oil and grease spot, washing etc. and applying one coat of white lime wash complete all as specified. 56 material and labour for preparation of plastered or unplastered old decorated surfaces of ceiling etc. incl pillasters and cornices etc. incl brooming down with steel wire brushing scrapping down smoke soot moulds moss and efflorescence salts and trading oil and grease spot, washing etc. and applying one coat of white lime wash complete all as specified. 57 material and labour for preparation of plastered or unplastered old decorated surfaces of walls incl pillasters and cornices etc. incl brooming down with steel wire brushing scrapping down smoke soot moulds moss and efflorescence salts and trading oil and grease spot, washing etc. and applying one coat of oil bound distemper complete all as specified & directed. 58 material and labour for comple removal ofold decorated surfaces of walls incl pillasters and cornices etc. incl brooming down with steel wire brushing scrapping down smoke soot moulds moss and efflorescence salts and trading oil and grease spot, washing etc. and applying two coats of oil bound distemper complete all as specified & directed. 59 m&l for complete removal of existing treatment on walls and applying two coat ofoil bound distempe paint interior gradeover & including a coat of alkali resistant priming paint over 7 including two layer of birla wall putty (min thickness 3mm) incl filling in craks etc to achieve a uniformsmooth finish incl preparationof surfaces complete all as specified & directed . 60 material and labour for preparation of plastered or unplastered old decorated surfaces of walls incl pillasters and cornices etc. incl brooming down with steel wire brushing scrapping down smoke soot moulds moss and efflorescence salts and trading oil and grease spot, washing etc. and applying one coat of plastic emulsion complete all as specified & directed. 61 m&l for preparation of old painted surface of wood and wood based materials of any description not otherwise described over 10 cm. width or girthshallapplying one coat of synthetic enamel painting overthe wooden surfaces all as specified & directed. 62 m&l for preparation of old painted surfaces of steel and iron work of any description exc 10 cm width or girth applying one coat of synthetic enamel paint on steel surface all as specified. 63 taking up or down 15 mm bore steel tubing & connections including clearing for refixing or removal to store complete all as specified and directed. 64 all as perserial item 63 here in before but 20m bore tubes 65 supply and fixing15mm bore tubes “medium grade”, galvanized, with and including all fittings and fixed completetowalls and ceilings or laid in floors,complete all as specified and directed. 66 all as per serial item 65 here in before but 20m bore tubes 67 s&f as in repair pillar taps long body fancy type quarter turn with capasten head chromium plated screwed down high pressure with without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed. 68 supply and fixing as in repairs bib cock quarter turn cast copper alloy chromium plated, fancy type, long body screwed for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed. 69 s & f as in repairs two way angle cock quarter turn cast copper alloy 15 mm bore chromiun plated fancy type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unioin fixed complete all as specified and directed. 70 s & f as in repairs angle cock quarter turn cast copper alloy 15 mm bore chromiun plated fancy type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unioin fixed complete all as specified and directed. 71 supply and fixing as in repair central hole basin mixer long swang nack, without poup waste system with 450mm long copper pipes and brass nuts, cast copper alloy, chromium plated, screwed for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed. 72 supply and fixing as in repair central hole sink mixer long body swang nech for mixing hot & cold water, cast copper alloy, chromium plated, screwed for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed. 73 s&f as in repair brass cp wall mixer 3-in-1 system with provision for both hand shower and over head shower complete with 115mm long bend pipe, connecting legs and wall flange for mixing hot and cold water screwed down for iron pipe 15 mm complete all as specified and directed. 74 s&f as in repair brass cp wall mixer 2-in-1 system with provision for over head shower complete with 115mm long bend pipe on upper side, connecting legs and wall flange for mixing hot and cold water screwed down for iron pipe 15 mm complete all as specified and directed. 75 supply & fixingas in repair chromium platedshower rose with or without swivel joints 125mm dia including fixing to steel pipe,complete all as specified and directed. 76 supply& fixing as in repair toiletpaper holder of brass chromium plated, complete all as specified and directed. 77 supply& fixing as in repairs pvc (ptmt) float valve,high pressure of ptmt with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed suitable for 20mm bore pipe,complete all as specified and directed. 78 supply& fixing as in repairs pvc waste down pipeof 32/40 mm bore for basin, complete all as specified and as directed. 79 supply and fixing as in repairs 15mm dia pvc connection of length 450 mm, with ptmt nut, complete all as specified and directed. 80 supply and fixing as in repairs faucet health (hand jet) 15mm bore cast copper alloy, chromium plated with flexible chromium plated connection pipe 1.5 mtr length, with fittings, complete all as specified and directed. 81 supply& fixingas in repairs wash hand basin, vitreous china, white, decorative type, flat or angleback, size 580mm x 450mm inclusive ofwaste pipe and brass coupling and including cutting for and pinning in ends of brackets or erecting stand and inclusive of cost of brackets complete all as specified and directed. 82 s&f as in repair vitreous china pedastal pattern, wc incl connection to trap, and to flushing pipe anti-syphonage pipe, etc. complete all as specified and directed. 83 s&f in repair rimless single piece wc with uf soft close slim seat cover, hinges, fixing accessories set , incl cisternfittings, size 385x720x715mm complete all as specified directed by engr-in-charge. make: jaguar/cera/hindware 84 supply and fixing as in repair pvc valve less syphonic action type flushing cistern low level white with pvc in let ball valve, float and handle, 10 ltrs capacity and connection to pipes including pvc connection and 32mm dia pvc long bend for squat pattern etc, set with concrete and making good to floor including taking down existing, fixed as in repairs complete all as specified & directed. 85 s&f as in repair ptmt seat cover white colour for padastal pattern,incl connection nut & bolts, etc. complete all as specified and directed. 86 s&f as in repair sinks with drain board made of stainless steel sink of 1mm thick sheet, kitchen or laboratory with plug washer and waste pipe incl bedding in cement mortar 1:6 on to draft wall of including fixing cantilever brackets and connecting unions overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm fixed as in repairs complete all as specified. 87 supply& fixingas in repair pvc bath cabinet, size 622mm x 422mm, comprising of lookingglass, space for bath soaps, shampoo, tooth brush and paste, hand towel rail, complete all as specified and directed. 88 supply and fixing in repair stainless steel towel rack 600mm long with lower hangers incl 3 hooks complete all as specified and directed. 89 supply and fixing in repair brass chromium plated tubular towel rail 20mm dia d type 60 cm long between flanges complete all as specified and directed. 90 supply and fixing as in repair soap dish chromium plated of size 100 x 100 mm any type, fixed with chromium plated brass screwscomplete all as specified and directed. 91 s & f as in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets, bracket guard and railing 60cm long incl screws, complete all as specified and directed. 92 s&f as in repairs corner glass shelf with cp brackets (3 pcs set having size 8,10 & 12)complete all as specified and directed. 93 demolition and breaking up drain pipes 110/75 mm bore (salt glazed ware, ac or reinforced concrete) set in cement mortar complete all as specified and directed. 94 s&f 110mm dia pvc (swr) pipes single socketed in any length with rubber ring joints fixed to wall &laid in trenches or in floors,including clamps as required, complete all as specified and directed. 95 s&f 75mm dia pvc (swr) pipes single socketed in any length with rubber ring joints fixed to wall &laid in trenches or in floors,including clamps as required, complete all as specified and directed. 96 s&f in repair 75mm dia pvc (swr) floor trap plain with cp grating including jointing with solvant cement incl necessary pcc & form work as required complete all as specified and directed. 97 s&f 75mm dia pvc (swr) bends with rubber ring joints fixed as required with oval access door complete all as specified and directed. 98 s&f 110mm dia pvc (swr) bends with rubber ring joints fixed as required with oval access door complete all as specified and directed. 99 s & f 110mm bore pvcswr junction single (single t) with access door complete all as specified and directed 100 s&f in repairs stainless steel plate rack of size 78cmx91cmx25cm made out of 0.80 mm thick of stainless steel sheet , fixed in wall with rawl plugs and screws complete all as specified and directed. 101 dismantling boarding, any description any size , fixed in any position with screws complete all as specified . 102 m& l for 18 mm thick pvc board celuka ply of density 600kg/cum one side prelam/rigid laminated (colour/shade as approved by engr-in-charge) and other side plain white colour to make kitchen cabinet shutters /shelves/partitions and incl all required brackets ss screws etc, approved by engr-in-charge. 103 m& l for 18 mm thick pvc board celuka ply of density 600kg/cum both sidesplain white colour to make kitchen cabinet shutters/shelves/partitions and all required brackets ss screws etc, approved by engr-in-charge. 104 s&fin repair auto closes clip on cabinet hinges (regular) for kitchen cabinet shutters note : each pair means one piece fixed on openable shutter and other piece fixed on fixed portion. 105 s&fin repair stainless steel (ss 304) handles 100 mm size for kitchen cabinet shutters. 106 s&fin repair ball bearing drawer channel telescopic type (500mm) full extention load of load bearing capacity 45 kg.note : each pair means 2 nos of telescopic channel, one piece fixed on left side and another piece fixed on right side. 107 s&f rab door seal bottom brush duststopper with aluminium plate nylone brush of selected colour for fit each complete all as specified and directed. note : the sample of item shall be approved by ge before placing at site 108 supply and fixing powder coated aluminium (minimum thickness of powder coating 50micron) work for frames of doors, windows,ventilators and partitions (fixedportions) with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is: 733 and is:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, c.p. brass/ stainless steel screws, all complete as per architectural drawings and the directions of engineer-in-charge note:-for payment purpose weight of aluminium section will only be measured 109 providing and fixing powder coated aluminium (minimum thickness of powder coating 50 micron) work for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of epdm rubber/ neoprene gasket required (fittings such as hinges,handle,tower bolt,sliding boltshall be paid for separately) with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is: 733 and is:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, c.p. brass/ stainless steel screws,rollers & dust proof brush for sliding door / windowcomplete all as per architectural drawings and the directions of engineer-in-charge note:-for payment purpose weight of aluminium section will only be measured 110 s & f as aluminium grill of size, 85mm x 85mm hexagonal shaped mesh, fixed to aluminium frame work with u clip of size 15mmx12mm & fastners complete all as specified and directed. 111 s & f4.80 mm thick sheet glass ofordinary quality plain / tintedand glazing with rubber beads, clips etc complete all as specified and directed. 112 s & f 3 mm thickhigh quality, durable acrylic panel sheet and glazing with rubber beads, clips etc complete all as specified and directed. 113 s & f double action floor door spring hydraulically regulated made up minimum1.25 thick aluminium alloy sheet foundation box, main body stainless steel cover, with governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified 114 s&f conceled lock (push to unlock) for sliding window made with zinc body, aluminium hook and anti rust material with power coated metallic finish of approved colour having size100mm x 24 mm incl necessary cutting for fixing all as specified and directed.

Central Government/Public Sector

TRN :49068734 | 28 May, 2025

Tender Value : 40.00 Lacs

Bikaner - Rajasthan

Tender for tender for certain repair to buildings of wsa at af stn nal; 1 demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for allas specified and directed. 2 m&l for cement concrete type d2 (1:4:8) ( 40 mm graded crushed stone aggreagte) as filling and mass concretecomplete all as specified and directed. 3 m&l for laying 100mm thick cement concrete type b-1(1:2:4) ( 20 mm graded crushed stone agg)as in floor and paving surfaces all as specified and directed. 4 demolition of brick workor stone/boulders masonary, built in cement mortar or cement lime mortar including all quions, arches, pillars etc. and rubbish materials remove from site all as specified and directed 5 m&l for brick work with sub class b bricks (old size) straight or curved on plan exc 6m mean radius built in cm (1:6) complete all as specified and directed by engr-in-charge. 6 taking down cement plaster of any description on brick/stone walll incl raking out joints hacking for keyscrubbing down water all as speicifed. 7 m&l for rendering 15 mm thickin cement plaster (1:6) on fair faces of brick/concrete surface, finishing even and smooth w/o using extra cement etc. 8 m&l for rendering 15mm thick in cement mortar (1:4) on brick or concrete wall surface finished even and smooth without using extra cement. 9 m&l for preparing newly plastered wall surfaces and applying two coats of weather proof exterior emulsion over and including one coat of primer complete all as specified and directed by engr-in-charge. 10 m&l for preparation of newly plastered surfaces of wallsand applying two coats of oil bound distemper over and including a coat of primer incl etc. complete all as specified and as directed. 11 m&l for preparation of old decorated surfaces of walls (plastered or un plastered) including cornices, pilaster etc by brooming down with steel wire brushing, scrapping down, smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc including filling the depressions with cement based wall care putty and applying one coat of oil bound distemper complete all as specified and directed. 12 m&l for preparation of old painted surface ofwall surface and applying one coat ofweather proof exterior emulsion in camouflage pattern to match the existing pattern complete all as specified and diricted by engineer-in-chare. 13 rough excavation not exceeding 1.5 m deep and getting out in soft/loose soil complete all as specified . 14 removing excavated material exc. 1.50 km but n exc. 5 km and depositing where directed at a level n.exc 1.5m above starting point complete all as specified and directed by engr-in-charge. 15 forming embankments including raising (or lowering) earth, spreading in layers n exc. 30 cm thick; watering, ramming/rolling and finishing to required size, shape, etc., n exc. 1.5 m high from base complete all as specified and directed by engr-in-charge. 16 allas per item no-15 (here-in-before) but 1.5m to 3m height from base completeall as specified and directed by engineer-in-charge. 17 allas per item no-15 (here-in-before) but 3m to 4.5m height from base completeall as specified and directed by engineer-in-charge. 18 allas per item no-15 (here-in-before) but 4.5m and above height from base completeall as specified and directed by engineer-in-charge. 19 dismantling posts or struts in natural ground (wood, steel or r.c.c.) any section, including taking out embedded portion and making good disturbed groundcomplete all as specified and directed by engr -in-charge. 20 excavation in post holes(or similar holes) each in not exc. 0.50 cum getting out returning,filling in an ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm watering and removing surplus soil out of defence land and making good surface all as specified & directed. 21 m&l for pcc(1:3:6) type c2 (40mm graded crushed stone aggregate) filling in post holes, foundation,and other similar work complete all as specified and as directed. 22 s & f hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to fe 410-0 or fe 310-0 23 dismantling fencing wire mesh, any type etc, complete all as specified and as directed. 24 s&f in repair galvanised 2 strand , steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixingto any type of standard railsstraining bolts, including securing ortyping at crossingswith andprovision of galvasnised mild steel wire, staples or steel pins, etc as directed (each line wire to be measured), complete all as specified and as directed. 25 fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire 26 supply only galvanised mild steel chain link fencing, size wire and mesh as approved complete all as specified and directed.note:- the payment for chain link fencing shall be made on the basis of weight of chain link fencing per square metre ascertained by a board of officer convened by ge, by getting minimum 3 samples of each lot . 27 m&l for preparation of new steel surfaces of any description, not otherwise described over 10cm width or girth and applied two coats of synthetic enamel paint over and including a coat of red oxide zinc chrome primer complete all as specified and directed by engr -in-charge. 28 dismantling timber scantlings 40 sq. cm and over in section, in any position in framed section etc., complete all as specified and as directed. 29 dismantling of wrought iron or mild steel work of any description not ohterwise provided for complete all as specified and directed. 30 m&l for ms work in roof trusses (framed), trussed, purlins, crane gantries, rails, posts and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.including special shaped washer etc. complete and including all necessary drilling or cutting holes in brick/ concrete surfaces and making good by pcc and cement plaster, welding work, bolting or reveting/fastening with fastner etc and similar work conforming to fe-290 gde e-165 complete and all as specified 31 s&f ms plain plates, square cut, with riveted, bolted or welded attachment fe-410-w (gde-e-250) quality a as specifed 32 s&f mild steel screw bolts (machine made) with hexabonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n.exc 5cm long, diameter of neck in 5 to 10mm. 33 dismantling asbestos cement (corrugated,semicorrugated, etc.) sheets in roofcoverings including ridges complete all as specified & directed. 34 s & f pre- painted galvalume aluminum zinc coating gi based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. 35 dismantling plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof covering etc. 36 s & f 1mm thic plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters,(joints should be water tight) drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 etc. 37 supply and laid in repairs 110mm bore pvc (swr) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors etc. 38 s& f in repairs pvc (swr) bends for 110mm bore pipe etc. 39 taking up or down 15 mm dia steel tubing & connections or removal to store etc. 40 s & f 15mm bore of tube medium grade galvanized with and including all fittings & fixed complete to walls & ceiling or laid in floors complete all as specified and directed. 41 dismantling water tanks any type of capacityexc 1000 but n.exc 2000 liters 42 dismantling water tanks any type of capacityexc 250 but not exc 500ltr 43 s&f 1000 liter capacity rotational moulded polyethylene water storage tanks (cylin-drical vertical with closed top) tripple layered white, hoisted and fixed in position with and including 20 mm bore ball valves high pressure of ptmt with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and directed. 44 s&f 500 liter capacity rotational moulded polyethylene water storage tanks (cylin-drical vertical with closed top) tripple layered white, hoisted and fixed in position with and including 20 mm bore ball valves high pressure of ptmt with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and directed. 45 s&f in repair 15mm bib taps quarter turn, cast copper alloy , with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed etc. 46 taking down door shutters of any description exc 2sqm complete all as specified. 47 taking down old wooden doors (single/double shutter ) of exc 4sqm n.exc 6sqm any position with complete accessories including chowkhat or frame all as specified and directed by eic. 48 taking down chowkhats or frames or ventilator not exc. 1.5 sq. m each etc. 49 s & f framed work as in doors, gates and ventilators of angle or other sectionfe-410 w (gde e-250) quality a with gusset plates, ms plain black sheet for door, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed. 50 s & f expanded metal, weight not exc 4kg per sqm cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members 51 s & f mild steel flat iron as in hold fast 400mm long embeded in pcc block with splitted ends and in braces in diagonal hand made sliding bolts, clamp hooks and similar worklike banks, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; largehasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to fe410-0 or fe 310-0 52 m & l for pcc (1:2:4)type b1 (20mm graded stone aggregate )asin lintels upto 1..5 m clear span, cills, hold fast for door, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, as directing 53 s&f 35 mm thick 2nd class hardwood, plain, framed, factory made panelled shutters (any number of panels), in with panels of timber flat on both sides (feather edged), of 12 mm bwp commercial ply with commercial veneering on both faces; supplied and fitted to chowkats 54 material and labour for preparation of new wood surfaces of any description not other described over 10cm width or girth and applying twocoats of synthetic enamel paintover and including a coat of pink primer complete all as specified and directed. 55 supply and fixing in repair mild steel butt hinges medium weight, cold rolled, 100mm, isi marked, fixed with stainless steel screws complete all as specified and directed. 56 supply and fixing 150mm aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed. 57 supply and fixing 150 mm size extruded aluminium alloy handels fabricated type, anodised fixed with stainless steel screws complete all as specified and directed. 58 supply and fixing 300mm aluminium alloy, anodised sliding door bolt with hasp staple (bolt type) fixing clips of sheet, cast or extruded setions and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed with stainless steel screws complete all as specified and directed. 59 m&l for providing post construction anti termite treatment to soil under existing floors using chemicalemulsion @ one litre per hole, 300 mm apart along the junction of floor and wall including drilling 12 mm dia holes and plugging with cement sand mortar (1:2) using pigment wherever required, to match the existing floor surfaces complete all as specified and directed.note :-any crack which is developed during execution of att in the floor shall be repaired to match the surface.the cost of this aspect shall deemed to be included in the rates quoted by the contractor 60 m&l for providing post construction anti termite treatment by specified firm along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre i.e. holes @300mm interval including drilling and plugging holes etc in apron/plinth protection and making good the surfaces to match complete all as specified and directed. 61 m&l for providing post construction anti termite treatment by specified firm to voids in masonry using chemical @ one litre per holes at 300 mm intervals by drilling holes at downward angle of 45 degree and replugging them with cement mortar 1:2 to match the existing surface complete all as specified and directed. 62 s&f in repair vitreous china wash down water closet pan pedestal pattern ( type white including pvc seat cover , connection to waste pipe and flushing pipe complete etc. 63 s & f in repair 10 ltr capacity pvc valveless syphonic action type flushing cistern low level white with inlet ball valve and brackets,float and handle, l-bend complete all as specified and directed 64 s&f in repairs vitreous china wash basin, white, flat back, size 580x450mm excluding taps waste, chain and plug and porcelain stopper but including bracket complete all as specified and directed 65 s & fvitreous china urinals, bowl type (back or corner wall type),complete including providing and fixing plugs, bedding urinal against wall in cement mortar1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets,flush pipe, grating and union for discharge pipe.fixed in repairs complete all as specified and directed. 66 s & f urinal spreader of ptmt any colour for fixing with 15 mm dia pipe. (minimum weight 60gms) 67 s & f health faucet (abs body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and abs wall hook including making connections and fixed in position complete in all respect as specified. 68 s & f in repair long body stop valve 15mm bore(quarter turn) fancy type chromium plated screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions. 69 s&f in repairs 15mm bore pvc connection pipe 450mm long with ptmt nuts at both ends etc.

State Government

TRN :49069074 | 15 May, 2025

Tender Value : 3.68 Crore

Madhopur - Rajasthan

Tender for tender for major repair and modernization of existing emrs barnala (raj) - 1 earth work in surface excavation not exceeding 30cm. in depth but exceeding 1.5 meter in width as well as10 sqm on plan including disposal of excavated earth up to 50 mtr. and lift up to 1.5 mtr. disposed soil to be levelled and neatly dressed : all kinds of soil 2 earth work in excavation by mechanical means (hydraulic excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. all kinds of soils 3 supplying and filling in plinth with river sand under floors including watering ramming consolidating and dressing complete including cost of sand 4 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - all work up to plinth level. 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). 5 centering and shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings,strap beam, raft , bases of columns etc. 6 providing and laying in position specified grade ofcement concrete forall rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement.m20 grade nominal mix / design mix providing m-25 grade concrete by usingcement as per codal provision instead ofm-20 grade design mix. 7 random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in:nt mortar 1:6 ( 1-cement : 6-sand). 8 anti termite treatment of floor using imidacloprid 30.5% ec non repellent, odorless, low dose, environmentally safe terniticide with rapid action non corrosive stain free, by drilling 12mm diameter holes 300mm apart injecting the emulsion as per specification and plugging with cement mortar 1:2 ( 1 cement : 2 coarse sand) in the whole floor area dpe 12mm dia termitube system with required number of junction boxes are to be installed. the termitube will run all along the perimeter wall both inside and outside. in the middle area the termitube to be installed at an interval of 1.00 mtr. or less both ways as required with sufficient number of junction boxes to pump the emulsion. after successful testing of termitube, pesticide emulsion of imidacloprid 30.5% ec mixed with water in the ration of 1:474 will be pumped by a motorized spray pump from the junction box in specified manner. the plinth area of the area treated will be measured for payment. 9 centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for : columns, pillars, posts and struts etc. 10 centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for : suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates,anchorblocks,sills,chhajjas,lintel,beam, plinth beam etc. 11 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcementfor walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.m20 grade nominal mix / design mixproviding m-25 grade concrete by usingcement as per codal provision instead ofm-20 grade design mix. 12 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcementfor beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix / design mix 13 providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. (original producers who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to is:1786) thermo-mechanically treated bars (conforming of relevent is code) 14 brick work with f.p.s. bricks of class designation 75 in superstructure above plinth level upto floor v level in all shapes and sizes in : cement mortar 1 : 4 (1 cement : 4 coarse sand) 15 half brick masonry in superstructure , above plinth level upto floor vlevelusing bricks of designation 75cement mortar 1 : 4 (1 cement : 4 coarse sand) 16 carriage of materials:earth,sand ,line morrum,manure or sludge , lead up to 5km 17 filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift. 18 random rubble dry stone kharanja under floor. 19 p & f 1st quality heavy duty vitrified double charged tiles on floor, skirting and steps etc.in different sizes (thickness minimum 10mm) with water absortion less than or equal 0.08% and conforming to is 15622 of approved make in all colour and shade, laid with 20 mm thick cm 1: 4 including grounting the joints with white cement and matching pigment etc complete. size600 mm x 600mm 20 rough chisel dressed sandstone 35 mm thick flooring of approved shade setover 20mm thick base of cement mortar 1:6 (1 cement : 6 coarse sand) and pointingwith cement sand mortar 1:3 with pigment to match the shade of stone with joint thickness up to 15 mm complete in all respects : red sand stone (karauli stone) 21 providing and fixing marble stone flooring table rubbed, 15-18 mm thick over 20mm (av.) thick base of cm 1:4 (1 cement : 4 coarse sand) jointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. slabs bhaislana,abu,kishangarh zebra(black marble) above 3601 cm2 slabs 22 extra for providing edge moulding to 15-18mm thick marble/ granite/kota stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by engineer-in-charge. granite/kota stone work full edge moulding 23 plaster on new surface on walls in cement sand mortar 1:4 including rackingofjointsetc. complete fine finish : 20mm thick . 24 extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 25 6 mm thick cement plaster to ceiling of mix1:3 (1cement : 3-fine sand) 26 providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to is : 13753 & is :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). 27 providing and fixing ist quality mat finished ceremic tile size 300x300mm confirming to is : 13753 coloured tile expect white, grey, ivory, fume red brown in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry including nicely finished joints using water proof joint filler power (untile or roffe make) and finishing with flush pointing in white cement mixed with pigment to match the shade of tile complete (excluding the cost of cement plaster). 28 providing and fixing pressed steel door frames confirming to is 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applyinga coat of approved steel primer after pre-treatment of the surface including filling with cc 1:2:4(m15 grade) complete as directed by engineer-in-charge :profile c 29 providing and fixing external grade board solid core single leaf flush door shutters isi 2202-67 marked using phenol formal dehyderesinin glue both sides with approved steel fittings complete as per annexure a: 35 mm thick commercial veneer both side 30 providing and fixing factory made p.v.c. door frame of size 50x47mm with a wall thickness of5mm, made out of extruded 5mm rigid pvc foam sheet mitred at corners and joined with 2 nos. of 150mm long brackets of 15x15mm m.s. square tube, the vertical door profiles to be reinforced with 19x19mm m.s. square tube of 19 gauge, epdm rubber gasket weather seal to be provided through out the frame. the door frame to be fixed to the wall using m.s. screws of 65/100mm size complete as per manufacturers specification and direction of engineer-in-charge. 31 providing and fixing to existing door frames. 30mm thick factory made solid panel pvc door shutter consisting of frame made out of m.s. tubes of 19 gauge thickness and size of 19mm x 19mm for stiles and 15 mm x15mm , top & bottom rails. m.s .frame shall have a coat of steel primers of approved make and manufacture m.s. frame covered with 5mm thick heat moulded pvc ‘c channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45 degree angle on either side forming stiles; and 5mm thick, 95mm wide pvc sheet out of which 75 mm shall be flat and 20mm shall be tapered in 45 degreeon the inner side to form top and bottom rail and 115mm wide pvc sheet out of which 75 mm shall be flat and 20mm shall be tapered on both sides to form lock rail. top bottom and lock rails shall be provided either side of the panel. 10mm (5mm x 2) thick, 20mm wide cross pvc sheet shall be provided as gap insert for top rail & bottom rail. panelling of 5mm thick pvc sheet to be fitted in the m.s. frame welded/ sealed to the stiles & rails with 7mm (5mm +2mm) thick x 15mm wide pvc sheet bending on inner side, and joined together with solvent cement adhesive. an additional 5mm thick pvc strip of 20mm width is to be stuck on the interior side of the ‘c channel using pvc solvent adhesive etc. complete as per direction of engineer-in-charge, manufacture’s specification & drawing.(for w.c.and bathroom door shutter). 32 providing and fixing of upvc casement openable windows (outward / inward): outer frame made from the extruded upvc windows profile section of size 60w x 60h mm having outer wall thickness of 2.5mm (+/- 0.2mm) and three chamber constuction, white in finish, duly reinforced with 1.5mm thick gi section. all the four corners shall be mitered cut & thermal welded so as to form window frame. frame shall be milled with drain and air equalizer hole in order to be water tight and for drainage of accumulated water, if any, to outer side. fix mullion made of 60w x 80h mm upvc profile section with steel reinforcement shall be provided in windows having 2 or more openable shutters, as per the requirement. frame shall have co-extruded with epdm/tpe-e gasket fitted in in-built groove of frame profile for proper air & sound insulation of the shutter.the shutter of outward openable window shall be made of size 60w x 74h mm and shutter of inward openable window shall be made of size 60w x 77h mm extruded 3 box multi-chamber upvc window profile section of white colour having outer wall thickness of 2.25mm (+/- 0.2mm) provided with reinforcement of 1.5mm thick gi section duly mitered cut & thermal welded at all corners and fitted with upvc glazing bead of size 36 x 20mm with inner and outer co-extruded epdm/tpe-e weather seal gasket alongwith 6mm thick isi make plain float glass. all welding joints of frame and shutter shall be cleaned and milled with the cnc mechainism to provide uniform grooved finish on all visible jaints. hardware: window shutter are fixed with frame on 2.5mmthick ss301 grade friction hinge system to keep the window opened at desired angle. friction hinge also enables easy cleaning of glass on both side from the inside of building. 33 providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete new plastered surface (three or more coats) 34 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding:two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respect. 35 painting exterior surface ofwallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty,etc complete in all respect including scaffolding and safety provisionnew work 36 painting with synthetic enamel paint of approved brand and manufacture togive an even shade :two or more coats on new work 37 french sprit polishing : two or more coats on new work including a coat of wood filler 38 providing and fixing stainless steel railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). grade 304 39 providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide 40 grading roof for water proofing treatment withwater proffing compound cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 41 providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2coarse sand : 4 stone aggregate 10mm and down gauge) includingfinishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : 42 providing & laying broken glazed titles on roof ( broken glazed tilesnot less than 9 kg/sqm) on top of hot bitumen @ 1.7 kg/sqm. (1.40 kg ofvg-40 (30/40 )grade and 0.30 kg/sqm. ofvg-10 (80/100) grade) and joints filled with cement mortar 1 :2 (1 cement:2 marble dust mixed with water proofing compund all complete as per direction of engineer-in-charge. 43 providing and fixing in position collapsible steel shutters with vertical m.s. channels 20 x 10 x 2mm and bracket with flat iron diagonals 20 x 5mm. size with top and bottom rail of t-iron 40 x 40 x 6mm. with 40mm dia steel pulleys/ball bearing complete with bolts, nuts locking arrangements inside and outside stoppers, handles etc. as per specification including applying a priming coat of approved steel primer. (to be measured and paid as per outer dimension). 44 making grooves as per design in plaster 10mm to 20mm wide. 45 making khurras 450 x 450mm with average minimum thickness 50mmcement concrete 1 : 2:4 over p.v.c. sheet 1 mtr. x 1 mtr. x 40micron finished with 12mm cement plaster 1 : 3 and onecoat of neat cement, rounding edges and making and finishing the out let complete. 46 providing and laying damp-proof course with cement concrete grade m-150 (1 : 2 : 4) mortar prepared with 1% solution of water-proof compound complete as per specification . 50mm thick. 47 filling of sunk portion of roof with earthen pots of required height including filling voids with 1:3:6 light concrete, using brick batscomplete levelling and dressing the surface by 50mm thick cement concrete 1:2:4 as per specification. 48 providing and laying water proofing treatment in sunken portion of wcs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (i) first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @0.253 kg//sqm .this layer will be allowed to air cure for 4 hours. (ii) second layer of slurryof cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm this layer will be allowed to air cure for4 hours followed by water curing for 48 hours. the rates includes preparation of surface treatment & sealing of all joints ,corners,junction with polymer mixed slurry. 49 providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with c.p. brass screws and wooden plugs, etc., wherever necessary complete: 20 mm 50 providing and fixingaluminum workfor doors ,windows, ventilators and partition with extruded built up standard tubular / appropriate z sections and other sections of approved make conforming to is :733 and is :1285,fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions , at top ,bottom and sides with required pvc/neoprene felt etc. aluminium section shall be smooth ,rust free, straight ,mitered and jointed mechanically wherever required including cleat angle aluminium snap beading for glazing /paneling , c.p. brass/ stainless steel screws al. tower bolt & al. handle & al. aldrop etc.,all complete as per architectural drawings and thedirections of engineer- in – charge .(glazing and paneling to be paid for separately). for fixed portionpolyester powder coating aluminum( minimum thickness of powder coating 50 micron) 51 providing and fixing 12 mm thick prelaminated three layer medium density (exterior grade ) particle board grade i, type ii conforming to is : 12823 bonded formaldehyde synthetic resin ,of approved brand and manufacture in paneling fixed in aluminium doors ,windows shutters and partition frames with c.p. brass / stainless steel screws etc. complete as per architectural drawings and direction of engineer-in-charge. pre-laminatedparticleboardwithdecorativelaminationononesideandbalancinglaminationonotherside. 52 providing and fixing glazing in aluminium door, window ,ventilator shutters and partitions etc. with pvs / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.(cost of aluminium snap beading shall be paid in basicitem.) with float glass panes of 5.0 mm thickness ( weight not less than 13.50 kg/sqm) 53 providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. 54 providing and fixing sun control film, thickness of film 1 mil visible light transmittance 4-24% & solar energy transmittance 42-51% & total solar energy rejection 37-43%of approved colour and shade , complete in all respect , at all level , as directed by engineer- in -charge. 55 providing and fixing double action hydraulic floor spring of approved brand and manufacture is : 6315 marked, for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece m.s. 56 s&f fixed wire gauge of stainless steel of 14 mesh x 24 gauge to the aluminium window by aluminium beading 20x3mm with suitable screws not exceeding 150mm distance at all heights with all lead and lift with scafolding. 57 p & f indian type white glazed vitreous china 1st quality w.c. orissa pan (is :2556 mark) with 100 mm vitreous china p or s trap including cutting and making good the wall and floor:size 530x410mm. 58 p & f european type white glazed vitreous china 1st quality double syphonic w.c (is :2556 mark) with p or s trap including cutting and making good the wall and floor 59 p & f 15 mm. dia connection pipe of approved quality/make :600 mm dia 60 p & f kitchen & lab. sink of approved make with c.i. brackets duly painted, 40 mm c.p. waste coupling, c.p. brass chain with rubber plug, 40 mm g.i. waste pipe up-to floor level complete including cutting and making good the wall & floor : fire clay glazed kitchen sink (i.s 771-1985marked) size 600 x 450 x 250mm. 61 p & f full-way valve (is:778 mark) or wheel valve of approved make : 62 gun-metal 15mm nominal bore. 63 gun-metal 25mm nominal bore. 64 p & f looking mirrors with p.v.c. frame of approved (atul modi guard saint gobin or equivalent)size 500 x 400 mm 65 p & f towel rail or ring of approved quality/ make: 66 c.p. brass towel rail with brackets 600x 20 mm 67 c.p. brass towel ring revolving type 68 p & f grating of approved quality /makestainless steel sheet size 125 mm diaheavy quality of approved make 69 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes (is 15778 : 2007 code) having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. (concealed work including cutting chases and making good the walls etc.,) 70 15mm dia nominal bore 71 25mm dia nominal bore 72 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes (is 15778 : 2007 code) having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings, this included jointing of pipes & fittings with one step cpvc solvent cement , trenching refilling & testing of joints complete as per direction of engineer in charge.(external work). 73 15mm dia nominal bore 74 25mm dia nominal bore 75 p & f bib cock (is : 8931 mark), superior quality of approved make: c.p. brass bib cock, 15 mm nominal bore 76 p & f stop cock (is :8931 mark), superior quality & of approved make: c.p. brass 15 mm nominal bore. 77 p&f soap dish or tray of approved quality/ make. c.p. brass heavy and superior quality 78 p&f bath shower of approved quality/ make . c.p. brass of heavy & superior quality 150mm. 79 p & f inlet connection (angle valves) superior quality, of approved make, for wash basin, gyser etc. c.p. inlet connection 15 mm brass (is:8931 marked)with 60 cm long thread and nut. 80 p & f ball cock (is :1703 mark) with rod & p.v.c. ball complete : brass wt.400 gm,15mm. 81 p & f pvc storage tank (is : 12701marked indicating the bis license no), of approved make with cover, 25mm dia 1m long g.i. over-flow pipe & 25 cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: 1000 litres capacity. 82 hoisting charges for each floor : 83 construction of manhole in all type of soil inner size 90 x 60 cm. 300 mm thick masonry in cm 1:6, 10 cm. thick cement concrete 1:5:10 in foundation, 20 mm thick inside plaster in cm 1:6, finished with floating neat cement, 50mm thick m-15 grade c.c. flooring, making channels, 80mm thick stone slab covering with 40mm thick m-15 grade c.c. flooring, cement cover with frame of 450mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. lead. depth up to 0.5 m 84 construction of chamber in all type of soil with 300 mm thick masonry in cm 1:6 m,10 cm thick c.c. 1:5:10 in foundation, 20mm thick insider plaster in cm 1:6, finished with floating neat cement, 50mm thick m-15 grade c.c. flooring , earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. size 450 x 450mm depth upto0.5 m cement cover with frame 85 construction of septic tank in all types of soil with 40 cm .thick masonry in cm 1:6, 15 cm thick c.c bed of 1:5:10, m-15 gradec.c floor &rcc slab covering with m15 grade c.c. floor,50 mm thick stone slab partition walls, 20 mm thick plaster in cm 1:6 finished with neat floating cement, 4 nos stone foot rests of approved design ,two no. 450 mm dia each ferro cementcover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr:-size 400 x140x150 cm.(for 50 users)with 115 mm thick rcc (m-20) slab with tor steel reinforcement 10mm ? @15 cm c/c bothways including shuttering complete in all respect 86 construction of open surfacedrain with 112mm thick brick masonry in cm 1:4,110mm thick base concrete 1:5:10, 37mm thick m-15 grade c.c. flooring ,12mm 1:4 cement plaster on all exposed faces of walls including top surface excavation & disposal of earth complete as per approved design/drawing: 150mm drain,225mm av. depth 87 p&f rigid pvc pipe (is:4985 mark) class ii/ (4 kg. /cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant. 88 75mm dia 89 110mm dia 90 160mm dia 91 p&f rigid pvc pipe fittings (is: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: 92 plain tee 110 mm 93 vent covel 75mm 94 plain floor trap 110mm dia 95 bend 87.5 - 75mm 96 bend 87.5 - 110mm 97 pipe clip- 110mm 98 coupler-110 mm dia 99 making connection of g.i. distribution branch with g.i. main including all fitting. beyond 25mm & upto 100mm dia 100 construction of soakage well in all type of soil with 300 mm thick dry masonry, top and bottom 300 mm course in cm 1:6, 80mm thick stone slab, jointing of slab in cm 1 : 3, ralthal, kharanja, 40 mm thick m-15 grade c.c flooring , earthwork complete as per approved drawing including disposal of earth within a lead of 50 mtr.: size 300 cm. dia outside & 300 cm. depth . 101 p & f water closet seat covers with brass hinges complete : solid pvc (is 2548 marked) grade-i black for ewc. 102 p & f low level flushing cistern of 10 litres capacity (is : 2556 mark) of approved make with complete fittings c.i. brackets duly painted, brass ball cock with ball (is: 1703 mark) complete including cutting and making good the wall: pvc withpvcbend and superior internal fittings as per is : 7231 . 103 p & f jet spray for water closet with c.p. copper tube flange of approved make. 104 p & f wvc wash basin (ist quality is:2556 mark) of approved make with c.i. brackets duly painted 1 no. 15 mm c.p. pillar cock (is:8934 mark) & 32 mm c.p. brass waste coupling of approved make, p.v.c waste pipe with pvc nut 32 mm complete including cutting & making good the wall : size 580 mm x 450 mm 105 p & f flush cock/flush valve (is:9758 mark) or wc of approved quality make : c.p. brass push type exposed 25 mm nominal bore. 106 brick work with f.p.s. bricks of class designation 75 in superstructure above plinth level upto floor v level in all shapes and sizes in :cement mortar 1 : 6 (1 cement : 6 coarse sand) 107 random rubble stone masonry with hard stone in superstructure aboveplinth level and upto five levelabove 30cm. thick walls in : 108 repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 m lead with cement mortar 1 :4 ( 1 cement : 4 coarse sand) 109 patch repair to cement concrete floor including digging out old floor in regular shape and removal of rubbish curing etc. complete in all respects. 110 labour charges for repair to door / window without using any material such as applying randha (finishing) tightening of bolts & screw etc. 111 p & f inlet connection (angle valves) superior quality, of approved make, for wash basin, gyser etc. c.p. inlet connection 15mm.brass (is : 8931 marked) 112 p & f 15 mm. dia connection pipe of approved quality/make : cp brass pipe with cp brass nuts upto length 600mm. 113 providing & fixing premium quality white glazed vitreous china sanitary wares (is:2556 mark) of approved make as per direction of engineer-in-charge including cutting and making good the wall and floor. double syphonic european w.c. with mounted w.v.c. flushing cistern of 10 litre capacity complete with all necessary internal fittings with hydraulic seat cover. 114 p & f indian type white glazed vitreous china 1st quality w.c. orissa pan (is :2556 mark) with 100 mm vitreous china p or s trap including cutting and making good the wall and floor: size 580x440mm. 115 providing and fixing t-iron frames for doors, windows and ventilators of mild steel tee-sections, joints mitred and welded with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. 116 providing and fixing fully panelled/partly panelled/double leaf shutter frames for doors as per approved design and drawings with approved ordinary c.p./ oxidised steel fittings as per annexure - a and width of styles & top rails of 100mm and lock rails width of 150mm and bottom rails of 200mm width including teak wood beading of size 19mm x 12mm on both faces complete : 35 mm thick nigeria wood grade i 117 providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth completeold plastered surface (two or more coats) 118 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding:old work (one or more coats ) two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respect.old work (one or more coats ) 119 painting exterior surface ofwallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty,etc complete in all respect including scaffolding and safety provision old work 120 providing & laying broken glazed titles on roof ( broken glazed tilesnot less than 9 kg/sqm) on top of hot bitumen @ 1.7 kg/sqm. (1.40 kg ofvg-40 (30/40 )grade and 0.30 kg/sqm. ofvg-10 (80/100) grade) and joints filled with cement mortar 1 :2 (1 cement:2 marble dust mixed with water proofing compund all complete as per direction of engineer-in-charge. 121 supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance. 122 providing and fixing 1st quality mat finished ceremic tile size 300x300mm confirmingto is : 13755 and is : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4). 123 providing and fixing steel glazed window frame made out of 80x40 mm hollow sheet section of 16 gauge thickness, joint mitred weldedand grinded including hold fast of steel lugs 13mm x 3mm and 15 cm long embedded in c cblock 15 x 10 x 10 cm of 1:3:6 nominal concrete and including fixing of pivoted hinges of superior quality, window shutters made out of 50 x 25.0 mm hollow steel section 15 mm paitam of 18 gauge thickness, joint mitred and grinded including 10mm x 10mm square bars welded to framefor paitam fixing float glass 4mm thickpanes with glazing clips and metal sash putty andfixing of shutters frames peg stay, u shape handle 100 mm long, tower bolts 100 mm long of steel powder coated superior quality including fixing and jointing with frame hinges priming coat with steel primer complete in all respect as per direction of engineer-in –charge window openable. 124 providing and fixing concertina coil fencing with required dia 610 mm (having 15 nos. round per 6 metre length) up to 3m height of wall with existing angle iron y shaped placed 2.4 m or 3.00 m apart and with 9 horizontal r.b.t. stud tied with gi staples and gi clips to retain horizontal including necessary bolts or gi barbed wire tied to angle iron all complete as per direction of engineer in charge with reinforced barbed tape (r.b.t.)/spring core(2.5 mm thick) wire of high tensile strength of 165 kg/sq.mm with tape (0.52 mm thick) and weight 43.478 gm/metre (cost of ms angle, cc block shall be paid extra) 125 renewing glass panes,with putty and nails wherever necessary float glass panes of thickness 4 mm 126 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - all work up to plinth level. m10 grade nominal mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stoneaggregate 40mm nominal size). 127 kota stone slab flooring 25 mm thick over 20 mm (average) thickbase laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing completewith base of cement mortar 1 : 4 (1 cement : 4 coarse sand) for area of each slab from 2001 to 5000 sq.cm 128 earth work in excavation by mechanical means (hydraulic excavator ) / manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5 m, disposed earth to be levelled and neatly dressed : all kinds of soil

Government Departments

TRN :49019871 | 21 May, 2025

Tender Value : 8.47 Lacs

Agra - Uttar Pradesh

Tender for tender for repair work of zone-1 ward no. 16 ratanpura nagla vida community hall. - cleaning of the site for warkable etc. all complete. (non scheduled) 2 1:5:10 (1 cement : 5 coarse sand (zone-iii) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) (dsr 2023 sh-4.1.10 ) 3 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in :cement mortar 1:4 (1 cement : 4 coarse sand) (dsr 2023 sh-6.4.1 ) 4 brick work 7 cm thick with common burnt clay f.p.s. (non modular) brick of class designation 7.5 in cement mortar 1:3 (1 cement : 3 coarse sand) in superstructure above plinth level and upto floor five level. (dsr 2023 sh-6.8 ) 5 reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills,taircases and spiral stair cases above plinth level up to floor fiveevel, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).(dsr 2023 sh-5.3 ) 6 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. thermo-mechanically treated bars of grade fe-500d or more(dsr 2023 sh-5.22.6) 7 centering and shuttering including strutting, propping etc. and removal of form work for :columns, piers, abutments, pillars, posts and struts(dsr 2023 sh-4.3.3 ) 8 12 mm cement plaster of mix : 1:4(1 cement: 4 fine sand)(dsr 2023 sh-13.1.1 ) 9 structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.(dsr 2023 sh-10.1 ) 10 providing and fixing 12 mm thick panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick.fire retardant plywood conforming to is: 5509(dsr 2023 sh-9.126.2 ) 11 providing and fixing isi marked is:1341 m.s. pressed butt hinges bright finished with necessary screws etc. complete :)75x47x1.70 mm (dsr 2023 sh-9.55.3 ) 12 providing & fixing decorative high pressure laminated sheet of plain / wood grain in gloss/ matt/ suede finish with high density protective surface layer and reverse side ofdhesive bonding quality conforming to is : 2046 type s including cost of adhesive of approved quality. 1.0 mm thick (dsr 2023 sh-9.127.2 ) 13 distempering with 1st quality acrylic distemper (ready mixed) having voc content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour new work (two or more coats) over and including water thinnable priming coat with cement primer having voc content less than 50 gram/litre (dsr 2023 sh-13.41.1 ) 14 painting steel work with deluxe multi surface paint to give an even shade. two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture(dsr 2023 sh-1021sub head : 13 finishing13.48.3 ) 15 providing & fixing white vitreous china water closet squatting pan (indian type) along with “s” or “p” trap including dismantling of old wc seat and “s” or “p” trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of engineer-in charge. long pattern w.c pan of size 580x440 mm (dsr 2023 sh-14.80.1) 16 providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require white vitreous china flat back wash basin size 450x 300 mm with single 15mm c.p. brass(dsr 2023 sh-17.7.7) 17 providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white pvc automatic flushing cistern, with fittings, standard size c.p. brass flush pipe, spreaders with unions and clamps (all in c.p. brass) with waste fitting as per is: 2556, c.i. trap with outlet grating and other couplings in c.p. brass, including painting of fittings and cutting and making good the walls and floors wherever required(dsr 2023 sh-17.5.1 ) 18 providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white p.v.c. automatic flushing cistern, with fittings, standard size g.i./ pvc flush pipe for back and front flush with standard spreader pipes with fittings, g.i clamps and c.p. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required: single squatting plate with 5 litre p.v.c. automatic flushing cistern(dsr 2023 sh-17.6.1 ) 19 providing and laying flamed finish granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the engineer-in-charge :flamed finish granite stone slab jet black, cherry red, elite brown, cat eye or equivalent.(dsr 2023 sh-11.55.1 ) 20 providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to isi : 12701, colour of opaque white or as approved by engineer-in- charge. the rate includes making necessary holes for inlet, outlet & over flow pipes. the base support i/c fittings & fixtures for tank shall be paid separately 21 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized pvc medium well casing (cm) pipe of required dia, conforming to is: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of engineer -in-charge100 mm nominal size dia 22 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized pvc medium well casing (cm) pipe of required dia, conforming to is: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of engineer -in-charge150 mm nominal size dia 23 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply and all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one stepcpvc solvent cement and testing of joints complete as per direction of engineer in charge. internal work - exposed on wall 15 mm nominal dia pipes 24 providing and fixing ptmt bib cock of approved quality and colour.15mm nominal bore, 86 mm long, weighing not less than 88 gms 25 providing and fixing ptmt stop cock of approved quality and colour.15 mm nominal bore, 86 mm long, weighing not less than 88 gms) 26 mirror of superior make glass 60x45 cm 27 providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete size of tile 600x600 mm 28 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer-in-charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 29 supply and fixing of light fitting switch board. (none sheduled) 30 supply and fixing wiring of light point. (none sheduled) 31 s/l/j of 20mm dia pvc cunduct pipe etc. all complete. 32 supply & fixing of wiring sub main. 33 supply & fixing of plug point 15mm. 34 lettering & painting of wall etc. all complete. 35 supply & fixing of 27watt. cfl etc. all complete. 36 carriage of materials by manual labour including loading, unloading and stacking for lead less than 01-50 mtrm.207.34+30.42 every 50 additonal meter 37 stone tile work for wall lining upto 10 m height with special adhesive over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement with an admixture of pigment to match the stone shade. 7.38.1 8mm thick (mirror polished and machine cut edge) 7.38.1.1 granite stone of any colour and shade 38 constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast r.c.c. horizontal grating with frame complete as per standard design :with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 39 kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick 40 6 mm cement plaster of mix :1:3 (1 cement : 3 fine sand) 41 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.) 42 stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (to be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) :8.14.1 red sand stone - exposed face fine dressed with rough backingt 43 marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with :raj nagar plain 44 providing and fixing stainless steel ( grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)(dsr 2023 sh-10.28 ) 45 1:2:4 (1 cement : 2 coarse sand (zone-iii) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources). (dsr 2023 s h) 46 supply & fixing granite stone work display board (size 2.50ft x 4.00ft) including painting, lettering etc. all complete. (none schedule) 47 sub total 48 add/deduction rs. for estimate figure amount match 49 grand total

State Government

TRN :49020042 | 13 May, 2025

Tender Value : 0

Kanpur - Uttar Pradesh

Tender for tender for annual repair to rawatpur colony type-iv servant qatar - dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. dsr -15.56 2 12 mm cement plaster of mixwith 1:6 (1 cement: 6 coarse sand) dsr 13.4.2 on wall. 3 12 mm cement plaster of mixwith 1:4 (1 cement: 4 coarse sand) dsr 13.4.1 on celling. 4 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) nondecorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 35 mm thick including isi marked stainless steel butt hinges with necessary screws.dsr-9.21.1 5 providing and fixing bright finished brass tower bolts (barrel type) withnecessary screws etc. complete :200x10 mm dsr9.74.2 6 providing and fixing bright finished brass door latch with necessary screwsetc. complete :300x16x5 mm dsr 9.75.1 7 providing and fixing isi marked oxidised m.s. sliding door bolts with nuts and screws etc. complete : (copper oxidized as per is: 1378) 300x16 mm dsr 9.62.2 8 providing and fixing bright finished brass handles with screws etc.complete: 125 mm dsr 9.81.3 9 providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete dsr 9.82 10 providing and fixing fly proof galvanized m.s. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. with second class teak wood beading 62x19 mm.dsr-9.51.1 11 removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. completedsr - 13.88 12 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.dsr-13.80 13 finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade old work (two or more coats applied @ 1.43 ltr/ 10 sqm) over existing cement paint surface dsr-13.112.1 14 finishing walls with water proofing cement paint of required shade .( old work one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm complete including cost of priming coat. ) dsr-13.109.1 15 distempering with 1st quality acrylic distemper (ready mixed) having voc (volatile organic compound ) content less than 50 gram/ litre, of approved brand and manufacturer including applying additional coats wherever required to achieve even shade and colour .dsr-13.81 16 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : one or more coats on old workdsr-13.99.1 17 providing and laying rectified glazed ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to is : 15622, of approved make, in all colours, shades, except white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding pointing the joints with white cement and matching pigments etc., complete. dsr-11.39 18 providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding grouting the joints with white cement and matching pigments etc., complet size of tile 600x600 mm .dsr-14.41.2 19 providing and laying gang saw cut 18 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20 mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of engineer-in-charge. with granite stone of area less than 0.50 sqm. dsr 16.86.1 20 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. concealed work, including cutting chases and making good the walls etc.15 mm nominal dia pipes . dsr 18.8.1 21 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply and all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. 25 mm nominal dia pipes . dsr 18.8.3 22 providing and fixing c.p. brass bib cock of pproved quality conforming to is:8931 : 15 mm nominal bore sor/dsr 18.49.1 23 providing and fixing c.p. brass long nose bib cock of approved quality conforming to is standards and weighing not less than 810 gms. 15 mm nominal bore sor/dsr 18.50.1 24 providing and fixing c.p. brass angle valve for basin mixer and geyser points of approved quality conforming to is:8931 15 mm nominal bore sor/dsr 18.53.1 25 providing and fixing c.p. brass stop cock (concealed) of standard design and of approved make conforming to is:8931.15 mm nominal bore dsr 18.52.1 26 providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require. white vitreous china wash basin size 630x450 mm with asingle 15 mm c.p. brass pillar tap dsr 17.7.2 27 providing and fixing water closet squatting pan (indian type w.c. pan ) with 100 mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. white vitreous china orissa pattern w.c. pan of size 580x440 mm with integral type foot rests dsr 17.1.2 28 providing and fixing white vitreous china pedestal type water closet (european type w.c. pan) with seat and lid, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever requiredw.c. pan with isi marked white solid plastic seat and lid dsr 17.2.1 29 providing and fixing kitchen sink with c.i. brackets, c.p. brass chain with rubber plug, 40 mm c.p. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required: 17.9.1 white glazed fire clay kitchen sink of size 600x450x 250 mm .dsr -17.9.1 30 providing and fixing t-iron frames for doors, windows and ventilators of mild steel teesections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of c.c. 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).40x40x6mm@3.5kg/m . dsr 10.13.1 31 brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to is: 2222 in superstructure above plinth level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) . with f.p.s.(non modular) bricks .dsr-6.4.2 32 cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate dsr 11.3.1 33 providing and fixing p.v.c. low level flushing cistern with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete.10 litre capacity - white .dsr-17.18.1 34 providing and placing on terrace (at all floor levels) polyethylene water storage tank, is : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. dsr-18.48 35 providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, (i) single socketed pipes.110 mm diameter dsr12.41.2 36 renewing glass panes, with wooden fillets wherever necessary:float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm) dsr14.6.1 37 cleaning of chocked sewer line by diesel running vehicle mountinghydraulic operated high pressure suction cum jetting sewer cleaningmachine fitted with pump having 4000 litres suction capacity and 6000 litres water jetting tank capacity including skilled operator, supervising engineer etc. for cleaning and partial desilting of manholes and dechocking of sewer lines. dechocking and flushing of sewer line from one manhole to another by high pressure jetting system of 2200 psi for sewer line from 150 mm dia upto 300 mm dsr 14.77 38 reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) dsr 5.2.2 39 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. thermo-mechanically treated bars of grade fe-500d or more.dsr 5.22a.6 40 centering and shuttering including strutting, propping etc. and removal of form work for : columns, piers, abutments, pillars, posts and struts.dsr 4.3.3

State Government

TRN :49020061 | 13 May, 2025

Tender Value : 0

Kanpur - Uttar Pradesh

Tender for tender for annual repair to mc robertganj colony - dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. dsr -15.56 2 12 mm cement plaster of mixwith 1:6 (1 cement: 6 coarse sand) dsr 13.4.2 on wall. 3 12 mm cement plaster of mixwith 1:4 (1 cement: 4 coarse sand) dsr 13.4.1 on celling. 4 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) nondecorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 35 mm thick including isi marked stainless steel butt hinges with necessary screws.dsr-9.21.1 5 providing and fixing bright finished brass tower bolts (barrel type) withnecessary screws etc. complete :200x10 mm dsr9.74.2 6 providing and fixing bright finished brass door latch with necessary screwsetc. complete :300x16x5 mm dsr 9.75.1 7 providing and fixing isi marked oxidised m.s. sliding door bolts with nuts and screws etc. complete : (copper oxidized as per is: 1378) 300x16 mm dsr 9.62.2 8 providing and fixing bright finished brass handles with screws etc.complete: 125 mm dsr 9.81.3 9 providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete dsr 9.82 10 providing and fixing fly proof galvanized m.s. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. with second class teak wood beading 62x19 mm.dsr-9.51.1 11 removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. completedsr - 13.88 12 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.dsr-13.80 13 finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade old work (two or more coats applied @ 1.43 ltr/ 10 sqm) over existing cement paint surface dsr-13.112.1 14 finishing walls with water proofing cement paint of required shade .( old work one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm complete including cost of priming coat. ) dsr-13.109.1 15 distempering with 1st quality acrylic distemper (ready mixed) having voc (volatile organic compound ) content less than 50 gram/ litre, of approved brand and manufacturer including applying additional coats wherever required to achieve even shade and colour .dsr-13.81 16 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : one or more coats on old work dsr-13.99.1 17 providing and laying rectified glazed ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to is : 15622, of approved make, in all colours, shades, except white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding pointing the joints with white cement and matching pigments etc., complete. dsr-11.39 18 providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding grouting the joints with white cement and matching pigments etc., complet size of tile 600x600 mm .dsr-14.41.2 19 providing and laying gang saw cut 18 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20 mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of engineer-in-charge. with granite stone of area less than 0.50 sqm. dsr 16.86.1 20 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. concealed work, including cutting chases and making good the walls etc.15 mm nominal dia pipes . dsr 18.8.1 21 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply and all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. 25 mm nominal dia pipes . dsr 18.8.3 22 providing and fixing c.p. brass bib cock of pproved quality conforming to is:8931 : 15 mm nominal bore sor/dsr 18.49.1 23 providing and fixing c.p. brass long nose bib cock of approved quality conforming to is standards and weighing not less than 810 gms. 15 mm nominal bore sor/dsr 18.50.1 24 providing and fixing c.p. brass angle valve for basin mixer and geyser points of approved quality conforming to is:8931 15 mm nominal bore sor/dsr 18.53.1 25 providing and fixing c.p. brass stop cock (concealed) of standard design and of approved make conforming to is:8931.15 mm nominal bore dsr 18.52.1 26 providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require. white vitreous china wash basin size 630x450 mm with asingle 15 mm c.p. brass pillar tap dsr 17.7.2 27 providing and fixing water closet squatting pan (indian type w.c. pan ) with 100 mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. white vitreous china orissa pattern w.c. pan of size 580x440 mm with integral type foot rests dsr 17.1.2 28 providing and fixing white vitreous china pedestal type water closet (european type w.c. pan) with seat and lid, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever requiredw.c. pan with isi marked white solid plastic seat and lid dsr 17.2.1 29 providing and fixing kitchen sink with c.i. brackets, c.p. brass chain with rubber plug, 40 mm c.p. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required: 17.9.1 white glazed fire clay kitchen sink of size 600x450x 250 mm .dsr -17.9.1 30 providing and fixing t-iron frames for doors, windows and ventilators of mild steel teesections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of c.c. 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).40x40x6mm@3.5kg/m . dsr 10.13.1 31 brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to is: 2222 in superstructure above plinth level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) . with f.p.s.(non modular) bricks .dsr-6.4.2 32 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in foundation and plinth in:: cement mortar 1:6 (1 cement : 6 coarse sand)dsr 6.1.2 33 cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate dsr 11.3.1 34 providing and fixing p.v.c. low level flushing cistern with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete.10 litre capacity - white .dsr-17.18.1 35 providing and placing on terrace (at all floor levels) polyethylene water storage tank, is : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. dsr-18.48 36 earth work in excavation by mechanical means (hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by engineer-in-charge. all kinds of soil dsr 2.6.1 37 1:4:8 (1 cement : 4 coarse sand (zone-iii) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources). dsr 4.1.8 38 providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, (i) single socketed pipes.110 mm diameter dsr12.41.2 39 renewing glass panes, with wooden fillets wherever necessary:float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm) dsr14.6.1 40 cleaning of chocked sewer line by diesel running vehicle mounting hydraulic operated high pressure suction cum jetting sewer cleaning machine fitted with pump having 4000 litres suction capacity and 6000 litres water jetting tank capacity including skilled operator, supervising engineer etc. for cleaning and partial desilting of manholes and dechocking of sewer lines. dechocking and flushing of sewer line from one manhole to another by high pressure jetting system of 2200 psi for sewer line from 150 mm dia upto 300 mm dsr 14.77 41 reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) dsr 5.2.2 42 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. thermo-mechanically treated bars of grade fe-500d or more.dsr 5.22a.6 43 centering and shuttering including strutting, propping etc. and removal of form work for : columns, piers, abutments, pillars, posts and struts.dsr 4.3.3

Related Searched Keywords : waste removal

List of waste-removal Tenders

Tender for removal of legacy waste through bioremediation and bio-mining process to reclaim the existing dump yard situated in khonsa city on design, building, finance, own and operate model

Get waste removal Tender Alert...

Related Searched Keywords : waste removal

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us