Filters

List of latest Quality-Control Tenders in Indian Tenders. Click on any Quality-Control Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for Quality-Control Tenders.

All-Tenders (77)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

State Government

TRN :24670543 | 27 Jun, 2022

Tender Value : 3.89 Crore

Hilsa - Bihar

Tender for civil work - jagoi khusalpur road to nishanpura, clearing and grubbing road land by manual means including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300mm, removals of stumps of such trees cut earlier & disposal of unserviceable materials & stacking of serviceable materials to be used or auctioned upto a lead of 1000 m including removal and disposal of top organic soil not exeeding 150mm in thickness as per technical specification clause 201.1 and direction of e/i, construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table 300.2 with lead upto 1000 m as per technical specification clause 303.1., providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm type-a or 13.2 mm to 0.9 mm type-b aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kn static roller and finishing to required level and grades as per technical specification clause 509., providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of0.30 to 0.35 kg per sqm on the prepared granular surface tretaed with primer and clened with hydriloc broom as per technical specification aclouse 503., providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surface tretaed with primer and clened with hydriloc broom as per technical specification aclouse 503., providing and laying semi dense bituminous concrete with 100-120 tph batch type hmp producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per morth specification clause no. 508 complete in all respects., kilometre stone, reinforced cement concrete m15 grade kilometre local stone of standard design asper irc:8 fixing in position including painting and printing, etc as per drawing and technical specification clause 1703., ii km stone, iii 200 m stone, retro-reflectorised traffic signsproviding and erecting direction and place identification retro-\reflectorised sign as per irc:67 made of encapsulated lens type reflective sheeting vide clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on mild steel angle iron posts 75 mm x 75 mm x 6 mm, 2 nos. firmly fixed to the ground by means of properly designed foundation with m-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and technical specification clause 1701., providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per irc:67 made of encapsulated lens type reflective sheeting vide clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with m15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and technical specification clause 801, 600 mm equilateral & triangle, 600 mm circular, 600 mm x 450 mm rectangular, 900 mm side octagon, reinforced cement concrete m15 grade boundary pillars/local stone of standard design as per irc:25, fixed in position including finishing and lettering but excluding painting as per drawing and technical specification clause 1704, printing new letter and figures of any shade with synthetic enamel paint black or any other approved colour to give an even shade as per drawings and technical specification clause 1701, providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per irc:35 .the finished surface to be level, uniform and free from streaks and holes., at edge for bt portion, pedestrian crossing2 m in length and providing at 50 cm apart, providing and fixing of typical mmgsy informatory sign board with logo as per mord specifications and drawing. three ms plates of 1.6 mm thick, top and middle plate duly welded with ms flat iron 25mm x 5m size on back on edges. the lower plate will be welded with ms angle iron frame of 25mm x 25mm x 5mm. the angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 swg sheet tubes posts duly embedded in cement concrete m-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. the top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 swg steel plate tube. all m.s. will be stove enameled on both sides. lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. all sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing clause 1701 and annexure 1700.1, painting on parapet wall black & white strips painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and technical specification clause 1701, plastering with cement mortar 1:4 on brick work in sub-structure as per technical specifications, brick masonry work in cement mortar 1:3 in parapet excluding pointing and plastering as per drawing and technical specifications clauses 600, 900 and 1208.4, 300mm irrigation pipe, providing and laying of a reinforced cement concrete pipe duct, 300 mm dia, across the road new construction, extending from drain to drain in cuts and toe of slope to toe of slope in fills, constructing head walls at both ends, providing a minimum fill of granular material over top and sides of rcc pipe as per irc:981997, bedded on a 0.3 m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe, subject to minimum 450 mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per irc: 98 - 1997 and approved drawings., , 12 % gst, 1% labour cess, seigniorage fee, 5 year maintenance cost, 12 % gst, 1% labour cess, seigniorage fee, gomhar auangari road to sultanpur, clearing and grubbing road land by manual means including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300mm, removals of stumps of such trees cut earlier & disposal of unserviceable materials & stacking of serviceable materials to be used or auctioned upto a lead of 1000 m including removal and disposal of top organic soil not exeeding 150mm in thickness as per technical specification clause 201.1 and direction of e/i, construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table 300.2 with lead upto 1000 m as per technical specification clause 303.1., granular sub-base with well graded materialgrade 2 : construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with smooth wheel roller to achieve the desired density, complete as per technical specification clause 401., water bound macadam with stone screening gr-ii : providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kn static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 2 as per technical specification clause 405., water bound macadam gr iii : providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kn in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per technical specification clause 405., providing and applying primer coat with bitumen emulsion ss-1 on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70- 1.0 kg/sqm using mechanical means as per technical specification clause 502., providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm type-a or 13.2 mm to 0.9 mm type-b aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kn static roller and finishing to required level and grades as per technical specification clause 509., providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared granular surface tretaed with primer and clened with hydriloc broom as per technical specification aclouse 503., providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surface tretaed with primer and clened with hydriloc broom as per technical specification aclouse 503., providing and laying semi dense bituminous concrete with 100-120 tph batch type hmp producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per morth specification clause no. 508 complete in all respects., construction of un-reinforcedplain cement thickness as perdesign, over a prepared sub base with 43 grade cement or any other type as per clause 1501.2.2 m 30 grade coarse and fine aggregate maximum size of aggregate not exceding 25mm, mixed in a concrete of not less than 0.2cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork steel channel, laying and fixing of 125 micron thick plythene film, wedges, steel plates including levelling the formwork as per drawing spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, constrution joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/ culvert and construction joints, admixtures as approved, curing of concrete slab for 14 days curing compound where specified and water finishing to lines and grade as per drawing and technical specification clause 1501., kilometre stone, reinforced cement concrete m15 grade kilometre local stone of standard design asper irc:8 fixing in position including painting and printing, etc as per drawing and technical specification clause 1703., ii km stone, iii 200 m stone, retro-reflectorised traffic signsproviding and erecting direction and place identification retro-\reflectorised sign as per irc:67 made of encapsulated lens type reflective sheeting vide clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on mild steel angle iron posts 75 mm x 75 mm x 6 mm, 2 nos. firmly fixed to the ground by means of properly designed foundation with m-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and technical specification clause 1701., providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per irc:67 made of encapsulated lens type reflective sheeting vide clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with m15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and technical specification clause 801, 600 mm equilateral & triangle, 600 mm circular, 600 mm x 450 mm rectangular, 900 mm side octagon, reinforced cement concrete m15 grade boundary pillars/local stone of standard design as per irc:25, fixed in position including finishing and lettering but excluding painting as per drawing and technical specification clause 1704, printing new letter and figures of any shade with synthetic enamel paint black or any other approved colour to give an even shade as per drawings and technical specification clause 1701, planting of trees by the road side avenue trees in 0.60 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge manure, planting the saplings, backfilling the trench, watering, fixing the tree guard and maintaining the plants for one year, providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per irc:35 .the finished surface to be level, uniform and free from streaks and holes., at edge for bt portion, pedestrian crossing2 m in length and providing at 50 cm apart, at edge for old cc portion, providing and fixing of typical mmgsy informatory sign board with logo as per mord specifications and drawing. three ms plates of 1.6 mm thick, top and middle plate duly welded with ms flat iron 25mm x 5m size on back on edges. the lower plate will be welded with ms angle iron frame of 25mm x 25mm x 5mm. the angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 swg sheet tubes posts duly embedded in cement concrete m-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. the top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 swg steel plate tube. all m.s. will be stove enameled on both sides. lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. all sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing clause 1701 and annexure 1700.1, painting on parapet wall black & white strips painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and technical specification clause 1701, plastering with cement mortar 1:4 on brick work in sub-structure as per technical specifications, brick masonry work in cement mortar 1:3 in parapet excluding pointing and plastering as per drawing and technical specifications clauses 600, 900 and 1208.4, 300mm irrigation pipe, providing and laying of a reinforced cement concrete pipe duct, 300 mm dia, across the road new construction, extending from drain to drain in cuts and toe of slope to toe of slope in fills, constructing head walls at both ends, providing a minimum fill of granular material over top and sides of rcc pipe as per irc:981997, bedded on a 0.3 m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe, subject to minimum 450 mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per irc: 98 - 1997 and approved drawings., , 12 % gst, 1% labour cess, seigniorage fee, 5 year maintenance cost, 12 % gst, 1% labour cess, seigniorage fee, ekangar islampur road to gomhar, clearing and grubbing road land by manual means including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300mm, removals of stumps of such trees cut earlier & disposal of unserviceable materials & stacking of serviceable materials to be used or auctioned upto a lead of 1000 m including removal and disposal of top organic soil not exeeding 150mm in thickness as per technical specification clause 201.1 and direction of e/i, construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table 300.2 with lead upto 1000 m as per technical specification clause 303.1., granular sub-base with well graded materialgrade 2 : construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with smooth wheel roller to achieve the desired density, complete as per technical specification clause 401., water bound macadam with stone screening gr-ii : providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kn static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 2 as per technical specification clause 405., water bound macadam gr iii : providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kn in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per technical specification clause 405., providing and applying primer coat with bitumen emulsion ss-1 on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70- 1.0 kg/sqm using mechanical means as per technical specification clause 502., providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm type-a or 13.2 mm to 0.9 mm type-b aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kn static roller and finishing to required level and grades as per technical specification clause 509., providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared granular surface tretaed with primer and clened with hydriloc broom as per technical specification aclouse 503., providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared granular surface tretaed with primer and clened with hydriloc broom as per technical specification aclouse 503., providing and laying semi dense bituminous concrete with 100-120 tph batch type hmp producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per morth specification clause no. 508 complete in all respects., kilometre stone, reinforced cement concrete m15 grade kilometre local stone of standard design asper irc:8 fixing in position including painting and printing, etc as per drawing and technical specification clause 1703., i km stone, ii 200 m stone, retro-reflectorised traffic signsproviding and erecting direction and place identification retro-\reflectorised sign as per irc:67 made of encapsulated lens type reflective sheeting vide clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on mild steel angle iron posts 75 mm x 75 mm x 6 mm, 2 nos. firmly fixed to the ground by means of properly designed foundation with m-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and technical specification clause 1701., providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per irc:67 made of encapsulated lens type reflective sheeting vide clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with m15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and technical specification clause 801, 600 mm equilateral & triangle, 600 mm circular, 600 mm x 450 mm rectangular, 900 mm side octagon, reinforced cement concrete m15 grade boundary pillars/local stone of standard design as per irc:25, fixed in position including finishing and lettering but excluding painting as per drawing and technical specification clause 1704, printing new letter and figures of any shade with synthetic enamel paint black or any other approved colour to give an even shade as per drawings and technical specification clause 1701, planting of trees by the road side avenue trees in 0.60 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge manure, planting the saplings, backfilling the trench, watering, fixing the tree guard and maintaining the plants for one year, providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per irc:35 .the finished surface to be level, uniform and free from streaks and holes., at edge for bt portion, pedestrian crossing2 m in length and providing at 50 cm apart, providing and fixing of typical mmgsy informatory sign board with logo as per mord specifications and drawing. three ms plates of 1.6 mm thick, top and middle plate duly welded with ms flat iron 25mm x 5m size on back on edges. the lower plate will be welded with ms angle iron frame of 25mm x 25mm x 5mm. the angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 swg sheet tubes posts duly embedded in cement concrete m-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. the top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 swg steel plate tube. all m.s. will be stove enameled on both sides. lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. all sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing clause 1701 and annexure 1700.1, cross drainage works/protection/repair, brick masonry work in cement mortar 1:3 in parapet excluding pointing and plastering as per drawing and technical specifications clauses 600, 900 and 1208.4, plastering with cement mortar 1:4 on brick work in sub-structure as per technical specifications, painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and technical specification clause 1701, 300mm irrigation pipe, providing and laying of a reinforced cement concrete pipe duct, 300 mm dia, across the road new construction, extending from drain to drain in cuts and toe of slope to toe of slope in fills, constructing head walls at both ends, providing a minimum fill of granular material over top and sides of rcc pipe as per irc:981997, bedded on a 0.3 m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe, subject to minimum 450 mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per irc: 98 - 1997 and approved drawings., , 12 % gst, 1% labour cess, seigniorage fee, 5 year maintenance cost, 12 % gst, 1% labour cess, seigniorage fee, t05 to baidrabad, clearing and grubbing road land by manual means including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300mm, removals of stumps of such trees cut earlier & disposal of unserviceable materials & stacking of serviceable materials to be used or auctioned upto a lead of 1000 m including removal and disposal of top organic soil not exeeding 150mm in thickness as per technical specification clause 201.1 and direction of e/i, construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table 300.2 with lead upto 1000 m as per technical specification clause 303.1., granular sub-base with well graded materialgrade 2 : construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with smooth wheel roller to achieve the desired density, complete as per technical specification clause 401., water bound macadam with stone screening gr-ii : providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kn static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 2 as per technical specification clause 405., water bound macadam gr iii : providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kn in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per technical specification clause 405., providing and applying primer coat with bitumen emulsion ss-1 on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70- 1.0 kg/sqm using mechanical means as per technical specification clause 502., providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm type-a or 13.2 mm to 0.9 mm type-b aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kn static roller and finishing to required level and grades as per technical specification clause 509., providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bitumen surface tretaed with primer and clened with hydriloc broom as per technical specification aclouse 503., providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surface tretaed with primer and clened with hydriloc broom as per technical specification aclouse 503., providing and laying semi dense bituminous concrete with 100-120 tph batch type hmp producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per morth specification clause no. 508 complete in all respects., construction of un-reinforcedplain cement thickness as perdesign, over a prepared sub base with 43 grade cement or any other type as per clause 1501.2.2 m 30 grade coarse and fine aggregate maximum size of aggregate not exceding 25mm, mixed in a concrete of not less than 0.2cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork steel channel, laying and fixing of 125 micron thick plythene film, wedges, steel plates including levelling the formwork as per drawing spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, constrution joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/ culvert and construction joints, admixtures as approved, curing of concrete slab for 14 days curing compound where specified and water finishing to lines and grade as per drawing and technical specification clause 1501., kilometre stone, reinforced cement concrete m15 grade kilometre local stone of standard design asper irc:8 fixing in position including painting and printing, etc as per drawing and technical specification clause 1703., ii km stone, iii 200 m stone, retro-reflectorised traffic signsproviding and erecting direction and place identification retro-\reflectorised sign as per irc:67 made of encapsulated lens type reflective sheeting vide clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on mild steel angle iron posts 75 mm x 75 mm x 6 mm, 2 nos. firmly fixed to the ground by means of properly designed foundation with m-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and technical specification clause 1701, and etc.

State Government

TRN :24670594 | 27 Jun, 2022

Tender Value : 5.33 Crore

Hilsa - Bihar

Tender for civil work - l026-l025 to serifabad, clearing and grubbing road land by manual means including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300mm, removals of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable materials to be used or auctioned upto a lead of 1000 m including removal and disposal of top organic soil not exeeding 150mm in thickness as per technical specification clause 201.1 and direction of e/i, construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table 300.2 with lead upto 1000 m as per technical specification clause 303.1., granular sub-base with well graded materialgrade 2 : construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with smooth wheel roller to achieve the desired density, complete as per technical specification clause 401., water bound macadam with stone screening gr-ii : providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kn static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 2 as per technical specification clause 405., water bound macadam gr iii : providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kn in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per technical specification clause 405., providing and applying primer coat with bitumen emulsion ss-1 on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70- 1.0 kg/sqm using mechanical means as per technical specification clause 502., providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm type-a or 13.2 mm to 0.9 mm type-b aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kn static roller and finishing to required level and grades as per technical specification clause 509., providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bitumen surface tretaed with primer and clened with hydriloc broom as per technical specification aclouse 503., providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surface tretaed with primer and clened with hydriloc broom as per technical specification aclouse 503., providing and laying semi dense bituminous concrete with 100-120 tph batch type hmp producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per morth specification clause no. 508 complete in all respects., construction of un-reinforcedplain cement thickness as perdesign, over a prepared sub base with 43 grade cement or any other type as per clause 1501.2.2 m 30 grade coarse and fine aggregate maximum size of aggregate not exceding 25mm, mixed in a concrete of not less than 0.2cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork steel channel, laying and fixing of 125 micron thick plythene film, wedges, steel plates including levelling the formwork as per drawing spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, constrution joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/ culvert and construction joints, admixtures as approved, curing of concrete slab for 14 days curing compound where specified and water finishing to lines and grade as per drawing and technical specification clause 1501., kilometre stone, reinforced cement concrete m15 grade kilometre local stone of standard design asper irc:8 fixing in position including painting and printing, etc as per drawing and technical specification clause 1703., i 5th km stone, ii km stone, iii 200 m stone, retro-reflectorised traffic signsproviding and erecting direction and place identification retro-\reflectorised sign as per irc:67 made of encapsulated lens type reflective sheeting vide clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on mild steel angle iron posts 75 mm x 75 mm x 6 mm, 2 nos. firmly fixed to the ground by means of properly designed foundation with m-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and technical specification clause 1701., providing and erecting a w metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ismc series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to is:1367 and is:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per clause 810, providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per irc:67 made of encapsulated lens type reflective sheeting vide clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with m15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and technical specification clause 801, 600 mm equilateral & triangle, 600 mm circular, 600 mm x 450 mm rectangular, 900 mm side octagon, reinforced cement concrete m15 grade boundary pillars/local stone of standard design as per irc:25, fixed in position including finishing and lettering but excluding painting as per drawing and technical specification clause 1704, printing new letter and figures of any shade with synthetic enamel paint black or any other approved colour to give an even shade as per drawings and technical specification clause 1701, planting of trees by the road side avenue trees in 0.60 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge manure, planting the saplings, backfilling the trench, watering, fixing the tree guard and maintaining the plants for one year, providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per irc:35 .the finished surface to be level, uniform and free from streaks and holes., at edge for bt portion, pedestrian crossing2 m in length and providing at 50 cm apart, at edge for old cc portion, providing and fixing of typical mmgsy informatory sign board with logo as per mord specifications and drawing. three ms plates of 1.6 mm thick, top and middle plate duly welded with ms flat iron 25mm x 5m size on back on edges. the lower plate will be welded with ms angle iron frame of 25mm x 25mm x 5mm. the angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 swg sheet tubes posts duly embedded in cement concrete m-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. the top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 swg steel plate tube. all m.s. will be stove enameled on both sides. lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. all sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing clause 1701 and annexure 1700.1, cross drainage works/protection/repair, painting on parapet wall black & white strips painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and technical specification clause 1701, plastering with cement mortar 1:4 on brick work in sub-structure as per technical specifications, brick masonry work in cement mortar 1:3 in parapet excluding pointing and plastering as per drawing and technical specifications clauses 600, 900 and 1208.4, 300mm irrigation pipe, providing and laying of a reinforced cement concrete pipe duct, 300 mm dia, across the road new construction, extending from drain to drain in cuts and toe of slope to toe of slope in fills, constructing head walls at both ends, providing a minimum fill of granular material over top and sides of rcc pipe as per irc:981997, bedded on a 0.3 m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe, subject to minimum 450 mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per irc: 98 - 1997 and approved drawings., , 12 % gst, 1% labour cess, seigniorage fee, 5 year maintenance cost, 12 % gst, 1% labour cess, seigniorage fee, islampur-herthu, clearing and grubbing road land by manual means including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300mm, removals of stumps of such trees cut earlier & disposal of unserviceable materials & stacking of serviceable materials to be used or auctioned upto a lead of 1000 m including removal and disposal of top organic soil not exeeding 150mm in thickness as per technical specification clause 201.1 and direction of e/i, construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table 300.2 with lead upto 1000 m as per technical specification clause 303.1., granular sub-base with well graded materialgrade 2 : construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with smooth wheel roller to achieve the desired density, complete as per technical specification clause 401., water bound macadam with stone screening gr-ii : providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kn static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 2 as per technical specification clause 405., water bound macadam gr iii : providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kn in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per technical specification clause 405., providing and applying primer coat with bitumen emulsion ss-1 on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70- 1.0 kg/sqm using mechanical means as per technical specification clause 502., providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm type-a or 13.2 mm to 0.9 mm type-b aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kn static roller and finishing to required level and grades as per technical specification clause 509., providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared granular surface tretaed with primer and clened with hydriloc broom as per technical specification aclouse 503., providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surface tretaed with primer and clened with hydriloc broom as per technical specification aclouse 503., providing and laying semi dense bituminous concrete with 100-120 tph batch type hmp producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per morth specification clause no. 508 complete in all respects., construction of un-reinforcedplain cement thickness as perdesign, over a prepared sub base with 43 grade cement or any other type as per clause 1501.2.2 m 30 grade coarse and fine aggregate maximum size of aggregate not exceding 25mm, mixed in a concrete of not less than 0.2cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork steel channel, laying and fixing of 125 micron thick plythene film, wedges, steel plates including levelling the formwork as per drawing spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, constrution joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/ culvert and construction joints, admixtures as approved, curing of concrete slab for 14 days curing compound where specified and water finishing to lines and grade as per drawing and technical specification clause 1501., kilometre stone, reinforced cement concrete m15 grade kilometre local stone of standard design asper irc:8 fixing in position including painting and printing, etc as per drawing and technical specification clause 1703., ii km stone, iii 200 m stone, retro-reflectorised traffic signsproviding and erecting direction and place identification retro-\reflectorised sign as per irc:67 made of encapsulated lens type reflective sheeting vide clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on mild steel angle iron posts 75 mm x 75 mm x 6 mm, 2 nos. firmly fixed to the ground by means of properly designed foundation with m-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and technical specification clause 1701., providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per irc:67 made of encapsulated lens type reflective sheeting vide clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with m15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and technical specification clause 801, 600 mm equilateral & triangle, 600 mm circular, 600 mm x 450 mm rectangular, 900 mm side octagon, reinforced cement concrete m15 grade boundary pillars/local stone of standard design as per irc:25, fixed in position including finishing and lettering but excluding painting as per drawing and technical specification clause 1704, printing new letter and figures of any shade with synthetic enamel paint black or any other approved colour to give an even shade as per drawings and technical specification clause 1701, planting of trees by the road side avenue trees in 0.60 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge manure, planting the saplings, backfilling the trench, watering, fixing the tree guard and maintaining the plants for one year, providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per irc:35 .the finished surface to be level, uniform and free from streaks and holes., at edge for bt portion, pedestrian crossing2 m in length and providing at 50 cm apart, at edge for old cc portion, providing and fixing of typical mmgsy informatory sign board with logo as per mord specifications and drawing. three ms plates of 1.6 mm thick, top and middle plate duly welded with ms flat iron 25mm x 5m size on back on edges. the lower plate will be welded with ms angle iron frame of 25mm x 25mm x 5mm. the angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 swg sheet tubes posts duly embedded in cement concrete m-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. the top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 swg steel plate tube. all m.s. will be stove enameled on both sides. lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. all sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing clause 1701 and annexure 1700.1, painting on parapet wall black & white strips painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and technical specification clause 1701, plastering with cement mortar 1:4 on brick work in sub-structure as per technical specifications, brick masonry work in cement mortar 1:3 in parapet excluding pointing and plastering as per drawing and technical specifications clauses 600, 900 and 1208.4, 300mm irrigation pipe, providing and laying of a reinforced cement concrete pipe duct, 300 mm dia, across the road new construction, extending from drain to drain in cuts and toe of slope to toe of slope in fills, constructing head walls at both ends, providing a minimum fill of granular material over top and sides of rcc pipe as per irc:981997, bedded on a 0.3 m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe, subject to minimum 450 mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per irc: 98 - 1997 and approved drawings., , 12 % gst, 1% labour cess, seigniorage fee, 5 year maintenance cost, 12 % gst, 1% labour cess, seigniorage fee, ramanujbag to chandorganti, clearing and grubbing road land by manual means including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300mm, removals of stumps of such trees cut earlier & disposal of unserviceable materials & stacking of serviceable materials to be used or auctioned upto a lead of 1000 m including removal and disposal of top organic soil not exeeding 150mm in thickness as per technical specification clause 201.1 and direction of e/i, construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table 300.2 with lead upto 1000 m as per technical specification clause 303.1., granular sub-base with well graded materialgrade 2 : construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with smooth wheel roller to achieve the desired density, complete as per technical specification clause 401., water bound macadam with stone screening gr-ii : providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kn static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 2 as per technical specification clause 405., water bound macadam gr iii : providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kn in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per technical specification clause 405., providing and applying primer coat with bitumen emulsion ss-1 on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70- 1.0 kg/sqm using mechanical means as per technical specification clause 502., providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm type-a or 13.2 mm to 0.9 mm type-b aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kn static roller and finishing to required level and grades as per technical specification clause 509., providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surface tretaed with primer and clened with hydriloc broom as per technical specification aclouse 503., providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surface tretaed with primer and clened with hydriloc broom as per technical specification aclouse 503., providing and laying semi dense bituminous concrete with 100-120 tph batch type hmp producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per morth specification clause no. 508 complete in all respects., kilometre stone, reinforced cement concrete m15 grade kilometre local stone of standard design asper irc:8 fixing in position including painting and printing, etc as per drawing and technical specification clause 1703., i km stone, ii 200 m stone, retro-reflectorised traffic signsproviding and erecting direction and place identification retro-\reflectorised sign as per irc:67 made of encapsulated lens type reflective sheeting vide clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on mild steel angle iron posts 75 mm x 75 mm x 6 mm, 2 nos. firmly fixed to the ground by means of properly designed foundation with m-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and technical specification clause 1701., providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per irc:67 made of encapsulated lens type reflective sheeting vide clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with m15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and technical specification clause 801, 600 mm equilateral & triangle, 600 mm circular, 600 mm x 450 mm rectangular, 900 mm side octagon, reinforced cement concrete m15 grade boundary pillars/local stone of standard design as per irc:25, fixed in position including finishing and lettering but excluding painting as per drawing and technical specification clause 1704, printing new letter and figures of any shade with synthetic enamel paint black or any other approved colour to give an even shade as per drawings and technical specification clause 1701, planting of trees by the road side avenue trees in 0.60 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge manure, planting the saplings, backfilling the trench, watering, fixing the tree guard and maintaining the plants for one year, providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per irc:35 .the finished surface to be level, uniform and free from streaks and holes., at edge for bt portion, pedestrian crossing2 m in length and providing at 50 cm apart, providing and fixing of typical mmgsy informatory sign board with logo as per mord specifications and drawing. three ms plates of 1.6 mm thick, top and middle plate duly welded with ms flat iron 25mm x 5m size on back on edges. the lower plate will be welded with ms angle iron frame of 25mm x 25mm x 5mm. the angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 swg sheet tubes posts duly embedded in cement concrete m-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. the top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 swg steel plate tube. all m.s. will be stove enameled on both sides. lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. all sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing clause 1701 and annexure 1700.1, cross drainage works/protection/repair, brick masonry work in cement mortar 1:3 in parapet excluding pointing and plastering as per drawing and technical specifications clauses 600, 900 and 1208.4, plastering with cement mortar 1:4 on brick work in sub-structure as per technical specifications, painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and technical specification clause 1701, 300mm irrigation pipe, providing and laying of a reinforced cement concrete pipe duct, 300 mm dia, across the road new construction, extending from drain to drain in cuts and toe of slope to toe of slope in fills, constructing head walls at both ends, providing a minimum fill of granular material over top and sides of rcc pipe as per irc:981997, bedded on a 0.3 m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe, subject to minimum 450 mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per irc: 98 - 1997 and approved drawings., , 12 % gst, 1% labour cess, seigniorage fee, 5 year maintenance cost, 12 % gst, 1% labour cess, seigniorage fee, harsiniya to gulab nagar, clearing and grubbing road land by manual means including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300mm, removals of stumps of such trees cut earlier & disposal of unserviceable materials & stacking of serviceable materials to be used or auctioned upto a lead of 1000 m including removal and disposal of top organic soil not exeeding 150mm in thickness as per technical specification clause 201.1 and direction of e/i, construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table 300.2 with lead upto 1000 m as per technical specification clause 303.1., granular sub-base with well graded materialgrade 2 : construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with smooth wheel roller to achieve the desired density, complete as per technical specification clause 401., water bound macadam with stone screening gr-ii : providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kn static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 2 as per technical specification clause 405., water bound macadam gr iii : providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kn in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per technical specification clause 405., providing and applying primer coat with bitumen emulsion ss-1 on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70- 1.0 kg/sqm using mechanical means as per technical specification clause 502., providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm type-a or 13.2 mm to 0.9 mm type-b aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kn static roller and finishing to required level and grades as per technical specification clause 509., providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.2 to 0.25 kg per sqm on the prepared granular surface tretaed with primer and clened with hydriloc broom as per technical specification aclouse 503., providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.2 to 0.25 kg per sqm on the prepared granular surface tretaed with primer and clened with hydriloc broom as per technical specification aclouse 503., providing and laying semi dense bituminous concrete with 100-120 tph batch type hmp producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic

State Government

TRN :24670644 | 27 Jun, 2022

Tender Value : 2.52 Crore

Hilsa - Bihar

Tender for civil works - t09 se vara bigha tak, clearing and grubbing road land by manual means including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300mm, removals of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable materials to be used or auctioned upto a lead of 1000 m including removal and disposal of top organic soil not exeeding 150mm in thickness as per technical specification clause 201.1 and direction of e/i, construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table 300.2 with lead upto 1000 m as per technical specification clause 303.1., granular sub-base with well graded materialgrade 2 : construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with smooth wheel roller to achieve the desired density, complete as per technical specification clause 401., water bound macadam with stone screening gr-ii : providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kn static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 2 as per technical specification clause 405., water bound macadam gr iii : providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kn in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per technical specification clause 405., providing and applying primer coat with bitumen emulsion ss-1 on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70- 1.0 kg/sqm using mechanical means as per technical specification clause 502., providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm type-a or 13.2 mm to 0.9 mm type-b aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kn static roller and finishing to required level and grades as per technical specification clause 509., providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surface tretaed with primer and clened with hydriloc broom as per technical specification aclouse 503., tackcoat 0.2-0.25 kg/m2 on bituminous surface, providing and laying semi dense bituminous concrete with 100-120 tph batch type hmp producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per morth specification clause no. 508 complete in all respects., construction of un-reinforcedplain cement thickness as perdesign, over a prepared sub base with 43 grade cement or any other type as per clause 1501.2.2 m 30 grade coarse and fine aggregate maximum size of aggregate not exceding 25mm, mixed in a concrete of not less than 0.2cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork steel channel, laying and fixing of 125 micron thick plythene film, wedges, steel plates including levelling the formwork as per drawing spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, constrution joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/ culvert and construction joints, admixtures as approved, curing of concrete slab for 14 days curing compound where specified and water finishing to lines and grade as per drawing and technical specification clause 1501., i 5th km stone, ii km stone, iii 200 m stone, retro-reflectorised traffic signsproviding and erecting direction and place identification retro-\reflectorised sign as per irc:67 made of encapsulated lens type reflective sheeting vide clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on mild steel angle iron posts 75 mm x 75 mm x 6 mm, 2 nos. firmly fixed to the ground by means of properly designed foundation with m-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and technical specification clause 1701., 600 mm equilateral & triangle, 600 mm circular, 600 mm x 450 mm rectangular, 900 mm side octagon, reinforced cement concrete m15 grade boundary pillars/local stone of standard design as per irc:25, fixed in position including finishing and lettering but excluding painting as per drawing and technical specification clause 1704, printing new letter and figures of any shade with synthetic enamel paint black or any other approved colour to give an even shade as per drawings and technical specification clause 1701, planting of trees by the road side avenue trees in 0.60 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge manure, planting the saplings, backfilling the trench, watering, fixing the tree guard and maintaining the plants for one year, providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per irc:35 .the finished surface to be level, uniform and free from streaks and holes., pedestrian crossing2 m in length and providing at 50 cm apart, at edge for old cc portion, providing and fixing of typical mmgsy informatory sign board with logo as per mord specifications and drawing. three ms plates of 1.6 mm thick, top and middle plate duly welded with ms flat iron 25mm x 5m size on back on edges. the lower plate will be welded with ms angle iron frame of 25mm x 25mm x 5mm. the angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 swg sheet tubes posts duly embedded in cement concrete m-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. the top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 swg steel plate tube. all m.s. will be stove enameled on both sides. lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. all sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing clause 1701 and annexure 1700.1, painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and technical specification clause 1701, plastering with cement mortar 1:4 on brick work in sub-structure as per technical specifications, brick masonry work in cement mortar 1:3 in parapet excluding pointing and plastering as per drawing and technical specifications clauses 600, 900 and 1208.4, 300mm irrigation pipe, providing and laying of a reinforced cement concrete pipe duct, 300 mm dia, across the road new construction, extending from drain to drain in cuts and toe of slope to toe of slope in fills, constructing head walls at both ends, providing a minimum fill of granular material over top and sides of rcc pipe as per irc:981997, bedded on a 0.3 m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe, subject to minimum 450 mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per irc: 98 - 1997 and approved drawings., , 12 % gst, 1% labour cess, seigniorage fee, 5 year maintenance cost, 12 % gst, 1% labour cess, seigniorage fee, hilsa ranri bans bigha pendapur mmgsy road to balapar the house of akhilesh ray, clearing and grubbing road land by manual means including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300mm, removals of stumps of such trees cut earlier & disposal of unserviceable materials & stacking of serviceable materials to be used or auctioned upto a lead of 1000 m including removal and disposal of top organic soil not exeeding 150mm in thickness as per technical specification clause 201.1 and direction of e/i, construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table 300.2 with lead upto 1000 m as per technical specification clause 303.1., construction of un-reinforcedplain cement thickness as perdesign, over a prepared sub base with 43 grade cement or any other type as per clause 1501.2.2 m 30 grade coarse and fine aggregate maximum size of aggregate not exceding 25mm, mixed in a concrete of not less than 0.2cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork steel channel, laying and fixing of 125 micron thick plythene film, wedges, steel plates including levelling the formwork as per drawing spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, constrution joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/ culvert and construction joints, admixtures as approved, curing of concrete slab for 14 days curing compound where specified and water finishing to lines and grade as per drawing and technical specification clause 1501., ii km stone, iii 200 m stone, retro-reflectorised traffic signsproviding and erecting direction and place identification retro-\reflectorised sign as per irc:67 made of encapsulated lens type reflective sheeting vide clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on mild steel angle iron posts 75 mm x 75 mm x 6 mm, 2 nos. firmly fixed to the ground by means of properly designed foundation with m-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and technical specification clause 1701., 600 mm equilateral & triangle, 600 mm circular, 600 mm x 450 mm rectangular, 900 mm side octagon, reinforced cement concrete m15 grade boundary pillars/local stone of standard design as per irc:25, fixed in position including finishing and lettering but excluding painting as per drawing and technical specification clause 1704, printing new letter and figures of any shade with synthetic enamel paint black or any other approved colour to give an even shade as per drawings and technical specification clause 1701, at edge for old cc portion, providing and fixing of typical mmgsy informatory sign board with logo as per mord specifications and drawing. three ms plates of 1.6 mm thick, top and middle plate duly welded with ms flat iron 25mm x 5m size on back on edges. the lower plate will be welded with ms angle iron frame of 25mm x 25mm x 5mm. the angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 swg sheet tubes posts duly embedded in cement concrete m-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. the top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 swg steel plate tube. all m.s. will be stove enameled on both sides. lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. all sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing clause 1701 and annexure 1700.1, cross drainage works/protection/repair, earth work in excavation for foundation of structures upto 3.0 m depth as per drawing and technical specification clause 1104, providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications clause 802, 803, 1202 & 1203 pcc m-15 grade, providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications clause 802, 803, 1202 & 1203 pcc m-20 grade, painting on parapet wall black & white strips painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and technical specification clause 1701, providing and laying rcc pipe np-3 for culverts on first class bedding of pcc m10 material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling concrete and masonary works in head walls and parapets as per clause 1106, plastering with cement mortar 1:4 on brick work in sub-structure as per technical specifications, brick masonry work in cement mortar 1:3 in parapet excluding pointing and plastering as per drawing and technical specifications clauses 600, 900 and 1208.4, 300mm irrigation pipe, providing and laying of a reinforced cement concrete pipe duct, 300 mm dia, across the road new construction, extending from drain to drain in cuts and toe of slope to toe of slope in fills, constructing head walls at both ends, providing a minimum fill of granular material over top and sides of rcc pipe as per irc:981997, bedded on a 0.3 m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe, subject to minimum 450 mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per irc: 98 - 1997 and approved drawings., , 12 % gst, 1% labour cess, seigniorage fee, 5 year maintenance cost, 12 % gst, 1% labour cess

Central Government/Public Sector

TRN :24673362 | 28 Jun, 2022

Tender Value : 1.33 Lacs

Hyderabad - Telangana

Tender for maintenance operation electrical installation & fans in 2nd mso bldg and cg hostel bldg kol20 dg 2022-23sh: pdg iei accessories and wiring in quality control office

Central Government/Public Sector

TRN :24673699 | 28 Jun, 2022

Tender Value : 0

Salem - Tamil Nadu

Tender for supply of high silica locomotive sand 90% minimum free from clay, salt, loams, mica and other foreign materials conforming to aar specifications m-916-51revised 1994 duly cleaned, sieved, dried and packed & stitched in 10 kgs capacity in good quality polythene bags or bio degradable bags conforming to bis 9685/1981 firms offer make/brand self. 4500 bags are to be delivered to chief crew controller/erode and 3000 bags are to be delivered to chief crew controller/salem

State Government

TRN :24656152 | 01 Jul, 2022

Tender Value : 0

Shillong - Meghalaya

Tender for expression of interest of setup of honey processing plants, beebox manufacuturing unit and honey quality control laboratory

Corporations And Associations And Others

TRN :24659428 | 13 Jul, 2022

Tender Value : 1.48 Crore

Karbianglong - Assam

Tender for construction of soil testing quality control and input testing stqc and it laboratory at diphu

State Government

TRN :24660353 | 08 Jul, 2022

Tender Value : 12.36 Lacs

Ajmer - Rajasthan

Tender for supply and installation of quality control equipments at regional labroratory

Central Government/Public Sector

TRN :24660430 | 04 Jul, 2022

Tender Value : 0

Tiruchirappalli - Tamil Nadu

Tender for supply of washer, round, flat for 3/8 bolt size, id:11mm, od:20mm, thickness:2mm, material: en2 cr zinc plated or phosporated. high tensile, hexagonal head bolt 3/4 -10 tpi bsw x 2-1/4 long fully threaded 1-1/8 across flat 15/32 head thickness with 1/8 fillet radius of shank and head, thread should be rolled andconfirm to course medium class of bs:84-1956 bolt confirming to property grade 8.8 of is: 1367/part -3/2002/bs:1768, grade s /sae grade-5 with a rectangular section spring washer of dia 3/4 as per spec: is 1802/1951 and hexagonal nut of dia 3/4 conforming to property grade 1 as per is 1768/1963.note: 1 test procedure for quality control of the fastener shall be done as per the dlw specn.no.misc-109

corporations/Associations/Others

TRN :24664165 | 06 Jul, 2022

Tender Value : 9.01 Lacs

Bangalore - Karnataka

Tender for repairs and improvements to central quality control sub division office dam site

Related Searched Keywords : quality control

List of latest Quality-Control Tenders in Indian Tenders. Click on any Quality-Control Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for Quality-Control Tenders.

Tender for maintenance operation electrical installation & fans in 2nd mso bldg and cg hostel bldg kol20 dg 2022-23sh: pdg iei accessories and wiring in quality control office

Tender for expression of interest of setup of honey processing plants, beebox manufacuturing unit and honey quality control laboratory

Tender for construction of soil testing quality control and input testing stqc and it laboratory at diphu

Tender for supply and installation of quality control equipments at regional labroratory

Tender for repairs and improvements to central quality control sub division office dam site

Get quality control Tender Alert...

Related Searched Keywords : quality control

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us