Filters

List of ms-roller Tenders

List of latest ms-roller Tenders in Indian Tenders. Click on any ms-roller Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for ms-roller Tenders.

All-Tenders (53)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

Local Bodies

TRN :49021556 | 16 May, 2025

Tender Value : 21.17 Lacs

Hathras - Uttar Pradesh

Tender for tender for cc work from nagla khushali marg to lakhanu pura marg ambedkar park in village panchayat lakhanu - clearing & grubbing road land including uprooting wild vegetation grass bushes shrubs sapling and trees of girth up to 300 mm 2 construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of tables 300.1 and 300.2 with a lead upto 1000 m as per technical specification clause 301.5(widening of patari) 3 excavation for roadway in soil using manual means for carrying of cut earth to embankment site with a lift upto 1.5m and lead upto 50m as per technical specification clause 302.3 4 providing concrete for plain concrete in open foundation complete as per drawings and technical specification clause 802,803,1202 &1203 5 plane/reinforced cement concrete in substructure complete as per drawings and technical specification clauses 802,804,805,806,807, 1202&1204 6 supply, fitting and placing with ms bar rainforcement as per drawings and technical cpecification clause 1002, 1010 and 1202 7 construction of granular sub-base by providing well graded material, spreading in uniform layers with tractor mountedgrader on prepared surface mixing by mix in place method with rotavator at omc, and compacting with smooth wheel roller to achieve the desired density, complete as per technical specification clause 401. 8 providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smoothwheel roller 80-100 kn in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per technical specification clause 405. 9 construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per clause 1501.2.2 m30 (grade), coarse and fine aggregates conforming to is:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, 10 supply and fixing of information board

Government Departments

TRN :49021952 | 15 May, 2025

Tender Value : 0

Rajnandgaon - Chhattisgarh

Tender for nit-60 defect liability works under mmgsvy pkg.no. mmgsy-bmr-dlp-01 in dist. bemetara-cutting of branches of trees shrubs and trimming of grass and weeds. trimming of grass and weeds from the shoulders/berms and disposing off the same to suitable locations as per technical specifications clause 1914 restoration of rain cuts restoration of rain cuts with soil, moorum gravel or a mixture of these, clearing the loose soil, benching for 300mm width laying fresh material in layers not exceeding 250 mm and compaction with plate compactor or power rammer to restore the original alignment, level and slopes as per drawings and technical specifications clause 1902 maintenance of shoulder (filling with fresh selected material)making up loss of material/irregularities on shoulders to the design level by adding fresh approved selected material and compacting it with appropriate equipment at omc upto a lead of 1000 m as per technical specification clause 1903 maintenance of shoulder (filling with fresh selected material)making up loss of material/irregularities on shoulders to the design level by adding fresh approved selected material and compacting it with appropriate equipment at omc upto a lead of 1000 m as per technical specification clause 1903 maintenance of wbm road including filling up of pot holes, ruts and rectifying corrugated surface, damaged edges and raveling as per technical specification clause 1906. prime coat providing and applying primer coat with bitumen emulsion (ss-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per technical specification clause 502 tack coat providing and applying tack coat with bitumen emulsion (rs-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with hydraulic broom as per technical specification clause 503. 20mm thick open-graded premix carpet using bituminous (vg/modified bitumen) binder providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of aggregate 13.2mm size (passing 22.4mm size sieve & retained on 11.2mm sieve and 11.2mm size (passing 13.2mm sieve and retained on 5.6mm sieve) either using penetration grade/ vg bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kn static roller capacity, finished to required level and grades to be followed by seal coat of either type a or type b or type c as per technical specification clause 508., viscocity grade (vg) bitumen specification as per is 73:2006 seal coat providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using type a, type b and type c as per technical specification clause 510, viscocity grade (vg) bitumen specification as per is 73:2006 maintenance of road signs maintenance of road signs by way of cleaning and repainting of mandatory/ requlatory / cautionary/ informatory and place identifications sign board as perdrawing and technical specification clause 1910. providing and fixing of typical pmgsy informatory sign board with logo as per mord specifications and drawing. three ms plates of 1.6 mm thick, top and middle plate duly welded with ms flat iron 25mm x 5m size on back on edges. the lower plate will be welded with ms angle iron frame of 25mm x 25mm x 5mm. the angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 swg sheet tubes posts duly embedded in cement concrete m-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. the top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 swg steel plate tube. all m.s. will be stove enameled on both sides. lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. all sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing clause 1701 and annexure 1700.1 cautionary, mandatory, informatory direction and place identification sign boards.semi-reflective traffic signs upto 0.90 sqmdirection and place identification signs up to 0.9 sqm size boardproviding and erecting direction and place identifications of semi reflective sign boards as per irc:67 made of 2 mm thick m.s. sheet duly stove enameled paint in white colour in front and grey colour on back with red reflective border of 70 mm width and required message, letters, figures with reflective engineering grade tape as per mord specifications of required shade and colour. supported and welded on 47 mm x 47mm of 12 swg square tube of 3050 mm height duly strengthened by 25 mm x 5 mm m/s flat iron on edges on back firmly fixed to the ground by means of properly designed foundations with m-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and technical specification clause 1701 reinforced cement concrete m15 grade kilometre stone/local stone of standard design as per irc:8 fixing in position including painting and printing, etc as per drawing and technical specification clause 1703 5th kilometre stone (precast) ordinary kilometer stone (precast) 200 m stone (precast) maintenance of culverts maintenance of hume pipe culvert by way of clearing, cleaning,erosion repair, repairs to cracks, parapet wall and protection work as per drawing and technical specification clause 1908. maintenance of culverts slab type maintenance of slab type culverts by way of clearing, cleaning,erosion repair, repairs to cracks, parapet wall and protection work as per drawing and technical specification clause 1908. white washing two coats on parapet walls of cd and tree trunks including preparation of surface by cleaning scraping etc. as per technical specifications clause 1915 backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification clause 1204.3.8i. granular material

State Government

TRN :49024279 | 14 May, 2025

Tender Value : 0

Firozabad - Uttar Pradesh

Tender for tender for repair work in government high school niyamatpur firozabad under alankar yojana - dismantling doors and windows leaves including chaukhats but excluding hold fasts and including stacking of materials as directed by engineer-in-charge within a distance of 60 meters (200 feet) ch-17 -si no. 15 (705) 2 dismantling existing plaster including disposal of refuse as directed by engineer-in-charge within a distance of 60 meters. ch-17 -si no. 16 (706) 3 earthwork in excavation in trenches for foundation pipes cable etc. in ordinary soil, including lift upto 1.5 m lead upto 50 m and dressing of sides and ramming of bottom and disposal of surplus excavated earth including all labour, t&p etc. for proper completion of work, as directed by engineer incharge. (si. no. 251) 4 class-150 brick work in 1:3 cement and coarse sand of 1.25 fm mortar in super structure including necessary moulding and cutting of bricks as required including supply of all materials, labour and t&p etc. required for proper completion of the work thickness of wall of half brick thick.ch-6 -si no. 2(6.1) 5 providing and laying in cement concrete 1:1.5:3(1cement:1.5 fine sand:3 graded brick aggregate 20 mm nominal size) and curing complete including cost of formwork in foundation and floors. (si. no. 275) 6 providing and laying in cement concrete 1:4:8 (1cement:4fine sand:8graded brick aggregate 40 mm nominal size) and curing complete including cost of formwork in foundation and floors. (si. no. 275) 7 fixing to steel or wooden chaukhats in position. ch-10 -si no. 9(11.14) (labour only) door chaukhats above 1.5 sq.m. and upto 5 sq.m. 8 fixing to steel or wooden chaukhats in position. ch-10 -si no. 9(11.14) (labour only) window chaukhats above 1.5 sq.m. and upto 5 sq.m. 9 fixing to steel or wooden chaukhats in position. ch-10 -si no. 9(11.14) (labour only) ventilator chaukhats above 1.5 sq.m. and upto 5 sq.m. 10 provinding and fixing glass panes with putty and glazing clips in steel doors, windows,clerestory windows all complete with : 4.0 mm thick panes.ch-9 -si no. new(14) 11 mild steel or iron work in heavy sizes such as built up gates record rack, roof work, gates etc. brought to required form including drilling holes revitting or welding where necessary, and also including supply of steel bolts, nuts, wastage etc. and their fixing require for proper completion of the work. ch-10 -si no. 2, (503) 12 mild steel and iron work of small size and section such as holding down woods, hold fasts tierods, grating, etc. (when not included in and over all rates) brought to required form including supply of steel and its wastage including cost of bolts, nuts if required for proper completion of work including fabrication of holes in door chaukhats and nosing. ch-10 -si no. 3, (502) 13 providing and laying vitrified floor tiles in different sizes (thickness to bespecified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.with out base concrete ch-14 -si no. 24 (11.41) same as above but for 600x600mm size. 14 repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 metres lead : ch-13 -si no. 18(14.1) (b) with cement mortar 1:4 (1cement: 4 coarse sand) 15 12 mm cement plaster 1:4 (1 cement and 4 finesand) in single coat on fair side of single or half brick wall for interior plastering upto floor two level including internal rounded angels chamfers, and/or rounded angles not exceeding 80 mm. in girth and finished even and smooth. no extra for mixing any additive. (ch. 13 item no. 13.4 newly surface. 16 finishing walls with one coat of waterproof cement paint of approved quality on previously old treated surface with this paint to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powder material including curing and cost of all materials. ch. 15 item no. 19.29 17 finishing walls with one coat of waterproof cement paint of approved quality on previously old treated surface with this paint to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powder material including curing and cost of all materials. ch. 15 item no.662 18 providing & applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. ch. 15 item no. 31-new 19 one priming coat & two coat oil distemper on new work including supply of all materials, labour, t&p etc. required for proper completion of work. paint to be used should confirm isi no. 103-1950. (si. no. 9+10-682) chapter -16 20 painting 1st coat over priming coat (but excluding cost of priming coat) on steel and other metal surfaces upto 10cm width or girth or small articles not exceeding 0.10 sq.m. in area with superior synthetic enamel such as luxol 3, hi gloss apcolite, superlac, dulux specified brushing to give and even shade and including the cleaning the surface of all dirt, dust and other foreign matter sand papering and scrapping including cost of all materials, labour, tools and plants etc. required for proper completion of work.( ch-15 ,2-19.29 +3-642) 21 painting 1st coat over priming coat (but excluding cost of priming coat) on steel and other metal surfaces upto 10cm width or girth or small articles not exceeding 0.10 sq.m. in area with superior synthetic enamel such as luxol 3, hi gloss apcolite, superlac, dulux specified brushing to give and even shade and including the cleaning the surface of all dirt, dust and other foreign matter sand papering and scrapping including cost of all materials, labour, tools and plants etc. required for proper completion of work.( ch-15 si no 3-642 ) 22 providing and fixing water closet squatting pan (indian type w.c. pan) with 100 mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:white vitreous china orissa pattern w.c. pan of size 580x440 mm with integral type foot rests. 23 providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps,32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets,cutting and making good the walls wherever require: white vitreous china wash basin size 630x450 mm with a pair of 15 mm c. p. brass pillar taps 24 supply & fixing of 11 cm (4) internal dia. pvc down pipes complete with rosehead, bends and gratings & including supply of necessary m.s. clamps 2.5cmx 3 mm1x 1/8) fixed to walls, with & includiug supply of 15cm (6) long 6 mm(1/4) dia. nails & including supply of all material labour and t&p etc. required for proper completion of the work & also including repair of plaster,pointing etc. if damaged during fixing of pipes. details of 30 length. toilet waste water 25 note - 1. cost of maintenance of road for five years will be paid as per g.o. no. 17/2024 sa-113/23-1-2024-23-1099/113/2023 date 16-01-2024 2. the departmental road roller if spare, shall be made available to the contructior at site @ rs. 2500 per day shall be made from contractors bell for idle period 3.payment of maintenance shall be made as per final execution of civil work wich may vary from the boq.

Local Bodies

TRN :49028253 | 15 May, 2025

Tender Value : 50.00 Lacs

Barmer - Rajasthan

Tender for supply of building material and equipment in gp barasan ps gudamalani-ghadla/kankar/jhajhra 2 mortar-soil/mud masala 3 lime from kali kiln for masonry work 4 cement 5 p.p.c. 6 white cement 7 fine aggregate 8 sand/gravel 9 fly ash 10 surkhi 11 stone dust (in masonry work) 12 ballast of stone/brick (for other than road work) 13 stone 40mm measured (grit broken by hand) (cut voids 1/11) 14 stone 40mm grit (broken by crusher) (cut voids 1/11) 15 stone 20mm grit (broken by crusher) 16 stone 12/10/6mm grit (broken by crusher) 17 brick ballast 18 material for road work (including 5 km lead) 19 63-40 mm stone crushed stone gravel (cut voids 1/11) 20 63-40 mm hand broken stone aggregate(cut voids 1/11) 21 90-45 mm. hand broken stone aggregate(cut voids 1/11) 22 quarry rubbish(cut voids 1/6) 23 gravel(cut voids 1/6) 24 kankar(cut voids 1/6) 25 binding material (pi 4-6)(cut voids 1/6) 26 brick (22.5 x 11 x 7.50 cm) 27 first class (i st class) 28 second class (ii class) 29 soling/ kharanja/ masonry stone 30 masonry beradda (rr) 31 masonry radda (cr) 32 kharanja soling (for flooring work upto 15cm height) 33 kharanja soling (for road/ kharanja work upto 23cm height) 34 jodhpuri type stone strips/arches/cuts (length 2-3, width 10-12,thickness 2.5-3.5) 35 stone chips (flaky material)(3-4 thick & length and width 1-2) 36 sandstone(dpc,sill,coping,lintel,tand,almirha etc) 37 upto 25mm thickness 38 upto 25-40mm thickness 39 upto 40-50mm thickness 40 upto 50-75mm thickness 41 upto 75-100mm thickness 42 upto 100-150mm thickness 43 flooring / patti pattan katla stone 44 flooring katla upto 35mm thick, min. 3 sqft or more area 45 patti pattan katla 60-75mm thickness, min. 3 sqft or more area 46 unpolished rough kota stone 47 900 sq. cm 48 upto 901 to 2300 sq. cm. 49 above 2300 sq. cm. 50 polished kota stone(one side polished) 51 upto 900 sq. cm. 52 upto 901 to 2300 sq. cm. 53 above 2300 sq. cm. 54 marble stone(makrana adanga 20mm thick) 55 upto 900 sq. cm. 56 upto 901 to 2300 sq. cm. 57 above 2300 sq. cm. 58 marble chips 59 marble powder 60 marble stone(rajnagar ii quality/local 20mm thick) 61 upto 900 sq. cm. 62 upto 901 to 2300 sq. cm. 63 above 2300 sq. cm. 64 stone frame 65 single paitaam size 100 x 75 mm. 66 double pattam size 125 x 75 mm. 67 stone plates 68 up to 1.5 m length, minimum 40mm thick 69 1.5 m to 2.40 m length, minimum 50mm thick 70 2.4 m to 3.0 m length, minimum 65mm thick 71 above 3.0 m length, minimum 75mm thick 73 glazed size-30x45 cm 74 mosaic size-40mm thick 75 vitrified size-60x60 cm 76 interlock tiles/brick/block for road work 77 cement interlocking block m-30grade, 60mm thick 78 cement interlocking block m-30grade, 80mm thick 79 cement interlocking block m-30grade, 100mm thick 80 fr pvc insulated copper conductor single core cable isi marked 81 1.50 sq. mm. 82 2.50 sq. mm. 83 0.50 sq. mm. 84 1.00 sq. mm. 85 4.00 sq. mm. 86 6.00 sq. mm. 87 local wood with fittings (for doors, windows and furniture) 88 mango 89 acacia 90 others 91 factory made doors (30mm thick, solid core single leaf) 92 structural steel 93 iron (tor steel fe 415/500 for reinforcement) 94 winding wire 18 gauge 95 iron girders 96 conical iron/ square bars/ leaf/ angle iron 97 barbed iron wire (size 12 guage wire and 12 guage strad/12 guage wire and 14 guage strad/14 guage 98 mesh 99 iron mesh (24 gauge, 14 mesh) 100 cement concrete mesh akash patal 40mm thick 101 glass 102 3mm thick glass 103 colour paint 104 enamel paint 105 distemper (water bound) 106 lime - for whitewashing (aras / kali) 107 primer (for iron / wood) 108 petroleum products 109 diesel hsd 110 movil oil 111 bitumen shalitex board (25 mm thick) 112 plain sheet 113 g.i. sheet 22 gauge (0.80 mm) 114 g.i. sheet 24 gauge (0.63 mm) 115 m.s. sheet 22 gauge (0.80 mm) 116 m.s. sheet 24 gauge (0.63 mm) 117 corrugated sheet 118 g.i. sheet 1 mm thick 119 gi sheet 22 gauge(0.80 m.m.) 120 asbestos cement sheet 6mm(2.5/2.75x1m) 121 other sheets 122 pvc sheet 1mm thick (coloured/plain) 123 green yellow literof expo sheet(183x90) 124 pipes 125 gi 15mm diameter(b class) 126 gi 20mm diameter(b class) 127 gi 25mm diameter(b class) 128 a.c. 75mm diameter 129 a.c. 100mm diameter 130 p.v.c. 90mm diameter diameter(with ring) 131 pvc 110 mm. diameter(with ring) 132 pvc 140 mm. diameter(with ring) 133 pvc 110 mm.(2.5kg/sq.cm) with coupler 134 sanitary 135 indian w.c. 136 orrisa w.c. 137 european w.c. 138 foot rest 139 porcelain urinal 430350300 mm with coupler, bracket and pvc waste pipe 140 wash-basin 450*300 mm with coupler, bracket and pvc waste pipe 141 stone beam (s.w.) pipe 100 mm. diameter, 0.6 m. long 142 c.p. pillar cock (dia 15 mm) (is mark) 143 c.p. bib cock (dia 15 mm) (is mark) 144 c.p. grating of 125 mm. diameter 145 r.c.c. np3 hum pipe with collar 146 1200 mm dia 147 1000mm dia 148 750mm dia 149 600mm dia 150 450mm dia 151 300mm dia 152 steel conduit isi marked 153 20 mm. diameter 154 25 mm dia 155 charcoal 156 p.v.c. water tank with cover (conforming to is:12701-1989) 157 13/0.20 mm twin core pvc sheathed, flat flexible copper cable 158 steel fasteners 6 mm x 75 mm 159 pvc conduit isi marked 160 25 mm diameter 161 20 mm diameter 162 junction box 163 20 mm two way 164 20 mm one way 165 25 mm two way 166 20 mm one way (pvc) 167 module gi box 168 for 3 modules 169 for 2 modules 170 module base & cover plate 171 for 2 modules 172 3 for module 173 modular switch one way, isi marked 174 sp 15/16 ampere 175 sp 5/6 ampere 176 modular socket outlet, isi marked 177 3 pin 5/6 ampere 178 6 pin 15/16 ampere 179 mcb db 180 2+ 2 way, spn, single door 181 2+4 way, spn, single door 182 2+6 way, spn, single door 183 gi pipe (medium grade) 184 15.00 mm diameter 185 40.00 mm diameter 186 copper wire 8 swg (4.00 mm dia.) (0.117 kg/m) 187 ci/ms cover plate, frame with locking arrangement attached to 188 diesel road roller 8 to 10 ton 189 truck 9 ton 190 tractor (25-40 hp) 191 tractor trolley 192 tractor water tanker capacity 4000 liter water 193 cement concrete mixer 5-7 cubic feet 194 pumping set 15 h.p . 195 niddle/plate vibrator with operator 196 camel cart/bullock cart with driver 197 grinding machine with operator (big, motor driven) 198 compressor 199 hydraulic excavater/jcb ( bucket capacity 0.4 cum) 200 dumper 201 scraper 202 shuttering of wooden plank, with installing tp along with bat and other materials on site, removing it after the prescribed period 203 installing shuttering ply along with bat and other materials on tp site, removing it after the prescribed period 204 shuttering iron plate along with bat and other materials along with tp installation at site, removal after specified period 205 water and pumping charges (filling) 206 grinding machine with operator (small, hand operated) 207 installing iron form for well (diameter 3m, height 75cm) along with tp at site, removing after specified period 208 cultivator

State Government

TRN :49029493 | 15 May, 2025

Tender Value : 32.33 Lacs

Gautam Buddha Nagar - Uttar Pradesh

Tender for construction of e-library room in village begmabad yea. wc-06 - earth work in excavation in ordinary soil in all of foundation trenches including dressing of the side and ramming of bottom.lifts up to 1.50 m including getting out theexcavated soil and disposal of surplus excavated soil as directed with in a lead of 50m. (most/a.r./yeida) 2 supplying chemical emulsion in sealed containers including delivery as specified. chlorpyriphos/ lindane emulsifiable concentrate of 20%. (dar/2.34.1/based on uppwd/sor-2020)) 3 diluting and injecting chemical emulsion for post-constructional anti-termite treatment (excluding the cost of chemical emulsion) : treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 coarse sand) to match the existing floor: with chlorpyriphos/lindane e.c. 20% with 1% concentration (dar/2.35.3.1/based on uppwd/sor-2020)) 4 2.5 cm thick damp proof course with cement and approved coarse sand 1:1½ with and including water proofing as ordered by the engineer incharge in the proportion as specified by the manufacturer including supply of all materials, labour, tools & plants etc. required for proper completion of the work and including proper curing & shutterings as necessary. (uppwd/sor-2020/361) 5 applying a coat of residual petroleum bitumen of grade of vg-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. 6 cement concrete with 4cmgauge approved stone ballast, coarse sand & cement in the proportion of 8:4:1 including supply of all material, labour, tools&plants etc required for proper completion of the work. 7 b/w with bricks of class 150 in foundation & plinth in cm 1:4 (based on up pwd sor 2020) cement mortar 1:4 ( 1cement :4coarse sand) 8 m-150 brick work in 1:4 one cement and four course sand 2.20 f.m. mortar superstructure but for walls of half brick thick including supply of all material, labour, t&p etc. required for proper completion of the work. (uppwd/sor-2020/305(a)+310a 9 m-150 brick work in 1:4 one cement and four course sand 2.20 f.m. mortar superstructure but for walls of half brick thick including supply of all material, labour, t&p etc. required for proper completion of the work. (uppwd/sor-2020/305(a)+310a 10 extra for providing and placing in position 2 nos 6mm dia. m.s. bars at every third course of half brick masonry.uppwd-sor-2020-dar-18/6.15/ 11 providing and laying in position machine batched and machine mixed design mix m-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per is: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer-in-charge. (note :- cement content considered in this item is @ 330 kg/cum. excess/ less cement used as per design mix is payable/recoverable separately). all works upto plinth level 12 providing and laying in position machine batched and machine mixed design mix m-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per is: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer-in-charge. (note :- cement content considered in this item is @ 330 kg/cum. excess/ less cement used as per design mix is payable/recoverable separately).all works above plinth level upto floor v level 13 centringand shutteringincluding strutting, propping etc. andremoval of form for : foundation footings, base of column 14 centringand shutteringincluding strutting, propping etc. andremoval of form for : lintels, beams, plinth beam, grinder 15 centringand shutteringincluding strutting, propping etc. andremoval of form for : suspended floors, roofs, landings 16 columns, pillars, piers, abutments, posts and struts. (dar/5.9.6/based on uppwd/sor-2020)) 17 edges of slabs and breaks in floors and walls:under 20 cms wide. (dar/5.9.16.1/based on uppwd/sor-2020)) 18 earth work in rough excavation , banking excavaated earth in layers not exceeding 20 cm in depth, breaking clods watering, rolling each layer with 1/2 tonnes roller or wooden or steel rammer and rolling every 3rd and top most layer with power roller of minimum 8 tonnes and dressing up in embankments for roads, flood banks, marginal banks and guide banks or filling up ground depressions, all leads as per(a.r. )for all kind of soil. 19 steel rainforcement for r.c.c. work including straightening, cutting bending, placing in position and binding all complete upto plinth level thermo-mechanically treated bars of grade fe-500d or more./cold twisted bars. (dar/5.22.6/based on uppwd/sor-2020)) 20 12mm cement plaster of mix: 1:6 (1 cement : 6 coarse sand)based on up pwd sor 2020 dar-18/13.4.2 21 6mm cement plaster of mix: 1:3 (1 cement : 3 coarse sand)based on up pwd sor 2020 dar-18/13.17 22 15mm cement plaster of mix: 1:6 (1 cement : 6 coarse sand)based on up pwd sor 2020 dar-18/13.4.2 23 finishing walls with acrylic smooth exterior paint of required shade: new work (two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm). 24 distempering with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade 25 providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.dar-18/13.26 26 painting with synthetic enemel paint of approved brand and manufacture to give an even shade: two or more coats on new work. 27 providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, (i) single socketed pipes. 110mm dia 28 providing and fixing on wall face unplasticised - pvc moulded fittings/ accessories for unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion. single tee with door 110x110x110 mm (dar/12.42.3.2/based on uppwd/sor-2020) 29 bend 87.5° 110 mm bend (dar/12.42.5.2/based on uppwd/sor-2020) 30 shoe (plain) 110 mm shoe (dar/12.42.6.2/based on uppwd/sor-2020) 31 providing and fixing unplasticised -pvc pipe clips of approved design to unplasticised - pvc rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with m.s. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm (dar/12.43.2/based on uppwd/sor-2020) 32 providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.(dar/12.44/based on uppwd/sor-2020) 33 steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.dar-18/10.25.2 34 providing and fixing water closet squatting pan (indian type w.c. pan with 100mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required white vitreous china orissa pattern w.c. pan of size 580x440mm with integral type foot rests.up pwd sor-2020-dar 18/17.1.1 35 providing and fixing wash basin with c.l. brackets, 15 mm c.p. brass pillar taps,32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required:uppwd sor-2020-dar 17.7.1 36 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge.20mm od pipes. (dar/18.8.2/based on uppwd/sor-2020) 37 25mm od pipes. (dar/18.8.3/based on uppwd/sor-2020) 38 providing and fixingbrass gate valve with c.i. wheel of approved quality (screwed end) : 25 mm nominal bore. (dar/18.17.1/based on uppwd/sor-2020) 39 32 mm nominal bore. (dar/18.17.2/based on uppwd/sor-2020) 40 providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) applying a slurry coat of neat cement using 2.75 kg/sqm. of cement admixed with water proofing compound conforming to is. 2645 and approved by engineer-in-charge over the rcc slab including adjoining walls upto 300mm height including cleaning the surface before treatment. b) laying brick bats with mortar using broken bricks/brick bats 25 mm to 115mm size with 50% of cement mortar 1:5 (1 cement: 5 coarse sand) admixed with water proofing compound conforming to is : 2645 and approved by engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to is : 2645 and approved by engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c) after two days of proper curing applying a second coat of cement slurry using 2.75kg! sqm of cement admixed with water proofing compound conforming to is : 2645 and approved by engineer-in-charge. d) finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement: 4 coarse sand) admixed with water proofing compound conforming to is: 2645 and approved by engineer-in-charge including laying glass fibre doth of approved quality in top layer of plaster and finally finishing the surface with trowe’ with neat cement suvr an making pattern ot 300x300 mm square 3mm deep. e) the whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. all above operations to be done in order and as directed and specified by the engineer-in-charge: dar18/22.7.1 41 providing and placing on terrace (at all floor levels) polyethylene water storage tank isi: 12701 marked with cover and suttable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank dar 18/ 18.48 42 making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - iii) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.(dar 2018-4.17)based on uppwd sor/2020 43 providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. size of tile 600x600mm (dar/11.41.2/based on uppwd/sor-2020)) 44 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer-in-charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (dar/8.31/based on uppwd/sor-2020)) 45 providing and fixing brass bib cock of approved quality: 15 mm nominal bore (dar/18.15.1/based on uppwd/sor-2020)) 46 providing and fixingbrass gate valve with c.i. wheel of approved quality (screwed end) : 25 mm nominal bore. (dar/18.17.1/based on uppwd/sor-2020) 47 providing and fixing nahani trap 75x100mmincluding all complete. 48 20 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand-dar-18/13.6.1/p-902 49 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30mm thick including isi marked stainless steel butt hinges with necessary screws. (dar/9.21.2/based on uppwd/sor-2020)) 50 extra for providing isi marked stainless steel butt hinges instead of m.s. pressed butt hinges bright finished of required size with necessary screws. (shutter area to be measured). (dar/9.14/based on uppwd/sor-2020)) 51 renewing panes of glass in door, window & ventilators or fixing in the new work with 3mm thick glass panes fixed with brads & putty includung supply of all material , labour , tools & plants required for proper completion of workuppwd sor 2020/p26/806 52 prroviding and fixing isi mark 3 layer prelaminated particle board conforming to grade 2 type-iii of is-12823/20b laminated with 0.6-0.8 mm thick laminate conforming to is-2046/1995 and balancing lamination of 0.5 mm thick on the back side (size 700750430) including all complete 53 supply of work sb collection office/visitor chain with sheat dxwxh 400400450 mm padded with polyurithane foam complete 54 supply wook at site sb collection executive table of 3 layer prelaminated particle board (wood product) of grade 2 type 2 of is-12823/latest 1830 mm 950 mm 750mm including all complete 55 supplying and filling in plinth with jamuna sand under floors, including watering, ramming, consolidating and dressing complete. dar-18/2.27 56 providing and fixing factory made isi marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as f7d, f4b, k11 b and k12 b etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment).fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of c.c. 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 57 constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast r.c.c. horizontal grating with frame complete as per standard design with common burnt clay f.p.s. (non modular) bricks of class designation 7.5.(dar/18.33.1/based on uppwd/sor-2020) 58 providing, laying and jointing glazed stoneware pipes class sp-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : (dar/19.1.1/based on uppwd/sor-2020) 59 providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round s.w. pipes including bed concrete as per standard design : (dar/19.2.2/based on uppwd/sor-2020) 60 providing and fixing square-mouth s.w. gully trap class sp-1 complete withc.i. grating brick masonry chamber with water tight c.i. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: (dar/19.4.1/based on uppwd/sor-2020) 61 providing and fixing heavy class ss gratingof approved design including setting in floor with cement motor to match with floor finish as per architect requirement suitable for waster and ft, ut & fd.size 150 mm x 150 mm 62 providing and fixing ptmt towel rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.(dar/17.73.2/based on uppwd/sor-2020)) 63 providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with c.p. brass screws and washers complete. (dar/17.31/based on uppwd/sor-2020)) 64 providing and fixing ptmt soap dish holder having length of 138mm, breadth102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. (dar/18.65/based on uppwd/sor-2020)) 65 providing and fixing chicken wire mesh (murga jali) 24 gauge and 20 mesh at junction of rcc and masonry walls including fixing in position with steel nails of 25 mm in length as approved at required as directed by engineer-in-charge, scaffolding etc. complete. (ar/yeida//based on uppwd/sor-2020))½x24 gauge 66 providing and fixing aluminium hanging floor door stopper, isi marked, anodised (anodic coating not less than grade ac 10 as per is: 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.(dar/9.101.1/based on uppwd/sor-2020))single rubber stopper 67 providing and fixing aluminium tower bolts, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:250x10mm(dar/9.97.2/based on uppwd/sor-2020)) 68 providing and fixing aluminium handles,isi marked, anodised (anodic coating not less than grade ac 10 as per is: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete.125 mm (dar/9.100.1/based on uppwd/sor-2020)) 69 providing and fixing ptmt extension nipple for water tank pipe, fittings of approved quality and colour.25mm nominal bore, weighing not less than 62 gms. (dar/18.75.3/based on uppwd/sor-2020)) 70 providing & fixing of cp heavy duty bottle trap 32mm. (complete complying with relavent standard specification and as directed by the competent authority.) for wash basin&urinal 71 providing and fixing 1 mm thick m.s. sheet sliding-shutters, with frame and diagonal braces of 40x40x6 mm angle iron, 3 mm m.s. gusset plates at the junctions and corners, 25 mm dia pulley, 40x40x6 mm angle and t- iron guide at the top and bottom respectively, including applying a priming coat of approved steel primer up pwd sor-2020-dar-18/10.4 72 construction of granular sub-base by providing close graded material, mixing in mechanical mix plant at omc, carriage of mixed material to work at site, spreading uniform layers with motor grader on prepared surface and compacting with vibratory roller to achieve the desired density, complete as per clause 401 for grade-1 material. (morth/(ar/yeida/based on uppwd/sor-2020) 73 providing and laying 60mm thick i.s.i. mark factory made cement concrete interlocking concrete paver block made by block making machine with strong vibratory compaction of approved size, design, shape, laid in required colour and pattern over and including average 50mm thick compacted bed coarse sand and filling the joints with fine sand all complete as per the direction of engineer-in-charge with conforming to is-15658 and irc:sp:63. (ar/yeida/ based on uppwd/sor-2020) 74 wiring point for light in 1.5 sq. mm. pvcinsulated singlecorecopperconductor cable (inpvcconduit with 1.5sq.mm. frlsh pvc insulated multistrand copperconductor cable as earth wire drawn inside conduit.)and5 amp.flush typeswitch& ceiling rose/angle/batten holderfixedwith3mmthickphenolic laminate backalitesheet withbrass machinescrews andcup washers mounted overexisting m.s.switch boardbox/junction boxwith supplyofallmaterial, labour& t&p etc. requiredforproper completion of the work complete in all respect, as directed by engineer in charge pwd-2018 ps no-174c 75 supply and wiring of submains with 2 nos. of 2.5 sq. mm. frlsh pvc insulated1100 vgrade multistrand singlecore copper conductorcable in 25mm dia heavy duty (2mm thick) pvc conduitwith2 nos 2.5 sq.mm.frlsh pvc insulated multistrand copperconductor cable asearth continuity wire drawn in conduit complete in all respect, as directed by engineer in charge pwd-2018 ps no-261c 76 supply and fixing of power plug with 20 amp./250 voltflush type modularswitchand 5 pin 20 a/250 voltflush typeuniversal modular socket switch on concealed m.sboxincluding supply of allmaterial, labourt&petc. complete in all respect, as directed by engineer in charge .pwd-2018 ps no-1139a 77 s&f surface/flush mounting 8 ways spn distribution board with additional metal door without mcb complete in all respect, as directed by engineer in charge. pwd-2018 ps -1024a 78 s&f of 6 amp to 32 amp. mcb (10 ka) c curve complete in all respect, as directed by engineer in charge.pwd-2018ps -1002cat-a 79 s&f of 40amp. dp mcb (10 ka) c curve complete in all respect, as directed by engineer in charge. pwd-2018 ps no-1010 cat-a 80 providing and fixing circular/ hexagonal cast iron or m.s. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick m.s. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ m.s. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. clamp shall be made of 12 mm dia m.s. bar bent to shape as per standard drawing. (dar/10.18/based on uppwd/sor-2020))

State Government

TRN :49005623 | 26 May, 2025

Tender Value : 18.56 Crore

Jayal - Rajasthan

Tender for tender for widening and strengthening on kasnau (sh-92a) to dehri - tarnau - merwas - upto mataji road - 1 part a road work clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlierand disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per morth specification clause 201. by mechanical means in area of non-thorny jungle 2 excavation in soilwithdozer with lead upto 100 mexcavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 m, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections. 3 construction of embankment with material obtained from roadway cuttingconstruction of embankment with approved materials deposited at site obtained from roadway cutting and excavation from drain and foundation or other structures graded and compacted to meet requirement of tables 300-1 and 300-2 as per morth specification clause 305.3 4 construction of embankment with material obtained from borrow pitsconstruction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of tables 300-1 and 300-2 with a lead upto 50 m as per morth specification clause 305.3 5 granular sub-base with well graded material (table 400-1)by mix in place methodconstruction of granular sub-base by providing well graded material, spreading in uniform layers with tractor mount grader on prepared surface, mixing by mix in place method with rotavatorat omc, and compacting with smoothwheelroller to achieve thedesired density, complete as per morth specification clause 401. for grading iiimaterial 6 crusher run macadam baseproviding crushed run stone aggregate greading conforming to table 400-14 depositing on a prepared surface by hauling vehicles, spreading and mixing witha motor grader, watering and compacting with a threewheel 80-100 kn static roller as per morth specification clause 407 to form a layer of sub-base/base by mixing plant method with 53 mm maximum size of aggregates 7 wet mix macadamproviding, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing thematerial with water at omc in mechanical mixer (pug mill), carriage of mixed material by tipper to site, layingin uniform layers in sub-base/base course on a well prepared sub-base and compacting with smoothwheel roller of 80 to 100kn weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per tables 400-12 & 400-13 and morth specification clause 406. by mechanical means with all lead 8 prime coatproviding and applying primer coat with bitumen emulsion (ss-1) on prepared surface of granular base(wbm/wmm) including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per morth specification clause 502 9 tack coatproviding and applying tack coat with bitumen emulsion (rs-1)using emulsiondistributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with hydraulic broom as per morth specification clause 503. 10 tack coatproviding and applying tack coat with bitumen emulsion (rs-1)using emulsion distributor at the rate of 0.20 to 0.30 kg per sqm on the prepared bituminous surface cleaned with hydraulic broom as per morth specification clause 503. 11 providing and laying dense graded bituminous macadam with 100-120 tph batch type hmp producing an average output of 75 tones per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.0 to 4.5 percentby weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per morth specifications clause 505 complete in all respects. bitumen (vg-30)grading - ii (26.50 mm (nominal size)) 12 providing and laying bituminous concrete with 100-120 tph batch type hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 to 5.6per centof mix and filler,transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per morth specifications clause 507 complete in all respectsfor grading-ii(13 mm nominal size) bitumen (vg-30) 13 providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using viscosity grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kn static roller capacity, finished to required level and grades to be followed by seal coat of either type a or type b or type c as per morth specification clause 510.by mechanical means bitumen (vg-30) 14 providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using type a, type b and type c as per morth specification clause 511type b bitumen (vg-30) 15 part b c.c. pavement work dry lean cement concreteconstruction of dry lean cement concrete sub- base over a prepared sub-grade with coarse and fine aggregate conforming to is: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing. 16 construction ofun-reinforced , plain cement concrete pavement m-40 (grade), thickness as per design, over a prepared sub base, with 43/53 grade cementas per clause 602.2.2 , coarse and fine aggregates conforming to is:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a in fullyautomatic batching plant andtransported to site intransit mixer for having continous agitated mixer, manufactured as per approved mix designincluding pumping of r.m.c. from transit mixer to site of laying , with all lead and lift including cost of admixtures in recommended portion as per is 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer in charge laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using fixed form paver and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days using water finishing to lines and grade as per drawingand morth specification clause 602 including vaccum dewatering process with all required equipments (dowel bars will be paid seprately). 17 providing and fixing of dowel bars of mild steel confirming to is : 432 of specified length and diameters as per morth specification irc 15 & 58 including cutting, placing in position across transverse joint with proper spacing, providing with pvc sleeve complete as per drawing, technical specification and as per direction of the engineer-in-charge. 18 part c protection wallearthwork in excavation for structures as per drawing and morth specifications clause 304.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitablematerial. ordinary soil upto 3 m depth 19 providing concrete for plain/reinforced concrete in open foundations complete as per drawings and morth specifications clause 1702, 1703, 2102 & 2104 p.c.c grade m 10 nominal mix 1:3:6 20 stone masonry work in cement mortar in foundation complete as per drawing and morth specifications clauses 1402, 1405, 2102 & 2104. random rubble masonry in 1:6 cement mortar 21 plastering with cement mortar (1:4), 20 mm thick on stone work. 22 providing pcc m-20 architectural coping on the top of wing wall, return wall etc. complete as per drawing and morth specification clauses 1313, 1411 and 2206.650 mm thick 23 part d c.d.workearthwork in excavation for structures as per drawing and morth specifications clause 304.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitablematerial. ordinary soil upto 3 m depth 24 providing concrete for plain/reinforced concrete in open foundations complete as per drawings and morth specifications clause 1702, 1703, 2102 & 2104 p.c.c grade m 10 nominal mix 1:3:6 25 providing concrete for plain/reinforced concrete in open foundations complete as per drawings and morth specifications clause 1702, 1703, 2102 & 2104 p.c.c. grade m 20nominal mix (1:2:4) 26 providing and fixing stone slab covering over drains (kota/bijoliya quarry) having thickness 75 mm to 150 mm including filling of joints in cement mortar 1:3 with 50 mm thick cement concrete flooring in 1:2:4 mix complete with good finish as per approved drawings and specifications.for drain opeining size 300 to 450 mm stone patty drain cover size 800mm x 600mm x 75mm 27 providing concrete for plain/reinforced concrete in open foundations complete as per drawings and morth specifications clause 1702, 1703, 2102 & 2104 p.c.c grade m 10 nominal mix 1:3:6 28 providing and laying reinforced cement concrete pipe np3 as per design in single row providing and laying reinforced cement concrete pipe np3 for culverts on first class bedding of granularmaterial in single row includingfixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets clause 2905. 29 600 mmdia 30 300 mm dia 31 part f road saftykilometrestonereinforced cement concrete m15grade kilometre stone/local stone of standard design as per irc:8 fixing in position including painting and printing, etc as per drawing and morth specification clause 801 32 5th kilometre stone (precast) 33 ordinary kilometer stone (precast) 34 200 m stone (precast) 35 traffic signsretro-reflectorised traffic signsproviding and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per irc:67 made of encapsulated lens type reflective sheeting vide clause 801.3.1, fixed over aluminium sheeting, 1.5 mm thick supported on gi pipe 50 mm dia firmly fixed to the ground by means of properly designed foundation with m-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and morth specification clause 801 36 600 mm equilateral triangle 37 600 mm circular 38 600 mm x 450 mm rectangular 39 900 mm side octagon 40 direction and place identification signs upto 0.9 sqm size boardretro-reflectorised traffic signsproviding and erecting direction and place identification retro-reflectorised sign asper irc:67 made of encapsulated lens type reflective sheeting vide clause 801.3.1. fixed over aluminium sheeting, 2 mm thickwith areanot exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with m-15 grade cement concrete 450 x 450 x 600 mm, 600 mm below ground level as per approved drawing and morth specification clause 801. direction and place identification signs upto 0.9 sqm size board 41 direction and place identification signs with size more than 0.9 sqm size boardretro-reflectorised traffic signsproviding and erecting direction and place identification retro-reflectorised sign as per irc:67 made of encapsulated lens type reflective sheeting vide clause 801.3.1, fixed over aluminium sheeting, 2 mm thickwith areaexceeding 0.9 sqm supported on dia gi pipe firmly fixed to the ground by means of properly designed foundation with m-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and morth specification clause 801 42 marking centre line and stop lines etc. on road as per irc pattern with thermoplastic paint of approved quality and make with 8% glass beads laid on the road surface at temperature 160 c with a special applicator machine complete with a special applicator machine complete with labour material and traffic diversion arrangements. 43 supplying and fixing of cat’s eye made of aluminium alloy size 75x100x22 mm having 21 biconvex lenses embedded in circular disk of abs plastic on each side. 44 providing and fixing mukhya mantri sadak yojana/ mahatma gandhi rajya sadak yojana informatory sign board with logo for roads funded by state road fund having m.s. definition plate of 1.60 mm thickness frame to steel hollow dsection of 75mm x 75mm, 2.5m long stove enamelled paint with hold fast including paint logo as per approved design and colours. the logo shall be made out of 1.6mm thick circular plate duly framed with ms angle 25x25x5 mm on back and fix on 1200mm x 150mm rectangular steel base plate 1.6mm thick, the base of circular shall be plain at the junction of base plate. the size of definition plate shall be 1500x600mm and embedding the posts by m-15 cement concrete block45 cm x 45 cm x 60 cm, 60 cm below ground levelincluding lettering / writing and painting etc. complete in all respect.as per morth specification clause 801. 45 supply of swiss type of hazard marker, made out of 2 mm thick m.s. sheet size of box is 15x15 cm with hold fast at bottom, the body is painted in orange stoving enamel paint with white/high intensity grade micro-prismatic type sheeting, on all four side.

Boards / Undertakings / PSU

TRN :48996540 | 13 May, 2025

Tender Value : 1.47 Crore

Matunga - Maharashtra

Tender for repair, renovation, and reconfiguration of lab 1 at the computer engineering and it engineering department, first floor, vjti, matunga, mumbai.= 1 dismantling of existing partitions, wall paneling, etc., all complete as per site requirements, and stacking the usable materials within building premises as directed by the architect/consultant/ engineer-in- charge, etc. complete. (lead upto 100 meters) 2 removal of cement tiles, existing flooring, wall tiles,marble, polished shahabad flooring, dado with or without bed concrete, including stacking the materials as directed, with all leads, lifts, etc., complete. (lead upto 100 meters) 3 dismantling brick masonry in lime or cement mortar and stacking the materials as directed with all leads, lifts etc. complete. ( lead upto 100 meters) 4 scraping the old paint from the plastered internal surface using a dust-free vacuum paint scraper, followed by coating the entire surface with a mixture of whiting or glue and linseed oil, including the provision of scaffolding, as directed. (the scraping of old paint should be done until the neeru finish of the plaster is achieved.) lead and lift upto 100 meters etc. complete. 5 removing old paint from steel and other metal surfaces and making the surfaces even with hand scrapping, scaffolding etc. complete. 6 removing the existing cement plaster of any thickness without causing dust nuisance, stacking the debris up to a distance of 100 meters, cleaning the site, etc. complete. 7 providing and applying an anti-corrosive chemical to exposed reinforcement of r.c.c. members such as beams, columns, and slabs. this includes one coat of alkaline rust converter (feovert, rusticide, or equivalent) after cleaning the surface with a wire brush, followed by two coats of anti-corrosive, epoxy-based, two-component, zinc-rich primer (materemaco p 130 of basf, phenolic ipnet rb, polyalk flxoprime, or equivalent) for rebar protection on exposed reinforcement. additionally, apply a concrete-penetrating corrosive inhibitor (epco kp-100, polalk ep 113, masterseal 1414 of basf, fosroc, or equivalent) over the adjoining concrete surface. etc. complete. 8 providing and applying a bond coat of approved epoxy resin (masterbrace 1414 of basf, epi bond of krishna conchem, or equivalent) before polymer plaster or concrete to ensure a perfect bond between old concrete and new concrete/polymer plaster surfaces. the bond coat should be applied within half an hour after preparation, conforming to astm c881 type 2. this process includes the use of nylon brushes, scaffolding, labor, etc. complete. 9 providing and applying ready-mix polymer-modified cement mortar with an average thickness of 15mm, using polymer in one or more layers, in a proportion of 1:5:15 (polymer, cement, and quartz sand) as per the manufacturers specifications. the surface should be cured after 72 hours of application using wet gunny bags, etc. complete. 10 providing and applying ready-mix polymer-modified cement mortar with an average thickness of 30mm-50mm, using polymer in one or more layers, in a proportion of 1:5:15 (polymer, cement, and quartz sand) as per the manufacturers specifications. the surface should be cured after 72 hours of application using wet gunny bags, etc. complete. 11 providing and applying a 30mm thick self-curing ceramic polymer microconcrete of an approved make, having a compressive strength above m30, non-shrink, and impermeable, as a filling mortar for load-carrying r.c.c. members in two layers on cleaned concrete surfaces, including honeycomb areas (using manual or mechanical means). the mortar shall be prepared by mixing nicosil c80 and fresh 53-grade cement with the required water-cement ratio to achieve the desired consistency. the application and finishing shall be done by manual trowelling. curing shall be carried out after the initial setting time, in accordance with the manufacturers specifications. the work shall be executed in line with the specifications and as directed by the engineer-in-charge. the work must be carried out by a certified applicator, and the work shall be guaranteed for 5 years. the guarantee shall be provided on a rs. 500/- stamp paper. (the bond coat, as per item no. 08 in the boq, is to be applied before the coating.) 12 providing and applying 12mm thick internal/external ready-mix plaster conforming to is: 4031 (part-4) 1988 and is: 383-1970, in a single coat using cement mortar in a proportion of 1:4, with a special type of polymer additive (approximately 0.4%), on all types of surfaces in all positions, including scaffolding and curing. the plaster shall be followed by a smooth finishing coat of gypsum plaster of 6mm thickness, ensuring an even, smooth surface suitable for painting. complete with necessary curing, scaffolding, and all other related works. 13 providing and applying a priming coat over new/old steel and other metal surfaces, including preparing the surface by thoroughly cleaning oil, grease, dirt, and other foreign matter. the surface shall be scoured with wire brushes, fine steel wool, scrapers, and sandpaper, with scaffolding as required, etc. complete. 14 providing and applying priming coat over new wood and wood-based surfaces, including preparing the surface by thoroughly cleaning oil, grease, dirt, and other foreign matter, sanding, knotting, scaffolding, etc., complete. (brands such as asian paints, dulux paints, nerolac, berger, royal, or equivalent make.) 15 providing and applying two coats of synthetic enamel paint of approved color to new/old structural steel work and woodwork in buildings, including scaffolding if necessary, cleaning, and preparing the surface (excluding primer coat). etc. complete.(brands such as asian paints, dulux paints, nerolac, berger, royal, or equivalent make.) 16 removing and refixingof doors and windows with frames and stacking the materials as directed, including all leads, lifts, labour, fitting etc., complete. (lead up to 100 meters) 17 providing and laying in pattern 600 mm x 600 mm vitrified tile flooring of 8 to 10 mm thickness and confirming to is 15622-2006 ( group bla) of approved make,quality, shade and pattern for flooring . the tile flooring shall be laid in pattern with 2 mm spacers & tiles fixed in cement mortar of 1:4. the rate shall be including floor chipping to attaining required levels, epoxy grouting of joints using approved matching colour tile grout of epoxy grout, necessary protection of the laid floor, acid wash cleaning for any stains before handover. etc. complete as per the drawing, specification and to complete satisfaction of the engineer. rate to include the wastages as per the pattern indicated in the layouts. brands like kajaria, johnson or similar etc. groove shall be filled with grout of approved shade ( brands like laticrete etc.) as dicectedby the engineer-in-charge. etc. complete. basic rate for tile material- rs. 1440/- per sq.m. 18 providing and fixing skirting, including labor, materials, and all related work, etc., complete. rate for skirting of height up to 150 mm. 19 vinyl flooring for hod cabin:providing and fixing approved color homogeneous flooring, 4mm thick with interlocking system, single-layered flexible spc vinyl flooring (spica by tusker vinyl floorings) in roll form, over the provided i.p.s. or kota stone flooring. the flooring will be fixed using approved adhesive, and all joints will be soldered with pvc rods as per the manufacturer’s specifications. the work will be completed as directed, ensuring proper leveling and cleaning. the roll width will be a minimum of 2.0 meters, and the weight of the pvc flooring will be 90 kg per 30 sqm. as directed and approved by engineer in charge. etc complete. basic rate for vinayl flooring material- rs. 900/- per sq.m. 20 providing and laying vitrified mirror/glossy/matte finish tiles of size 590 mm to 605 mm x 590 mm to 605 mm with a thickness of 8 to 10 mm, conforming to is 15622:2006 (group b1a) from an approved make, shade, and pattern, for dado and skirting in the required positions. the tiles shall be fixed in 1:4 cement mortar, including neat cement float, filling of joints, curing, cleaning, and all related work, etc., complete. basic rate for tile material- rs. 790/- per sq.m. 21 providing second-class burnt brick masonry with conventional/i.s. type bricks in cement mortar 1:6 in the superstructure, including striking joints, raking out joints, watering, scaffolding, and all related work, etc., complete. 22 lowering the debris obtained from breaking and removing cement plaster/burnt brick masonry from the first floor by any means, without causing dust nuisance or damage to the structure. the debris shall be stacked as directed by the engineer-in-charge, including cleaning the site, etc., complete. (lead up to 100 meters.) 23 removing and disposing of debris from the site to a dumping ground outside the vjti premises (in accordance with municipal rules), etc. complete. as directed by the engineer-in-charge. (minimum 6 cu.m debris per trip) 24 providing anti-termite treatment to the wooden frames of doors and windows of the existing building as per i.s. 6313 (part-iii), by drilling 6 mm dia. holes at the four corners on one side and the four corners on the other side, at a downward angle of approximately 45 degrees at the junction of the woodwork and masonry. injecting 150 ml of chlorodane 5% w.c. into each hole and sealing with putty, etc., complete, with a 2-year guarantee on bond paper. 25 providing and applying waterproof melamine polish of the required finish to the woodwork by spray machine, including knotting and preparing an even surface by scraping, applying french polish, scaffolding if required, etc., complete.note: the work is to be executed only with prior approval from the superintending engineer. (brands such as asian paints, mrf melamine or equivalent.) etc. complete. 26 providing and fixing ss t/u/l strip profiles for walls, ceilings, tiles, flooring, main doors, interior decoration, bathrooms, and living rooms, including transportation, wastage, labor, etc., complete.shape: t/u/l profilematerial: ss 304 grade stainless steeldimensions: 8 mm to 12 mmlength: 2440 mm (8 feet), 3048 mm (10 feet)type: t-sectionfinish: polishedposition: interiorcolor options: gold, rose gold, black, silver, champagne, antique hairline, antique copperthickness: 2 mm to 8 mmnote: the shape, pattern, color, and design will be directed by the architect/consultant/or engineer in charge. basic rate for material- rs. 850/- per number. 27 providing and fixing ss t/u/l strip profiles for walls, ceilings, tiles, flooring, main doors, interior decoration, bathrooms, and living rooms, including transportation, wastage, labor, etc., complete.shape: t/u/l profilematerial: ss 304 grade stainless steeldimensions: 16 mm to 32 mmlength: 2440 mm (8 feet), 3048 mm (10 feet)type: t-sectionfinish: polishedposition: interiorcolor options: gold, rose gold, black, silver, champagne, antique hairline, antique copperthickness: 2 mm to 8 mmnote: the shape, pattern, color, and design will be directed by the architect/consultant/or engineer in charge. basic rate for material- rs. 850/- per number. 28 providing and fixing sign boards foor doors:specification for waterproof signage boards (12 x 4 inch)size: 12 inches (l) x 4 inches (h) (with size tolerance is plus or minus 1%)material: high-quality, durable acrylic or pvc boardfinish: glossy or matte finish for clear readabilitywaterproof: weather-resistant, suitable for both indoor and outdoor usedesign: custom text, graphics, or logo engraving/printingmounting: wall-mountable with adhesive backing or screw mountscolors: available in multiple colors with contrast for visibility (e.g., white, black, silver)application: ideal for office cabins, rooms, labs, and other signage needsthis durable, waterproof signboard ensures clear and professional signage in various environments. including wastage, etc. complete. basic rate for material- rs. 460/- per number. 29 providing and fixing of 3d wall panels that can be painted as well.size of each panel: 2 x 2 feet.colour: any color, design, or pattern.features: lightweight, fire-resistant, easily diy, 100% recycled.made from natural bamboo plant fiber, etc., complete. basic rate for material- rs. 450/- per number. 30 providing and fixing wooden decorative fluted wall panels/louvered wall panels:material: high-quality wood (mdf, plywood, or hardwood) with a decorative veneer finish.dimensions: 8 feet x 4-5 inchesthickness: 8 mm - 12 mmdesign: fluted design with vertical or horizontal grooves for a decorative effect.color: multicolor/any colour. (customizable to match interior themes).shape: rectangular panels for seamless installation, etc., complete. basic rate for material- rs. 850/- per number. 31 providing and fixing machine cut mirror polished 16 mm to 20 mm thick telephone black / amba white / cat bary brown / rbi red / ocean brown granite stone partition with rounding the edges etc. complete. one side polishbasic rate for granite material- rs. 2530/- per sq.m. 32 providing and fixing oval-type under-counter wash hand basin of 16-inch x 22-inch size and of special color shade, having telephonic black/colored granite of 180mm thick stone black kadappa framework, including chromium-plated coupling bottle trap. the wash basin should be of cera company or equivalent, model no. 3448, as per the detailed drawing or as directed by the engineer-in-charge, etc., complete. (counter size 1.20m x 0.60m). (brands such as jaquar,kohler or equivalent make.) basic rate for wash basin - rs. 6000/- per number. 33 providing and constructing a granite kitchen platform with the installation of a stainless steel sink (600mm x 450mm) as per the detailed drawing, including vertical polished kadappa stone supports (25 to 30mm thick) on both sides, with a kadappa top (35 to 40mm thick) and a polished granite top (16 to 20mm thick). the platform will feature granite strips at the front and both sides, with two vertical granite supports (15 cm height). the top granite will be 75 cm x 40 cm, including cutting and opening for the sink of the required size in both kadappa and granite. the platform size is 5.00 m x 0.60 m, with a height of 0.75 m, etc. complete with all required finishing. basic rate for ss sink- rs. 6000/- per number. 34 supply and installation of 600x600mm modular metal perforated grid ceiling system (cg-01)the ceiling system shall be supplied and installed as per the specifications provided in the tender document, and in accordance with the directions and approval of the engineer-in-charge. the scope includes complete installation with all necessary materials, components, and finishing to ensure proper execution etc. complete. 35 providing and installation of aluminum frame works for partition with ply on both sides and laminate finish: providing and fixing partition aluminum frame work consist of 25mm x 50mm x 1.2mm thick extruded aluminium box section framework at spacing not exceeding 600mm centre to centre both ways (horizontal and vertical). the framework shall be secured at floor structural ceiling and sill/ lintel level with 25 x 50mm x 1.2mm thick horizontal aluminium section. framework to be secured to floor / walls / columns / ceiling / beams using 75mm metal screws and dowels.acoustic infill: providing & fixing acoustic insulation of approved make to g.i./ aluminum/ ms/ wooden frame partition of 50mm thick rockwool of density 48 kg/m with blanket wrapped in rp tissue suitably affixed to partition framework using where necessary gi binding wire duct tape as indicated in the drawing.outer skin:- providing and fixing 18mm plywood of brands like greenply, century or equivalent. finished with 1 mm thick laminate of approved shade applied on plywood of brands like formice, royal touche or equivalent brand.note: rate is as per aluminum framework with both side ply and laminate. etc. complete. 36 providing and fixing of laminate cladding with ply backing:providing and fixing 12mm bwr plywood (brand: greenply, century, or equivalent), directly fixed to the column. a 1mm thickness laminate of an approved shade, applied on the plywood surface. laminate brands: formica, royal touche, or equivalent. etc complete. 37 providing and installation of glass partition (toughened glass): providing 12mm toughened fixed glass partition including all patch fittings, ensuring smooth and even flush joints between glasses, fixing the same in positions to true line and level, finishing the wall joints with clear silicon sealants, cleaning the surface and ensuring that there are no scratch marks on the glass etc. complete as per drawing and specifications, glass brands should be dorma, ozone or equivalent. 38 providing and installation of glass partition (dgu glass): double-glazed unit glass with air spacer of 6 to 16mm, 95% transparency, etc. complete as per drawing and specifications, dorma or ozone or equivalent. 39 providing and installation of 12mm thick clear toughened glass door with film as required. (d2 - 0.91 x 2.10 m) specification:hardware: door to be complete with hardware to each leaf as follows: hinges: 8 nos. ss ball bearing butt hinges. door closer: concealed door closer with hold open. lock set: dead lock as approved.door handles:900mm ht. 36mm dia d type offset handle on both sides in approved powder coating. door stop: floor mounted door stopper as approved seals: drop down floor seal as approved. security system: na note: all the metal profile sections and hardware finish should match the frame. brands like dorma or ozone or equivalent. etc. complete as per drawing and specifications. 40 providing and installation of d1 - double door two-way sliding motorized door, suitable for door openings up to 1.20 meters with a maximum door weight of 100kg (both leaves). the door offers environmental protection with a working temperature range of -20°c to +50°c and is rainproof. it has a standard opening time of 3-8 seconds, with a remote control operating distance of 100 to 200 feet (depending on line of sight). the opening size is 2.4m x 2.10m, and the glass door size is 1.2m x 2.10m. brands like dorma, ozone, or equivalent, to be installed as per drawing and specifications. etc. complete. 41 providing and installation of d3 - 1.09m x 2.10m (single shutter) 12mm toughened glass door with fixed side panels, including all patch fittings, locking mechanisms, and ensuring smooth, even flush joints between the glass panels. the door is to be fixed in position to true line and level, with wall joints finished using clear silicone sealant. the surface should be cleaned and inspected to ensure there are no scratch marks on the glass. installation to be completed as per drawing and specifications, with brands like dorma, ozone, or equivalent. etc. complete. 42 pop punning: providing and applying of plaster of paris punning(1st quality isi approved pop) over plastered with minimum thickness of 8mm-12mm to existingwall surfaces, ceilings & concrete members etc., to be finished in line and plumb with smooth surface ready to receive paint base. rate to be inclusive of edge protection (gi), fibre mesh for service conduits,hacking wall surfaces for better bonding, cleaning, scrubbing the surface, providing grooves if necessary etc., complete as per architects/consultant/engineer-in-charges approval. brands like gyproc, armstrong, shera or equivalent etc. complete. 43 plastic emulsion paint (leed compliant, low voc): providing and applying plastic emulsion paint finish to walls, partitions, and ceiling surfaces of approved make, color, texture, and shade in two coats, with surface and finish acceptable to the engineer in charge to be achieved within these two coats. any additional coats, if required, shall be at the contractors cost. the work includes preparing existing surfaces by scraping away loose particles, dust, etc., washing and scrubbing, filling cracks with crack filler and binder, cleaning and making the surface dust-free, applying water-based rj london putty as directed, rubbing with sandpaper to smooth the surface, and applying one coat of primer as recommended by the approved paint manufacturer. the work also includes providing necessary scaffolding, cleaning, and protecting the site until handover, as well as masking and protecting all service devices such as switchboards, detectors, etc. the work is to be completed at all heights and leads, as per specifications or as directed by the architect/engineer in charge/consultant. brands like asian paints, berger, or equivalent are acceptable. etc. complete. 44 providing and applying premium decorative wallpaper high-end or custom designs (special finishes, custom patterns)specifications: material: non-woven fabric or vinylroll size: 21 inches wide x 33 feet long (covers 55 sq ft)pattern: various styles (floral, geometric, etc.)finish: matte, gloss, or texturedinstallation: peel & stick or pastefeatures:scratch & water-resistanteasy to clean (wipeable)fade-resistanteco-friendly, voc-freeideal for: living rooms, offices, and accent wallsmaintenance: clean with a damp cloth, no harsh chemicalscustom options: available in various colors and patterns, custom designs upon request. basic rate for wallpaper rs. 600/- per sqm. 45 standing platform (300-450 mm from ffl):construction of a standing platform at a height of 300 mm to 450 mm from the finished floor level (ffl), as per approved dimensions. the platform will be made of 18 mm thick wood (century, greenlam, or equivalent) and finished with wood polish (asian paint wood tec, mrf, or equivalent).materials:frame: mild steel or aluminum, powder-coated for corrosion resistance.surface: high-quality plywood, mdf, or approved materials with a non-slip finish.support: sturdy metal beams or supports for stability.features:height: 300 mm to 450 mm from ffl, as per design.finish: non-slip surface with smooth edges and protective coating.safety: non-slip tread and optional guardrails. etc. complete. 46 stage flooring: supply and installation of interlocking rubber tile flooring at the stage area as per the specifications and drawings provided. the flooring will consist of a 6.0 mm synthetic sport surface, including a =1.50 mm pur protect® treated vinyl surface layer, calendared and grained, supported by a pvc density single closed-cell foam, and reinforced with a fiberglass grid structure. it will feature sanosol treatment for fungistatic and bacteriostatic properties. the flooring will meet the following standards: weight: 3.7 kg/m², impact resistance (en 1517) =8 n/m, abrasion resistance (en iso 5470-1) =350 mg, shock absorption (en14808) =25% (labosport result = 28%), indentation resistance (en 1516) =0.5 mm, ball bounce (en 12235) =90%, vertical deformation (en 14809) =3.5 mm, sliding coefficient (en 13036-4) 80–110, fire (en 13501-1) cfl-s1, anti-viral activity (human coronavirus 229e) – iso 21702 (99.37% after 2 hours), energy return (nf p 90 203) =0.31 m/s, tvoc after 28 days <100 micrograms/m³ (iso 16000-6), floor score®, ce marking, en14904 compliant for multi-sports use, reach compliant, and singapore green label certified. the supply and installation will include making good any damaged surfaces using standard fillers such as birla white cement, cement-based grout, epoxy grout, or mortar, and repainting to match the color.all work will be completed in accordance with the specifications, design, drawings, and the direction of the engineer-in-charge. 47 providing and fixing of overhead storage as per the specifications and drawings provided in the tender document. etc. complete. 48 providing and fixing of surface storageas per the specifications and drawings provided in the tender document. etc. complete. 49 providing and fixing on-site a lab table as per the specifications and drawings provided in the tender document. etc. complete. 50 providing and fixing of office desk/table in faculty lounge as per the specifications and drawings provided in the tender document. etc. complete. 51 providing and fixing of office desk/table in office for hod as per the specifications and drawings provided in the tender document. etc. complete. 52 supply and installation ofhod cabin chair as per the specifications and drawings provided in the tender document. etc. complete. 53 supply and installation of faculty lounge chairs as per the specifications and drawings provided in the tender document. etc. complete. 54 supply and installation of study chairs for labs as per the specifications and drawings provided in the tender document. etc. complete. 55 supply and installation of foldable desklet tables for the seminar hall as per the specifications and drawings provided in the tender document. etc. complete. 56 removingthe exisitng light fixures, fans, wires, cables, swith boards and distribution boards etc. complete. 57 point wiring for independent plug, concealed type in min 20 mm isi marked hms pvc conduit with 1.5 sq.mm (2+1e) fr grade copper wires, modular type switch and socket, earthing and required accessories as per specification no wg-pw/sw. (brands for conduits precision/finolex/pressfit. and for cable barnds should be polycab/finolex/havells. etc. complete 58 point wiring for independent plug, concealed type in min 20 mm isi marked hms pvc conduit with 2.5 sq.mm (2+1e) fr grade copper wires, modular type switch and socket, earthing and required accessories as per specification no wg-pw/sw. (brands for conduits precision/finolex/pressfit. and for cable barnds should be polycab/finolex/havells. etc. complete 59 supplying and erecting flush type shockproof plug socket 6a & 16a (6 pin) with 16a / 25a switch combined with indicator lamp and fuse with gang box on wooden board.make /brand (roma/ legrand,/ greatwhite) etc. complete 60 supplying and erecting isi mark modular type 3 pin 6a / 16a multi socket with safety shutter, duly erected on providedplate and box with wiring connectionsetc.complete. brand : roma/gretwhite/legrand) etc. complete 61 supplying and erecting pvc surface modular double mounting plate 3 modules complete duly erected etc complete.(.brand roma/gretwhite/collar) 62 supplying and erecting pvc surface modular double mounting plate 4 modules complete duly erected etc complete.(.brand roma/gretwhite/collar) etc. complete 63 supplying and erecting pvc surface modular double mounting plate 6 modules complete duly erected etc complete.(.brand roma/gretwhite/collar) etc. complete 64 supplying and erecting pvc surface modular double mounting plate 8 modules complete duly erected etc complete.(.brand roma/gretwhite/collar) etc. complete 65 supplying and erecting pvc surface modular double mounting plate 12 modules complete duly erected etc complete.(.brand roma/gretwhite/collar) etc. complete 66 supplying and erecting regular/ standard model ceiling fan of 1400mm with sweep complete erected in position as per specification no. fg-fn/cf brand /orient/polycab/crompton etc. complete 67 supplying and erecting flush-type ceiling fan regulators and electronic step regulators for ceiling fans (600mm, 900mm, 1200mm, and 1400mm sweep), complete with installation on the provided switchboard. make/brand: roma, legrand, or greatwhite. 68 providing and fixing 36 watt 2x2 light fitingsupplying and erecting square shaped crca /die-cast aluminium powder coated housing led panel light (slim edge-lit) 600x600mm suitable for 36 w-40w includingmotion sensor led light with provision for plane front frame with translucent cover fixed to the housing etc.complete .brand philips/havels/wipro etc. complete 69 supplying and erecting 16 to 32 a dpmcb suitable to fix in 2 module of modular switch in provided box complete & duly concealed with necessary material and connected. (make/ brand: legrand/ schneider/ l&t/ indo asian) etc. complete 70 supplying & erecting triple pole and neutral distribution board (tpndb), 3 pole/4 pole mccb as incomer & outgoing sp mcb (24 poles) or tp mcb of 8 ways (24 poles), with door, 1.2mm thickness, surface/flush mounted, on iron/gi frame (vertical busbar type) as per specification no. sw-swr/mcbdb1 (make/ brand: legrand/ schneider/ l&t/ indo asian) etc. complete 71 providing & erecting 3 pole mccb, 415 v, 100a, rated short-circuit breaking capacity 25 ka (ics=100% of icu), adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/uv/tripalarm contact. mccb with phase barriers on both sides, insulation withstand capacity 800v, no line-load bias in provided enclosure/panel as per specification no. sw-swr/mccb (make/ brand: legrand/ schneider/ l&t/ indo asian) etc. complete 72 supplying, erecting & commissioning 4 pole rccb 63a, electromagnetic type with 30/100/300 ma sensitivity with earth leakage trip indication complete as per specification no. sw-rccb/rccb. (make/ brand: legrand/ schneider/ l&t/ indo asian) 73 supplying & erecting 2 pair telephone copper cable 0.5 mm dia. with high density polyethylene insulation, polyester taped, nylon rip cord & grey colour sheathed with fr pvc, conforming to itd specification s/ws 113c laid in provided pvc casing capping/conduit as per specification no. wg-tw etc. complete. cables brands should be polycab/finolex/havells. etc. complete 74 supplying and installing cat-6 cable suitable for networking as per specification no. wg-coc/nc. cables brands should be polycab/finolex/havells. etc. complete. 75 supplying & erecting mains with 2 x 2.5 sq.mm. and earth wire 1.5 sq.mm frlsh pvc copper wire in hms pvc conduit min. 20mm dia. as per specification no: wg-ma/pc.etc complete. brand :polycab/finolex/havels) etc. complete 76 supplying, erecting & terminating xlpe armoured cable 3 core 4 sq. mm. copper conductor continuous 5.48 sq. mm. (12 swg) g.i. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no.cb-lt/cu(brand: polycab/ finolex/ havells)note - the quantity of wires for looping the required number of air conditioning units has to be calculated by the contractor with respect to the provided architectural working drawing. etc. complete 77 providing & erecting hot dipped galvanised cover suitable for perforated type cable tray manufactured from 18 swg (1.2 mm thick) gi sheet of 150 mm width & 20 mm height complete with necessary hardware. cable tray brands should be profab or equivalent. etc. complete 78 supplying and erecting pvc box trunking of size 100x50 mm. with accessories on wall/ceiling as per specification no: wg-ma/box. etc. complete (make/ brand: legrand/ schneider/ l&t) 79 supply & fixing of aluminum box section to be laid on the floor with all excavation, re-cementing & refinishing civil works to make good in line with the existing floor level respective junctionbox to be fabricated in 16 swg gi sheet with cut out as required for terminating the box sections. shall include pvc conduits from jb to work station powerpoints i)150 x 150x 50 mmgijunction box with cover & cut outs etc. complete. (make/ brand: legrand/ schneider/ l&t) 80 supply of a.c split unit (2 ton) :supply of ac split unit as per the specifications, and drawings provided in tender document. make (carrier/ voltas/ bluestar/ samsung) etc. complete 81 supply of 2 ton casatte ac:2 ton inverter casette ac. cooling capacity 3200-8000 watt. offers uniform 360 degree round airflow, with 4 star energy rating. etc. complete. make (carrier/ voltas/ bluestar/ samsung) etc. complete 82 installation of 2 ton ac split unit etc. complete 83 installation of 2 ton ac cassette unit etc. complete 84 supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with rohs compliant suitable for refrigerant having 22swg thickness and inner dia/size 22mm complete. etc. complete. material selection should be high quality and from reputed brand as directed by engineer in charge. 85 supply & installation electrical communication cable between indoor to outdoor units.cables brands should be polycab/finolex/havells. etc. complete. 86 providing and fixing in position ms frame stand for a.c. units, floor or wall mounted, with vibration isolation pads and frame to be made out of required ms sections strong enough to hold the weight of the ac unit,and should be lockable, including fixing in position using necessary scaffolding, ladder etc, and painting with two or more coats ofapproved enamel paint on a coat of red oxide etc. complete 87 insulated condensate water drain piping constructed out of pvc / hdpe hard pipeswith 6mm thick nitride insulation, fitting, accessories, bends, elbows, tees, flanges, tapings, wall sleeves, hangers, supports, anchors fasteners and concealed in brickwork or flooring. etc. complete(make: finolex/ astral/ prince) 88 supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided pc / copper pipes having 9 mm thickness and inner diameter / sizes 28 mm for solar water heater/ac system. etc. complete. material selection should be high quality and from reputed brand as directed by engineer in charge. 89 supplying & erecting crca sheet metal enclosures of 1.2mm thickness with 20a, 2 pin plug & earth socket and 20a, 3 pin plug top with 20a/30a single pole mcb having rated short - circuit breaking capacity (icn) 10ka complete erected on angle iron/ gi frame. etc. complete 90 carrying out core cutting of size 3 to 5 dia x 15 length in the c.c./rock/stone wall with the help of specialized core cutting machine in proper manner and finishing the site as original. etc. complete 91 supply and installation of roller blindsas per the specifications and drawings provided in the tender document. etc. complete. basic cost for blind cloth fabric material rs.900/- per sq.m. 92 carrying out test for ceramic tiles / vitrified tileswater absorption, modulus of rupture (set of 6 tiles) etc. complete. 93 carrying out test for plywood: determination of resistance to dry heat,determination of moisture content,determination of density,thickness of plywood. etc. complete. 94 carrying out test for test for glue adhesion for plywood etc. complete. 95 carrying out test for hollow / solid /aac blocksdensity test. (set of 3 blocks), compressive strength. (set of 3 blocks), water absorption test (set of 3 blocks) etc. complete. 96 providing and fixing 15 mm dia. cpvc pipe on walls, ceiling, or floor with necessary fittings, and remaking the demolished portion, etc., complete. this includes removing the existing pipeline if necessary, conveying, and stacking the same in the pwd chowky or as directed, etc., complete. (brands such as astral, finolex, prince or equivalent make.) 97 providing and fixing 20 mm dia. cpvc pipe on walls, ceiling, or floor with necessary fittings, and remaking the demolished portion, etc., complete. this includes removing the existing pipeline if necessary, conveying, and stacking the same in the pwd chowky or as directed, etc., complete. (brands such as astral, finolex, prince or equivalent make.) 98 providing and fixing 25 mm dia. cpvc pipe on walls, ceiling, or floor with necessary fittings, and remaking the demolished portion, etc., complete. this includes removing the existing pipeline if necessary, conveying, and stacking the same in the pwd chowky or as directed, etc., complete. (brands such as astral, finolex, prince or equivalent make.) 99 providing and fixing on walls/ceiling/floor 32mm dia cpvc pipe with necessary fittings, remaking good the demolished portion, etc., complete. including removing existing pipeline if necessary and conveying and stacking the same in pwd chowky or as directed, etc., complete. (brands such as astral, finolex, prince or equivalent make.) 100 providing and fixing 75 mm dia stabilizer pipe/p.v.c. soil vent/waste pipe with necessary fixtures and fittings, such as bends, tees, single junctions, slotted vent, clamps, etc., complete. 101 providing and fixing 100 mm dia stabilizer pipe/p.v.c. soil vent/waste pipe with necessary fixtures and fittings, such as bends, tees, single junctions, slotted vent, clamps, etc., complete. (brands such as astral, finolex, prince or equivalent make.) 102 providing and fixing 10 cm pvc nahani trap with grating, etc., complete. (brands such as astral, finolex, prince or equivalent make.) basic rate for nahani trap is rs. 380/- 103 providing and fixing c.p. pillar cock long neck with aerator of approed make including necessary sockets/union nut etc. complete. basic rate for pillar cock is rs. 1250/- per number 104 providing and fixing of exhaust fan 150mm crompton/havels/usha or equivalent etc. complete. basic rate for exhasut fan is rs.1000/- per number 105 providing and fixing stainless steel round napkin hanger for bathroom/towel holder for wash basin/napkin holder/bathroom (chrome) b. heavymaterial stainless steel product dimensions 17l x 5w x 19h centimetersfinish type chromeinstallation type wall-mounted shape round including fitting etc. completed.basic rate for material is rs. 320/- 106 providing and fixing premium front glass shelf - bathroom shelf/kitchen shelves wall mounted with frosted and toughen (tradition 6 x 18) chrome including fitting etc. complete. basic rate for material is rs. 650/- 107 providing and installation of 6 mm thick mirror with 6 mm thick ply backing, as per design. the mirror will be supported by stainless steel finished buttons, etc., complete. (the glass brand should be saint-gobain, borosil, or an equivalent make) basic rate for mirror is rs. 1250/- per sq.m. 108 supply and installation of nsd make smoke detectormodel:66a, certification: ce & ertl etc. complete. 109 supply and installation of nsd make heat detectormodel:66h, certification: ce & ertl etc. complete. 110 supply and installation of response indicator make: nsdmodel: p.s (mini) etc. complete. 111 supply and installation of manual call point (m.s) make nsd 112 supply and installation of 08 zone fire alarm panel make nsd(excel) etc. complete. 113 supply and installation of flasher hooter make nsdmodel no: ms17flash etc. complete. 114 supply and installation of supply & laying 1.0 sq. mm x 2 core copper armored isi cable for alarmsystem. with accessories per meter. brand/make :polycab/finolex/havellls) etc. complete. 115 supply and installation of high quality co2 fire extinguisher (6 kg)type:carbon dioxide (co2) fire extinguisher (for electrical fires and flammable liquids)capacity: 6 kgfire rating: class b (flammable liquids) class c (electrical fires)material: cylinder: steel or aluminum alloyfinish: red powder-coated for durabilityoperating pressure: 55 bardischarge time: approx. 8-10 secondsdischarge range: 3-5 feettemperature range:operating: -10°c to +60°c storage: -30°c to +60°cmounting: includes wall bracket certification: is 15683 (india) / ul/ce certified etc. complete.note: the rates for all fire safety alarm items include the complete supply, installation, commissioning, transportation, freight, and all associated costs. 116 providing architectural/ interior design services : scope of work as below:drawings preparation: 3d views, floor plans, furniture layout, electrical layout, ceiling layout, and partition layout.color scheme & material selection: guidance on colors and material choices for finishes, flooring, and furniture.quality control: ensure standards for structural, civil, electrical, fire safety, furniture work and hvac work.interior planning: optimize lab functionality and aesthetics, including furniture, partition design, and system planning (electrical, hvac, fire safety).modifications: suggest changes to designs based on site conditions and client feedback.coordination & monitoring: ensure project progress and timely completion by working closely with contractors. deputation of interior designer degree/diploma/certificate course having knowledge of autocad and 3d home or equivalent for the full period of the work. designes. monitor on-site execution, ensuring design adherence. taking joint measurements.preparing statements for extra items and excess quantities.compliance & safety: ensure adherence to safety codes and regulations. etc. complete.

State Government

TRN :48899058 | 14 May, 2025

Tender Value : 1.85 Lacs

Kolkata - West Bengal

Tender for e-tender for repairing, painting, floor cleaning ,polishing, electrical wiring & wood work of mess at bt lines, 29/1 bt road, during the year 2024-2025.= 1 estimate for repairing, painting, floor cleaning,polishing, electrical wiring & wood work of mess at bt lines, 29/1 bt road, during the year 2024-2025. 2 stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed. 3 cement concrete (1:1.5:3) with graded stone chips 5.6 mm size with hexagonal square mesh wire netting, i.r.c. fabric mesh or x.p. m. fitted and fixed after tying the existing reinforcement on concrete without distributing the same and with proper scarping and cleaning the reinforcement and disturbed concrete with wire brush etc. after applying a coat of cement including the cost of wire netting i.r.c or x. p. m. & cost of all handling and scaffolding complete as per direction of engineer-in -charge. b) 25 mm thick 4 a) applying 2 coats of bonding agent with synthetic multi functional rubber emulsion having adhesive and water proofing properties by mixing with water in proportion (1 bonding agent : 4 water : 6 cement) as per manufacturers specification [cement to be supplied by the department] 5 cleaning the concrete surface by removing dirt and debris, marking defective locations and removing loose concrete by careful stripping untill hard surface is exposed, cutting the concrete to regular shape, wire brushing the exposed surface and removing debris from site complete as per direction of the engineer - in - charge 6 plaster (to wall, floor, ceiling etc.) with sand and cement mortar including round off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/stagingwhere necessary (ground floor). [excluding cost of chipping over concrete surface](i) with 1:6 cement mortar(c) 15 mm thick plaster 7 (ii) with 1:4 cement mortar (c) 10 mm thick plaster 8 (b) rendering the surface of walls and ceiling with white cement based wall putty of approved make and brand (1.5mm thick) 9 acrylic distemperto interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturers specification) including cleaning and smoothning of surface. two coats 10 supplying best indian sheet glass panes set in putty and fitted and fixed with nails and putty complete. (in all floors for internal wall & upto 6 m height for external wall) (i) 3 mm thick (weighing 7.4 kg/sq.m) 11 dismantling all types of plain cement concrete works, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m(a) upto 150 mm. thick 12 ordinary cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant is codes. a) pakur variety 13 supplying, fitting & fixing 1st quality ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.(a) floor with sand cement mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 kg/sq.m & joint filling using white cement slurry @ 0.20kg/sq.m. (a) area of each tile upto 0.09 sq.m (i) coloured decorative 14 (b) wall with sand cement mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 kg/sq.m & joint filling using white cement slurry @ 0.20kg/sq.m. (a) area of each tile upto 0.09 sq.m (i) coloured decorative 15 (a) painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary:(a) on timber or plastered surface:with super gloss (hi-gloss)- (iv) two coats (with any shade except white) 16 labour for taking out door and window frame including shutter for repair or replacement of different parts of the frame & refixing the same including mending good all damaes complete. (concrete and brick work for mending damage will be paid separately) (a) upto area 2.5 sq.m 17 wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, iron butt hinges and m.s clamps. (the quantum should be correted upto three decimals). (c) sal : siliguri. 18 supplying, fitting and fixing m.s. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete (1:2:4) as per direction. (cost of concrete will be paid separately) (c) 40mm x 6mm, 125mm length 19 iron butt hinges of approved quality fitted and fixed with steel screws, with isi mark. (viii) 100mm. x 75mm. x 3.50mm 20 supplying,fitting & fixing of 2-track / 3-track aluminium sliding window of all aluminium sections viz. window frame (top,bottom & side frame), shutter (top, bottom, side & interlock member) made of aluminium alloy extrusions conforming to is 733-1983 & is 1285-1975, annodised conforming to is 1868-1983, fitted with all other accessories viz. pvc roller, epdm gasket, maruti lock, screws etc. including labour charges for fitting & fixing of aluminium 2-track/3-track sliding window with fixing of glass (excluding cost of glass) all complete as per architectural drawings and direction of engineer-in-charge. 10-12 micron thickness annodizing film for 2-track window: members for bottom frame @ 0.875 kg per mtr. and for top and side frame @ 0.778 kg per mtr. and for shutter bottom and top member @ 0.472 kg per mtr., style side member @ 0.493 kg per mtr. and interlock member @ 0.612 kg per mtr. [note : for estimate purpose construction wing may consider weight of 2- track aluminium window @ 5.5 kg per sq.m.and 3-track aluminium window @ 6.5 kg per sq.m] 21 polishing only of old marble or terrazo work with oxalic acid powder using 33 gms/ sq.m. by manual labour / machine where necessary. 22 supply & fixing 240 v, 6 a, 3 pin modular type plug socket (legrand/l&t) with 6a modular type switch, without plug top on 4 module gi modular type switch board with 3 module top cover plate flushed in wall incl. s&f switch board and cover plate and making necy. connections with pvc cu wire and earth continuity wire etc. (for seperate plug) 23 distribution wiring in 1.1 kv grade 2x22/0.3 (1.5 sqmm) single core stranded fr pvc insulated & unsheathed copper wire (brand approved by eic) partly in 20mm size pvc rigid conduit fr (precision make) [for horizontal run & above false ceiling portion only] and in 19mm bore, 3mm thick polythene pipe [for vertical run embedded in wall],with 1x22/0.3 (1.5 sqmm) single core stranded fr pvc insulated & unsheathed copper wire for ecc, to light/fan/call bell points with modular type switch (brand approved by eic) fixed on modular gi switch board complete with 2 no. suitable size “ph & n” copper bar with top cover plate making earthing attachment fixed on wall incl. mending good damages to original finish. [pvc rigid conduit only for horizontal run & above false ceiling and vertical run concealed](b) average run 6 mtr 24 (a) supply & fixing 240 v, 6 a, 3 pin modular type plug socket (brand approved by eic) with 6a modular type switch, without plug top on 4 module gi modular type switch board with 3 module top cover plate flushed in wall incl. s&f switch board and cover plate and making necy. connections with pvc cu wire and earth continuity wire etc. 25 supply & fixing 240 v, 3 nos. 16 a, 3 pin modular type plug socket with 3 nos. 16a modular type switch (brand approved by eic), 20a modular switch type sp mcb (c-curve) and indicator without plug top on 12 module gi modular type switch board with 12 module top cover plate flushed in wall incl. s&f switch board and cover plate and making necy.connections with pvc cu wire and earth continuity wire etc. 26 supplying,fitting and fixing approved brand 32 mm dia.p.v.c. waste pipe, with pvc coupling at one end fitted with necessary clamps.(iii) 900 mm long 27 sub total 28 gst 18% 29 lwc 1%

Central Government/Public Sector

TRN :34428579 | 16 May, 2025

Tender Value : 0

Ernakulam - Kerala

Tender for gem bids for injector nozzle assembly,o ring,gasket for injector,o ring injector,bpointspointring c20 60c7,bush viton,o ring 1d 111 x 3point5 nitrile,o ring 1d 158point5x2point5 nitrile,paper insert,ring ms 29513 126 60c7 nse 6point531,washer copper,copper washer 12x18 ,piston ring,o ring an21 nse 6point5 60c7,viton oil seal 15x30x10 ,o ring,copper washer 8x22x1point5,indicator cock assembly,o ring,silastic black rtv 732 5368,addesive super cya nopoint495,o ring,loctite 242,loctite 549,brg complete compressor end,brg complete turbine end,sealing bush,sealing bush,spare gauge glass 583,insert push,piston ring,safety ring for abb vtr251 2p t c,o ring,hylomar paste sq 32,bush,bush,main bearing for crpointshaft,bearing opppoint side to tining gear,bearing on timing gear side,normal bearing,washer,copper washer 33x39 ,copper joint,bearing large end pairs,bolt,bolt,con rod small end bush,o ring,cylinder liner honed pa6 ,chrome plated piston ring,compression ring,o ring,scraper ring,o ring d41d225 60c7 nse 6point531,inlet valve,inlet valve seat,exhaust valve,exhaust valve seat,copper washer 60x68 ,cylinder head gasket,valve guide,o ring,cyl head sleeve,o ring d8 21a7 l 12cm,safety valve assembly,screw with expanded tappet,copper washer,o ring,o ring,o ring,valve,barrel cap,anti plash piece,washer copper,copper washer 10x14 ,bush,o ring an24 nse6point5 60c7,barrel plunger assembly 23 dia grad,toothed quarnt,feed valve spring,thrust stopper,plunger spring,shim injection,push rod,injection pump roller, roller pin bar ,metafarm bush bp25 16 20x20,oil seal 25x42x8,air disributor disc,o ring,o ring,starting air valve assly,bellow expansion 74507010 ,flexible sealing joint,flexible manifold sealing joint,o ks 240 copaslip 250 gm upto 1100degc,oks 200 molykote 250 gm upto 450 deg c,flexible joint,gasket,o ring,gasket,o ring,gasket,gasket,water pipe gasket,cyclam seal,sealing ring cyclam ,o ring ann74 nse 6point5 60c7,o ring,loctite 641,o ring ms 29513 234 an 6227 60c7,bearing,ball bearing 6308,fuel feed pump assly,expansion bellow,flexible hose for priming conn lub oil ,flexible hose on inspection door,flexible hose hpointtpointwater engine inlet ,flexible hose for fuel leaks,flexible hose for hpointtpointwater,flexible hose for ht ckt venting,flexible hose for balance water return,flexible hose for sea water pump suction,flexible hose for sea water emd,flexible hose for sea water,flexible hose for fuel leaks,flexible hose for fuel return,flexible hose for fuel leaks,flexible hose for main air start pipe,flexible hose for comppoint air,flexible hose for breather,flexible hose,set of gasket for hyd motor and diversion sectpoint,set of gasket for gms moatti filt motor mh114,set of filtering elements,set of diversion elements,filter ing element for particle detecting filt,o ring for particle detecing filter,o ring for particle detecing filter,dumb bushes 25 25 du,ball joint sfg 12 uniball,uni ball joint ss12,stop ring,coupling ring,o ring ann 046 nse 6point5 60c7,ball bearing skf 6307,ball bearing skf 3206,o ring no an58 nse6point5 21a7,o ring an33,o ring an7 31b6,rocking arm assembly,internal circlip,circlip,circlip,conical spring washer m14 ,o ring,gasket,o ring an no71 nse6point5 60c7,thermostatic valve element 57 66 ,o ring,o ring,gasket punched joint ,o ring,bs ring bsb d12 nse6point51 20a8,copper washer 30x36 ,washer copper,punched flat joint gasket ,coupling pin,annular coupling spring,bearings,spring dowel pin,o ring,o ring,o ring,links,spacers,shims,bearing assembly,spring pack new ,inner star,elastic mountings tsc t140 70 d,thermostatic valve element 21 2 bocb15501 00 a,seal kit fresh water thermostatic valve for survey vessel,sealing joint,thrust flange,spring dowel pin,spring collar,spring seat,square joint,oval joint,o ring an no53 nse6point5 60,roller bearing nj 218,bush timing gear ,circlip external 90 mm,ball bearing nj 212,punched joint,

Central Government/Public Sector

TRN :34428659 | 19 May, 2025

Tender Value : 0

Ernakulam - Kerala

Tender for gem bids for o ks 240 copaslip 250 gm upto 1100degc,valve guide,o ring exhpoint valve guide 60 c7 id18x2point5,o ring ms 29513 229 60c7 nse 6531,helicoflex sealing joint,copper washer 18x22 ,joint copper,copper washer 21 x 27 ,washer copper,conical spring washer m14 ,ball,inlet valve,ring ms 29513 126 60c7 nse 6point531,starting air valve assly,gasket for glacier filter gf600 11,rocker arm bush,o ring an28 21a7 7pb496,sleeve,rubber compensator sleeve,hose,gasket ring,gasket ring,cover with gasket ring,gasket ring,gasket,bearing tpointepointcomplete,screw m6x16,disc spring,o ring dia 3 x dia 290,o ring dia 3 x dia 260,seal tape roll,special seal,filter element,ball bearing skf 6209,shim,serrated bush,o ring,mb 25x20 du bush,mb 25x30 du bush,ring ba 25x35x7 72 nbr902 simrit,joint,o ring viton an65 60 c7,joint dia 184x240xeppoint2,o ring bush,joint,couping flex mast 10011 4,thermostatic valve element 57 66 ,o ring,injector tappet,gasket,rubber compensating sleeve,flexmaster connection,flex hose,flex hose dn 8 l 1 m,flex hose dn 13 l 1 m,flex hose dn 6 l 1 m,ball bearing for lub oil filter,set of diversion element for fms01 lo,set of gaskets for lub oil filter,toothed quarnt,shim injection,push rod,gasket,gasket,o ring,glanding,o ring,rubles compens sleeves dn50 pn16 lf130,hose fuel,hose air,hose oil,hose water,flex hose dn8 l 1m,flexible hose,flexible hose,flex hose ref 4220 d 75 l 1000mm,rubber compensating sleeve dn40 pn16 lf130,rubber compensating sleeve dn80 pn16 lf130,rubber compensating sleeve dn200 pn16 lf130,rubber compensating sleeve dn150 pn16 lf130,colllar,expansion bellow dn100,set of gasket moatti fuel filter hydpoint motor,injector nozzle assemly,gasket,expansion bellow,gasket,gasket,p2 p4 by pass valve dn100,gasket,gasket pn 16 dn 100 type 01a,o ring an 77 50d7,o ring 15x204 viton 20209 ,o ring 5x589 viton 20312 ,o ring,o ring,o ring,major spare kit,elastic mount,gasket type 1 pn40 dn 80x1point5,gasket type 1 pn40 dn 40x1point5,oval gasket nd40,gasket type 1 pn40 dn50x1point5,gasket type 1 pn40 dn 65x1point5,gasket d26x1point5 thk,expansion bellow assembly nd80,flexible hose l 1m connpoint 1 8 inch m f,guide bush,sealing ring,cyclam seal assy,silastic black rtv 732 5368,rubber compensator,rubber compensator g0150 x 130 x 016 hks g nbr gr deb,rubber compensator,rubber compensator g0200 x 130 x 016 hks g nbr gr deb,bush,bush,loctite 242,loctite 549,loctite 641,bolt,bolt,hylomar paste sq 32,copper washer,exhaust valve seat,plug,spring,outside spring,collar split,screw with expanded tappet,prc glue,copper washer 8x22x1point5,spring,o ring,bpointspointring c20 60c7,gasket for injector,o ring injector,set gaskets for hyd motor mh 114a ,spring dowel pin,o ring an33 7pb 496,ball bearing skf 6212,o ring fuel feed pump idp 120x3v,flex hose dn 32 l 1 m,spring seat,roller bearing nj 218,valve rocker bridge with pin,spring,deflector,joint,expansion bellow assembly nd50,con rod brg pair ,o ring an33 7pb 496,plut,exhaust gasket,expansion bellow assembly nd40,

Related Searched Keywords : ms roller

List of ms-roller Tenders

Get ms roller Tender Alert...

Related Searched Keywords : ms roller

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us