Filters

List of bore-work in howrah Tenders

List of latest bore-work in howrah Tenders in Indian Tenders. Click on any bore-work in howrah Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for bore-work in howrah Tenders.

All-Tenders (1)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

Central Government And Public Sector

TRN :49059263 | 17 May, 2025

Tender Value : 14.93 Lacs

Howrah - West Bengal

Tender for tender for structural strengthening and external painting of b e college t e howrah; 1 demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer - in - charge. 2 nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) 3 dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : 4 of area 3 sq. metres and below 5 dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. 6 for thickness of tiles 10 mm to 25 mm 7 dismantling c.i. pipes including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means breaking lead caulked joints, melting of lead and making into blocks including stacking of pipes & lead at site within 50 metre lead as per direction of engineer-in-charge: 8 up to 150 mm diameter 9 dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. 10 disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. 11 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level : 12 1:2:4 (1 cement : 2 coarse sand(zone-iii) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) 13 reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 14 1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii)derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) 15 reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii)derived from natural sources : 3 graded stone aggregate 20 mm nominal sizederived from natural sources). 16 reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers, facias and eaves boards above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-iii)derived from natural sources : 3 graded stone aggregate 20mm nominal size derived from natural sources). 17 centering and shuttering including strutting, propping etc. and removal of form for : 18 foundations, footings, bases of columns, etc. for mass concrete 19 columns, pillars, piers, abutments, posts and struts 20 vertical and horizontal fins individually or forming box louvers band, facias and eaves boards 21 small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like 22 smooth finishing of the exposed surface of r.c.c. work with 6 mm thick cement mortar 1:3 (1 cement : 3 fine sand). 23 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer-in-charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 24 providing and fixing fiber glass reinforced plastic (frp) door frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. the laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. the frame shall be covered with fiber glass from all sides. m.s. stay shall be provided at the bottom to steady the frame. 25 providing and fixing to existing door frames. 26 30 mm thick glass fibre reinforced plastic (frp) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick frp laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick frp laminate for panels conforming to is: 14856, including fixing to frames. 27 steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 28 in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. 29 providing and laying rectified glazed ceramic floor tiles of size 300x300mm or more (thickness to be specified by the manufacturer), of 1stquality conforming to is : 15622, of approved make, in colours white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4(1 cement: 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. 30 providing and fixing on wall face unplasticised - pvc moulded fittings/accessories for unplasticised rigid pvc rain water pipes conforming to is 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion. 31 single tee with door -110x110x110 mm 32 bend 87.5° -110 mm bend 33 15 mm cement plaster on the rough side of single or half brick wall of mix : 34 1:6 (1 cement: 6 fine sand) 35 finishing walls with acrylic smooth exterior paint of required shade : 36 new work (two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) 37 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: 38 two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. 39 removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 40 dismantling w.c. pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of engineer-in- charge. 41 providing and laying app (atactic polypropylene polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the samemembrane manufactured of density at 25°c, 0.87 - 0.89 kg/litre and viscocity 70 - 160 cps. over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. the vital physical and chemical parameters of the membrane shall be as under : joint strength in longitudinal and transverse direction at 23°c as 350/300 n/5 cm. tear strength in longitudinal and transverse direction as 60/80n. softening point of membrane not less than 150°c. cold flexibility shall be upto -2°c when tested in accordance with astm, d - 5147. the laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane : 42 3 mm thick 43 providing and fixing white vitreous china pedestal type (european type/ wash down type) water closet pan. 44 providing and fixing p.v.c. low level flushing cistern with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete. 45 10 litre capacity - white 46 providing and fixing solid plastic seat with lid for pedestal type w.c. pan complete : 47 white solid plastic seat with lid 48 providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively. 49 providing and fixing p.v.c. waste pipe for sink or wash basin including p.v.c. waste fittings complete. 50 flexible pipe -32 mm dia 51 providing and fixing ptmt bib cock of approved quality and colour. 52 15mm nominal bore, 86 mm long. weighing not less than 88 gms. 53 providing and fixing ptmt stop cock of approved quality and colour. 54 15 mm nominal bore, 86 mm long. weighing not less than 88 gms. 55 providing and fixing ptmt pillar cock of approved quality and colour . 56 15mm nominal bore, 107 mm long. weighing not less than 110 gms. 57 providing and fixing unplasticised p.v.c. connection pipe with ptmt nuts, collar and bush of approved quality and colour. 58 15 mm nominal bore with 45 cm length. 59 chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of engineer-in-charge 60 75 mm average thickness 61 50 mm average thickness 62 25 mm average thickness 63 cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of engineer-in-charge. 64 bars upto 12 mm diameter 65 bars above 12 mm diameter 66 providing, mixing and applying bonding coat of approved adhesive on chipped portion of rcc as per specifications and direction of engineer-in-charge complete in all respect. 67 sbr polymer (@10% of cement weight) modified cementitious bond coat @ 2.2 kg cement per sqm of surface area mixed with specified proportion of approved polymer 68 providing, mixing and applying sbr polymer (of approved make) modified cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of engineer-in-charge. note: measurement and payment: the pre-measurement of thickness shall be done just after the surface preparation is completed and payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 n/sqmm2). 69 12 mm average thickness. 70 25 mm average thickness in 2 layers. 71 50 mm average thickness in 3 layers. 72 providing and fixing upvc pipes (sch 40 upvc as per astm d- 1785 pipes) including all upvc plain and brass threaded fittings. including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step upvc solvent cement and testing of joints complete as per direction of engineer in charge. internal work- exposed on wall 73 15 mm nominal bore 74 20 mm nominal bore 75 25 mm nominal bore 76 uprooting and removing small plants from the surface of walls, parapet, etc. at any height by cutting chase for removing roots and using necessary chemicals etc. to prevent further growth of plants and mending good damages complete. 77 a) small plant of girth of exposed stem up to 75mm 78 providing and fixing soil waste and vent pipes : 79 110 mm dia upvc soil waste pipe conforming to is:13592 1992 (type-b) manufactured by supreme industries limited or equivalent. 80 erection of single layer bamboo-scaffolding made of average 75 mm dia bamboos with adequate bracing, ties, ropes etc. for strong, stable and workable scaffolding for specified jobs ( above gf beyound 4.00m height) like replacement of sewage/ rw pipes & accessories, repairs to plasters, special repairs, replacement of glass panes, uprooting/ cutting of tree saplings etc including dismantling the scaffolding after the job is done and clearing the site complete as per the direction of the engineer-in-charge. [ projected area of scaffolding frame work on buiding elevation to be measured for payment] 81 felling of trees like banyan, pipul etc from compound walls, building walls, cornices etc by making scaffolding where necessary including cutting of trunks and branches, application of chemicals/weedicides to the remaining portion to kill the growth of tree and ultimately removing the roots from the walls by cutting walls and mending good complete. ( the rate is inclusive of the mending good the walls with bricks/concretes/plasters and disposing of branches/trunks to vats inside compound for further disposal) 82 a) of girth above 30 cm upto 60 cm (measured above 1.0 m from gl toupto 5.0 m height) 83 extra for shifting of existing scaffolding by lifting/dragging or partially dismantling and re-erecting the dismantled portion in position (shifting at least 1.50 m from initial centre line of position) over payment for initial erection & dismantling paid in original item of scaffolding. [ projected area of scaffolding frame work on buiding elevation to be measured for payment] 84 providing and fixing ptmt health faucet with hook and p.v.c. pipe (1.00 metre minm length) of approved quality and colour in w.c.s all complete as per direction of engineer-in-charge. 85 15 mm nominal bore with minimum 1.00 m pvc tube. 86 attending repairs to ms gate by removing corroded portion of gate with welding machine at site and replacing with new members as per actual requirement at site. (cost for labour and hire charges of welding machine including transporation, consumables. steel members will be paid separately) 87 providing and welding 2mm thick m.s. sheet to existing m.s. frame work including providing and appying a priming coat of approved steel primer all complete. 88 providing and fixing upvc floor trap 100mm dia inlet and 100 mm dia outlet. 89 providing and fixing ptmt 2 way bib cock of approved quality and colour, for fixing hand faucet in commode toilets all complete as per direction in charge.- 15mm nominal bore. 90 supplying, fitting and fixing in position fibre glass panes of approved quality with resin, nail, clip etc. as per is:12866-1989. 91 4.0 mm thick (6.72 kg/sq.m) 92 credit value for dismantled unserviceable mild steel/ iron materials. 93 credit value for dismantled g.i. pipes: 94 15 mm nominal dia. 95 20 mm nominal dia. 96 25 mm nominal dia. 97 credit value for dismnatled c.i./ s.c.i. pipes. 98 credit value for unserviciable brass bib/stop cocks/pillar tap

Related Locations of : West Bengal

List of bore-work in howrah Tenders

Get Howrah Tender Alert...

Related Locations of : West Bengal

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us