Filters

List of u-bend Tenders

List of latest u-bend Tenders in Indian Tenders. Click on any u-bend Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for u-bend Tenders.

All-Tenders (169)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

State Government

TRN :49059552 | 23 May, 2025

Tender Value : 0

Kolkata - West Bengal

Tender for supply, delivery & installation of submersible pumping machinery and other electrical / mechanical equipment etc. including allied works for kaknan water supply scheme, t.w. no. iv, block: khanakul-ii, district - hooghly under electrical division, phe dte.- 1 part-a supply and delivery at site submersible pumping machinery directly coupled with wet winding type submersible motor having the following specification pump.duty condition :36 cu.mtrhead :58 mtr.motor : submersible type 3 ph. 50 hz. 400v + 10%, mos:- star deltaimpeller : gm/ ss/ cromesteelmotor winding : wet type.pump outlet - 65/75/100 mm.(test certificate, warranty certificate along with characteristic curve should be submitted at the time of delivery.) 2 supply and delivery at site the following:-upvc 80 mm dia column pipewith both side square threaded (8 tpi)with one socket and o ring biax technology with wiring lock system non corrosive,high tensile having iso 9001 standard. 3 i)3 mtr. long. 4 ii) 1.5 mtr. long 5 iii) 80 mm dia top & bottom adaptor 6 100 mm x 80 mm dia gi reducer 7 supply and delivery at site heavy type suitable dia m.s. suspension clamp for above column pipe along with nuts, bolts and washers etc. 8 supply and delivery at site 80 mm. dia cidf sluice valve- 1 no., 80mm non return valve (swing type - 1 no.) pn - 1.0,80mm ms heavy flange - 1 no., cidf bend 90o - 1 no., cidf / ms (heavy) short piece as required length, 80mm cidf tee - 1 no., reducer, nut bolt and other ci / ms specials etc. as required as per i.s. specification and other required materials for the job i.e. for making complete construction of delivery and wash out lineas per relavant i.s. (test certificate for valve should be submitted at the time of delivery). 9 supply and delivery at site split type m.s. fabricated suitable tubewell cover for the tubewell housing with necessary clamping arrangement including holes for column pipe, air pipe and cable entry etc. 10 supply and delivery at site depth gauge (make : h. guru) 102 mm dia. with steel airbreak pipe required length with all other fittings and accessories for the work including supplying on the good quality hand pump of approve make 11 supply and delivery at site pressure gauge 102 mm. dia and 7 kg. /cm2 range, brass cocks and fitting complete(h.guru) 12 supply and delivery at site 4 sq. mm. 3 core copper 1.1 kv grade pvc insulated water proof flat submersible cable. 13 making safety device for above pump by supplying 3 nos. suitable size ms clamp/ ms cage and 1 dia nylon rope of required length including supplying nuts, bolts, and other materials as per direction. 14 supply & delivery of double flanged three phase 50 hz quarter turn electrical actuator [gear case lubrication : sp68 is:13095, torch switches: 2 x 1 no / 1 nc changeover contact, positional limit switches: 2 x 1 no / 1 nc changeover contacts] operated flange type butterfly valve (pn - 1.0) 80 mm. dia with mechanical position indicator, ci body & disk - is: 210 gr. fg 260, shaft of stainless steel aisi 410 as per bs 5155 ip - 68 / s-2,(test certificate should be submitted at the time of delivery) 15 supply & delivery of 415 v mcc cum pdb. with minimum 2mm thickness and degree of protection ip - 54, conforming to is-8623 withsuitable bus bar, digital voltmeter ammeter, contactor, delay timer, mcb, valve actuator starter etc. with plc logic & ups as detailed in annexure - i7.5 -12.5 hp with sds (star delta starter)panel make : digitek / rnr industries /pce projects / opg power system / ecs.[tc / gc to be submitted along with panel after approval of detail power and control circuit drawing by eic]. 16 supply & delivery of 35 sq. mm. 3 1/2 core pvc insulatedal. armoured cable (1.1 kv grade), is 1554 (part - i) / is 7098 (part-i) make : incab /gloster / nicco / polycab / crystal. 17 supply & delivery of 100 amp. 440 v, 50 hz. tpn main switch with rewireable type fuse link 18 supply & delivery of 100 amp. industrial copper busbar 19 supply & delivery of 4 pole 100 amp changeover unit 20 supply & delivery of 100 amp 4 pole mccb with adjustable overload and adjacent short circuit protection including enclosures. 21 supply & delivery at site of 25 kva, 3 phase oil cooled type servo motor operated wound line voltage corrector conforming to is-9815 [pt-i] 1994 suitable for unbalanced input voltage.input voltage: 3 phase main supply phase to phase 200v-500v 3 servo motor in 3 phase with all protection by mcb (make- abb / siemens/ l&t)output voltage: 3 phase balanced output phase to phase 415v + 1% (test certificate & warranty certificate should be submitted at the time of delivery) 22 supply and delivery of automatic plunger type chlorinator for feeding accurately automatic controlled dosage of chlorine solution into the water by connecting metering pump with flow rate of water 0-100 ltr/hr. with maximum pressure of 10 kg./cm2 suitable dosing pump and other necessary accessories on the delivery pipe line as required. the pump shall be coupled with 1/2 hp motor having 3 phase power and 1440 rpm (+4%).(test certificate will be submitted at the time of delivery) 23 part-binstallation of pumping machinery with valves, pipe & pipe specials, sort piece, presurre gauge including hoisting of column pipe making all electrical and water line interconnection complete as per direction including supply of necessary materials as required for the work. 24 making of tubewell foundation (size- 3x 3x 3.5 approx) as per site situation including supply of necessary materials as bricks, sand, cement, stone chips etc. with plastering & neat cement finishing to complete as per direction. 25 installtion of panel & actuator operated ci butterfly valvewith supply of 12 core 2.5 sq. mm. copper control cable, compensating ms flange, nuts, bolts gasket and other fixing materials as required to complete the job including necessary making of brick pillar as per site situation with supply of necessary materials like bricks, sand, cement, stone chips etc. with plastering & neat cement finishing in all respect including successfull operation along with testing of the whole installation as per entire satisfaction of eic. 26 installation with testing and commissioning of the voltage stabilizer with necessary foundation along with necessary accessories in the suitable position and drawing cable with ms shaddle, making all electrical connection including socketing, crimping to complete the work as per direction. 27 installation of above supplied chlorinator pump set and drawing of power line by supplying of necessary wire and continuous earthing connected to auto/ manual panel. this includes the cost of making necessary brick foundation base with neat cement finish by supplying all requered materials and testing entire set as per direction of eic 28 making internal electrification with 16amp main switch/mcb (make: havells/ any approved) by 1.5 sq.mm frlsh grade copper pvc insulated single core multistrand wire (make: havells/ mescab/ finolex/ any approved) in pvc casing of pump house consisting of 2 nos. bracket point, 1 no. tube light point, 1 no. bulk head point and 1 no. five pin 5 amp. socket point, 1 no. ceiling fan point with controlling switches including supply of 2 nos. bracket with 12w led lamp, 1 no. 20 watt led tube light set, 1 no. outdoor type bulk head with 9w led lamp and drawing of necessary earthing (1.0 sq.mm) material all complete as per direction eic. (led light make: philips/ havells/ any approved) 29 supply and fitting fixing of 45 watt. x 2 nos. led light set [make - philips, model: brp031 led45 cw slr gr psu] with 2 nos 40 mm dia 1.5 mtr. long g.i pipe bracket fixed on the roof of the pump house with properly grout including making power connection by 2 x 1.5 sq. mm copper fr grade flexible wire through pvc casing/conduit with drawing earth conductor (1.0 sq mm copper flexible wire), fitting fixing of 15 amp switch on board with all complete as per direction of eic. 30 earthing confirming to is: 3043 by 50mm dia gi pipe 3.64mm thick x 3.04m long and 1 x 4 swggi (hot dip) wire (4 mts. long), 13mm dia x 80mm long gi bolts, double nuts, double washers including supply & fixing of 15mm dia gi pipe protection (1 mtr long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 mtrs below the ground level and restoring surface duly rammed as below. a) for soft soilby tata - medium gi pipe 31 drawing earth by m.s. flat strip (20mm x 3mm) fromearth bus / electrode to above differentcomponents as per i.e. rules and as per direction of eic. 32 supply & fitting fixing of 100 amp. kit kat (3 nos.)(make : havells) with required size wooden board mounted on wall. 33 supply, delivery & fitting fixing of 48 sweep 230 volt, 50 hz, ac ceiling fan (make : havells/ cg/ approved make) including fitting fixing on ceiling and making electrical connection complete. 34 supply & delivery at site 2 nos. plastic chair & 1 no. plastic table (make: cello / supreme / nilkamal) 35 trial operation and guarding of whole installationas per departmental requirement and guideline 1 no. operator @ 465/- per day with 8.33% bonus. [as per existing departmental terms & conditions] 36 add: 18% gst 37 add: 1% cess

State Government

TRN :49059555 | 23 May, 2025

Tender Value : 0

Kolkata - West Bengal

Tender for supply, delivery & installation of submersible pumping machinery and other electrical / mechanical equipment etc. including allied works for refaitpur water supply scheme, zone-i, t.w. no. iii, block: chinsurah mogra, district - hooghly under electrical division, phe dte- 1 part-a supply and delivery at site submersible pumping machinery directly coupled with wet winding type submersible motor having the following specification pump.duty condition :36 cu.mtrhead :58 mtr.motor : submersible type 3 ph. 50 hz. 400v + 10%, mos:- star deltaimpeller : gm/ ss/ cromesteelmotor winding : wet type.pump outlet - 65/75/100 mm.(test certificate, warranty certificate along with characteristic curve should be submitted at the time of delivery.) 2 supply and delivery at site the following:-upvc 80 mm dia column pipewith both side square threaded (8 tpi)with one socket and o ring biax technology with wiring lock system non corrosive,high tensile having iso 9001 standard. 3 i)3 mtr. long. 4 ii) 1.5 mtr. long 5 iii) 80 mm dia top & bottom adaptor 6 100 mm x 80 mm dia gi reducer 7 supply and delivery at site heavy type suitable dia m.s. suspension clamp for above column pipe along with nuts, bolts and washers etc. 8 supply and delivery at site 80 mm. dia cidf sluice valve- 1 no., 80mm non return valve (swing type - 1 no.) pn - 1.0,80mm ms heavy flange - 1 no., cidf bend 90o - 1 no., cidf / ms (heavy) short piece as required length, 80mm cidf tee - 1 no., reducer, nut bolt and other ci / ms specials etc. as required as per i.s. specification and other required materials for the job i.e. for making complete construction of delivery and wash out lineas per relavant i.s. (test certificate for valve should be submitted at the time of delivery). 9 supply and delivery at site split type m.s. fabricated suitable tubewell cover for the tubewell housing with necessary clamping arrangement including holes for column pipe, air pipe and cable entry etc. 10 supply and delivery at site depth gauge (make : h. guru) 102 mm dia. with steel airbreak pipe required length with all other fittings and accessories for the work including supplying on the good quality hand pump of approve make 11 supply and delivery at site pressure gauge 102 mm. dia and 7 kg. /cm2 range, brass cocks and fitting complete(h.guru) 12 supply and delivery at site 4 sq. mm. 3 core copper 1.1 kv grade pvc insulated water proof flat submersible cable. 13 making safety device for above pump by supplying 3 nos. suitable size ms clamp/ ms cage and 1 dia nylon rope of required length including supplying nuts, bolts, and other materials as per direction. 14 supply & delivery of double flanged three phase 50 hz quarter turn electrical actuator [gear case lubrication : sp68 is:13095, torch switches: 2 x 1 no / 1 nc changeover contact, positional limit switches: 2 x 1 no / 1 nc changeover contacts] operated flange type butterfly valve (pn - 1.0) 80 mm. dia with mechanical position indicator, ci body & disk - is: 210 gr. fg 260, shaft of stainless steel aisi 410 as per bs 5155 ip - 68 / s-2,(test certificate should be submitted at the time of delivery) 15 supply & delivery of 415 v mcc cum pdb. with minimum 2mm thickness and degree of protection ip - 54, conforming to is-8623 withsuitable bus bar, digital voltmeter ammeter, contactor, delay timer, mcb, valve actuator starter etc. with plc logic & ups as detailed in annexure - i7.5 -12.5 hp with sds (star delta starter)panel make : digitek / rnr industries /pce projects / opg power system / ecs.[tc / gc to be submitted along with panel after approval of detail power and control circuit drawing by eic]. 16 supply & delivery of 35 sq. mm. 3 1/2 core pvc insulatedal. armoured cable (1.1 kv grade), is 1554 (part - i) / is 7098 (part-i) make : incab /gloster / nicco / polycab / crystal. 17 supply & delivery of 100 amp. 440 v, 50 hz. tpn main switch with rewireable type fuse link 18 supply & delivery of 100 amp. industrial copper busbar 19 supply & delivery of 4 pole 100 amp changeover unit 20 supply & delivery of 100 amp 4 pole mccb with adjustable overload and adjacent short circuit protection including enclosures. 21 supply & delivery at site of 25 kva, 3 phase oil cooled type servo motor operated wound line voltage corrector conforming to is-9815 [pt-i] 1994 suitable for unbalanced input voltage.input voltage: 3 phase main supply phase to phase 200v-500v 3 servo motor in 3 phase with all protection by mcb (make- abb / siemens/ l&t)output voltage: 3 phase balanced output phase to phase 415v + 1% (test certificate & warranty certificate should be submitted at the time of delivery) 22 supply and delivery of automatic plunger type chlorinator for feeding accurately automatic controlled dosage of chlorine solution into the water by connecting metering pump with flow rate of water 0-100 ltr/hr. with maximum pressure of 10 kg./cm2 suitable dosing pump and other necessary accessories on the delivery pipe line as required. the pump shall be coupled with 1/2 hp motor having 3 phase power and 1440 rpm (+4%).(test certificate will be submitted at the time of delivery) 23 part-binstallation of pumping machinery with valves, pipe & pipe specials, sort piece, presurre gauge including hoisting of column pipe making all electrical and water line interconnection complete as per direction including supply of necessary materials as required for the work. 24 making of tubewell foundation (size- 3x 3x 3.5 approx) as per site situation including supply of necessary materials as bricks, sand, cement, stone chips etc. with plastering & neat cement finishing to complete as per direction. 25 installtion of panel & actuator operated ci butterfly valvewith supply of 12 core 2.5 sq. mm. copper control cable, compensating ms flange, nuts, bolts gasket and other fixing materials as required to complete the job including necessary making of brick pillar as per site situation with supply of necessary materials like bricks, sand, cement, stone chips etc. with plastering & neat cement finishing in all respect including successfull operation along with testing of the whole installation as per entire satisfaction of eic. 26 installation with testing and commissioning of the voltage stabilizer with necessary foundation along with necessary accessories in the suitable position and drawing cable with ms shaddle, making all electrical connection including socketing, crimping to complete the work as per direction. 27 installation of above supplied chlorinator pump set and drawing of power line by supplying of necessary wire and continuous earthing connected to auto/ manual panel. this includes the cost of making necessary brick foundation base with neat cement finish by supplying all requered materials and testing entire set as per direction of eic 28 making internal electrification with 16amp main switch/mcb (make: havells/ any approved) by 1.5 sq.mm frlsh grade copper pvc insulated single core multistrand wire (make: havells/ mescab/ finolex/ any approved) in pvc casing of pump house consisting of 2 nos. bracket point, 1 no. tube light point, 1 no. bulk head point and 1 no. five pin 5 amp. socket point, 1 no. ceiling fan point with controlling switches including supply of 2 nos. bracket with 12w led lamp, 1 no. 20 watt led tube light set, 1 no. outdoor type bulk head with 9w led lamp and drawing of necessary earthing (1.0 sq.mm) material all complete as per direction eic. (led light make: philips/ havells/ any approved) 29 supply and fitting fixing of 45 watt. x 2 nos. led light set [make - philips, model: brp031 led45 cw slr gr psu] with 2 nos 40 mm dia 1.5 mtr. long g.i pipe bracket fixed on the roof of the pump house with properly grout including making power connection by 2 x 1.5 sq. mm copper fr grade flexible wire through pvc casing/conduit with drawing earth conductor (1.0 sq mm copper flexible wire), fitting fixing of 15 amp switch on board with all complete as per direction of eic. 30 earthing confirming to is: 3043 by 50mm dia gi pipe 3.64mm thick x 3.04m long and 1 x 4 swggi (hot dip) wire (4 mts. long), 13mm dia x 80mm long gi bolts, double nuts, double washers including supply & fixing of 15mm dia gi pipe protection (1 mtr long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 mtrs below the ground level and restoring surface duly rammed as below. a) for soft soilby tata - medium gi pipe 31 drawing earth by m.s. flat strip (20mm x 3mm) fromearth bus / electrode to above differentcomponents as per i.e. rules and as per direction of eic. 32 supply & fitting fixing of 100 amp. kit kat (3 nos.)(make : havells) with required size wooden board mounted on wall. 33 supply, delivery & fitting fixing of 48 sweep 230 volt, 50 hz, ac ceiling fan (make : havells/ cg/ approved make) including fitting fixing on ceiling and making electrical connection complete. 34 supply & delivery at site 2 nos. plastic chair & 1 no. plastic table (make: cello / supreme / nilkamal) 35 trial operation and guarding of whole installationas per departmental requirement and guideline 1 no. operator @ 465/- per day with 8.33% bonus. [as per existing departmental terms & conditions] 36 add: 18% gst 37 add: 1% cess

State Government

TRN :49059565 | 23 May, 2025

Tender Value : 0

Kolkata - West Bengal

Tender for supply, delivery & installation of submersible pumping machinery and other electrical / mechanical equipment etc. including allied works for raghubati water supply scheme, t.w. no. iii & iv, block: goghat-i, district - hooghly under electrical division, phe dte.- 1 part-a supply and delivery at site submersible pumping machinery directly coupled with wet winding type submersible motor having the following specification pump.duty condition :36 cu.mtrhead :58 mtr.motor : submersible type 3 ph. 50 hz. 400v + 10%, mos:- star deltaimpeller : gm/ ss/ cromesteelmotor winding : wet type.pump outlet - 65/75/100 mm.(test certificate, warranty certificate along with characteristic curve should be submitted at the time of delivery.) 2 supply and delivery at site the following:-upvc 80 mm dia column pipewith both side square threaded (8 tpi)with one socket and o ring biax technology with wiring lock system non corrosive,high tensile having iso 9001 standard. 3 i)3 mtr. long. 4 ii) 1.5 mtr. long 5 iii) 80 mm dia top & bottom adaptor 6 100 mm x 80 mm dia gi reducer 7 supply and delivery at site heavy type suitable dia m.s. suspension clamp for above column pipe along with nuts, bolts and washers etc. 8 supply and delivery at site 80 mm. dia cidf sluice valve- 1 no., 80mm non return valve (swing type - 1 no.) pn - 1.0,80mm ms heavy flange - 1 no., cidf bend 90o - 1 no., cidf / ms (heavy) short piece as required length, 80mm cidf tee - 1 no., reducer, nut bolt and other ci / ms specials etc. as required as per i.s. specification and other required materials for the job i.e. for making complete construction of delivery and wash out lineas per relavant i.s. (test certificate for valve should be submitted at the time of delivery). 9 supply and delivery at site split type m.s. fabricated suitable tubewell cover for the tubewell housing with necessary clamping arrangement including holes for column pipe, air pipe and cable entry etc. 10 supply and delivery at site depth gauge (make : h. guru) 102 mm dia. with steel airbreak pipe required length with all other fittings and accessories for the work including supplying on the good quality hand pump of approve make 11 supply and delivery at site pressure gauge 102 mm. dia and 7 kg. /cm2 range, brass cocks and fitting complete(h.guru) 12 supply and delivery at site 4 sq. mm. 3 core copper 1.1 kv grade pvc insulated water proof flat submersible cable. 13 making safety device for above pump by supplying 3 nos. suitable size ms clamp/ ms cage and 1 dia nylon rope of required length including supplying nuts, bolts, and other materials as per direction. 14 supply & delivery of double flanged three phase 50 hz quarter turn electrical actuator [gear case lubrication : sp68 is:13095, torch switches: 2 x 1 no / 1 nc changeover contact, positional limit switches: 2 x 1 no / 1 nc changeover contacts] operated flange type butterfly valve (pn - 1.0) 80 mm. dia with mechanical position indicator, ci body & disk - is: 210 gr. fg 260, shaft of stainless steel aisi 410 as per bs 5155 ip - 68 / s-2,(test certificate should be submitted at the time of delivery) 15 supply & delivery of 415 v mcc cum pdb. with minimum 2mm thickness and degree of protection ip - 54, conforming to is-8623 withsuitable bus bar, digital voltmeter ammeter, contactor, delay timer, mcb, valve actuator starter etc. with plc logic & ups as detailed in annexure - i7.5 -12.5 hp with sds (star delta starter)panel make : digitek / rnr industries /pce projects / opg power system / ecs.[tc / gc to be submitted along with panel after approval of detail power and control circuit drawing by eic]. 16 supply & delivery of 35 sq. mm. 3 1/2 core pvc insulatedal. armoured cable (1.1 kv grade), is 1554 (part - i) / is 7098 (part-i) make : incab /gloster / nicco / polycab / crystal. 17 supply & delivery of 100 amp. 440 v, 50 hz. tpn main switch with rewireable type fuse link 18 supply & delivery of 100 amp. industrial copper busbar 19 supply & delivery of 4 pole 100 amp changeover unit 20 supply & delivery of 100 amp 4 pole mccb with adjustable overload and adjacent short circuit protection including enclosures. 21 supply & delivery at site of 25 kva, 3 phase oil cooled type servo motor operated wound line voltage corrector conforming to is-9815 [pt-i] 1994 suitable for unbalanced input voltage.input voltage: 3 phase main supply phase to phase 200v-500v 3 servo motor in 3 phase with all protection by mcb (make- abb / siemens/ l&t)output voltage: 3 phase balanced output phase to phase 415v + 1% (test certificate & warranty certificate should be submitted at the time of delivery) 22 supply and delivery of automatic plunger type chlorinator for feeding accurately automatic controlled dosage of chlorine solution into the water by connecting metering pump with flow rate of water 0-100 ltr/hr. with maximum pressure of 10 kg./cm2 suitable dosing pump and other necessary accessories on the delivery pipe line as required. the pump shall be coupled with 1/2 hp motor having 3 phase power and 1440 rpm (+4%).(test certificate will be submitted at the time of delivery) 23 part-binstallation of pumping machinery with valves, pipe & pipe specials, sort piece, presurre gauge including hoisting of column pipe making all electrical and water line interconnection complete as per direction including supply of necessary materials as required for the work. 24 making of tubewell foundation (size- 3x 3x 3.5 approx) as per site situation including supply of necessary materials as bricks, sand, cement, stone chips etc. with plastering & neat cement finishing to complete as per direction. 25 installtion of panel & actuator operated ci butterfly valvewith supply of 12 core 2.5 sq. mm. copper control cable, compensating ms flange, nuts, bolts gasket and other fixing materials as required to complete the job including necessary making of brick pillar as per site situation with supply of necessary materials like bricks, sand, cement, stone chips etc. with plastering & neat cement finishing in all respect including successfull operation along with testing of the whole installation as per entire satisfaction of eic. 26 installation with testing and commissioning of the voltage stabilizer with necessary foundation along with necessary accessories in the suitable position and drawing cable with ms shaddle, making all electrical connection including socketing, crimping to complete the work as per direction. 27 installation of above supplied chlorinator pump set and drawing of power line by supplying of necessary wire and continuous earthing connected to auto/ manual panel. this includes the cost of making necessary brick foundation base with neat cement finish by supplying all requered materials and testing entire set as per direction of eic 28 making internal electrification with 16amp main switch/mcb (make: havells/ any approved) by 1.5 sq.mm frlsh grade copper pvc insulated single core multistrand wire (make: havells/ mescab/ finolex/ any approved) in pvc casing of pump house consisting of 2 nos. bracket point, 1 no. tube light point, 1 no. bulk head point and 1 no. five pin 5 amp. socket point, 1 no. ceiling fan point with controlling switches including supply of 2 nos. bracket with 12w led lamp, 1 no. 20 watt led tube light set, 1 no. outdoor type bulk head with 9w led lamp and drawing of necessary earthing (1.0 sq.mm) material all complete as per direction eic. (led light make: philips/ havells/ any approved) 29 supply and fitting fixing of 45 watt. x 2 nos. led light set [make - philips, model: brp031 led45 cw slr gr psu] with 2 nos 40 mm dia 1.5 mtr. long g.i pipe bracket fixed on the roof of the pump house with properly grout including making power connection by 2 x 1.5 sq. mm copper fr grade flexible wire through pvc casing/conduit with drawing earth conductor (1.0 sq mm copper flexible wire), fitting fixing of 15 amp switch on board with all complete as per direction of eic. 30 earthing confirming to is: 3043 by 50mm dia gi pipe 3.64mm thick x 3.04m long and 1 x 4 swggi (hot dip) wire (4 mts. long), 13mm dia x 80mm long gi bolts, double nuts, double washers including supply & fixing of 15mm dia gi pipe protection (1 mtr long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 mtrs below the ground level and restoring surface duly rammed as below. a) for soft soilby tata - medium gi pipe 31 drawing earth by m.s. flat strip (20mm x 3mm) fromearth bus / electrode to above differentcomponents as per i.e. rules and as per direction of eic. 32 supply & fitting fixing of 100 amp. kit kat (3 nos.)(make : havells) with required size wooden board mounted on wall. 33 supply, delivery & fitting fixing of 48 sweep 230 volt, 50 hz, ac ceiling fan (make : havells/ cg/ approved make) including fitting fixing on ceiling and making electrical connection complete. 34 supply & delivery at site 2 nos. plastic chair & 1 no. plastic table (make: cello / supreme / nilkamal) 35 trial operation and guarding of whole installationas per departmental requirement and guideline 1 no. operator @ 465/- per day with 8.33% bonus. [as per existing departmental terms & conditions] 36 for t.w. no. iii 37 for t.w. no. iv 38 add: 18% gst 39 add: 1% cess

State Government

TRN :49059624 | 23 May, 2025

Tender Value : 0

Kolkata - West Bengal

Tender for supply, delivery & installation of submersible pumping machinery and other electrical / mechanical equipment etc. including allied works for jagatpur water supply scheme, t.w. no. vi, block: khanakul-ii, district - hooghly under electrical division, phe dte.- 1 part-a supply and delivery at site submersible pumping machinery directly coupled with wet winding type submersible motor having the following specification pump.duty condition :36 cu.mtrhead :58 mtr.motor : submersible type 3 ph. 50 hz. 400v + 10%, mos:- star deltaimpeller : gm/ ss/ cromesteelmotor winding : wet type.pump outlet - 65/75/100 mm.(test certificate, warranty certificate along with characteristic curve should be submitted at the time of delivery.) 2 supply and delivery at site the following:-upvc 80 mm dia column pipewith both side square threaded (8 tpi)with one socket and o ring biax technology with wiring lock system non corrosive,high tensile having iso 9001 standard. 3 i)3 mtr. long. 4 ii) 1.5 mtr. long 5 iii) 80 mm dia top & bottom adaptor 6 100 mm x 80 mm dia gi reducer 7 supply and delivery at site heavy type suitable dia m.s. suspension clamp for above column pipe along with nuts, bolts and washers etc. 8 supply and delivery at site 80 mm. dia cidf sluice valve- 1 no., 80mm non return valve (swing type - 1 no.) pn - 1.0,80mm ms heavy flange - 1 no., cidf bend 90o - 1 no., cidf / ms (heavy) short piece as required length, 80mm cidf tee - 1 no., reducer, nut bolt and other ci / ms specials etc. as required as per i.s. specification and other required materials for the job i.e. for making complete construction of delivery and wash out lineas per relavant i.s. (test certificate for valve should be submitted at the time of delivery). 9 supply and delivery at site split type m.s. fabricated suitable tubewell cover for the tubewell housing with necessary clamping arrangement including holes for column pipe, air pipe and cable entry etc. 10 supply and delivery at site depth gauge (make : h. guru) 102 mm dia. with steel airbreak pipe required length with all other fittings and accessories for the work including supplying on the good quality hand pump of approve make 11 supply and delivery at site pressure gauge 102 mm. dia and 7 kg. /cm2 range, brass cocks and fitting complete(h.guru) 12 supply and delivery at site 4 sq. mm. 3 core copper 1.1 kv grade pvc insulated water proof flat submersible cable. 13 making safety device for above pump by supplying 3 nos. suitable size ms clamp/ ms cage and 1 dia nylon rope of required length including supplying nuts, bolts, and other materials as per direction. 14 supply & delivery of double flanged three phase 50 hz quarter turn electrical actuator [gear case lubrication : sp68 is:13095, torch switches: 2 x 1 no / 1 nc changeover contact, positional limit switches: 2 x 1 no / 1 nc changeover contacts] operated flange type butterfly valve (pn - 1.0) 80 mm. dia with mechanical position indicator, ci body & disk - is: 210 gr. fg 260, shaft of stainless steel aisi 410 as per bs 5155 ip - 68 / s-2,(test certificate should be submitted at the time of delivery) 15 supply & delivery of 415 v mcc cum pdb. with minimum 2mm thickness and degree of protection ip - 54, conforming to is-8623 withsuitable bus bar, digital voltmeter ammeter, contactor, delay timer, mcb, valve actuator starter etc. with plc logic & ups as detailed in annexure - i7.5 -12.5 hp with sds (star delta starter)panel make : digitek / rnr industries /pce projects / opg power system / ecs.[tc / gc to be submitted along with panel after approval of detail power and control circuit drawing by eic]. 16 supply & delivery of 35 sq. mm. 3 1/2 core pvc insulatedal. armoured cable (1.1 kv grade), is 1554 (part - i) / is 7098 (part-i) make : incab /gloster / nicco / polycab / crystal. 17 supply & delivery of 100 amp. 440 v, 50 hz. tpn main switch with rewireable type fuse link 18 supply & delivery of 100 amp. industrial copper busbar 19 supply & delivery of 4 pole 100 amp changeover unit 20 supply & delivery of 100 amp 4 pole mccb with adjustable overload and adjacent short circuit protection including enclosures. 21 supply & delivery at site of 25 kva, 3 phase oil cooled type servo motor operated wound line voltage corrector conforming to is-9815 [pt-i] 1994 suitable for unbalanced input voltage.input voltage: 3 phase main supply phase to phase 200v-500v 3 servo motor in 3 phase with all protection by mcb (make- abb / siemens/ l&t)output voltage: 3 phase balanced output phase to phase 415v + 1% (test certificate & warranty certificate should be submitted at the time of delivery) 22 supply and delivery of automatic plunger type chlorinator for feeding accurately automatic controlled dosage of chlorine solution into the water by connecting metering pump with flow rate of water 0-100 ltr/hr. with maximum pressure of 10 kg./cm2 suitable dosing pump and other necessary accessories on the delivery pipe line as required. the pump shall be coupled with 1/2 hp motor having 3 phase power and 1440 rpm (+4%).(test certificate will be submitted at the time of delivery) 23 part-binstallation of pumping machinery with valves, pipe & pipe specials, sort piece, presurre gauge including hoisting of column pipe making all electrical and water line interconnection complete as per direction including supply of necessary materials as required for the work. 24 making of tubewell foundation (size- 3x 3x 3.5 approx) as per site situation including supply of necessary materials as bricks, sand, cement, stone chips etc. with plastering & neat cement finishing to complete as per direction. 25 installtion of panel & actuator operated ci butterfly valvewith supply of 12 core 2.5 sq. mm. copper control cable, compensating ms flange, nuts, bolts gasket and other fixing materials as required to complete the job including necessary making of brick pillar as per site situation with supply of necessary materials like bricks, sand, cement, stone chips etc. with plastering & neat cement finishing in all respect including successfull operation along with testing of the whole installation as per entire satisfaction of eic. 26 installation with testing and commissioning of the voltage stabilizer with necessary foundation along with necessary accessories in the suitable position and drawing cable with ms shaddle, making all electrical connection including socketing, crimping to complete the work as per direction. 27 installation of above supplied chlorinator pump set and drawing of power line by supplying of necessary wire and continuous earthing connected to auto/ manual panel. this includes the cost of making necessary brick foundation base with neat cement finish by supplying all requered materials and testing entire set as per direction of eic 28 making internal electrification with 16amp main switch/mcb (make: havells/ any approved) by 1.5 sq.mm frlsh grade copper pvc insulated single core multistrand wire (make: havells/ mescab/ finolex/ any approved) in pvc casing of pump house consisting of 2 nos. bracket point, 1 no. tube light point, 1 no. bulk head point and 1 no. five pin 5 amp. socket point, 1 no. ceiling fan point with controlling switches including supply of 2 nos. bracket with 12w led lamp, 1 no. 20 watt led tube light set, 1 no. outdoor type bulk head with 9w led lamp and drawing of necessary earthing (1.0 sq.mm) material all complete as per direction eic. (led light make: philips/ havells/ any approved) 29 supply and fitting fixing of 45 watt. x 2 nos. led light set [make - philips, model: brp031 led45 cw slr gr psu] with 2 nos 40 mm dia 1.5 mtr. long g.i pipe bracket fixed on the roof of the pump house with properly grout including making power connection by 2 x 1.5 sq. mm copper fr grade flexible wire through pvc casing/conduit with drawing earth conductor (1.0 sq mm copper flexible wire), fitting fixing of 15 amp switch on board with all complete as per direction of eic. 30 earthing confirming to is: 3043 by 50mm dia gi pipe 3.64mm thick x 3.04m long and 1 x 4 swggi (hot dip) wire (4 mts. long), 13mm dia x 80mm long gi bolts, double nuts, double washers including supply & fixing of 15mm dia gi pipe protection (1 mtr long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 mtrs below the ground level and restoring surface duly rammed as below. a) for soft soilby tata - medium gi pipe 31 drawing earth by m.s. flat strip (20mm x 3mm) fromearth bus / electrode to above differentcomponents as per i.e. rules and as per direction of eic. 32 supply & fitting fixing of 100 amp. kit kat (3 nos.)(make : havells) with required size wooden board mounted on wall. 33 supply, delivery & fitting fixing of 48 sweep 230 volt, 50 hz, ac ceiling fan (make : havells/ cg/ approved make) including fitting fixing on ceiling and making electrical connection complete. 34 supply & delivery at site 2 nos. plastic chair & 1 no. plastic table (make: cello / supreme / nilkamal) 35 trial operation and guarding of whole installationas per departmental requirement and guideline 1 no. operator @ 465/- per day with 8.33% bonus. [as per existing departmental terms & conditions] 36 add: 18% gst 37 add: 1% cess

Central Government/Public Sector

TRN :49059764 | 24 Jun, 2025

Tender Value : 0

Gonda - Uttar Pradesh

Tender for supply of set of gasket for oil circuitset of gasket for oil circuit,set of gasket for oil circuit joint of transformer type hett-5400 as per drg . no. a3/04/cnb/1898/5133/gk/alt-c, one set consisting of 06 items : 18 nos.(1)rubber gaske t for mph vent nipple qty-04 nos. (2) rubber gasket for conservator 3 way cock connec tion qty-04 nos (3) rubberised cork gasket for radiator priming pipe joint qty -02 nos.(4) rubberised cork gasket for radiator flange qty- 02 nos.(5) rubberised cork gasket for radiator bend qty- 02 nos. (6) rubberised cork gasket for mph flange qty-04 nos. [ warr anty period: 30 months after the date of delivery ] ] amm/els/gonda, ner uttar pradesh 200.00 set

State Government

TRN :49060859 | 15 May, 2025

Tender Value : 0

Mannuthy - Kerala

Tender for supply of furniture at vkidft auditorium, cdst mannuthy.-- civil 2 od142954/2023_2024 : supplying teak wood podium of size 60x40x120cm of approved design and pattern including all cost of design works ,polishing, conveyance etc. complete as per direction of engineering charge. 3 od144194/2023_2024 : supplying and fixing chair of back frame with 660mmx430mm made with 20mmx20mm 16swg tube, pu injection moulded foam average 2-2.5 thick with head rest & lumbar support of 50-52 kg/cum, with back cover ppcp injection moulded & frames stripped with 22 swg sheet to support foam and all metal portions powder coated. and seat frame of 430mm x430mm made with 25mm x 25mm pipe 18swg, pu injection moulded foam of 430mmx430mm average 3-3.5 thick of 55-56 kg/cum, bottom side covered with and frames stripped with 22 swg sheet in suitable spacing and topped with 3mm hard board to support pu foams and metal portions powder coated. and side stand of 600mm x 400mm fabricated with 25mm x 25mm 18 swg pipe and 40x6 mm ms flat for foundation fabricated to shape, pu or ppcp bend(without cupholder) arm rest and all end passage viewing stand will be fully upholstery covered up to bottom and all inside legs half portion upholstery with 5mm hardboard and all metal parts powder coated. and roller and box type, roller of 14mm thick nylon casted noise free treated metal roller and box 2 nos.each made fabricated with 50mm x 3mm thick flats, 20mm x20mm 18 swg pipe 2 stays, provided with coil springs/hydraulic gas springs and of lacquer paint finished or powder coated. and upholstery of 3mm foam laminated fabric of approved shade of special fabric made for theatre seatig 4 od144213/2023_2024 : supplying and fixing removable type cover for chair head rest of best quality cotton/polyester type material with approved style and designed logo and letters inscribed as per the direction of engineer in charge. 5 od144468/2023_2024 : supplying and fixing stainless steel letters of overall size 50mm height and 50mm width and letter thickness of 30mm with necessary fitting arrangements to podium as per the direction of engineer in charge including all cost of materials, conveyance and labour charges etc complete. 6 od145588/2023_2024 : supplying teapoy of size 90x60x45 cm with teak wood frames and 8mm thick cooling glass top, all as per the direction of engineer in charge including all conveyances 7 od145711/2023_2024 : supplying and fixing zeebra blinds of approved colour and quality for openings including all cost of material, labour etc. as per the direction of engineer in charge. 8 od145742/2023_2024 : supplying teak wood executive chair of size 60x110 cm of approved pattern with best quality cloth covered cushion on seat and back, all as per the direction of engineer in charge including all conveyances 9 od145857/2023_2024 : supplying teak wood executive chair of size 56x100 cm of approved pattern with best quality cloth covered cushion on seat and back,all as per the direction of engineer in charge including all cost of design work, polishing, conveyance etc. complete. 10 electrical 11 od146997/2023_2024 : supply of 450mm sweep, heavy duty domestic type pedestal fan of reputed make (almonard or equivalent)all as per the direction of engineer in charge

Government Departments

TRN :49061056 | 13 May, 2025

Tender Value : 0

Bilaspur - Uttar Pradesh

Tender for supply of hardware and mechanical items season 2025-26 , supply of hardware , esab/asha isi wellding accessories as ppl maximum discount wef…. , carboraudum universal make grinding wheel as ppl maximum discount wef…. , miranda make hss tool bit cobalt 10%as ppl maximum discount wef…. , j.k. make files as ppl maximum discount wef…. , jhalani make hand tool as ppl maximum discount wef…. , addison/ it make tst drill as ppl maximum discount wef…. , totem make tap set as ppl maximum discount wef…. , champion make spring washer/spilt pin as ppl maximum discount wef…. , maharastra seemless make ibr pipe schedule 40 and 80 as ppl maximum discount wef…. , sanvik make carbide tip as ppl maximum discount wef…. , unique make:- tyre couplingas ppl maximum discount wef…. , unique make spare tyre as ppl maximum discount wef…. , fanner make gear coupling as ppl maximum discount wef…. , sant make caststeel/gun metal valve as ppl maximum discount wef…. , jmc make bearing sleeves as ppl maximum discount wef…. , unbrako make hightensile bolt/allenkey bolt/ stud/ nut as ppl maximum discount wef…. , ss bolt and nut as ppl maximum discount wef…. , ss allenkey bolt as ppl maximum discount wef…. , hindustan composite break liner ba quality as ppl maximum discount wef…. , felt belt goodyear/dunlop as ppl maximum discount wef…. , m.s bolt full thread inch all size std quality , m.s bolt half thread inch all size std quality , m.s bolt mmall size std quality , m.s nut inch size std quality , m.s nut mm size std quality , m.s plane washer all size , rubber joint jyoti make all size , standard rubber joint all size , emery colth carborundum make rough , emery colth carborundum makefine , emery paper carborundum make rough , emery paper carborundum make fine , emery tape carborundum make rough 2 inch , emery tape carborundum make fine 2 inch , emery colth john ok rough , emery colth jhon ok fine , emery paper jhon ok rough , emery paper jhon ok fine , emery tape jhon ok rough 2 inch , emery tape jhon ok fine 2 inch , aligator no. 27 (ameteep) , aligator no. 35 (ameteep) , aligator no. 45 (ameteep) , all kind of welding accessories isi make , araldite 180 gm , araldite 550 gm , rustoline 500 ml , emery paste rough & fine 400 gm , graphited powder & molykot , locktite 641 no , aluminum rivetsany sizes , ana bond 666 , bb coupling spring for fibrizer , brass brazing rod 1/16 (silicon brazing) , brass brazing rod 1/8 (silicon brazing) , brass ferrule connector nut union , brass ferrule size 1/4 as per sample , brass ferrule size 5/16 as per sample , brass nut size 1/4 as per sample , brass nut size 5/16 as per sample , brasso 100 ml. , copper flexible jumper size-12x100mm , copper pipe all sizes , copper revit assorted size , corrugated plastic pipe with nylon thread good qualitysize 1/2 , corrugated plastic pipe with nylon thread good quality size 1/4 , corrugated plastic pipe with nylon thread good quality size 3/4 , cotton waste coloured good quality , cotton waste white good quality , counter shank bolt all size , crc 226 , drum mandrel drive , emery cloth/paper fine 1½ john okay isi , emery cloth/paper fine 2john okay isi , emery cloth/paper rough , essab ruptam-a silber brazing flux , extruded brass rod any sizes , canvas fire house pipe 30 mtr rrl with 5.5 male & female cupline isi 0 mek make , gauge glass for texmaco boiler size 3/4 x 16½ good quality (borosil make) , gauge glass klinger make b-9 with gasket , glass wool , good quality flat belt (patta) ferrodo make size 3 ply x 2 , good quality flat belt (patta) ferrodo make size 4 ply x 2½ , good quality flat belt (patta) ferrodo make size 5 ply x 4 , good quality flat belt (patta) ferrodo make size 6 ply x 5 , good quality flat belt (patta) ferrodo make size 8 ply x 6 , graphite power in 500gm packing , h.t. bolt all size , h.t.nut all size , hexa blade (l.a make) size 1/2 x 12 , hexa blade good quality size 1/2 x 12 other make ----------------- , hexa frame for above , high pressure steel stand class -300 ibr-12 hali , high pressure wire breaded steam hose pipe size 1 indoaction , holdtite liquid compound 500gms (pidilite) , hose clamp 2-1/4 , local rubber hose pipe 2 ply 24mm , index make chain pulley make heavy duty p-series 02 ton x 10 mtr. , j.k. make files & tools , jhalni make pipe wrinch 24 , klinger make high pressure jointing sheet metaliic 3 mm , red lead standard , lead ingot (white) , leatherised paper good quality , lock tight 242 , lock tight 270 , lower plunger for c/f machine , m. seal kg. pack(pidilite) , lr.b. pad heaving density 100 kg, 2 inch thick , m. sealmahindra & mahindra , m.s. flange- (14)” od-533, pcd-476,bore- 350 no. of hole-12, hole size- 22mm, thickness- 20mm , m.s. flange- (2)” (standard size) , m.s. flange- (3)” (standard size) , m.s. flange- (4)” (standard size) , m.s. flange- (6)” od-285, pcd-235, no. of hole-8, hole size- 19mm, bore- 150mm thickness- 12mm , manila rope pully size 3/4 x 2 groove , manila rope pully size 3/4 x 3 groove , manila rope tested quality size 1/2 , manila rope tested quality size 3/4 , markeen cloth , measuring tape 10 mtr , measuring tape 15 mtr , measuring tape 3 mtr , measuring tape 5 mtr , measuring tape-3 mtr , mechanical oil seal with spring sealing (for monoblock pumps) size-(20-31-08) as per sample , metalic oil seal 120-150-15 , metalic oil seal 180-210-15 , metalon sheet standard size , mill hydraulic pipe high pressure od 18 mm, bore 11 mm tested 500 kg/cm2 , moly-kote spray 1000 per metal 225ml. pack , ms bolt best quality all size - inch size , ms bolt best quality all size - mm size , ms bolt with nut inch size , ms bolt with nut mm size , ms connector for hydraulic system , ms counter shank bolt all sizes , ms elbow 1 (forged) , ms elbow 1/2 (forged) , ms elbow 3/8 (forged) , ms flange table e size 6 , ms long bend c class 1 , ms long bend c class 1-1/2 , ms long bend c class 2 , ms long bend c class 2-1/2 , ms longt bend c class 3 , ms long bend c class 4 , ms long bend c class 5 , ms long bend c class 6 , ms long bend c class 7 , ms long bend c class 8 , ms long bend c class 9 , ms long bend c class 10 , ms long bend c class 11 , ms long bend c class 12 , ms per forated sheet size 4 x 8, 10 mm hole x 8 thick , ms pipe msl make high pressure steam pipe (sch. 40) size 6 with ibr certificate , ms plain washer all sizes , ms rivets assorted size , ms short bend c class 1 , ms short bend c class 1-1/2 , ms short bend c class 2 , ms short bend c class 2-1/2 , ms short bend c class 3 , ms short bend c class 4 , ms short bend c class 5 , ms short bend c class 6 , ms short bend c class 7 , ms short bend c class 8 , ms short bend c class 9 , ms short bend c class 10 , ms short bend c class 11 , ms short bend c class 12 , ms split pinall sizechanpion make , ms stud all size , ms union socket 1 heavy duty forged quality , ms union socket 1/2 , ms union socket 1/4 , ms union socket 3/4 , woolen 1/2 , nose mask for welder , nylock nut size ½” , nylock nut size ¾” , nylock nut size 1” , nylock nut size 5/8 , nylock nut size24 mm , nylock nut size 22 mm , oil seal mykoda make all size , old dhoti (cotton) 5 mtr , asbestesleder , painting brush size 1 , painting brush size 2 , painting brush size 3 , painting brush size 4 , painting brush size 5 , painting brush size 6 , piano wire ss , pluge sleeve packing for water gauge sleeve packed type (for valve cock & boiler mountings make-qinn) , plumber block (smr) , polyproplene rope 3/4 tested quality , power master make tube expander suitable 100 mm tube , power master make tube expander suitable 42 mm tube to 45 , power master make tube expander suitable 48 mm tube , power master make tube expander suitable 63 mm tube , power master make tube expander suitable 80 mm tube , power master tube expender with ratchet for 48.4 id x 1.5 mm thik. , pvctransparent pipe good quality size 1” , pvctransparent pipe good quality size 2 , pvctransparent pipe good quality size 3/4 , pvc transparent roller, ø 1”x bore 3/16” as per sample , pvc transparent pipe good quality size 1/2 , quick setting cement fosroc make (25kg.) bag. , ranga , round sight glass grinded & polished in 12 mm thk.x 9 3/4 , round sight glass grinded & polished in 12 mm thk. x 43/4 out dia. , round sight glass grinded & polished in 12 mm thk. x 5 , round sight glass grinded & polished in 12 mm thk. x 7 , round sight glass grinded & polished in 20 mm thk. x 8 ½ , round sight glass grinded & polished in 20 mm thk. x 8¼ , round sight glass grinded & polished in size 12 mm thk. x 4 out dia. , round sight glass grinded & polished in size 12 mm thk. x 6 out dia. , rubber cone for above glage glass , rubber hose pipe standard size 1/2 , rubber hose pipestandard size 1” , rubber hose pipestandardsize 1¼ , rubber hose pipestandard size 1½ , rubber hose pipe dunlop/indo/vardhman size 3/4 , rubber hose pipe dunlop/indo/vardhman size 7/8 , rubber insertion jyoti brand all size , rubber joint black sheet all size , rustolene 500 ml (hard castle) , seamless pipe 12 nb sch 100 wall thickness - 21.44 mm , seamless pipe 4 nb sch 80 wall thickness -8.56 mm , seamless pipe msl make sch-40 size 1 , seamless pipe msl make sch-40 size 1½ , seamless pipe msl make sch-40 size 3/4 , shallac compound 50 gm tube , sight glass 105x10 mm , sight glass 125x19 mm , sight glass 200x15 mm , sight glass 210x15 mm , simplex chains(renynold make) diamond , simplex chains(renynold make) 2 diamond , solonide coil for solonide valve , split pin 1/8 x ½” as per sample champion , split pin 1/8x1/2” as per sample champion , spring steel flat any size , spring washer champion make , ss bolt & nut all sizes 304 grade , ss nut all size inch size/mm size 304 grade , ss rod above 2 size 304 grade , ss rod upto 2 size 202 grade , ss socket 1/2 , ss socket 1/4 , ss stud size 5/8 x 2½ , ss stud size 5/8 x 3 , stainless steel hydrent valve for fire fitting water supply single way flange type , steel wire brush (hand) , straight grinder 4 bosch/raw wolf , taflon rodsize 1¼ x 12 , taflon rod 2x1/2 , taflon rod size 1 x 12 , taflon rod size 1/2 x 12 , taflon rod size 1½ x 12 , teflon rod 2 ½” x 300 mm , thermameter 0-110 red line size 12 long , totem make tap set hss all sizes , tst /sst drill (it make) adision / it , tube expender spares suitable for model-140-a62/2, 2x7-8 g, ½-7/8 t-5 , u clamp 1/2 forged for unloader wire rope , u clamp 3/4 forged for unloader wire rope , usha martin make steel wire rope 3/4 hemp core 6/19 with test certificate , usha martin make steel wire rope 3/4 hemp core 6/37 with test certificate , valve grinding paste fine 400gms (c/u) , valve grinding paste rough 400gms (c/u) , wire breaded rubber house pipe with end connection size 1/2x 1 mtr. long , wire breadedrubber house pipe with end connection size 1/4 x 300 mm long , wire breaded rubber house pipe with end connection size 1/4 x 400 mm long , wire breaded rubber house pipe with end connection size 3/4 x 400 mm long , wire breaded rubber house pipe with end connection size 3/8 x 1 mtr. long , wire breaded rubber house pipe with end connection size 3/8 x 1.5 mtr. long , wire breaded rubber house pipe with end connection size 3/8 x 400 mm long , wire breaded hose with end connection both sides insize 1 x 1000 mm long , wire breaded hose with end connection both sides insize 1 x 500 mm long , wire breaded hose with end connection both sides insize 1/2 x 1000 mm long , wire breaded hose with end connection both sides insize 1/2 x 500 mm long , wire breaded hose with end connection both sides insize 1/4 x 1000 mm long , wire breaded hose with end connection both sides insize 1/4 x 500 mm long , wire breaded hose with end connection both sides insize 1/8 x 1000 mm long , wire breaded hose with end connection both sides insize 3/4 x 1000 mm long , wire breaded hose with end connection both sides insize 3/4 x 500 mm long , wire breadedhose with end connection both sides in size 1/8 x 500 mm long , wire breaded rubber hose pipe steam double braded 1/4 , wire breaded rubber hose pipe steam single wire braded , wolf make tools hand grinder ag 7/straight grinder etc. , wolf make tools spares field/carbon brush/armature , copperroad all size , brass road , hole tight 500 gm

corporations/Associations/Others

TRN :49061687 | 29 May, 2025

Tender Value : 0

Sonbhadra - Uttar Pradesh

Tender for tender for annual maintenance of ash dyke of obra thermal power station. - earth work in excavation by mechanical means (hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. all kinds of soil 2 excavation work by mechanical means (hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m. ordinary rock 3 filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. 4 filling of empty jute/plastic bag in full with full stitching with nylon thread and stacking in crate from any where inside/outside ash pond including cost of all labour, material, t&p etc. 5 filling with 50kg. earth 6 filling with 50kg. ash 7 clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. 8 surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. all kinds of soil. 9 providing & making gabion structure with mechanically woven double twisted hexagonal shaped wire mesh gabion boxes as per is 16014:2012,morth clause 2500, of required size, mesh type 10x12(d=100 mm with tolerance of ±2%), zinic+10% al alloy+pvc coated, mesh wire diameter 2.7/3.7mm (id/od), mechanically edged/ selvedged with partitions at every 1m interval and shall have minimum 10 numbers of openings per meter of mesh perpendicular to twist, tying with lacing wire of diameter 2.2/3.2mm(id/od), supplied @3% by weight of gabion boxes, filled with boulders with least dimension of 200 mm, as per drawing, all complete as per directions of engineerin-charge. 10 random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with :cement mortar 1:6 (1 cement : 6 coarse sand) 11 dry stone pitching 22.5cm thick including supply of stones and preparing surface complete work 12 dry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete :with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 13 centering and shuttering including strutting, propping etc. and removal of form for :foundations, footings, bases of columns, etc. for mass concrete 14 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level :1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) 15 providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-iii) : 4 graded stone aggregate 20 mm nominal size) 16 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.thermo-mechanically treated bars of grade fe-500d or more. 17 supplying and stacking at site 63 mm to 45 mm size stone aggregate 18 supplying and stacking at site moorum etc. 19 laying, spreading and compacting stone aggregate of specified sizes to wbm specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density 20 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in foundation and plinth in: cement mortar 1:6 (1 cement : 6 coarse sand) 21 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :one or more coats on old work 22 12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand) 23 engagement ofunskilledlabourfor executed the unforeseen works . 24 providing hydraulic excavator with 1 cum bucketfor different type of job related to chakari ash dyke and required another workas per direction of engineer-in-charge including hire charge of hydraulic excavator with operator,fuel, lubricant etc for proper completion of work.

Government Departments

TRN :49061799 | 13 May, 2025

Tender Value : 0

Bilaspur - Uttar Pradesh

Tender for supply of supply of ci gm and cs casting for season 2025 26 , supply of ci, gm & cs casting items for season 2025-26 , c.i. coupling with pilot bore 12” conversion basis , c.i. coupling with pilot bore 12” fresh supply , 16 teeth sprocket 2” pitch as per drg on conversion basis , 16 teeth sprocket 2” pitch as per drg on new supply , a) g. m. bari and bush gulla on conversion basis , b) gun metal bari and bush gulla new supply fresh , brake assembly brake drum 8” , c) gun metal bari and bush gulla machining charges different size , c.i. casting for boiler purpose as per drg. suitable for boiler use conversion base , c.i. casting for boiler purpose as per drg. suitable for boiler use fresh supply , c.i. casting for boiler purpose as per drg. suitable for boiler use machining charges , c.i. chute for boiler (mouth piece) as per drg.dully machinedconversion base , c.i. chute for boiler (mouth piece) as per drg.dully machined fresh supply , c.i. chute for boiler (mouth piece) as per drg.dully machined , c.i. cross,tee, bends (machining) conversion basis , c.i. cross,tee, bends (machining) fresh supply , c.i. drum of unloder no-2 bridge drg. no.-rb/m-173-a , c.i. gulla all sizes conversion base , c.i. gulla all sizes fresh supply , c.i. gulla all sizes machining charges , c.i. hanger for lipi/texmaco make boilers as per drg on conversion basis , c.i. hanger for lipi/texmaco make boilers as per drg on new supply , c.i. idler pully as per drg. proof machined conversion base , c.i. idler pully as per drg. proof machined fresh supply , c.i. idler pully as per drg. proof machined machining charges , c.i. muff coupling as per drg. fresh supply , c.i. muff coupling as per drg.conversion base , c.i. muff coupling as per drg.machining charges , c.i. scraper texmaco/iseg mill as per drg. proof machined texmaco/iseg conversion baseis , c.i. scraper texmaco/iseg mill as per drg. proof machined texmaco/iseg fresh supply , c.i. scraper texmaco/iseg mill as per drg. proof machined texmao/isegmachining charges , c.i. ventury as per drg. duly machining & drilling , c.i. warm & warm wheel, no. of teeth of wheel 62, no. of teeth of warm 4 1/2, as per drawing rb/m-118a , c.s. bearing housing for isgec mill for top roller as per drg conversion base , c.s. bearing housing for isgec mill for top roller as per drg fresh supply , c.s. bearing housing for isgec mill for top roller as per drg machining charges , c.s. bearing housing for isgec mill side roller as per drg conversion base , c.s. bearing housing for isgec mill side roller as per drg fresh supply , c.s. bearing housing for isgec mill side roller as per drg machining charges , c.s. bearing housing for texmaco mill side roller as per drg. no. 258 conversion base , c.s. bearing housing for texmaco mill side roller as per drg. no. 258 fresh supply , c.s. bearing housing for texmaco mill side roller as per drg. no. 258 machining charges , c.s. bearing housing for texmaco top half roller as per drg. no. rbm-50 conversion base , c.s. bearing housing for texmaco top half roller as per drg. no. rbm-50 fresh supply , c.s. bearing housing for texmaco top half roller as per drg. no. rbm-50 machining charges , c.s. bridge wheel forcane unloader as per drg. , c.s. drum of unloder no-2 bridge drg. no.-rb/m-173-a , c.s. gear & pinion 25mm pitch cane unloder as per drg on conversion basis , c.s. gear & pinion 25mm pitch cane unloder as per drg on new supply , c.s. gear 1 ½” pitch, 25 teeth , c.s. trolley wheel forcane unloader as per drg. , c.s.casting croun piniun grade is 2708 as per drg conversion base , c.s.casting croun piniun grade is 2708 as per drg fresh supply , c.s.casting croun piniun grade is 2708 as per drg machining with teeth profile , c.s.casting mill copling grage is 2708 conversion base , c.s.casting mill copling grage is 2708 fresh supply , c.s.casting mill copling grage is 2708 machining charges , c.s.casting trash plate as per drg conversion base , c.s.casting trash plate as per drg fresh supply , c.s.casting trash plate as per drg machining charges , c.s.gear with pinion gear teeth-60 nos. pinion teeth-22 nos, drg no-rb/m-40 , c.s.gear with pinion gear teeth-64 no. pinion teeth-18 no, drg no-rb/m-01 , c.s.gear with pinion for m.b.c no of teeth on gear-99 no of teeth on pinion-22,pitch-38mm face width-135mm as per drg. , c.s gear set no of teeth on big gear-20, no of teeth on smaller gear-17 pitch-164.85mm face width-95mm , c.s.pinion of crass carrier no of teeth -15 pitch-26.69 mm drg no. rb/m-312 , c.s.pinion of crass carrier no of teeth -17 pitch-26.69 mm drg no. rb/m-311 , c.s.sprocket 2” pitch 12 teeth sprocket as per drg on conversion basis , c.s.sprocket 2” pitch 12 teeth sprocket as per drg on new supply , c.s.sprocket 2” pitch 17 teeth sprocket as per drg on conversion basis , c.s.sprocket 2” pitch 17 teeth sprocket as per drg on new supply , c.s.sprocket 38mm pitch no.of teeth-25 drg. no-rb/m-147 new supply , c.s.sprocket 38mm pitch no.of teeth-25 drg. no-rb/m-147 on conversion basis , c.s.sprocket for bagasse elevator 38mm pitch no.of teeth -95 drg. no-rb/m-247 on conversion basis , c.s.sprocket for bagasse elevator 38mm pitch no.of teeth -95 drg. no-rb/m-247 on new supply , cs pinion cross carrier no of teeth-15, pitch-26.69mm drg.no-rb/m-312 , cs pinion of cross carrier no of teeth-17, pitch-26.69mm drg no. rb/m-311 , g.m. bearing/bearing liner for texmaco & isgec mill as per drg. conversion base , g.m. bearing/bearing liner for texmaco & isgec mill as per drg. fresh supply , g.m. bearing/bearing liner for texmaco & isgec mill as per drg.machining charges , grooving of top & dis. scraper mill texmaco & isgec make as per drg. , m.s. channel/fins w/m type for boiler chimney new supply , s.s. channel/fins w/m type for boiler chimney new supply , teeth cutting in discharge scraper of texmaco/isgec mill.

State Government

TRN :49062033 | 13 May, 2025

Tender Value : 2.34 Lacs

Paravur - Kerala

Tender for tender for pakarappally devaswom - paravur group - constructing toilet block-- 1 appendix i-constructing toilet block 2 earth work in excavation by mechanical means (hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.all kinds of soil 3 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size) 4 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level:1:1/2:3 (cement : 11/2 coarse sand : 3 graded stone aggregate 20 mm nominal size) 5 centering and shuttering including strutting, etc. and removal of form for:foundations, footings, bases of columns, etc for mass concrete 6 solid block masonry using pre cast solid blocks (factory made) of size 30x20x15 cm or nearest available size confirming to is 2185 part i of 1979 for foundation and plinth with thickness 15cm in: cm 1:6 ( 1 cement :6 coarse sand) etc complete 7 providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size 8 steel reinforcement for r.c.c work including straightening, cutting, bending, placing in position and binding all complete upto plinth level thermo - mechanically treated bars of grade fe-500d or more 9 solid masonry using pre cast solid blocks (factory made) of size 30x20x15cm or nearest available size confirming to is 2185 part i of 1979 for super structure up to floor two level with thickness 15cm in : cm 1:6 ( 1 cement : 6 coarse sand) etc complete 10 reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 150 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (zone iii) : 3 graded stone aggregate 20 mm nominal size). 11 centering and shuttering including strutting, etc. and removal of form for:lintels, beams, plinth beams, girders bressumers and cantilevers 12 steel reinforcement for r.c.c work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelthermo - mechanically treated bars of grade fe-500d or more 13 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) 14 providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.size of tile 600 x 600 mm. 15 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineerin-charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 16 providing and fixing water closet squatting pan (indian type w.c. pan) with 100 mm sand cast iron p or s trap, 10 litter low level white p.v.c.flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever require:white vitreous china orissa pattern w.c. pan of size 580x440 mm with integral type foot rests 17 supplying and fixing cp towel rod 45cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site engineer-in-charge. 18 providing and fixing white vitreous china pedestal type water closet (european type w.c. pan) with seat and lid, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:w.c. pan with isi marked white solid plastic seat and lid 19 providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:white vitreous china flat back wash basin size 550x400mm with single 15 mm c.p.brass pillar taps 20 finishing walls with acrylic smooth exterior paint of required shade:new work (two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 21 supply and fixing pvc door with frame including locking arrangements as per the direction of engineer-in-charge 22 providing and fixing m.s. grills of required pattern in frames of windows etc. with m.s. flats, square or round bars etc. including priming coat with approved steel primer all complete.fixed to openings/ wooden frames with rawl plugs screws etc 23 providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per is: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by engineer-in-charge. the sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with epdm seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 24 structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 25 providing and placing on terrace (at all floor levels) polyethylene water storage tank :isi 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 26 supplying and fixing cp health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge. 27 providing and fixing c.p brass bib cock of approved quality conforming to is: 8931.15 mm nominal bore 28 providing and fixing c.p. brass shower rose with 15 or 20 mm inlet:100 mm diameter 29 appendix ii-septic tank and soak pit 30 supplying and installing ready made pvc septic tank including the cost of carriage, trenching, placing at the level below ground level as specified as per the direction of engineer in charge (provision for cc/rcc/sand/06mm aggregate for the preparation of bed shall be paid separately. 4.35 to 50 flush capacity

Related Searched Keywords : u bend

List of u-bend Tenders

Get u bend Tender Alert...

Related Searched Keywords : u bend

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us