Filters

List of latest aggregate-materials Tenders in Indian Tenders. Click on any aggregate-materials Tenders to view BOQ, NIT and Tender Documents. Get Bidding Support and Vendor Registration for aggregate-materials Tenders.

All-Tenders (15)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

Central Government/Public Sector

TRN :19041519 | 05 Oct, 2020

Tender Value : NA

Barmer - Rajasthan

Tender for supply of super structure including columns, trusses, purlins, runners, roof with galvalume corrugated sheets with heat reflective aluminium foil sheet of make cocoon shield ® / thermal wrap® / aircell insulations mk petro products pvt ltd / divine thermal wrap pvt ltd of 10mm thick fr bubble double sided heat reflective aluminum sheet with 18 micron, thickness low emissivity 3%, wind tie, false ceiling, flush doors with pressed steel frame one or more rebates incl necessary fixing lugs, hinges, lock strike plate etc complete, aluminum window/cooler window and aluminum ventilators with flyproofing and particle board partition panel complete all as shown on drg and specified incl rcc foundation, erection tools list cement ppc/opc 53 grade make:ultratech / ambuja / acc / birla/jk laxmi sand coarse to be approved by consignee authority stone aggregate 20mm nominal size stone aggregate 40mm stone aggregate 63mm to 75mm pcc solid blocks of size 400 x 200 x 200 mm in pcc 1:2:4 brick bats water proofing compound, make : birla / acc/ ultratech vitrified tiles 600x600x10mm thick first quality make : jhonson / kazaria / samani non skid ceramic tiles first quality 300 x 300 mm x 7 to 8 mm thick for toilet block only. make : kajaria / jhonson / asian / somani glazed ceramic tiles first quality 300 x 450 mm x 7 to 8 mm thick for toilet block on vertical surface. make : kajaria / jhonson / asian / somani white cement. make : birla / jk / shree mild steel tmt bar 10mm dia for lintel make : tata/jindal/sail mild steel tmt bar 8mm dia for lintel make : tata/jindal/sail binding wire oil bound distemper make : asian / nerolac / berger / shalimar primer first quality make : asian / nerolac / berger / shalimar cement base paint make : snowcem / jhonson / asian synthetic enamel paint white first quality make : nerolac / apcolite / berger /asian / shalimar ms hook 12 mm dia rod for fan exhaust fan 200mm complete of pvc body with louvres make - bajaj / usha / khaitan / cg ceiling fan 1200mm sweep.make : bajaj /usha / crompton & greaves /khatian/ orient elecronic type regulator. make : bajaj /usha / crompton & greaves /khatian/ orient desert cooler with iron stand 3000 cfm as specified. make : bajaj/usha / khaitan. cooler body - 18 gauge, isi marked, copper coil 36w led tube light 4 complete set. make : bajaj / philips / cg 20w led tube light 2 complete set. make : bajaj / philips / cg / surya led bulb 8w with angle holder. make: bajaj/phillips/cg led bulb 14w with angle holder. make: bajaj/phillips/cg recess mounting light 2x2 with two pl tubes of 36w each including all accessories. make : bajaj / phillips / cg socket for cable tv and socket for telephone with pvc square box ie. junction terminal anchor / cg / havells and 40 mm pvc conduit isi marked including accessories and clamps etc. pipe- 20 rm with coaxial cable for tv and telephone cable 02 run for telephone incl 10 pair terminal box. switch 5 amps modular type one way. make : anchor / crabtree / indoasian /siemens / l&t. switch socket combination 15 amps 6 pin modular make : anchor / crabtree / indoasian/ siemens / l&t switch socket combination 6 amps 5 pin modular. make : anchor / crabtree / indoasian/ siemens / l&t external type 12 watt led light complete make-bajaj/philips/oreva/crompton and greeves pvc copper cable insulated, multi standard 2.5 sqmm. colour : black & red. make : anchor / havells / finolex ceiling rose make - bajaj / philips / siemens /anchor bell dingdong ac 230v single phase. make : anchor/havells/c&g bell push 6 amps modular 230v. make : anchor/crabtree/siemens/ l&t pvc block 4x4 socket 5 amps modular, 5 pin, isi marked pvc gang box with modular pvc plate of suitable size as per ground requirement as approved by consignee 2 way pvc gang box with modular pvc plate of suitable size as per ground requirement as approved by consignee 4 way pvc gang box with modular pvc plate of suitable size as per ground requirement as approved by consignee 5 way pvc gang box with modular pvc plate of suitable size as per ground requirement as approved by consignee 6 way mcb db enclosure 8 way complete sheet metal enclosures make : anchor / c&g / l&t mcb spn 40 amps make : anchor /indoasian/ philips / bajaj mcb sp 10 amps, 10 ka cseries. make : anchor /indoasian/ philips / bajaj mcb sp 16 amps, 10 ka cseries. make : anchor /indoasian/ philips / bajaj mcb sp 20 amps, 10 ka cseries. make : anchor /indoasian/ philips / bajaj mcb sp 25 amps, 10 ka cseries. make : anchor /indoasian/ philips / bajaj pvc capping / casing 25mm with accessories isi marked. make : anchor /indoasian/ philips / bajaj pvc copper cable insulated, multi stranded 1.5 sqmm. colour : black, red & green. roll of 90m each make : kei/ anchor / havells / finolex flexible wire twin twisted pvc unarmed aluminum cable 10 sqmm 2 core make : anchor/ havells/finolex earthing complete with copper plate as per specification. screw 65/25/20mm pvc insulated tape 15mm make- steel grip / faxwell hydraulic door closure as per sample approved by co engr regt. isi marked hdpe water tank 2 x 500 itrs tank as per specification incl 3.0m high staging as shown in drg. make - sintex/js polyplast/polyconfor ojl shelter

State Government

TRN :19033449 | 05 Oct, 2020

Tender Value : 3.20 Crore

Thoubal - Manipur

Tender for construction of road at mn08114 t15-haokha babu bazar to moijing construction of job pillers as per fig. 1600.1 d and technical specification clause 1602.4 surface drains in soil construction of unlined surface drains of average cross-sectional area 0.40 sqm in soil to specified lines, grades, levels and dimensions. excavated material to be used in embankment with a lift upto 3m and lead of 50 m average lead 25 m as per technical specification clause 307. a manual means construction of embankment with material obtained from borrow pits construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of tables 300.1 and 300.2 with a lead upto 1000 m as per technical specification clause 301.5 construction of subgrade and earthen shoulders construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table 300.2 with lead upto 1000 m as per technical specification clause 303.1. compacting original ground supporting subgrade loosening of the ground upto a level of 300 mm below the subgrade level, watered, graded and compacted in layers to meet requirement of tables 300.1 and 300.2 for subgrade construction as per technical specification clause 303.5.2. kilometre stone reinforced cement concrete m15 grade kilometre stone/local stone of standard design as per irc:8 fixing in position including painting and printing, etc as per drawing and technical specification clause 1703 i ordinary kilometer stone precast ii 200 m stone precast providing and fixing logo of pmgsy project providing and fixing of typical pmgsy informatory sign board with logo as per mord specifications and drawing. three ms plates of 1.6 mm thick, top and middle plate duly welded with ms flat iron 25mm x 5m size on back on edges. the lower plate will be welded with ms angle iron frame of 25mm x 25mm x 5mm. the angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 swg sheet tubes posts duly embedded in cement concrete m-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. the top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 swg steel plate tube. all m.s. will be stove enameled on both sides. lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. all sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing clause 1701 and annexure 1700.1 providing and fixing of citizen information board of pmgsy project steel tube providing and fixing of citizens information board for pmgsy project with logo as per mord specifications and drawing. two ms plates of 1.6 mm thick, top and bottom plate duly welded with ms flat iron 25mm x 5m size on back on edges. the plates will be welded with ms angle iron frame of 25mm x 25mm x 5mm. the angle iron frames of the plates will be welded to 2 nos. 75mm x 75 mm of 12 swg sheet tubes posts duly embedded in cement concrete m-15 grade blocks of 600mm x 600mm x 750mm, 750mm below ground level. all m.s. will be stove enameled on both sides. lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. all sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing clause 1701 and annexure 1700.1 providing and fixing maintenance information board of pmgsy project providing and fixing of maintenance information board for pmgsy project with logo as per mord specifications and drawing. two ms plates of 1.6 mm thick, top and bottom plate duly welded with ms flat iron 25mm x 5 mm size on back on edges. the plates will be welded with ms angle iron frame of 25mm x 25mm x 5mm. the angle iron frame of the plates will be welded to 2 nos. 75mm x 75mm of 12 swg sheet tubes posts duly embedded in cement concrete m-15 grade blocks of 600mm x 600mm x 750mm, 750mm below ground level. all m.s. will be stove enamelled on both sides. lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. all sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing clause 1701 and annexure 1700.1 traffic signs/retro-reflectorised traffic signs providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per irc:67 made of encapsulated lens type reflective sheeting vide clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with m15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and technical specification clause 801. a 600 mm dia circle b 600 mm equilateral triangle providing and fixing pmgsy logo board at starting point steel tube providing and fixing of typical pmgsy logo board as per mord specifications and drawing. one plate of 1.6mm thick with ms flat 25mm x 5mm size on back on centre. the topmost diamond plate & mid. plate will be welded to 75mm x 75mm 0f 12 swg steel plate tube posts & dully embedded to cc 450mm x 450mm x 600mm below gl. lettering and printing etc. will be with ready mixed synthetic enamel paint of superior. direction and place identification signs upto 0.90 sqm size board a. retro-reflectorised traffic signs providing and erecting direction and place identification retro-reflectorised sheeting vide clasue 1701.2.3., fixed over aluminium sheeting 2mm thick with area not exceeding 0.90 sqm supported on a mild steel angle iron posts 75 x 75 x 6 mm firmly fixed to the gorund by means of properly designed foundation with m-15 grade cement concrete 450 x 450 x 600mm, 600mm below ground level as per approved drawing and technical specifications clasuse 1701 granular sub-base/base/surface course with local materials table 400.13 by mix in place method normal construction of granular sub-base by providing local material spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at once and compacting with smooth wheel roller to achieve the desired density complete as per clause 401.4 as per technical specification clause 408. i using naturally occuring gravel wbm grading 2 providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kn in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per technical specification clause 405. a by manual means wbm grading 3 providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kn in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per technical specification clause 405. a by manual means prime coat:low porosity providing and applying primer coat with bitumen emulsion ss-1 on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per technical specification clause 502.a by manual means tack coat providing and applying tack coat with bitumen emulsion rs-1 using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared bituminous surface cleaned with hydraulic broom as per technical specification clause 503. a by manual means 20mm thick open-graded premix carpet using bituminous penetration grade/modified bitumen binder providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kn static roller capacity, finished to required level and grades to be followed by seal coat of either type a or type b or type c as per technical specification clause 508. using plastic waste case-i by manual means i bitumens-90 seal coat providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using type a, type b and type c as per technical specification clause 510. case ii : type b by manual meansi bitumens-90 construction of 1.50 m span rcc slab culvert 4.63ht.3nos excavation for structures earthwork in excavation for structures as per drawing and technical specifications clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. i ordinary soil i upto 3m depth. providing concrete for plain/ reinforced concrete in open foundation complete as per drawings and technical specifications clause 802, 803, 1202 &1203 ipcc grade m 10, i nominal mix. 1:3:6 plain/reinforced cement concrete in substructure complete as per drawings and technical specification clauses 802, 804, 805, 806, 807, 1202 ans 1204 i pcc m 15 i nominal mix 1:2.5:5 providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications clauses 800, 1205.4 and 1205.5 ii. rcc grade m 25 supplying, fitting, and placing hysd bar reinforcement in superstructure complete as per drawing and technical specifications clauses 1002, 1010 and 1202 providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia ac pipe extending through the full width of the structures with slope of 1v:20h towards drawing face complete as per drawing and technical specification clauses 614, 709, 1204.3.7 providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and technical specification clause 1204.3.8 construction of retaining wall : height 4 m5nos excavation for structures earthwork in excavation for structures as per drawing and technical specifications clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50m, dressing of sides and bottom and backfilling in trenches with excavated suitable material i ordinary soil i upto 3m depth providing concrete for plain/ reinforced concrete in open foundation complete as per drawings and technical specifications clause 802, 803, 1202 &1203 ipcc grade m 10, i nominal mix. 1:3:6 stone masonry in cement mortar for substructure complete as per drawing & technical specification clauses 702, 704, 1202 and 1204 iii random rubble masonry ii in 1:4 cement mortar providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia ac pipe extending through the full width of the structures with slope of 1v:20h towards drawing face complete as per drawing and technical specification clauses 614, 709, 1204.3.7 providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and technical specification clause 1204.3.8 pointing with cement mortar 1:3 on brickwork as per drawing and technical sepecification clauses 613.3 and 1204 maintenance component for 5five years after construction not to be quoted yearwise

State Government

TRN :19033830 | 21 Sep, 2020

Tender Value : 1.31 Crore

Begusarai - Bihar

Tender for providing & fixing of bench mark pillars @ four nos per km as per drawings given and direction of e/i clearing and grubbing road land by manual means including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300mm, removals of stumps of such trees cut earlier & disposal of unserviceable materials & stacking of serviceable materials to be used or auctioned upto a lead of 1000 m including removal and disposal of top organic soil not exeeding 150mm in thickness as per technical specification - clause 201.1 and direction of e/i planting of trees and their maintenance for one year planting of trees by the road side avenue trees in 0.60 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge manure, planting the saplings, backfilling the trench, watering, fixing the tree guard and maintaining the plants for one year construction of embankment with approved material deposited from road way cutting and excavation from drain and foundation of other structures and excavated with an average lead of 50 m graded and compacted to meet requirement of tables 300.1 and 300.2 as per technical specification clause 301.5 excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross-sections, and transporting to the embankment location with a lift upto 1.5 m and lead upto 1000 m as per technical specification clause 302.3 construction of embankment with material obtained from borrow pits with a lift upto 1.5 m, transporting to the site spreading, grading to required slope and compacting to meet requirement of tables 300.1 and 300.2 with a lead upto 1000 m as per technical specification clause 301.5 . construction of granular sub-base by providing well graded material, spreading in uniform layers with tractor mounted grader arrangement on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with smooth wheel roller to achieve the desired density, complete as per technical specification clause 401. by manual means water bound macadam grading-iii by mechanical means providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kn static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per technical specification clause 405. providing and applying primer coat with bitumen emulsion ss-1 on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.90- 1.2 kg/sqm using mechanical means as per technical specification clause 502. providing and applying tack coat with bitumen emulsion rs using emulsion distributor @ 0.25 to 0.30 kg per sq m on the prepared bituminous surface cleaned with hydraulic broom as per technical specification clause 503. providing, laying and rolling of close-graded mix seal surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm type-a or 13.2 mm to 0.9 mm type-b aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kn static roller and finishing to required level and grades as per technical specification clause 509 cement concrete pavement construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per clause 1501.2.2 m30 grade, coarse and fine aggregates conforming to is:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing, spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, using curing compound where specified and water finishing to lines and grade as per drawing and technical specification clause 501 brick soling - laying brick soling layer on prepared sub-grade with brick on edge according to lines, graded and cross-section shown on the drawing filling joints with sand and earth, spreading 25 mm thick layer of earth over brick soling, watering and rolliing the same with three wheel road roller 80-100 kn as per technical specification clause 412 earthwork in excavation for structures as per drawing and technical specifications clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. laying first class bedding on well compacted sand, moorum or approved granular material as per clause 1105 ii fillling in foundation trenches as per drawing and technical specification clause 305.3.9 providing and laying rcc pipe np 3 300 mm dia providing and laying reinforced cement concrete pipe for irrigation purpose. providing concrete for plain/reinforced concrete in m-15 in open foundations and side walls of drain complete as per drawings and technical specifications clause 802, 803, 1202 & 1203 pcc m15 plain/reinforced cement concrete in substructure complete as per drawings and technical specification clauses 802, 804, 805, 806, 807, 1202 ans 1204 pcc m15 providing and laying reinforced cement concrete pipe np3 for culverts on cement concrete bedding including fixing collar with cement mortor 1:2 but excluding excavation, protection works, backfilling, concrete and masonary works in head walls and parapets clauses 1106.1000 mm pipe in single row plastering with cm 1:4, 15mm thick on brickwork in substructure as per technical specification clause 613.4 & 1204 providing weepholes in brick masonry/ stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia ac pipe extending through the full width of the structures with slope of 1v:20h towards drawing face complete as per drawing and technical specification clauses 614, 709, 1204.3.7 brick masonry work in cement mortar in foundation complete excluding pointing and plastering as per drawing and technical specifications clauses 600, 1202 & 1203 brick work 1:4 brick masonry work in cement mortar in substructure complete excepting pointing and plastering, as per drawing and technical specification clauses 602, 603, 604, 1202 & 1204 brick work 1:3 reinforced cement concrete m15 grade kilometre local stone of standard design asper irc:8 fixing in position including painting and printing, etc as per drawing and technical specification clause 1703. km stone reinforced cement concrete m15 grade kilometre local stone of standard design asper irc:8 fixing in position including painting and printing, etc as per drawing and technical specification clause 1703. 200 m stone boundary pillar :reinforced cement concrete m15 grade boundary pillars/local stone of standard design as per irc:25, fixed in position including finishing and lettering but excluding painting as per drawing and technical specification clause 1704 traffic sign providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per irc :67 made of 1.5 mm thick ms steel duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per clause 1701.3.9 of mord for rural road of required shade and colour supported and welded on 47mm x 47mm x 12swg sheet tube firmly fixed to the ground by mean of properly designed foundation with m15 grade cement concrete 450x450x600 mm, 600mm below ground level as per approved drawing clause 1701.2.2. 900 mm equilateral & triangle, or 600 mm equilateral & triangle, or direction sign providing and erectig direction and place identification semi reflective sign board as per irc:67 made of 2 mm thick ms steel duly stove white colour in front and gray colour on back with red reflective border of 70 mm width and required letters and figures with reflective tape engineering grade as per clause 1701.3.9 of mord for rural road of required shade and colour supported and welded on 47mmx47mmx12swg square tube of 3050mm height duly strengthened by 25mmx5mm ms flat iron on edges on back firmly concrete 450x450x600 mm, 600mm below ground level as per approved drawing clause 1701.2.2. i providing and fixing logo of mmgsy project iii providing & fixing of logo of citizen information board five year maintenanace board road marking with hot applied thermoplastic compound with reflectorising glass beads on bituminous surface providing and applying 2 coats of water based cement paint to unplastered concrete surface after cleaning the surface of dirt, dust, oil, grease, efflorescence and applying paint @ of 1 litre for 2 sqm. painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and technical specification clause 1701 first year maintenance cost second year maintenance cost third year maintenance cost forth year maintenance cost fifth year maintenance cost add 1% labour cess add 12% gst add 10% seigniorage fee

State Government

TRN :19033917 | 21 Sep, 2020

Tender Value : 2.98 Crore

Begusarai - Bihar

Tender for construction of road bakhri khagaria mukhya path danraha hari singh to danraha hari singh reference pillars clearing and grubbing road land by manual means including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300mm, removals of stumps of such trees cut earlier & disposal of unserviceable materials & stacking of serviceable materials to be used or auctioned upto a lead of 1000 m including removal and disposal of top organic soil not exeeding 150mm in thickness as per technical specification-clause 201.1 and direction of e/i box cutting-excavation for roadway in soil using manual means for carrying of cut earth to embankment site with a lift upto 1.5 m and lead upto 50 m as per technical specification clause 302.3 construction of embankment with material obtained from borrow pits with a lift upto 1.5 m, transporting to the site spreading, grading to required slope and compacting to meet requirement of tables 300.1 and 300.2 with a lead upto 1000 m & 100 m as per technical specification clause 301.5 . including royality & labour cess. for 1000 m lead construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table 300.2 with lead upto 1000 m & 100 m as per technical specification clause 303.1. granular sub-base with coarse graded material -for grading i material -construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with smooth wheel roller to achieve the desired density, complete as per technical specification clause 401. wbm grading 3 by mechanical means -providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kn in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per technical specification clause 405. cement concrete pavement -construction of un-reinforced, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per clause 1501.2.2 m30 grade, coarse and fine aggregates conforming to is:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing, spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, using curing compound where specified and water finishing to lines and grade as per drawing and technical hard shouldering -laying brick soling layer on prepared sub-grade with brick on end edging according to lines, graded and cross-section shown on the drawing filling joints with sand and earth, spreading 25 mm thick layer of earth over brick soling, watering and rolliing the same with three wheel road roller 80-100 kn as per technical specification clause 412 ii km stone boundary pillar-reinforced cement concrete m15 grade boundary pillars/local stone of standard design as per irc:25, fixed in position including finishing and lettering but excluding painting as per drawing and technical specification clause 1704 culvert & curve traffic sign-providing and fixing of retro reflective cautionary, mandatory and informatory sign board as per irc :67 made of 1.5 mm thick ms steel duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per clause 1701.3.9 of mord for rural road of required shade and colour supported and welded on 47mmx47mmx12swg sheet tube firmly fixed to the ground by mean of properly designed foundation with m15 grade cement concrete 450x450x600 mm, 600mm below ground level as per approved drawing clause 1701.2.2. 600 mm equilateral & triangle, left/right curve 600 mm circular, speed limit 900 mm side octagon, or road marking with hot applied thermoplastic compound with reflectorising glass beads on bituminous surface-providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per irc:35 .the finished surface to be level, uniform and free from streaks and holes. road marking with hot applied thermoplastic compound with reflectorising glass beads on concrete surface-providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per irc:35 .the finished surface to be level, uniform and free from streaks and holes.-providing and applying 2 coats of water based cement paint to unplastered concrete surface after cleaning the surface of dirt, dust, oil, grease, efflorescence and applying paint @ of 1 litre for 2 sqm. cable duct across the roadfor irrigation purpose-providing and laying of a reinforced cement concrete pipe duct, 300 mm dia, across the road new construction, extending from drain to drain in cuts and toe of slope to toe of slope in fills, constructing head walls at both ends, providing a minimum fill of granular material over top and sides of rcc pipe as per irc:981997, bedded on a 0.3 m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe subject to minimum 450 mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per irc: 98 - 1997 and approved drawings. single row cable duct @ 4 no. per km 3 no. pipe 7.5 m in length direction and place indentification signs up to 0.9 sqm size board-providing and erecting direction and place identification retro-reflectorised sign as per irc:67 made of encapsulated lens type reflective sheeting vide clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with m-15 grade cement concrete 450 x 450 x 600 mm, 600 mm below ground level as per approved drawing and technical specification clause 1701 iproviding and fixing logo of project -providing and fixing of typical mmgsy informatory sign board with logo as per mord specifications and drawing. three ms plates of 1.6 mm thick, top and middle plate duly welded with ms flat iron 25mm x 5m size on back on edges. the lower plate will be welded with ms angle iron frame of 25mm x 25mm x 5mm. the angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 swg sheet tubes posts duly embedded in cement concrete m-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. the top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 swg steel plate tube. all m.s. will be stove enameled on both sides. lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. all sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing clause 1701 and annexure 1700.1 providing m15 pcc 1:2.5:5 as levelling course in foundation :-- providing pcc m 15 1:2.5:5 concrete for plain concrete in open foundations complete as per drawings and technical specifications clause 802, 803, 1202 & 1203 five year maintenance cost seigniorage fee 10% for material rate including royality add gst @ 12 % add labour cess @ 1 % durga asthan to dumari durga asthan tola reference pillars clearing and grubbing road land by manual means including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300mm, removals of stumps of such trees cut earlier & disposal of unserviceable materials & stacking of serviceable materials to be used or auctioned upto a lead of 1000 m including removal and disposal of top organic soil not exeeding 150mm in thickness as per technical specification-clause 201.1 and direction of e/i box cutting-excavation for roadway in soil using manual means for carrying of cut earth to embankment site with a lift upto 1.5 m and lead upto 50 m as per technical specification clause 302.3 construction of embankment with material obtained from borrow pits with a lift upto 1.5 m, transporting to the site spreading, grading to required slope and compacting to meet requirement of tables 300.1 and 300.2 with a lead upto 1000 m & 100 m as per technical specification clause 301.5 . including royality & labour cess. for 1000 m lead construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table 300.2 with lead upto 1000 m & 100 m as per technical specification clause 303.1. granular sub-base with coarse graded material -for grading i material -construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with smooth wheel roller to achieve the desired density, complete as per technical specification clause 401. wbm grading 3 by mechanical means -providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kn in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per technical specification clause 405. cement concrete pavement -construction of un-reinforced, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per clause 1501.2.2 m30 grade, coarse and fine aggregates conforming to is:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing, spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, using curing compound where specified and water finishing to lines and grade as per drawing and technical hard shouldering -laying brick soling layer on prepared sub-grade with brick on end edging according to lines, graded and cross-section shown on the drawing filling joints with sand and earth, spreading 25 mm thick layer of earth over brick soling, watering and rolliing the same with three wheel road roller 80-100 kn as per technical specification clause 412 ii km stone iii 200 m stone boundary pillar-reinforced cement concrete m15 grade boundary pillars/local stone of standard design as per irc:25, fixed in position including finishing and lettering but excluding painting as per drawing and technical specification clause 1704 culvert & curve traffic sign-providing and fixing of retro reflective cautionary, mandatory and informatory sign board as per irc :67 made of 1.5 mm thick ms steel duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per clause 1701.3.9 of mord for rural road of required shade and colour supported and welded on 47mmx47mmx12swg sheet tube firmly fixed to the ground by mean of properly designed foundation with m15 grade cement concrete 450x450x600 mm, 600mm below ground level as per approved drawing clause 1701.2.2. 600 mm equilateral & triangle, left/right curve 600 mm circular, speed limit 900 mm side octagon, or road marking with hot applied thermoplastic compound with reflectorising glass beads on bituminous surface-providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per irc:35 .the finished surface to be level, uniform and free from streaks and holes. road marking with hot applied thermoplastic compound with reflectorising glass beads on concrete surface-providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per irc:35 .the finished surface to be level, uniform and free from streaks and holes.-providing and applying 2 coats of water based cement paint to unplastered concrete surface after cleaning the surface of dirt, dust, oil, grease, efflorescence and applying paint @ of 1 litre for 2 sqm. cable duct across the roadfor irrigation purpose-providing and laying of a reinforced cement concrete pipe duct, 300 mm dia, across the road new construction, extending from drain to drain in cuts and toe of slope to toe of slope in fills, constructing head walls at both ends, providing a minimum fill of granular material over top and sides of rcc pipe as per irc:981997, bedded on a 0.3 m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe subject to minimum 450 mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per irc: 98 - 1997 and approved drawings. single row cable duct @ 4 no. per km 3 no. pipe 7.5 m in length direction and place indentification signs up to 0.9 sqm size board-providing and erecting direction and place identification retro-reflectorised sign as per irc:67 made of encapsulated lens type reflective sheeting vide clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with m-15 grade cement concrete 450 x 450 x 600 mm, 600 mm below ground level as per approved drawing and technical specification clause 1701 iproviding and fixing logo of project -providing and fixing of typical mmgsy informatory sign board with logo as per mord specifications and drawing. three ms plates of 1.6 mm thick, top and middle plate duly welded with ms flat iron 25mm x 5m size on back on edges. the lower plate will be welded with ms angle iron frame of 25mm x 25mm x 5mm. the angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 swg sheet tubes posts duly embedded in cement concrete m-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. the top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 swg steel plate tube. all m.s. will be stove enameled on both sides. lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. all sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing clause 1701 and annexure 1700.1 providing m15 pcc 1:2.5:5 as levelling course in foundation :-- providing pcc m 15 1:2.5:5 concrete for plain concrete in open foundations complete as per drawings and technical specifications clause 802, 803, 1202 & 1203 five year maintenance cost seigniorage fee 10% for material rate including royality add gst @ 12 % add labour cess @ 1 % muslim tol sh-55 to muslim tol setting out pillars -providing & fixing of working benchmark pillars 01 nos. per km & 04 nos. of reference pillars required for 1 km. as per drawings given and direction of e/i working benchmark pillars reference pillars clearing and grubbing road land by manual means including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300mm, removals of stumps of such trees cut earlier & disposal of unserviceable materials & stacking of serviceable materials to be used or auctioned upto a lead of 1000 m including removal and disposal of top organic soil not exeeding 150mm in thickness as per technical specification-clause 201.1 and direction of e/i box cutting-excavation for roadway in soil using manual means for carrying of cut earth to embankment site with a lift upto 1.5 m and lead upto 50 m as per technical specification clause 302.3 construction of embankment with material obtained from borrow pits with a lift upto 1.5 m, transporting to the site spreading, grading to required slope and compacting to meet requirement of tables 300.1 and 300.2 with a lead upto 1000 m & 100 m as per technical specification clause 301.5 . including royality & labour cess. for 1000 m lead for 100 m lead construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table 300.2 with lead upto 1000 m & 100 m as per technical specification clause 303.1. granular sub-base with coarse graded material -for grading i material -construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with smooth wheel roller to achieve the desired density, complete as per technical specification clause 401. wbm grading 3 by mechanical means -providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kn in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per technical specification clause 405. prime coat low porosity-providing and applying primer coat with bitumen emulsion ss-1 on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70- 1.0 kg/sqm using mechanical means as per technical specification clause 502. tack coat -providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surface tretaed with primer and clened with hydriloc broom as per technical specification aclouse 503. mss-mix seal surface type-b bituminous s-90-providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 13.2 mm to 0.9 mm type-b aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kn static roller and finishing to required level and grades as per technical specification clause 509 cement concrete pavement -construction of un-reinforced, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per clause 1501.2.2 m30 grade, coarse and fine aggregates conforming to is:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing, spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, using curing compound where specified and water finishing to lines and grade as per drawing and technical hard shouldering -laying brick soling layer on prepared sub-grade with brick on end edging according to lines, graded and cross-section shown on the drawing filling joints with sand and earth, spreading 25 mm thick layer of earth over brick soling, watering and rolliing the same with three wheel road roller 80-100 kn as per technical specification clause 412 ii km stone iii 200 m stone boundary pillar-reinforced cement concrete m15 grade boundary pillars/local stone of standard design as per irc:25, fixed in position including finishing and lettering but excluding painting as per drawing and technical specification clause 1704 culvert & curve traffic sign-providing and fixing of retro reflective cautionary, mandatory and informatory sign board as per irc :67 made of 1.5 mm thick ms steel duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per clause 1701.3.9 of mord for rural road of required shade and colour supported and welded on 47mmx47mmx12swg sheet tube firmly fixed to the ground by mean of properly designed foundation with m15 grade cement concrete 450x450x600 mm, 600mm below ground level as per approved drawing clause 1701.2.2. 600 mm equilateral & triangle, left/right curve 600 mm circular, speed limit 600mm x 450mm reactangular informatory board 900 mm side octagon, or road marking with hot applied thermoplastic compound with reflectorising glass beads on bituminous surface-providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per irc:35 .the finished surface to be level, uniform and free from streaks and holes. road marking with hot applied thermoplastic compound with reflectorising glass beads on concrete surface-providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per irc:35 .the finished surface to be level, uniform and free from streaks and holes.-providing and applying 2 coats of water based cement paint to unplastered concrete surface after cleaning the surface of dirt, dust, oil, grease, efflorescence and applying paint @ of 1 litre for 2 sqm. cable duct across the roadfor irrigation purpose-providing and laying of a reinforced cement concrete pipe duct, 300 mm dia, across the road new construction, extending from drain to drain in cuts and toe of slope to toe of slope in fills, constructing head walls at both ends, providing a minimum fill of granular material over top and sides of rcc pipe as per irc:981997, bedded on a 0.3 m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe subject to minimum 450 mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per irc: 98 - 1997 and approved drawings. single row cable duct @ 4 no. per km 3 no. pipe 7.5 m in length direction and place indentification signs up to 0.9 sqm size board-providing and erecting direction and place identification retro-reflectorised sign as per irc:67 made of encapsulated lens type reflective sheeting vide clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with m-15 grade cement concrete 450 x 450 x 600 mm, 600 mm below ground level as per approved drawing and technical specification clause 1701 iproviding and fixing logo of project -providing and fixing of typical mmgsy informatory sign board with logo as per mord specifications and drawing. three ms plates of 1.6 mm thick, top and middle plate duly welded with ms flat iron 25mm x 5m size on back on edges. the lower plate will be welded with ms angle iron frame of 25mm x 25mm x 5mm. the angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 swg sheet tubes posts duly embedded in cement concrete m-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. the top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 swg steel plate tube. all m.s. will be stove enameled on both sides. lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. all sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing clause 1701 and annexure 1700.1 planting of tree & there maintainance for one year- planting of tree by the road side avenue tree in 0.6 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/ slug manure, planting the saplings back filling the trench, watering, fixing the tree guard & maintain the plant for one year. earth work in excavation for foundation of structures upto 3.0 m depth as per drawing and technical specification clause 1104 providing m15 pcc 1:2.5:5 as levelling course in foundation :-- providing pcc m 15 1:2.5:5 concrete for plain concrete in open foundations complete as per drawings and technical specifications clause 802, 803, 1202 & 1203 brick masonary work in cm 1:4 in head wall complete as per drawing and technical specification clause 1109 in cement mortar 1:4 providing and laying rcc pipe np-3 for culverts on first class bedding of pcc m10 material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling concrete and masonary works in head walls and parapets as per clause 1106 plastering with cement mortar 1:4 on brick work in sub-structure as per technical specifications providing 1.5 mm cement punning including curing carriage of water with all leads and lifts as per building specification and direction of e/i painting two coats on new concrete surfaces black & white strips :-painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and technical specification clause 1701 five year maintenance cost seigniorage fee 10% for material rate including royality add gst @ 12 % add labour cess @ 1 % phaphot pwd to phaphot reference pillars clearing and grubbing road land by manual means including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300mm, removals of stumps of such trees cut earlier & disposal of unserviceable materials & stacking of serviceable materials to be used or auctioned upto a lead of 1000 m including removal and disposal of top organic soil not exeeding 150mm in thickness as per technical specification-clause 201.1 and direction of e/i for 100 m lead construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table 300.2 with lead upto 1000 m & 100 m as per technical specification clause 303.1. granular sub-base with coarse graded material -for grading i material -construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with smooth wheel roller to achieve the desired density, complete as per technical specification clause 401. wbm grading 3 by mechanical means -providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kn in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per technical specification clause 405. prime coat low porosity-providing and applying primer coat with bitumen emulsion ss-1 on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70- 1.0 kg/sqm using mechanical means as per technical specification clause 502. tack coat -providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surface tretaed with primer and clened with hydriloc broom as per technical specification aclouse 503. mss-mix seal surface type-b bituminous s-90-providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 13.2 mm to 0.9 mm type-b aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kn static roller and finishing to required level and grades as per technical specification clause 509 hard shouldering -laying brick soling layer on prepared sub-grade with brick on end edging according to lines, graded and cross-section shown on the drawing filling joints with sand and earth, spreading 25 mm thick layer of earth over brick soling, watering and rolliing the same with three wheel road roller 80-100 kn as per technical specification clause 412 ii km stone iii 200 m stone boundary pillar-reinforced cement concrete m15 grade boundary pillars/local stone of standard design as per irc:25, fixed in position including finishing and lettering but excluding painting as per drawing and technical specification clause 1704 culvert & curve traffic sign-providing and fixing of retro reflective cautionary, mandatory and informatory sign board as per irc :67 made of 1.5 mm thick ms steel duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per clause 1701.3.9 of mord for rural road of required shade and colour supported and welded on 47mmx47mmx12swg sheet tube firmly fixed to the ground by mean of properly designed foundation with m15 grade cement concrete 450x450x600 mm, 600mm below ground level as per approved drawing clause 1701.2.2. 600 mm equilateral & triangle, left/right curve 600 mm circular, speed limit 600mm x 450mm reactangular informatory board road marking with hot applied thermoplastic compound with reflectorising glass beads on bituminous surface-providing and laying of hot applied thermoplastic compound 2.5 mm thick including r

Central Government/Public Sector

TRN :19022679 | 25 Sep, 2020

Tender Value : NA

Faridabad - Haryana

Tender for supply of aluminium oxide grit for manufacturing of gi barrels

Central Government/Public Sector

TRN :19013571 | 21 Sep, 2020

Tender Value : NA

Tiruchirappalli - Tamil Nadu

Tender for supply of aluminium oxide resin disc size 127 mm x 22.23 mm grit 36. make: grindwell norton/carborundum universal oem / authorized dealers should only quote. dealership certificate should be uploaded along with the offer, without which the offer will not be considered. month & year of manufacture of discs should be within 4 months at the time of supply.

corporations/Associations/Others

TRN :19007960 | 28 Sep, 2020

Tender Value : NA

Varanasi - Uttar Pradesh

Tender for supply of 20mm aggregate, course sand for bridge

Central Government/Public Sector

TRN :18996104 | 30 Sep, 2020

Tender Value : NA

Jaisalmer - Rajasthan

Tender for supply of stores - cement ppc/opc 53 grade make: ultratech / ambuja / acc / birla/jk laxmi sand coarse to be approved by consignee authority stone aggregate 20mm nominal size stone aggregate 40mm stone aggregate 63mm to 75mm pcc solid blocks of size 400 x 200 x 200 mm in pcc 1:2:4 pvc unarmed aluminum cable 10 sqmm 2 core make : anchor/ havells/ finolex switch socket combination 16 amps 6 pin modular with weatherproof box protect from rain, sunlight etc. as directed by engr-in-charge. make : anchor / crabtree / indoasian/ siemens / l&t pvc copper cable insulated multi standard 2.5 sqmm. colour : black & red. make : anchor / havel’s / finolex mcb db enclosure 8 way complete sheet metal enclosures make : anchor / c&g / l&t mcb spn 40 amps make : anchor /indoasian/ philips / bajaj mcb sp 16 amps, 10 ka cseries. make : anchor /indoasian/ philips / bajaj pvc capping/casing 25mm with accessories isi marked. make : anchor /indoasian/ philips / bajaj earthing complete with copper plate as per specification. nut & bolt 16 mm dia with steel washer ms angle 75 x 75 x 6 mm thick duly painted with two coats of synthetic enamel paint over a coat of red oxide. make : tata /sail /jindal/bhushan/apl apollo ms plate 3 mm thick duly painted with two coats of synthetic enamel paint over a coat of red oxide. make : tata /sail /jindal/bhushan/apl apollo ms rod 6 mm dia duly painted with two coats of synthetic enamel paint over a coat of red oxide. make : tata /sail /jindal/bhushan/apl apollo cement base paint make : snowcem / jhonson / asian cement primer first quality make : asian / nerolac / berger / shalimar hiring of jcb for 16 or plinth add skilled labour 1, panel board., hammer med size 1kg taparia shovel/ phowda with handle set of screw drivers taparia electric tester taparia hacksaw frame painting brush 100mm hacksaw blade double ended measuring tape 30 mtrs durmut 10 kg pan mortar tasla trowel mason mason square plumb bob with cotton thread cutting pliers taparia measuring tape steel 3 mtrs plaster trowel wooden 450 mm plaster trowel steel tube level pipe 4mm of 15m length welding rod sprit level thread mason 100 mtr long rubber hand gloves for orl plinth

Central Government/Public Sector

TRN :18996485 | 30 Sep, 2020

Tender Value : NA

Jaisalmer - Rajasthan

Tender for supply of stores for ojl plinth- cement ppc/opc 53 grade make:ultratech / ambuja / acc / birla/jk laxmi sand coarse to be approved by consignee authority stone aggregate 20mm nominal size stone aggregate 40mm stone aggregate 63mm to 75mm pcc solid blocks of size 400 x 200 x 200 mm in pcc 1:2:4 pvc unarmed aluminum cable 10 sqmm 2 core make : anchor/ havells/finolex switch socket combination 16 amps 6 pin modular with weatherproof box protect from rain, sunlight etc. as directed by engr-in-charge. make : anchor / crabtree / indoasian/ siemens / l&t pvc copper cable insulated, multi standard 2.5 sqmm. colour : black & red. make : anchor / havells / finolex mcb db enclosure 8 way complete sheet metal enclosures make : anchor / c&g / l&t mcb spn 40 amps make : anchor /indoasian/ philips / bajaj mcb sp 16 amps, 10 ka cseries. make : anchor /indoasian/ philips / bajaj pvc capping / casing 25mm with accessories isi marked. make : anchor /indoasian/ philips / bajaj earthing complete with copper plate as per specification. nut & bolt 16 mm dia with steel washer ms angle 75 x 75 x 6 mm thick duly painted with two coats of synthetic enamel paint over a coat of red oxide. make : tata /sail /jindal/bhushan/apl apollo ms plate 3 mm thick duly painted with two coats of synthetic enamel paint over a coat of red oxide. make : tata /sail /jindal/bhushan/apl apollo ms rod 6 mm dia duly painted with two coats of synthetic enamel paint over a coat of red oxide. make : tata /sail /jindal/bhushan/apl apollo cement base paint make : snowcem / jhonson / asian cement primer first quality make : asian / nerolac / berger / shalimar add skilled labour 1 hiring of jcb for 09 ojl plinth hammer med size 1kg taparia shovel/ phowda with handle set of screw drivers taparia electric tester taparia hacksaw frame painting brush 100mm hacksaw blade double ended measuring tape 30 mtrs durmut 10 kg pan mortar tasla trowel mason mason square plumb bob with cotton thread cutting pliers taparia measuring tape steel 3 mtrs plaster trowel wooden 450 mm plaster trowel steel tube level pipe 4mm of 15m length welding rod sprit level thread mason 100 mtr long rubber hand gloves

State Government

TRN :18987611 | 24 Sep, 2020

Tender Value : NA

Medinipur - West Bengal

Tender for supply of 1st class picked jhama brickstraditional laterite boulder fine sand medium sand coarse sand bamboo 8cm-10cm dia including fixing eucalyptus bullah 7.5cm -10cm dia eucalyptus bullah 12.5cm -15cm dia eucalyptus bullah 17.5cm -20cm dia sal bullah 7.5cm -10cm dia sal bullah 12.5cm -15cm dia sal bullah 17.5cm -20cm dia nail hire charges of shuttering plank 25mm-30mm thick with prop including all fittings hire charges of shuttering plank 25mm-30mm thick without prop including all fittings hire charges of shuttering plank above 30mm-37mm thick with prop including all fittings hire charges of 5 kva generator hire charges of 3 kva generator hire charges of monkey set loading unloading & stacking sand/ stone aggregate less than 40mm nominal size loading unloading & stacking stone aggregate above 40mm nominal size loading unloading & stacking lime, moorum, building rubish and similar miscellaneous material hire charges of diesel road roller- 8 to 10 tonne diesel oil 1st class traditional bricks kiln burnt loading, unloading & stacking by manual means r.c.c. pipes, c.i. pipes and unreinforced cement pipes 600, 700, 750 & 800 mm dia loading, unloading & stacking by manual means r.c.c. pipes, c.i. pipes and unreinforced cement pipes 900 mm dia loading, unloading and stacking by manual means r.c.c. pipes, c.i. pipes and unreinforced cement pipes 1000, 1100 & 1200 mm dia coloured inter locking c.c. paver block river bed material sausage wire net wood dust tor steel rods/hysd bars/tmt bars sail/tata/rinl fe415/fe500/fe500d conforms to is: 1786 tor steel rods/hysd bars/tmt barsjsw/jspl/shyam/srmb/bmasl/elecrosteel/sslfe415/fe500/fe500d conforms to is: 1786 tor steel rods/hysd bars/tmt bars other than sail/tata/rinl/jsw/jspl/shyam/srmb/bmasl/elecrosteel/sslfe415/fe500/fe500d conforms to is: 1786 loading, unloading and stacking by manual means of steel sal silliguri sal malaysia neem wood other local wood ordinary teak wood sisu/gamar wood local sal wood portland cement stone aggregatesingle size: 40 mm nominal size bright finished or black enameled mild steel butt hinges 50x37x 1.50 mm bright finished or black enameled mild steel butt hinges 75x47x 1.70 mm bright finished or black enameled mild steel butt hinges 100x58x 1.90 mm coal tarring fan hook r.c.c ventilator of 20 mm. thick upto 0.10 sq.m. area r.c.c ventilator of 20 mm. thick above 0.10 sq.m. area udaypur marble slab for floor, lobby etc 18 mm thick of size 0.3 sq m to 0.6 sq m chawk dungri marble slab for floor, lobby etc 18 mm thick of size 0.3 sq m to 0.6 sq m udaypur marble slab for wall/dado 18 mm thick of size 0.3 sq m to 0.6 sq m chawk dungri marble slab for wall/dado 18 mm thick of size 0.3 sq m to 0.6 sq m frp composite door frame 66mm x 70mm frp composite door frame 66mm x 90mm coloured pedestal type w.c. pan 580x440 mm european type s trap ceramic glazed tiles ist quality 300 x 300 mm in all shades and designs of white, ivory, grey, fume red brown etc. 18 mm thick marble partition slab for urinals including fitting fixing with chawk doongri marble stone aggregatesingle size:20 mm nominal size stone aggregatesingle size: 10 mm nominal size cpvc chlorinated polyvinyl chloride pipes 15 mm dia for concealed work cpvc chlorinated polyvinyl chloride pipes 20 mm dia for concealed work cpvc chlorinated polyvinyl chloride pipes 25 mm dia for concealed work thermocol 12.5 mm thick. rectified - ceramic glazed tiles ist quality 300 x 300 mm or more in all shades designs white, ivory, grey, fume red brown etc vitrified floor tile 60x60 cm polythene bib cock / stop cock hd with metal/plastic inlet emco / atlas or equivalent sink 630 mm x 550 mm x 180 mm with waste fittings and two coats of painting of c.i. brackets supplying, fitting and fixing pillar cock of approved make cp pillar cock - 15 mm equivalent to code no. 507 & model tropical / sumthing special of essco or similar brand. precast chequered cement tiles 22 mm thick dark shade using ordinary cement structural members of specified sections weighing less than -22.5 kg./m e.g. joists, angle, channel sections conforming to is: 226, is: 808 & sp 6- 1964 structural works in roof trusses etc. using joists, channels and angles of specified section conforming to is: 226, is: 808 & sp 6- 1964 weighing less than 22.5 kg/ m m.s. structural works in roof trusses with tubular sections conforming to is: 806-1968 & is: 1161- 1998 trusses spanning up to 12.00 m m.s. structural with hollow sections square or rectangular shape conforming to is: 806-1968 & is:1161-1998 span up to 12 mtr stone aggregatesingle size: 06 mm nominal size water proofing materials carriage of r.c.c. pipes 1000 mm dia fly ash brickstraditional r.c.c. pipes np2 class 300 mm dia r.c.c. pipes np2 class 450 mm dia rcc pipe 600 mm dia np- 3 spigot rcc pipe 900 mm dia np - 3 spigot rcc pipe 1000 mm dia np -3 spigot rcc pipe 1200 mm dia np - 3 spigot carriage of r.c.c. pipes 900 mm dia towel rail cp over brass - 600 mm collapsible gate steel railing ms integrated grill for steel window and ventillator 1.5 mm thick ms sheet ci manhole cover 450 mm dia carriage of r.c.c. pipes 1200 mm dia malayasia sal cleat welding by electric plant openable steel windows as per is sizes with side hung shutters and horizotal glazing bars. float glass sheet of nominal thickness 4 mm weight not less than 10 kg/sqm fixed type ventilators as per i.s. sizes with horizontal glazing bars height being limited to 580 mm float glass sheet of nominla thickness 5.5 mm weight not less than 13.50 kg/ sqm empty gunny bag brick aggregate single size:40 mm nominal size stone aggregatesingle size:50 mm nominal size false ceiling with 4mm thick pearl designer fibre cement board stone aggregatesingle size:63 mm nominal size supplying, fitting & fixing asbestos corrugated sheet6 mm thick supplying, fitting & fixing asbestos ridging supplying, fitting & fixing zn-al alloy steel sheet work in roof supplying, fitting & fixing aluminium sheet ridging fitting and fixing glass reinforced polyester translucent fiber glass sheet fitting and fixing glass reinforced polyester translucent ridging fitting & fixing circular corrugated aluminium sheet supplying, fitting & fixing of 2-track / 3-track aluminium sliding window supplying, fitting & fixing of partly glazed partly paneled or fully glazed single leaf aluminium swing door supplying, fitting & fixing of aluminium fixed partition wall of all aluminium sections galvanised steel corrugated sheets galvanised steel bolts & nuts 6 mm dia and 25 mm long round head with slots galvanised steel j or l hooks 8 mm dia g.i limpet washer bitumen washer modular fly ash bricks precast cement concrete blocks nominal mix. 1:1.5:3 with 20 mm down coarse aggregate including supplying at site, laying and finishing the top surface with 1:3 cement mortar g.i. plain washer for seam bolts fencing post 215 cm 150 mm x 150 mm section at bottom, 100 mm x 100 mm section at top with t-base 300 mm x 150 mm x 100 mm, having 4 nos 6 mm dia vertical m.s. reinforcement and 6 mm dia binders @ 200 mm centres, finished smooth hydraulic door closer tubular type aluminium section body polythene sheet 150 gm per sqm grill weighing above 10 kg./sq.mtr and up to 16 kg./sq. mtr. galvanised steel plain sheets seam bolts and nuts 6 mm dia and 25 mm long shower jet corner urinal ci p trap ci s trap porcelain p trap porcelain s trap check valve 32mm check valve 40mm check valve 50mm hire charges for 5 hp pump with operator, fuel and shifting etc all charges complete bamboo roof truss 8cm-10cm dia including fixing moorum carriage of moorum polyethylene water storage tank with cover and suitable locking arrangemnet cost of neelgiri/maxican grass truf sqm cowdung brass 150 mm floor door stopper 0.357 kg anodised aluminium hanging type door stopper chromium plated brass mortice latch and lock 100x65 mm with 6 levers and a pair of brass lever handles 30 mm thick factory made glass fiber reinforced plastic panel door shutter i/c carriage upvc pipes working pressure 4 kg /cm2 single socketed pipe 75 mm dia silver sand upvc pipes working pressure 4 kg / cm2 single socketed pipe 110 mm dia unslaked lime glue green or blue medium shade pigment white cement water thinnable cement primer for interior wall surface, having voc content less than 50 gms/litre ready mixed pink or grey primer on wood work red oxide zinc chromate primer synthetic enamel paint in black or chocolate shade synthetic enamel paint, having voc volatile organic compound content less than 150 gm/liitre acrylic exterior paint superior copal varnish black japan chlorinated polyvinyl - chloride cpvc pipe 15 mm outer dia chlorinated polyvinyl - chloride cpvc pipe 20 mm outer dia chlorinated polyvinyl - chloride cpvc pipe 25 mm outer dia chlorinated polyvinyl - chloride cpvc pipe 32 mm outer dia chlorinated polyvinyl - chloride cpvc pipe 40 mm outer dia chlorinated polyvinyl - chloride cpvc pipe 50 mm outer dia shower rose c.p brass for 15 to 20 mm intel 100 mm dia shower rose c.p.brass for 15 to 20 mm intel 150 mm dia 20 mm dia gunmetal gate valve with wheel c.p.brass bibcock 15 mm c.p. brass long nose bibcock 15 mm c.p. brass long body bibcock 15 mm c.p. brass stop cock concealed 15 mm chromium plated stop cock equivalent to code no. 513a & 513b & model - tropical / sumthing special of essco or similar brand. chromium plated angular stop cock with wall flange equivalent to code no. 5053 & model - florentine of jaquar or similar brand. 15 mm ptmt bib cock orissa pattern water closet 530x410 mm ptmt pillar cock flushing cistern p.v.c. 10 lts capacity low level white with fittings, accessories and flush pipe vitreous china flat back wash basin 450x300 mm vitreous china flat back wash basin 630x450 mm vitreous china angle back wash basin 400x400 mm vitreous china flat back wash basin 550x400 mm vitreous china pedestal for wash basin g.i. pipes 15 mm dia g.i. pipes 20 mm dia g.i. pipes 25 mm dia g.i. pipes 32 mm dia g.i. pipes 40 mm dia g.i pipes 50 mm dia g.i. pipes 65 mm dia g.i. pipes 80 mm dia adhesive solvent cement upvc pipes working pressure 4 kg /cm2 single socketed pipe 75 mm dia upvc pipes working pressure 4 kg / cm2 single socketed pipe 110 mm dia upvc bend 87.50, 75 mm bend upvcbend 87.50, 110 mm bend upvc single equal tee without door 75x75x75 mm upvc single equal tee without door 110x110x110 mm upvc single equal tee with door 75x75x75 mm upvc single equal tee with door 110x110x110 mmmm upvc pipe clip 75 mm bend upvc pipe clip 110 mm bend slotted cowl terminal guard 75 mm dia slotted cowl terminal guard 100 mm dia circular shape 450 mm dia precast r.c.c. manhole cover with frame l.d. -25 coloured orissa pattern w.c. pan 580x440 mm coloured pedestal type w.c. pan 580x440 mm european type mirror of superior make glass 60x45 cm ptmt - liquid soap container of 400 ml capacity ptmt - soap dish/holder 138x102x75 mm vitreous china foot rests 250x125x25 mm vitreous china squatting plate urinal white vitreous china clay half stall urinal flat back 580x380x350 mm or angle back 450x375x350 mm with waste fittings as per is: 2556 c.i. grating 100x100 mm rolling shutter made of 80x1.25 mm machine rolled laths carriage of stone aggregate below 40 mm nominal size hire charges of concrete mixer 0.25 to 0.40 cum with hopper hire charges of vibrator needle type 40 mm carriage of stone aggregate 40 mm nominal size and above hire charges of surface vibrator including fuel operator etc all complete hire charges of water tanker for wbm road including fuel operator etc all complete paddy straw nylon net wire mesh rabbit g.i. wire for construction works for enayetpur gram panchayat under keshpur dev. block fund mgnrega.

Related Keywords : aggregate materials

List of latest aggregate-materials Tenders in Indian Tenders. Click on any aggregate-materials Tenders to view BOQ, NIT and Tender Documents. Get Bidding Support and Vendor Registration for aggregate-materials Tenders.

Tender for supply of aluminium oxide grit for manufacturing of gi barrels

Tender for supply of 20mm aggregate, course sand for bridge

Get aggregate materials Tender Alert...

Related Keywords : aggregate materials

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us