Filters

List of end-wall Tenders

List of latest end-wall Tenders in Indian Tenders. Click on any end-wall Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for end-wall Tenders.

All-Tenders (29)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

State Government

TRN :35763340 | 10 Nov, 2025

Tender Value : 17.65 Lacs

Dausa - Rajasthan

Tender for major repair work under state budget head at govt. sss bilona kalan -demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge: in cement mortar. dismantling stone slab roofing over wooden karries and battens (dismantling karries and battens to be paid for separately) including stacking of serviceable material and disposal of unserviceable material within 50 meter lead: demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer-in-charge. 1: 3: 6 or richer mix. dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead. providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - all work up to plinth level. m10 grade nominal mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in:cement mortar 1:6 ( 1-cement : 6-sand). centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for : columns, pillars, posts and struts etc. providing and laying in position specified grade of cement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement for beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix / design mix providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. thermo-mechanically treated bars (conforming of relevent is code) kota stone slab flooring 25 mm thick over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) for area of each slab from 2001 to 5000 sq.cm : kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete for area of each slab upto 2001 sqcm grading roof for water proofing treatment with water proffing compound cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) gola providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : plaster (ceiling): 6 mm thick cement plaster to ceiling of mix 1:3 (1cement : 3-fine sand) internal plaster : plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :12mm thick. plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :20mm thick. providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete finishing walls with acrylic smooth exterior paint of required shade including all scaffolding. new work (two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm ). distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding:new work (two or more coats) over and including scrapping and priming coat with cement primer. panting on doors & windows :- painting with synthetic enamel paint of approved brand and manufacture to give an even shade : two or more coats on new work "copping : providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc up to floor five level excluding the cost of centering and shuttering. m20 grade nominal mix 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)." wiring of light point/ fan point/ exhaust fan point/ call bell point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (is:694) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) in recessed isi marked mms ( is:9537 p - iii ) vergin material pvc conduit & it's all accessories( j.b. , bends etc.) , round tiles,18 swg hot dipped galvanized modular box with earth terminal, 6 a modular switch, modular face plate with grid plate, 3 pin ceiling rose / lamp holder/ 3 pin connector , screws etc, making connections,all as per pre approved by engineer in charge, testing etc. complete as required. for specification of copper conductor, phenolic laminated sheet's & electrical/ wiring accessories refer chapter e - 04, e - 05 & e - 07 . for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . short point (up to 3 mtr.) medium point (up to 6 mtr) long point (up to 10 mtr) wiring of 3/5 pin 6 amp. light plug point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (is:694) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) in recessed isi marked mms ( is:9537 p - iii ) vergin material pvc conduit & it's all accessories( j.b. , bends etc.) , round tiles,18 swg g.i. box with earth terminal of required size, 6 a switch, 3/5 pin 6 a socket, 3.0 mm thick isi marked phenolic laminated sheet (is : 2036 - 1995), al. alloy/ cadmium plated iron screws 20 mm cup washers etc. all as per pre approved by engineer in charge, making connections, testing etc. complete as required. for specification of copper conductor, phenolic laminated sheet's & electrical/ wiring accessories refer chapter e - 04, e - 05 & e - 07. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . on board s&f following sizes (dia.) of isi marked mms ( is:9537 p - iii ) vergin material pvc conduit as per pwd specification for electrical works along with its accessories (is: 3419 ) as required in recess including cutting the wall, covering conduit and making good the same as required. all relative and latest acceptance tests reports by any nabl accredited lab for the conduit shall be submitted before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . mms (9537 p-111)pvc condute.25mm. supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked (is:694) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a ,flame retardant as per is 10810-53, better amperage rating as per vde 0298 part 4, , in existing surface or recessed pvc/ ms conduit/casing capping including all as per pre approved by engineer in charge,making connections, etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . 2 x1.5 sqmm supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked (is:694) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a ,flame retardant as per is 10810-53, better amperage rating as per vde 0298 part 4, , in existing surface or recessed pvc/ ms conduit/casing capping including all as per pre approved by engineer in charge,making connections, etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . 2 x2.5 sqmm providing & fixing of 240/415 v ac mcb with positive isolation of breaking capacity not less than 10 ka (b/ c tripping characteristic as per type of load and site requirement) 4kv impulse withstand voltage, as per pwd specification for electrical works with isi marked is 8828(1996) / conforming to iec 60898-1 2002, iec 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , ip 20 contact protection and fitted with existing distribution board/sheets, min. operation 20,000 upto 32 a rating and 10,000 upto 63 a, 5000 for 80 a rating including making connections, testing etc. as required. . oem shall have submit nabl / cpri / erda accrediated lab test reports before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr .6a to 32a rating. 50 a to 63a rating providing & fixing of ip20 smd mid power led batten type integrated light fixture made from polycarbonate /extruded aluminium powder coated housing with in built driver , power consumption of 18w/20w ,system lumen efficacy = 120 lm/watt output, internal surge protection of 2.5 kv with short & open circuit protection ,thd < 10% ,p.f.=0.95, cri >80 , life time of minimum 50000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing. 1170mm(+/-10%) led batten with min. lumen output 2200 lm providing & fixing of energy efficient /energy saving ip 20 led direct retrofit bulb in existing holder or fixture as required with system lumen efficacy =100 lm/watt output ,pf 0.95 , cri >70, minimum life time of minimum 25000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . for additional technical parameters of product/ work, refer annexure "a" attacheded with this bsr.6/7 watt providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed un-arrmoured aluminium cable confirming to is:1554 p-i / is :7098 p - i of 1.1 kv with h4- grade electrolytic aluminium conductor confirming to is 8130 of purity >99.6 %, inner / outer sheath confirming to is:5831 in existing rcc / hume / stoneware / pvc pipe/ open duct/cable trench / cable tray (with cable tie) including testing etc. as required of following size. oem must have it's own in house nabl accrediated laboratory for testing procedure as per is:10810. for additional technical parameters of product / work refer annexure 'a' attached with this bsr 6.0 sq. mm 4 core providing & fixing of bee star rated copper wounded double ball bearing capacitor start, aluminium body & metallic blade ceiling fan conforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing (i.e. isi marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . providing & fixing of isi marked (is:1258) batten/angle lamp holder with cm/l no. printed and made out from industrial grade polycarbonate or fire resistant abs material, brass terminal & captive screwsincluding making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . p & f 1.2mm thick m.s. recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side . all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure 'a' attached with this bsr providing & fixing of 240/415 v isolator as per pwd specification for electrical works with isi marked is:13947-iii/conforming to iec 60947-3, suitable for ac22a utilization catagory, 4kv impulse withstand voltage, true contact indication, red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting, minimum phase termination capacity of 35sq.mm. , label holding facility , ip 20 contact protection and fitted with existing distribution board / sheet including making connections, testing etc. as required. oem shall have submit nabl / cpri / erda accrediated lab test reports before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . 30/40 amp rating . providing & fixing of modular type 120 w step fan regulator duly isi marked (is 11037:1984 ) with cm/l no. printed made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with ip-20 rating , including all as per pre approved by engineer in charge,making connections, testing etc. as required. for additional technical parameters of product / work refer annexure 'a' attached with this bsr5 step fan regulator 2 module 360 dgree rotating p & f isi marked (is:3854) 6 amp. flush type non modular switch with cm/l no. printed and made out from industrial grade polycarbonate or fire resistant abs material including cutting hole in tile and making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . providing & fixing of of 3/5 pin 6 amp. flush type non modular socket made out from industrial grade polycarbonate or fire resistant abs material, brass terminal with porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr .

State Government

TRN :35763827 | 10 Nov, 2025

Tender Value : 2.94 Lacs

Dausa - Rajasthan

Tender for major repair work under state budget head at gups narayanpura - demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge: in cement mortar. dismantling stone slab roofing over wooden karries and battens (dismantling karries and battens to be paid for separately) including stacking of serviceable material and disposal of unserviceable material within 50 meter lead: demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer-in-charge. 1: 3: 6 or richer mix. earth work in excavation by mechanical means (hydraulic excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. all kinds of soils providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - all work up to plinth level. 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in:cement mortar 1:6 ( 1-cement : 6-sand). random rubble stone masonry with hard stone in superstructure above plinth level and upto five level above 30cm. thick walls in :cement mortar 1:6 ( 1-cement : 6-sand).cement mortar 1:6 ( 1-cement : 6-sand). centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for : columns, pillars, posts and struts etc. providing and laying in position specified grade of cement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement for beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix / design mix providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. thermo-mechanically treated bars (conforming of relevent is code) grading roof for water proofing treatment with water proffing compound cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) gola providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :20mm thick. finishing walls with acrylic smooth exterior paint of required shade including all scaffolding. new work (two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm ). "copping : providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc up to floor five level excluding the cost of centering and shuttering. m20 grade nominal mix 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)." stone kharanja : random rubble dry stone kharanja under floor. panting on doors & windows :- painting with synthetic enamel paint of approved brand and manufacture to give an even shade : two or more coats on new work p&f rigid pvc pipe (is:4985 mark) class ii(4 kg. /cm.) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant 110mm dia wiring of light point/ fan point/ exhaust fan point/ call bell point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (is:694) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) in recessed isi marked mms ( is:9537 p - iii ) vergin material pvc conduit & it's all accessories( j.b. , bends etc.) , round tiles,18 swg hot dipped galvanized modular box with earth terminal, 6 a modular switch, modular face plate with grid plate, 3 pin ceiling rose / lamp holder/ 3 pin connector , screws etc, making connections,all as per pre approved by engineer in charge, testing etc. complete as required. for specification of copper conductor, phenolic laminated sheet's & electrical/ wiring accessories refer chapter e - 04, e - 05 & e - 07 . for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . short point (up to 3 mtr.) medium point (up to 6 mtr) long point (up to 10 mtr) s&f following sizes (dia.) of isi marked mms ( is:9537 p - iii ) vergin material pvc conduit as per pwd specification for electrical works along with its accessories (is: 3419 ) as required in recess including cutting the wall, covering conduit and making good the same as required. all relative and latest acceptance tests reports by any nabl accredited lab for the conduit shall be submitted before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . mms (9537 p-111)pvc condute.25mm. supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked (is:694) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a ,flame retardant as per is 10810-53, better amperage rating as per vde 0298 part 4, , in existing surface or recessed pvc/ ms conduit/casing capping including all as per pre approved by engineer in charge,making connections, etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . 2 x1.5 sqmm providing & fixing of ip20 smd mid power led batten type integrated light fixture made from polycarbonate /extruded aluminium powder coated housing with in built driver , power consumption of 18w/20w ,system lumen efficacy = 120 lm/watt output, internal surge protection of 2.5 kv with short & open circuit protection ,thd < 10% ,p.f.=0.95, cri >80 , life time of minimum 50000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing. 1170mm(+/-10%) led batten with min. lumen output 2200 lm providing & fixing of energy efficient /energy saving ip 20 led direct retrofit bulb in existing holder or fixture as required with system lumen efficacy =100 lm/watt output ,pf 0.95 , cri >70, minimum life time of minimum 25000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . for additional technical parameters of product/ work, refer annexure "a" attacheded with this bsr.6/7 watt p & f 1.2mm thick m.s. recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side . all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure 'a' attached with this bsr

State Government

TRN :35765746 | 10 Nov, 2025

Tender Value : 4.90 Lacs

Jaipur - Rajasthan

Tender for demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge: in cement mortar. dismantling stone slab roofing over wooden karries and battens (dismantling karries and battens to be paid for separately) including stacking of serviceable material and disposal of unserviceable material within 50 meter lead: demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer-in-charge. 1: 3: 6 or richer mix. dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead. earth work in excavation by mechanical means (hydraulic excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. all kinds of soils providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - all work up to plinth level. 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - all work up to plinth level. m10 grade nominal mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). supply & stacking good soil of earth at site complete including loading unloading & transportation etc.good soil of earth filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift. random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in:cement mortar 1:6 ( 1-cement : 6-sand). centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for :columns, pillars, posts and struts etc. centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for : columns, pillars, posts and struts etc. providing and laying in position specified grade of cement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement for beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix / design mix providing and laying in position specified grade of cement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcement for walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.m20 grade nominal mix / design mix roviding m-25 grade concrete by using cement as per codal provision instead of m-20 grade design mix. providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. thermo-mechanically treated bars (conforming of relevent is code) kota stone slab flooring 25 mm thick over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) for area of each slab from 2001 to 5000 sq.cm : kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete for area of each slab upto 2001 sqcm grading roof for water proofing treatment with water proffing compound cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) gola providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :20mm thick. finishing walls with acrylic smooth exterior paint of required shade including all scaffolding. new work (two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm ). distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding:new work (two or more coats) over and including scrapping and priming coat with cement primer. "copping : providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc up to floor five level excluding the cost of centering and shuttering. m20 grade nominal mix 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)." wiring of light point/ fan point/ exhaust fan point/ call bell point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (is:694) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) in recessed isi marked mms ( is:9537 p - iii ) vergin material pvc conduit & it's all accessories( j.b. , bends etc.) , round tiles,18 swg hot dipped galvanized modular box with earth terminal, 6 a modular switch, modular face plate with grid plate, 3 pin ceiling rose / lamp holder/ 3 pin connector , screws etc, making connections,all as per pre approved by engineer in charge, testing etc. complete as required. for specification of copper conductor, phenolic laminated sheet's & electrical/ wiring accessories refer chapter e - 04, e - 05 & e - 07 . for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . short point (up to 3 mtr.) medium point (up to 6 mtr) long point (up to 10 mtr) wiring of 3/5 pin 6 amp. light plug point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (is:694) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) in recessed isi marked mms ( is:9537 p - iii ) vergin material pvc conduit & it's all accessories( j.b. , bends etc.) , round tiles,18 swg g.i. box with earth terminal of required size, 6 a switch, 3/5 pin 6 a socket, 3.0 mm thick isi marked phenolic laminated sheet (is : 2036 - 1995), al. alloy/ cadmium plated iron screws 20 mm cup washers etc. all as per pre approved by engineer in charge, making connections, testing etc. complete as required. for specification of copper conductor, phenolic laminated sheet's & electrical/ wiring accessories refer chapter e - 04, e - 05 & e - 07. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . on board s&f following sizes (dia.) of isi marked mms ( is:9537 p - iii ) vergin material pvc conduit as per pwd specification for electrical works along with its accessories (is: 3419 ) as required in recess including cutting the wall, covering conduit and making good the same as required. all relative and latest acceptance tests reports by any nabl accredited lab for the conduit shall be submitted before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . mms (9537 p-111)pvc condute.25mm. supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked (is:694) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a ,flame retardant as per is 10810-53, better amperage rating as per vde 0298 part 4, , in existing surface or recessed pvc/ ms conduit/casing capping including all as per pre approved by engineer in charge,making connections, etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . 2 x1.5 sqmm supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked (is:694) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a ,flame retardant as per is 10810-53, better amperage rating as per vde 0298 part 4, , in existing surface or recessed pvc/ ms conduit/casing capping including all as per pre approved by engineer in charge,making connections, etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . 2 x2.5 sqmm providing & fixing of ip20 smd mid power led batten type integrated light fixture made from polycarbonate /extruded aluminium powder coated housing with in built driver , power consumption of 18w/20w ,system lumen efficacy = 120 lm/watt output, internal surge protection of 2.5 kv with short & open circuit protection ,thd < 10% ,p.f.=0.95, cri >80 , life time of minimum 50000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing. 1170mm(+/-10%) led batten with min. lumen output 2200 lm providing & fixing of energy efficient /energy saving ip 20 led direct retrofit bulb in existing holder or fixture as required with system lumen efficacy =100 lm/watt output ,pf 0.95 , cri >70, minimum life time of minimum 25000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . for additional technical parameters of product/ work, refer annexure "a" attacheded with this bsr.6/7 watt providing & fixing of bee star rated copper wounded double ball bearing capacitor start, aluminium body & metallic blade ceiling fan conforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing (i.e. isi marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . providing & fixing of isi marked (is:1258) batten/angle lamp holder with cm/l no. printed and made out from industrial grade polycarbonate or fire resistant abs material, brass terminal & captive screwsincluding making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . p & f 1.2mm thick m.s. recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side . all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure 'a' attached with this bsr providing & fixing of 240/415 v isolator as per pwd specification for electrical works with isi marked is:13947-iii/conforming to iec 60947-3, suitable for ac22a utilization catagory, 4kv impulse withstand voltage, true contact indication, red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting, minimum phase termination capacity of 35sq.mm. , label holding facility , ip 20 contact protection and fitted with existing distribution board / sheet including making connections, testing etc. as required. oem shall have submit nabl / cpri / erda accrediated lab test reports before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . 30/40 amp rating . providing & fixing of modular type 120 w step fan regulator duly isi marked (is 11037:1984 ) with cm/l no. printed made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with ip-20 rating , including all as per pre approved by engineer in charge,making connections, testing etc. as required. for additional technical parameters of product / work refer annexure 'a' attached with this bsr5 step fan regulator 2 module 360 dgree rotating

State Government

TRN :35766126 | 10 Nov, 2025

Tender Value : 4.90 Lacs

Dausa - Rajasthan

Tender for demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer-in-charge: in cement mortar. dismantling stone slab roofing over wooden karries and battens (dismantling karries and battens to be paid for separately) including stacking of serviceable material and disposal of unserviceable material within 50 meter lead: demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer-in-charge. 1: 3: 6 or richer mix. random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in:cement mortar 1:6 ( 1-cement : 6-sand). centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for : columns, pillars, posts and struts etc. providing and laying in position specified grade of cement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement for beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix / design mix providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. thermo-mechanically treated bars (conforming of relevent is code) grading roof for water proofing treatment with water proffing compound cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) gola providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :20mm thick. finishing walls with acrylic smooth exterior paint of required shade including all scaffolding. new work (two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm ). distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding:new work (two or more coats) over and including scrapping and priming coat with cement primer. "copping : providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc up to floor five level excluding the cost of centering and shuttering. m20 grade nominal mix 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)." wiring of light point/ fan point/ exhaust fan point/ call bell point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (is:694) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) in recessed isi marked mms ( is:9537 p - iii ) vergin material pvc conduit & it's all accessories( j.b. , bends etc.) , round tiles,18 swg hot dipped galvanized modular box with earth terminal, 6 a modular switch, modular face plate with grid plate, 3 pin ceiling rose / lamp holder/ 3 pin connector , screws etc, making connections,all as per pre approved by engineer in charge, testing etc. complete as required. for specification of copper conductor, phenolic laminated sheet's & electrical/ wiring accessories refer chapter e - 04, e - 05 & e - 07 . for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . short point (up to 3 mtr.) medium point (up to 6 mtr) long point (up to 10 mtr) wiring of 3/5 pin 6 amp. light plug point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (is:694) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) in recessed isi marked mms ( is:9537 p - iii ) vergin material pvc conduit & it's all accessories( j.b. , bends etc.) , round tiles,18 swg g.i. box with earth terminal of required size, 6 a switch, 3/5 pin 6 a socket, 3.0 mm thick isi marked phenolic laminated sheet (is : 2036 - 1995), al. alloy/ cadmium plated iron screws 20 mm cup washers etc. all as per pre approved by engineer in charge, making connections, testing etc. complete as required. for specification of copper conductor, phenolic laminated sheet's & electrical/ wiring accessories refer chapter e - 04, e - 05 & e - 07. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . on board s&f following sizes (dia.) of isi marked mms ( is:9537 p - iii ) vergin material pvc conduit as per pwd specification for electrical works along with its accessories (is: 3419 ) as required in recess including cutting the wall, covering conduit and making good the same as required. all relative and latest acceptance tests reports by any nabl accredited lab for the conduit shall be submitted before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . mms (9537 p-111)pvc condute.25mm. supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked (is:694) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a ,flame retardant as per is 10810-53, better amperage rating as per vde 0298 part 4, , in existing surface or recessed pvc/ ms conduit/casing capping including all as per pre approved by engineer in charge,making connections, etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . 2 x1.5 sqmm supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked (is:694) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a ,flame retardant as per is 10810-53, better amperage rating as per vde 0298 part 4, , in existing surface or recessed pvc/ ms conduit/casing capping including all as per pre approved by engineer in charge,making connections, etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . 2 x2.5 sqmm providing & fixing of ip20 smd mid power led batten type integrated light fixture made from polycarbonate /extruded aluminium powder coated housing with in built driver , power consumption of 18w/20w ,system lumen efficacy = 120 lm/watt output, internal surge protection of 2.5 kv with short & open circuit protection ,thd < 10% ,p.f.=0.95, cri >80 , life time of minimum 50000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing. 1170mm(+/-10%) led batten with min. lumen output 2200 lm providing & fixing of energy efficient /energy saving ip 20 led direct retrofit bulb in existing holder or fixture as required with system lumen efficacy =100 lm/watt output ,pf 0.95 , cri >70, minimum life time of minimum 25000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . for additional technical parameters of product/ work, refer annexure "a" attacheded with this bsr.6/7 watt providing & fixing of bee star rated copper wounded double ball bearing capacitor start, aluminium body & metallic blade ceiling fan conforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing (i.e. isi marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . p & f 1.2mm thick m.s. recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side . all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure 'a' attached with this bsr providing & fixing of 240/415 v isolator as per pwd specification for electrical works with isi marked is:13947-iii/conforming to iec 60947-3, suitable for ac22a utilization catagory, 4kv impulse withstand voltage, true contact indication, red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting, minimum phase termination capacity of 35sq.mm. , label holding facility , ip 20 contact protection and fitted with existing distribution board / sheet including making connections, testing etc. as required. oem shall have submit nabl / cpri / erda accrediated lab test reports before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure "a" attached with this bsr . 30/40 amp rating . providing & fixing of modular type 120 w step fan regulator duly isi marked (is 11037:1984 ) with cm/l no. printed made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with ip-20 rating , including all as per pre approved by engineer in charge,making connections, testing etc. as required. for additional technical parameters of product / work refer annexure 'a' attached with this bsr5 step fan regulator 2 module 360 dgree rotating

Central Government/Public Sector

TRN :35767505 | 24 Nov, 2025

Tender Value : 0

Tiruchirappalli - Tamil Nadu

Tender for assembly and welding of side wall, end wall ( x end bathroom side), end wall (y end), roof assembly and door assembly of 100 bvcm wagons

Central Government/Public Sector

TRN :35769255 | 24 Nov, 2025

Tender Value : 0

Darjeeling - West Bengal

Tender for gem bids for tiles ceremic 300x300mm tiles ceremic 600x600mm cement opc 43 grad tarpauline hdpe laminated 30x20 ldpe sheet acrylic sheet 6x4x4mm acrylic sheet8x4x4mm synthetic enamel paint colour white syntheticenamel paint colour og synthetic enamel paint colourred synthetic enamel paint colour yellow syntheticenamel paint colour green synthetic enamel paint colourbrown paint brush 2 inc paint brush 4 inch pvc door self taping screw 35mm 1 point 5 inch star head screw 1inch ply wood 8 x 4 x 6mm thick ply wood 8 x 4 x 12mmthick ply wood 6 x 3 x 12mm thick ply wood 6 x 4 x 8mmthick nails 1 inch nails 2 inch nails 3 inch nails 4 inch ms binding wire door stopper ss curtain bracket cgisheet 810 x 2410 mm long 0 point 63mm thick 8 ft cgisheet 810 x 3050 mm long 0 point 63mm thick 10 ft cgisheet 810 x 3657 mm long 0 point 63mm thick 12 ft fevicol led tube light fitting 1 x 18 or 22 w 4 ft long ledtube light fitting 1 x 18w 4 feet long complete with allaccessories led bulb 9 w led bulb 12 w led securitylight 20 watt led security light 50w pvc insulatedcable 1point 5 sqmm single core copper conductor pvcinsulated cable 2 sqmm single core copper conductor cable pvc insulated unsheathed single core flexible copperconductor 1100v grade of size 2 point 5 sqmm cable pvcinsulated unsheathed twin core flexible copper conductor1100v grade of size 2 point 5 sqmm switch board with 5 or6 amp socket switch 5 amp switch 15 or 16 amp socket 5 amp socket 15 amp switch socket combination3 or 5 pin 5 or 6 amp switch socket combination 5 or 3 pin15 or 16 amp insulation tape mcb 6 amp sp mcb 20amp 240 v mcb 10 amp sp mcb 16 amps sp with box pvc exhaust fan 200mm pvc exhaust fan 250mm sweep bed switch on off switch piano switch 15 amp casing bid number gem2025b6845866 dated 01-11-2025 bid document1 90 0 0 caping 3 or 4 inch length 6 ft size, pendent holder, angleholder, change over switch 63 amp 4 pole automatic, changeover 100 amp 4 pole, cutting plier insulated 6 inchtaparia, gi pipe 20mm dia 6 mtr long, gi pipe 15 mm diamed grade, ppr pipe 15mm dia 6 mtr long, ppr socket75mm, gi tee 15mm, ppr tee 15mm, gi elbow 15mm, ppr elbow 15mm, ppr male threaded socket 20 15 mm dia, ppr female threaded socket 20 15 mm dia, ppr femalethreaded elbow 20 15 mm dia, ppr male threaded elbow20 15 mm dia, ppr male coupler 20 mm x 112, pvc l bend4 inch, ppr socket 15mm, pvc socket 100 mm, ppr union15mm, ppr union 75mm, ppr tee reducer 20 or 15mm, gi tee reducer 20 or 15mm, gi socket 15mm, gi nipple15mm 3 long, gi tank nipple 15 mm, gi end plug 15mm, pvc pipe 4 inch, towel road, rotational mouldedpolyethylene water storage tank double layer 200 ltr, rotational moulded polyethylene water storage tank doublelayer 500 ltr capacity, rotational moulded polyethylenewater storage tank double layer 1000 ltr capacity, bib cockbrass 15mm, pvc bib cock 20mm, pvc bib cock 25mm, brass bib cock 15mm, brass bib cock 20mm, cp pillar cock15mm, brass stop cock 20mm, pvc stop cock 20mm, snow white colour european wc with s or p trap concealedof size 650x405x770m with sheet cover, wash basin, waste pipe for wash basin, angle cock wash basin, vitreous china urinal pot, wastage pipe for urinal pot, gunmetal gate valve 15 mm, gun metal gate valve 25 mm, gun metal gate valve 40 mm, overhead shower withoutarm, gi reducer 20mm to 15mm, ppr pipe cutter machine, hack saw blade, iron cutting machine blades 4 inch, wood cutting blades 5 inch, tiles cutter blade, lookingmirror cum cabinet 450mm x 300mm, plastic jerricane 20ltrs, floor tile white 2 x 2, u channel, white cement, cement, sand, silicone tube, laip 6 ft, saip 2 ft, concertina coil 5 mtr, change over 100 amp, armd cable4 core 25 sqm, ss combine 15 amp, ss combine 5 amp, mcb 10 amp, mcb 16 amp, mcb 32 amp, paint brush 2inch, wall putty, paint pink, sealing compound grade a drfixit, m seal, tiles 1x1, cgi sheet 10 ft, cgi sheet 8 ft, taping screw 2 inch, pvc pipe 6 inch, sheet 6x4, tarpaulin tripal 30x30

Central Government/Public Sector

TRN :35770160 | 12 Nov, 2025

Tender Value : 0

Imphal - Manipur

Tender for gem bids for led bulb 18w 220-240 volt led bulb 9w 220-240 volt ceiling fan 1200mm sweep with electronic regulatorconforming to is switch socket combination 6 amp 240vwith gang box isi marked switch socket combination 15amp 240v with gang box isi marked pedestal fan 400mmsweep wall mounted fan 300mm sweep conforming to is socket 3 oblique 6 pin 5 obliqu 15 amp 240v isi marked exhaust fan 300mm sweep conforming to is mcbdistribution box 8 way conforming to is 13032 mcb 20amp sp 240 volts angle holder bakelite isi marked concertina coil 1050mm dia hdpe sand bags of size14inch x 36inch weight not less than 60 gms led securitylifgt fitting 20 watts security light fittings for 65w led plywood commercial bwr grade isi marked of size 8ft x 4ftx 12mm thick bib cock fancy type 15mm long nozzle cpbrass mirror for gents of size 30inchx 15inch x5mm thick pvc connection pipe 15mm dia 450mm long with both sidenut and washer jet spray teflon tape 3 oblique 8 inchwide 10 mtr roll gun metal gate valve 25mm m painingbrush 100mm standard quality cp towel rail 600mm long20mm dia with bracket bricks sub class b old size bestlocally available minimum compressive strength 75 kgoblique sqcm water absorption not more than 20percentage app water proofing membrane 3 mm thick 1mwide 10 m long long angle iron picket of size 18 mtrlength of size 2inch x2inch laip pendent holder bakelite isimarked led batten surface 4ft long 18w output 1600lumen per watt with suitable powder coated frame endcape and connector swtich piano 6 amp 240v isi marked cp cast copper alloy bib cock long body 15mm bore cpshower rose 75mm dia with swivel arm 15mm bore squareoblique round shape mcb 10 amp sp with enclosure boxmild steel mcb 32 sp 240 volts mcb 40 amp sp 240 bid number gem2025b6848455 dated 01-11-2025 bid document1 63 0 0 volts, , mcb 63 dp 240 volts, , bulk head fitting in deepdrawn anodized aluminum body, epoxy powder coated andhead resistant prismatic glass cover with specially., waterdespencer 20 ltr make voltas, vitreous china pedestalpattern water closet european type ewc inclk pvc seat andcover, nylon rope 32mm, vitreous china wash hand basinof size 550mm x 400mm, pvc insulated sheathedunarmored cable 6sqmm twin core aluminum conductor isimarked with working voltage upto 1100 volt roll of 90 mtrs, flexible cable twin twisted roll of 90 mtr 23 oblique 0.0040, conforming to is, pvc sheathed unarmored strandedcopper conductor cable of size 1sqmm conforming to isimarked 90m roll, tripple layer hdpe water storage tankcylindrical vertical with closed top 1000ltrs capacityconforming to is specification, tripple layer hdpe waterstorage tank cylindrical vertical with closed top 500ltrscapacity conforming to is specification, 1 hp motor, nonskid ceramic colored tiles of size 600mm x 600mm x 9 to10mm thick, sheated unarmored stranded copperconductor cable of size 1.5sqmm conforming to isiconductor cable to size 1.5sqmm conforming to isi marked90m roll, flood light 200 watt, ppgi profiled sheet of size10ft x 3.5ft, 0.50mm thick, mild steel corrugatedgalvanized cgi sheet 8ft x 3ft, .63mm thick isi marked, ordinary portland cement 43 grade in hdpe bags of 50 kgseach, confirming to is 269-1976, m seal 100gm, pvcsheathed unarmoured stranded copper conductor cable ofsize 2.5sqmm conforming to isi marked 90m roll, pvcsheathed unarmoured stranded copper conductor cable ofsize 4sqmm conforming to isi marked 90m roll, thinner forpaint, tarpentin oil, paining brush 75mm standard quality, painting brush 50mm standard quality, coarse sanddimapur sand conforming to is 383 to1978., coarseaggregate crushed stone 20mm graded conforming to is383 to1979, plywood commercial bwr grade isi marked ofsize 8ft 4ft x 19mm thich, cp cast copper alloy stoop cock15 mm bore, mild steel hard drawn wire mesh 50 x 50mmpitch 3mm dia of wire, weight not less that 2.20 kg per, white cement, tirpolean plastic 30 x 30, tirpolean plastic24x18, pvc swr pipe 75m dia 3m long with socket end isimarked, pvc swr pipe 110m dia 3m long with socket endisi marked, pvc l bow 4 inch, pvc t 4 inch, pvc socket 4inch, pvc l bow 3 inch, pvc t 3 inch, pcv socket 3 inch, pixel bulk head fitting in deep drawn anodized minimumbody, epoxy powder coated and heat resistant prismaticglass cover with specially, change over switch 63 amp fourpole, change over switch 100 amp four pole, 25 ltr waterstrong geyser plastic body with all accessories forinstallation, pvc insulated sheathed unarmoured cable10sqmm twin core aluminium conductor isi marked withworking voltage upto 1100 volt roll of 90 mtr, insulationtape 3 oblique 8 inch wide 9 mtr roll, mild steel wire nailssorted size, gi binding wire 3mm dia, curtain rod mscp20mm dia 12ft long, bracket for curtain rod aluminiumpowder coated curtain rod in white colour 20 oblique 25mmdia, synthetic enamel paint high gloss superiour qualityblack colour, synthetic enamel paint high gloss superiourquality red colour, synthetic enamel paint high glosssuperiour quality yellow colour, synthetic enamel painthigh gloss superiour quality og colour, synthetic enamelpaint high gloss superiour quality white colour, plywoodcommercial bwr grade isi marked of size 6ft x 3ft x 12mmthick, cp cast copper alloy pillar cock 15mm, batten holderbakelite, vitreous china urinal pot bowl type including //bid details2 / 63 spreader, solvent cement for pvc pipe, distemper paintemulsion oblique acrylic distemper, pvc flexible ribbed pipe20mm dia

Central Government / Public Sector

TRN :35745923 | 17 Nov, 2025

Tender Value : 15.71 Lacs

Jaipur - Rajasthan

Tender for gem bids for call, visit charges to attend fault of dea set general servicingof the up to 20 kva dea sets general servicing of morethan 20 kva and upto 325 kva dea sets generalservicing of more than 325 kva and up to 55 kva dea sets replacement of diesel filter element set 1 ltr replacement of oil filter element 1 by 2 ltr replacementof oil filter element 1 ltr replacement of diesel filterelement set 1 by 2 ltr replacement of oil filter setsuitable for ea set of 50 to 55 kva replacement oflubricating oil multi grade 20w40 replacement of steelwire braided fuel pipe line replacement of stop solenoid12 volt replacement of starting key with switch replacement of mechanical type rpm cum hr meter replacement of mechanical type rpm cum hr meter chain replacement of battery leads red and black replacementof coolant for radiator of superior quality replacement ofv belt replacement of hose pipe set with clips replacement of techo drive unit replacement of fuelfeed pump assembly replacement of solid state smps orscr based battery chargers replacement of push buttonswitch for start or stop or reset replacement of 12 v dcor 220 v ac hr meter counter type supply and fixing of12 volt battery operated self starter supplying and fixing of12 volt battery charging alternator repairing of 12 voltbattery charging alternator repairing and generalservicing of the existing faulty radiator up to 55 kva pdggeneral servicing and repairing of 12 volts engine startingself dismentalling of existing up to 20 kva dea sets dismentalling of existing more than 20 kva and upto 55kva dea sets extra for shifting of existing dea set up to 20kva loading of existing up to 20 kva dea sets loading ofexisting more than 20 kva and upto 55 kva dea sets transportation of up to 20 kva dea sets transportation of bid number gem2025b6823729 dated 25-10-2025 bid document1 59 0 0 more than 20 kva and upto 55 kva dea sets, unloadingup to 20 kva dea sets, unloading more than 20 kva andupto 55 kva dea, itc of up to 20 kva dea sets on existingfoundation, itc of more than 20 kva and upto 55 kva dea, labour charges for top overhauling of existing dea setsup to 20 kva, replacement of the liner assembly withrubber ring dea sets up to 20 kva, replacement of thepiston set without piston ring set dea sets up to 20 kva, replacement of the piston ring set dea sets up to 20 kva, replacement of the set of gasket including head gasketdea sets up to 20 kva, replacement of the o ring set deasets up to 20 kva, replacement of the cr bearing dea setsup to 20 kva, replacement of the main bearing dea sets upto 20 kva, replacement of the oil pressure guage dea setsup to 20 kva, replacement of the front oil seal of crankshaft dea sets up to 20 kva, replacement of the back oilseal of crank shaft dea sets up to 20 kva, repairing ofcylinder head, repairing of up to 20 kva dea sets crankshaft, transportation charges up to 50 km for alternator upto 55 kva, transportation charges more than 51 to 100 kmfor alternator up to 55 kva, rewinding of main statorwinding of alternator up to 20 kva, rewinding of main rotorwinding of alternator up to 20 kva, rewinding of mainstator winding of alternator more than 20 kva and upto 55kva, rewinding of main rotor winding of alternator morethan 20 kva and upto 55 kva, exciter stator winding ofalternator up to 55 kva, exciter rotor winding of alternatorup to 55 kva, replacement or repairing of avr, replacement or repairing of power diode for rotatingrectifier assembly, replacement or repairing of bearingsuitable for above 20 kva alternator, providing of 2 core16 sqmm, providing of 4 core 16 sqmm, laying of onenumber upto 35 sq. mm on wall surface, laying of onenumber upto 35 sq. mm direct in ground, laying of onenumber upto 35 sq. mmin the existing rcc or hume ormetal pipe, supply and making end termination for 2 x 10sq. mm 19 mm, supply and making end termination for 4 x16 sq. mm 28 mm, providing and fixing 6 swg dia g.i. wire, sitc of 32 amps four pole on load side handle operatedchange over switch, sitc of 63 amps 2 pole on load sidehandle operated change over switch, sitc of 63 amps fourpole on load side handle operated change over switch, providing and fixing 63 amp tpn disconnector fuse switchunit

Central Government And Public Sector

TRN :35749415 | 10 Nov, 2025

Tender Value : 0

Raebareli - Uttar Pradesh

Tender for supply of set of end wall for 3ph memu/dmc & memu/dmc2 coaches.

Central Government/Public Sector

TRN :35749619 | 10 Nov, 2025

Tender Value : 0

Panchkula - Haryana

Tender for gem bids for sheet bakelite , tape pvc , sheet bake , bell indication 12 way , pvc gang box , batten nails , pvc flexible , shadals various , telephone nails , plastic rawal plug , bulb 100 , false ceiling , bell cord less , bell indication , bus bar , electronic meter , fan hook , plug top 15 amp , pvc 200mm , pvc 250mm , pvc 300mm , pvc bulb holder angular type , pvc gang box 15 amp , hexa blade double ended , holder bipin rotraty , insulation tape , switch neon indicator , plywood mdf board 8x4x18mm , plywood , glass shelf , low level , pvc pipe 75mm , sink coupling 100mm , cp peg set of 06 , cp hand shower , curtain rod , pvc pipe 100mm , glass sheet frosted , waste pipe , door stopper , waste coupling , cp brass soap dish , handle aluminum 150mm , tower bolt ms 100 mm , bracket sider end doom , glass sheet clear , tower bolt , cp brass , bracket for fancy , mortice lock , aluminum hinges 100 mm , door seal 900mm long , grating cp , door seal 1200 mm long , thread for plumber , ms hinges 100mm , helical door spring , grating cp stainles , nipple hexa 15 mm , hamber drill bit , rawal plug , blade cutter iron , paper holder , m seal , washer for cistern , fevicol , ss handle , wire mesh , magnetic catcher , dr fixit , tarpentine oil , pvc ball , drip seal , angular stop cock , ms hasp and stapple , drain cover mm , drain cover , taflon tape , star bit for drill , glass shelf 600mm long , 15mm kitec elbow , 15mm kitec socket , 15mm kitec tee , 15mm kitec union , kitec connectore , electric insulation rubber mat , street light 120w , street light 90w , spot light green , spot light warm white , spot light cool white 12w , contractor 185 amp 415 v , contractor 40 amp 415 v , led recess , cable pvc 16 sqmm 1 core , cable pvc 2 point 5 sqmm 1core , cable pvc 1 point 5 sqmm 3 core , cable pvc 1 point 5 sqmm 1core , led lamp 12 watt , led lamp 9 watt , led recessed luminaire 12 watt , led surface celing , cable pvc flat , led spot light 12 , automatic star , dol starter , calling bell ding dong , insualtion tape , aluminium thimble 150 , aluminium thimble 400 , plug top 3 pin16 amp , modular fan regulator , switch board boxes 6 modular , aluminium inline , aluminium thimble , switch board boxes , cable jointing kit , aluminium inline connector 185 , modular bell push , aluminium inline connector 95 , aluminium inline connector , aluminuum thimble 95 , aluminium thimble 50 , aluminuum thimble 70 , pvc gang , aluminium thimble 35 sqmm , aluminium thimble 25 , insulation tape , batten holder 6 amp , connector 35 sqmm , inline connector , aluminium connector , junction box , bulb 100 w , industrial socket , aluminium inline 50 , pvc condute pipe 20 mm , pvc condute clamp , modular plate 3 module , modular plate 4 module , modular plate 6 module , hydraulic door closer , glass sheet , stainless steel curtain rod , glass sheet clear , copper sulphate , frame plate 6 module , aluminium door seal , nrv 150 mm , patchmat bitumen , cp brass extension nipple , hack saw blade double edge , brass nozzle 15 mm for fountain , frame plate 3 module , nrv 100 mm , hex nipple 20 mm x 50 mm , ht tape black roll of 20 mtr , brass spindle , particle board , brass nozzle , ms but hinge 100 mm , ball valve brass , hex nipple , bearing grease , magnetic door catcher , cp brass urinal , cp wall bracket l shape , insulated tape , cp end bracket , blanking plate , lime , industrial socket 63 amp , floor door closer , aluminim hasp and staple , wire clamp 10 mm , batten nail , pvc internal cistern10 ltr capacity , tank 1000 ltr , ss curtain rod , sliding bolt , cotton thread 1 pkt 60 pcs , aluminium sheet 1 mm thick , toilet seat covers (v2) (q4) , ptmt tap fitting (q3) , modular piano type domestic electrical switches as per is 3854 (q3) , piano type non modular domestic electrical sockets - is 1293 (q3) , non - modular piano type domestic electrical switches as per is 3854 (q3) , piano type modular domestic fan regulator as per is 11037 (q3)

Related Searched Keywords : end wall

List of end-wall Tenders

Tender for assembly and welding of side wall, end wall ( x end bathroom side), end wall (y end), roof assembly and door assembly of 100 bvcm wagons

Tender for supply of set of end wall for 3ph memu/dmc & memu/dmc2 coaches.

Get end wall Tender Alert...

Related Searched Keywords : end wall

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us