Notice Inviting Tender (NIT) by the State Government Of Manipur for Construction Of Road At Mn08114 T15-Haokha Babu Bazar To Moijing Construction Of Job Pillers As Per Fig. 1600.1 D And Technical Specification Clause 1602.4 Surface Drains In Soil Construction Of Unlined Surface Drains Of Average Cross-Sectional Area 0.40 Sqm In Soil To Specified Lines, Grades, Levels And Dimensions. Excavated Material To Be Used In Embankment With A Lift Upto 3M And Lead Of 50 M Average Lead 25 M As Per Technical Specification Clause 307. A Manual Means Construction Of Embankment With Material Obtained From Borrow Pits Construction Of Embankment With Approved Material Obtained From Borrow Pits With A Lift Upto 1.5 M, Transporting To Site, Spreading, Grading To Required Slope And Compacting To Meet Requirement Of Tables 300.1 And 300.2 With A Lead Upto 1000 M As Per Technical Specification Clause 301.5 Construction Of Subgrade And Earthen Shoulders Construction Of Subgrade And Earthen Shoulders With Approved Material Obtained From Borrow Pits With All Lifts And Leads, Transporting To Site, Spreading, Grading To Required Slope And Compacted To Meet Requirement Of Table 300.2 With Lead Upto 1000 M As Per Technical Specification Clause 303.1. Compacting Original Ground Supporting Subgrade Loosening Of The Ground Upto A Level Of 300 Mm Below The Subgrade Level, Watered, Graded And Compacted In Layers To Meet Requirement Of Tables 300.1 And 300.2 For Subgrade Construction As Per Technical Specification Clause 303.5.2. Kilometre Stone Reinforced Cement Concrete M15 Grade Kilometre Stone/Local Stone Of Standard Design As Per Irc:8 Fixing In Position Including Painting And Printing, Etc As Per Drawing And Technical Specification Clause 1703 I Ordinary Kilometer Stone Precast Ii 200 M Stone Precast Providing And Fixing Logo Of Pmgsy Project Providing And Fixing Of Typical Pmgsy Informatory Sign Board With Logo As Per Mord Specifications And Drawing. Three Ms Plates Of 1.6 Mm Thick, Top And Middle Plate Duly Welded With Ms Flat Iron 25Mm X 5M Size On Back On Edges. The Lower Plate Will Be Welded With Ms Angle Iron Frame Of 25Mm X 25Mm X 5Mm. The Angle Iron Frame Of The Lower Most Plate And Flat Iron Frame Of Middle Plate Will Be Welded To 2 Nos. 75Mm X 75 Mm Of 12 Swg Sheet Tubes Posts Duly Embedded In Cement Concrete M-15 Grade Blocks Of 450Mm X 450Mm X 600Mm, 600Mm Below Ground Level. The Top Most Diamond Plate Will Be Welded To Middle Plate By 47Mm X 47Mm Of 12 Swg Steel Plate Tube. All M.S. Will Be Stove Enameled On Both Sides. Lettering And Printing Arrows, Border Etc. Will Be Painted With Ready Mixed Synthetic Enamel Paint Of Superior Quality In Required Shade And Colour. All Sections Of Framed Posts And Steel Tube Will Be Painted With Primer And Two Coats Of Epoxy Paint As Per Drawing Clause 1701 And Annexure 1700.1 Providing And Fixing Of Citizen Information Board Of Pmgsy Project Steel Tube Providing And Fixing Of Citizens Information Board For Pmgsy Project With Logo As Per Mord Specifications And Drawing. Two Ms Plates Of 1.6 Mm Thick, Top And Bottom Plate Duly Welded With Ms Flat Iron 25Mm X 5M Size On Back On Edges. The Plates Will Be Welded With Ms Angle Iron Frame Of 25Mm X 25Mm X 5Mm. The Angle Iron Frames Of The Plates Will Be Welded To 2 Nos. 75Mm X 75 Mm Of 12 Swg Sheet Tubes Posts Duly Embedded In Cement Concrete M-15 Grade Blocks Of 600Mm X 600Mm X 750Mm, 750Mm Below Ground Level. All M.S. Will Be Stove Enameled On Both Sides. Lettering And Printing Arrows, Border Etc. Will Be Painted With Ready Mixed Synthetic Enamel Paint Of Superior Quality In Required Shade And Colour. All Sections Of Framed Posts And Steel Tube Will Be Painted With Primer And Two Coats Of Epoxy Paint As Per Drawing Clause 1701 And Annexure 1700.1 Providing And Fixing Maintenance Information Board Of Pmgsy Project Providing And Fixing Of Maintenance Information Board For Pmgsy Project With Logo As Per Mord Specifications And Drawing. Two Ms Plates Of 1.6 Mm Thick, Top And Bottom Plate Duly Welded With Ms Flat Iron 25Mm X 5 Mm Size On Back On Edges. The Plates Will Be Welded With Ms Angle Iron Frame Of 25Mm X 25Mm X 5Mm. The Angle Iron Frame Of The Plates Will Be Welded To 2 Nos. 75Mm X 75Mm Of 12 Swg Sheet Tubes Posts Duly Embedded In Cement Concrete M-15 Grade Blocks Of 600Mm X 600Mm X 750Mm, 750Mm Below Ground Level. All M.S. Will Be Stove Enamelled On Both Sides. Lettering And Printing Arrows, Border Etc. Will Be Painted With Ready Mixed Synthetic Enamel Paint Of Superior Quality In Required Shade And Colour. All Sections Of Framed Posts And Steel Tube Will Be Painted With Primer And Two Coats Of Epoxy Paint As Per Drawing Clause 1701 And Annexure 1700.1 Traffic Signs/Retro-Reflectorised Traffic Signs Providing And Fixing Of Retro-Reflectorised Cautionary, Mandatory And Informatory Sign As Per Irc:67 Made Of Encapsulated Lens Type Reflective Sheeting Vide Clause 1701.2.3 Fixed Over Aluminium Sheeting, 1.5 Mm Thick Supported On A Mild Steel Angle Iron Post 75 Mm X 75 Mm X 6 Mm Firmly Fixed To The Ground By Means Of Properly Designed Foundation With M15 Grade Cement Concrete 450 Mm X 450 Mm X 600 Mm, 600 Mm Below Ground Level As Per Drawings And Technical Specification Clause 801. A 600 Mm Dia Circle B 600 Mm Equilateral Triangle Providing And Fixing Pmgsy Logo Board At Starting Point Steel Tube Providing And Fixing Of Typical Pmgsy Logo Board As Per Mord Specifications And Drawing. One Plate Of 1.6Mm Thick With Ms Flat 25Mm X 5Mm Size On Back On Centre. The Topmost Diamond Plate & Mid. Plate Will Be Welded To 75Mm X 75Mm 0F 12 Swg Steel Plate Tube Posts & Dully Embedded To Cc 450Mm X 450Mm X 600Mm Below Gl. Lettering And Printing Etc. Will Be With Ready Mixed Synthetic Enamel Paint Of Superior. Direction And Place Identification Signs Upto 0.90 Sqm Size Board A. Retro-Reflectorised Traffic Signs Providing And Erecting Direction And Place Identification Retro-Reflectorised Sheeting Vide Clasue 1701.2.3., Fixed Over Aluminium Sheeting 2Mm Thick With Area Not Exceeding 0.90 Sqm Supported On A Mild Steel Angle Iron Posts 75 X 75 X 6 Mm Firmly Fixed To The Gorund By Means Of Properly Designed Foundation With M-15 Grade Cement Concrete 450 X 450 X 600Mm, 600Mm Below Ground Level As Per Approved Drawing And Technical Specifications Clasuse 1701 Granular Sub-Base/Base/Surface Course With Local Materials Table 400.13 By Mix In Place Method Normal Construction Of Granular Sub-Base By Providing Local Material Spreading In Uniform Layers With Motor Grader On Prepared Surface, Mixing By Mix In Place Method With Rotavator At Once And Compacting With Smooth Wheel Roller To Achieve The Desired Density Complete As Per Clause 401.4 As Per Technical Specification Clause 408. I Using Naturally Occuring Gravel Wbm Grading 2 Providing, Laying, Spreading And Compacting Stone Aggregates Of Specific Sizes To Water Bound Macadam Specification Including Spreading In Uniform Thickness, Hand Packing, Rolling With Smooth Wheel Roller 80-100 Kn In Stages To Proper Grade And Camber, Applying And Brooming, Stone Screening/Binding Materials To Fill-Up The Interstices Of Coarse Aggregate, Watering And Compacting To The Required Density Grading 3 As Per Technical Specification Clause 405. A By Manual Means Wbm Grading 3 Providing, Laying, Spreading And Compacting Stone Aggregates Of Specific Sizes To Water Bound Macadam Specification Including Spreading In Uniform Thickness, Hand Packing, Rolling With Smooth Wheel Roller 80-100 Kn In Stages To Proper Grade And Camber, Applying And Brooming, Stone Screening/Binding Materials To Fill-Up The Interstices Of Coarse Aggregate, Watering And Compacting To The Required Density Grading 3 As Per Technical Specification Clause 405. A By Manual Means Prime Coat:Low Porosity Providing And Applying Primer Coat With Bitumen Emulsion Ss-1 On Prepared Surface Of Granular Base Including Cleaning Of Road Surface And Spraying Primer At The Rate Of 0.70-1.0 Kg/Sqm Using Mechanical Means As Per Technical Specification Clause 502.A By Manual Means Tack Coat Providing And Applying Tack Coat With Bitumen Emulsion Rs-1 Using Emulsion Distributor At The Rate Of 0.25 To 0.30 Kg Per Sqm On The Prepared Bituminous Surface Cleaned With Hydraulic Broom As Per Technical Specification Clause 503. A By Manual Means 20Mm Thick Open-Graded Premix Carpet Using Bituminous Penetration Grade/Modified Bitumen Binder Providing, Laying And Rolling Of Open-Graded Premix Carpet Of 20 Mm Thickness Composed Of 13.2 Mm To 5.6 Mm Aggregates Either Using Penetration Grade Bitumen Or Emulsion To Required Line, Grade And Level To Serve As Wearing Course On A Previously Prepared Base, Including Mixing In A Suitable Plant, Laying And Rolling With A Three Wheel 80-100 Kn Static Roller Capacity, Finished To Required Level And Grades To Be Followed By Seal Coat Of Either Type A Or Type B Or Type C As Per Technical Specification Clause 508. Using Plastic Waste Case-I By Manual Means I Bitumens-90 Seal Coat Providing And Laying Seal Coat Sealing The Voids In A Bituminous Surface Laid To The Specified Levels, Grade And Cross Fall Using Type A, Type B And Type C As Per Technical Specification Clause 510. Case Ii : Type B By Manual Meansi Bitumens-90 Construction Of 1.50 M Span Rcc Slab Culvert 4.63Ht.3Nos Excavation For Structures Earthwork In Excavation For Structures As Per Drawing And Technical Specifications Clause 305.1 Including Setting Out, Construction Of Shoring And Bracing, Removal Of Stumps And Other Deleterious Material And Disposal Upto A Lead Of 50M, Dressing Of Sides And Bottom And Backfilling In Trenches With Excavated Suitable Material. I Ordinary Soil I Upto 3M Depth. Providing Concrete For Plain/ Reinforced Concrete In Open Foundation Complete As Per Drawings And Technical Specifications Clause 802, 803, 1202 &1203 Ipcc Grade M 10, I Nominal Mix. 1:3:6 Plain/Reinforced Cement Concrete In Substructure Complete As Per Drawings And Technical Specification Clauses 802, 804, 805, 806, 807, 1202 Ans 1204 I Pcc M 15 I Nominal Mix 1:2.5:5 Providing And Laying Reinforced Cement Concrete In Superstructure As Per Drawing And Technical Specifications Clauses 800, 1205.4 And 1205.5 Ii. Rcc Grade M 25 Supplying, Fitting, And Placing Hysd Bar Reinforcement In Superstructure Complete As Per Drawing And Technical Specifications Clauses 1002, 1010 And 1202 Providing Weepholes In Brick Masonry/Stone Masonry, Plain/Reinforced Concrete Abutment, Wing Wall, Return Wall With 100 Mm Dia Ac Pipe Extending Through The Full Width Of The Structures With Slope Of 1V:20H Towards Drawing Face Complete As Per Drawing And Technical Specification Clauses 614, 709, 1204.3.7 Providing And Laying Filter Media With Granular Crushed Aggregates As Per Specification To A Thickness Of Not Less Than 600 Mm With Smaller Size Towards The Soil And Bigger Size Towards The Wall And Providing Over The Entire Surface Behind Abutment, Wing Wall, Return Wall To The Full Height, Compacted To Firm Condition Complete As Per Drawing And Technical Specification Clause 1204.3.8 Construction Of Retaining Wall : Height 4 M5nos Excavation For Structures Earthwork In Excavation For Structures As Per Drawing And Technical Specifications Clause 305.1 Including Setting Out, Construction Of Shoring And Bracing, Removal Of Stumps And Other Deleterious Material And Disposal Upto A Lead Of 50M, Dressing Of Sides And Bottom And Backfilling In Trenches With Excavated Suitable Material I Ordinary Soil I Upto 3M Depth Providing Concrete For Plain/ Reinforced Concrete In Open Foundation Complete As Per Drawings And Technical Specifications Clause 802, 803, 1202 &1203 Ipcc Grade M 10, I Nominal Mix. 1:3:6 Stone Masonry In Cement Mortar For Substructure Complete As Per Drawing & Technical Specification Clauses 702, 704, 1202 And 1204 Iii Random Rubble Masonry Ii In 1:4 Cement Mortar Providing Weepholes In Brick Masonry/Stone Masonry, Plain/Reinforced Concrete Abutment, Wing Wall, Return Wall With 100 Mm Dia Ac Pipe Extending Through The Full Width Of The Structures With Slope Of 1V:20H Towards Drawing Face Complete As Per Drawing And Technical Specification Clauses 614, 709, 1204.3.7 Providing And Laying Filter Media With Granular Crushed Aggregates As Per Specification To A Thickness Of Not Less Than 600 Mm With Smaller Size Towards The Soil And Bigger Size Towards The Wall And Providing Over The Entire Surface Behind Abutment, Wing Wall, Return Wall To The Full Height, Compacted To Firm Condition Complete As Per Drawing And Technical Specification Clause 1204.3.8 Pointing With Cement Mortar 1:3 On Brickwork As Per Drawing And Technical Sepecification Clauses 613.3 And 1204 Maintenance Component For 5Five Years After Construction Not To Be Quoted Yearwise in Thoubal - Manipur has been published.
The last date of this tender is 06/10/2020, work value is  32090000 INR, EMD is  642000 INR and tender document fees is  20000 INR
For more details call us on +91 92760 83333 for bidding support this tender, GeM, vendor registration (if any) and tender BOQ documents.