Filters

List of plaster-of-paris Tenders

List of latest plaster-of-paris Tenders in Indian Tenders. Click on any plaster-of-paris Tenders to view BOQ, NIT and Tender Documents. Get GeM Registration and Bidding Support, Vendor Registration for plaster-of-paris Tenders.

All-Tenders (35)
|
Today's-Tenders
|
Active-Tenders
|
Closed-Tenders

State Government

TRN :49022392 | 13 May, 2025

Tender Value : 31.44 Lacs

Gangapur - Maharashtra

Tender for providing electrical installation in, premises street light, water pump and fire extinguisher for the newly constructed zilla parishad primary health center (p .h .c)main building (g.f+f.f) [under scheme d.p.c. (general) year 2022-23, 34512595 construction expantion & m/ce & repairs of p.h.c/ phsc) at village,lasur stationtq. gangapurdist. chhatrapati sambhajinagar.= 1 supplying and erecting 25 mm dia. corrugated flexiblepolypropyleneconduit 2 supplying anderectingpvctrunking (pvccasing-n-capping)ofsize25 mm with accessorieson wall/ceiling as per specification no: wg-ma/con. 3 supplying anderectingpvctrunking (pvc casing-n-capping)ofsize20 mm with accessorieson wall/ceiling as per specification no: wg-ma/con. 4 supplying anderectingpvctrunking (pvccasing-n-capping)ofsize32 mm with accessorieson wall/ceiling as per specification no: wg-ma/con. 5 supplying anderectingpvctrunking (pvccasing-n-capping)ofsize40 mm with accessorieson wall/ceiling as per specification no: wg-ma/con. 6 supplying and erecting mains with 2x1.5 sq.mm frlshcopperpvc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places as per specification no: wg-ma/bw 7 supplying and erecting green earth wire 1x1.5 sq.mm frlshcopperpvc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places as per specification no: wg-ma/bw 8 supplying and erecting mains with 2x2.5 sq.mmfrlsh copper pvc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places. as per specification no: wg-ma/bw 9 supplying and erecting green earth wire 1x2.5 sq.mmfrlsh copper pvc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places. as per specification no: wg-ma/bw 10 supplying and erecting mains with 4x2.5 sq.mmfrlsh copper pvc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places. as per specification no: wg-ma/bw 11 supplying and erecting mains with 2x4 sq.mm frlsh copper pvc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places. as per specification no: wg-ma/bw 12 supplying and erecting mains with 4x4 sq.mm frlsh copper pvc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places. as per specification no: wg-ma/bw 13 supplying and erecting green earth wire 1x4 sq.mm frlsh copper pvc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places. as per specification no: wg-ma/bw 14 supplying and erecting mains with 4x6 sq.mm frlsh copper pvc insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places. as per specification no: wg-ma/bw 15 supplying and erecting pvc insulated pvc round sheathed 1.5 sq.mm (30 no. x 0.25 mm dia.) 3 core flexible multi strandedcopper industrial cable for voltage grade up to 1.1 kv 16 supplying and erecting pvc insulated pvc round sheathed 2.5 sq.mm (50 no. x 0.25 mm dia.) 3 core flexible multi strandedcopper industrial cable for voltage grade up to 1.1 kv 17 supplying and erectingceiling rose / batten holder / slanting holder / hanging cord switch / hanging bell push / pendant holder bakelite base 6a. erected on filled polypropylene board or polished double wooden block/ pvc junction box. 18 supplying and erectingmodular type switch 6a / 10a duly erected on provided plate and box with wiring connections complete. 19 supplying and erectingmodular type switch 16aduly erected on provided plate and box with wiring connections complete. 20 supplying and erectingmodular type bell-push with indicator 2 modules 6a / 10a, duly erected on provided plate and box with wiring connections complete. 21 supplying and erectingmodular type 3 pin 6amultisocket with safety shutter, duly erected on provided plate and box with wiring connections complete. 22 supplying and erectingmodular type 3 pin 6 / 16amultisocket with safety shutter,duly erected on provided plate and box with wiring connections complete. 23 supplying and erectingmodular type (two module) electronic step regulator for fan, duly erected on provided plate and box with wiring connections complete. 24 supplying and erecting modular type blanking plate one module, duly erected on provided plate & box. 25 supplying and erecting pvc surface modular switch box with double mounting plate for 2module duly erected. 26 supplying and erecting pvc surface modular switch box with double mounting plate for 3module duly erected. 27 supplying and erecting pvc surface modular switch box with double mounting plate for 6module duly erected. 28 supplying and erecting pvc surface modular switch box with double mounting plate for 12module duly erected. 29 supplying and erecting 16 / 20 / 25 a starter (modular range) 2 module for ac unit on provided box complete & duly concealed with necessary material and connected. 30 point wiring for light/bell/exhaust fan in pvc trunking (casing-capping) with 1.5 sq.mm (2+1e) frlsh grade copper wire, modular type switch, earthingand required accessories as per specification no: wg-pw/sw 31 point wiring for ceiling fan in pvc trunking (casing-capping) with 1.5 sq.mm (2+1e) frlsh grade copper wire, modular type switch, earthingand required accessories as per specification no: wg-pw/sw 32 wiring for plug on board withswitch socket surface/concealed type, copper wiring and earthing and with modular accessories as per specification no: wg-pw/cw 33 supplying and erectingled square / circular max. 11 w down lighter/panel light having pressure die-cast aluminium housing,polystyrene diffuser havingsystem lumens output of min. 1200 lumens, min. efficacy of 110 lumen/w, cri>80, cct upto 6500k, beam angle of 120 deg., max. ripple of 5%,thd<10%, p.f. >0.95, operating range of120-270v, surge protection of 2.5 kv, life class of 50,000 hrs. at l70b50,including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty. 34 supplying and erectingled square / circular max. 14 w down lighter/panel light having pressure die-cast aluminium housing,polystyrene diffuser havingsystem lumens output of min. 1500 lumens, min. efficacy of 110 lumen/w, cri>80, cct upto 6500k, beam angle of 120 deg., max. ripple of 5%,thd<10%, p.f. >0.95, operating range of120-270v, surge protection of 2.5 kv, life class of 50,000 hrs. at l70b50,including driver,having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty. 35 supplying and erectingled square / circular max. 18 w down lighter/ panel light having pressure die-cast aluminium housing,polystyrene diffuser having system lumens output of min. 2000 lumens, min. efficacy of 110 lumen/w, cri>80, cct upto 6500k, beam angle of 120 deg., max. ripple of 5%,thd<10%, p.f. >0.95, operating range of120-270v, surge protection of 2.5 kv, life class of 50,000 hrs. at l70b50, including driver,having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty. 36 supplying and erectingledpanel light(600mm x 600mm) max. 30 whaving crca powder coated housing,polystyrene diffuser havingsystem lumens output of min. 3600 lumens, min. efficacy of 120 lumen/w, cri>80, cct upto 6500k, beam angle of 120 deg., max. ripple of 5%,thd<10%, p.f. >0.95, operating range of120-270v, surge protection of 2.5 kv, life class of 50,000 hrs. at l70b50including driver,having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty. 37 supplying and erecting anodized aluminium corridor / passage / mirror light led fitting (2 feet) max. 12wwith high transitivity diffuser with min. system lumens output of 1200 lumens, min. efficacy of 100 lumen/w, cri>80, cct upto 6000k, beam angle of 110 deg., ripple<5%,thd<10%,p.f. >0.95, operating range of200-270v, surge protection of 2 kv, life class of 50,000 hrs. at l70b50, including driver with end caps on provided pvc block / wooden board with 3 years warranty. 38 supplying & erecting inverter led batten 10w tube light fitting with polycarbonate housing, heat sink, integrated hf electronic driver, min. 2600 mah lithium ion battery with charging time of 8-10 hours and backup time of min. 3 hrs. with minimum 25% of initial watts having luminous efficacy of 100 lumen/watt,cri>80, cct of 6500k and thd<=20% havinguseful life of minimum 25000 hrs. with overheating protection with 2 years warranty. 39 supplying & erecting inverter led batten 20w tube light fitting with polycarbonate housing, heat sink, integrated hf electronic driver, min. 2600 mah lithium ion battery with charging time of 8-10 hours and backup time of min. 3 hrs. with minimum 25% of initial watts having luminous efficacy of 100 lumen/watt,cri>80, cct of 6500k and thd<=20% havinguseful life of minimum 25000 hrs. with overheating protection with 2 years warranty. 40 supplying and erecting ding dong / electronic musical type call bell with heavy duty coilsuitable to operate on 230v a.c. supply erected on polished double wooden block/sunmica block of suitable size. 41 supplying and erecting integrated led street light fitting26 to 30w ip65 & ik08 class having single piece pressure die-cast aluminium housing ,having system lumens output of min. 2600 lumens, min. efficacy of 100 lumen/w, cri>70, cct upto 6500k, thd<10%, p.f. >0.95, operating range of140-270v, inbuilt surge protection of 10 kv, life class of 50,000 hrs. at l70b50,including driver complete with 3 years warranty as per specification nofg-odf/fls2. 42 supplying and erecting integrated led street light fitting 40 to 50w ip65 & ik08 class having single piece pressure die-cast aluminium housing,havingsystem lumens output of min. 4400 lumens, min. efficacy of 110 lumen/w, cri>70, cct upto 6500k,thd<10%, p.f. >0.95, operating range of140-270v, inbuilt surge protection of 10 kv, life class of 50,000 hrs. at l70b50, including driver complete with 3 years warranty as per specification nofg-odf/fls2. 43 supplying and erecting integratedled street light fitting 100-110w ip65 & ik08 class having single piece pressure die-cast aluminium housing,havingsystem lumens output of min. 11000 lumens, min. efficacy of 110 lumen/w, cri>70, cct upto 6500k, thd<10%, p.f. >0.95, operating range of140-270v, inbuilt surge protection of 10 kv, life class of 50,000 hrs. at l70b50,including driver complete with 3 years warranty as per specification nofg-odf/fls2. 44 supplying & erecting integral post top lantern fixtures (mushroom type) suitable for led lamp upto 12 w consisting of clear acrylic top cover, cast aluminium pole cap complete with accessories on provided pole /bracket as per specification no. fg-odf/ptl 45 supplying and erecting street light wall bracket made from 40 mm. dia ‘ g.i. pipe 1.2 m. in total length complete as per specification no. fg-bkt/wb 46 supplying & erecting 3w, 230v integral type led lamp suitable for b-22 / e-27 base.(night lamp) 47 supplying and erecting regular/ standard model ceiling fan of 900 /1050 mm. sweep complete erected in position as per specification no. fg-fn/cf 48 supplying and erecting bracket fan 400 mm. sweep a. c. 230 volts 50 cycles 1350 rpm. oscillating type, plastic or metal blades chrome plated guard with speed regulator and moisture proof treatment to winding and with ‘e’ class insulation. 49 supplying and erecting fresh air cum exhaust fan of light duty 250 v a.c. 50 cycles 300mm. 1400 rpm rust proof body & blades, wire mesh, duly erected, complete. 50 supplying and erecting exhaust fan heavy duty 230 v a.c. 50 cycles 375/380 mm. 1400 rpm complete erected in position as per specification no. fg-fn/exf 51 supplying and erectingenergy saving ceiling fan 230 v a.c. 50 cycles 1200 mm complete erected in position as per specification no. fg-fn/cf 52 supplying and erecting fan hook of 10 mm. m.s. round bar grouted in rcc slab with making the site as original. 53 providing recess in brick wall suitable for erection of exhaust fan up to 450mm. sweep complete with grouting of nut, bolts, plastering and colour washing to match the colour of the wall for the wall thickness of 225 mm. 54 supplying & erecting 22 swg g.i sheet metal cawl sector shaped with 25 x 25 x 3 (mm) angle iron frame, metal mesh to avoid birds entry with necessary material, suitable for exhaust fan of 400 mm as per specification no fg-fas/msc 55 supplying and erecting midget type 3.0 litres instant type water heater of rustproof & shockproof abs plastic body, high grade ss inner tank & 3kw heating element with corrosion & hard water protection, with minimum 3 safety protections (i.e. thermostat & thermalcut-out, function valve) complete with 6.5 bar pressure withstanding capacity 230/250v, 50hz, a.c. supply with inlet and outlet, with 3 core pvc flexible copper wire leads duly tested and marking sr. no. and date of erection complete. 56 supplying and erecting chromium plated heavy duty brass stop cock for inlet pipe of water heater (15mm. dia). 57 supplying & erecting 15mm brass non return valve for inlet pipe of storage water heater. 58 providing fiber reinforced pvc flexible pipe upto 1m length with brass locking nuts and washers and clips at both ends suitable for hot water and cold water both (1 set of 2 nos.) complete. 59 supplying, installing, testing & commissioning split type variable speed invertertechnology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 1.3tr to 1.6tr capacity having iseer minimum 3.8 to maximum 4.39 suitable to operate on 250v, 50 hz, a.c. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant r32 having copper condenser, minimum 2.5pm filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dba at position as per specification no. apac/ wac 60 supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 1.7tr to 2.0tr capacity having iseer minimum 3.8 to maximum 4.39 suitable to operate on 250v, 50 hz, a.c. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant r32 having copper condenser, minimum 2.5pm filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dba at position as per specification no. apac/ wac 61 supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with rohs compliant suitable for refrigerant having 22swg thickness and inner dia/size 12mm complete. 62 supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with rohs compliant suitable for refrigeranthaving 22swg thickness and inner dia/size 16mm complete. 63 supplying, erecting, testing and commissioning self contained water cooler 230/250v 50hz nominal cooling capacity of 80 litres per hour and storage capacity 120 litres with partially stainless steel body as per specification no. ap-wcr/wc 64 supplying, erecting, testing and commissioning self contained water cooler 230/250v 50hz nominal cooling capacity of 150 litres per hour and storage capacity 150 litres with partially stainless steel body as per specification no. ap-wcr/wc 65 supplying and erecting ultra violet storage type water purifier (ro+uv+uf) with softener for safe drinking water consisting of uv germicidal tube of 8w capacity choke made of copper wire and two indicator lamps with output of purified water minimum 0.33 litre/min with activated carbon filter and softener operating on 230v, single phase a.c. supply with uv fail & filter change indication system .(for tds more than 200) 66 supplying, installing, testing and commissioning of single phase, 230v, 50 hz, 1400 to 1600va digital pure sine waveinverter with backup time of ........ hrs. based on insulated gate bipolar transistor (igbt) technology completeas per specification no.ap-inv 67 supplying and erecting 12v/180ah tubular battery with battery terminal wire, duly charged with 36 months warranty complete 68 supplying and erecting fully automatic line voltage stabilizer buck and boost type for operation on input voltage 160-270v and output voltage 200-250v rated for 3kva maximum load and with voltmeter, selector switch, 6a/16a flush type 3 pin socket for output and with 3 core copper flexible cord and 3 pin 6/16a plug top with overload & short circuit protection complete. 69 supplying and erecting switch disconnector fuse (sdf) switch 415v, 100a,open execution, four poleac23 a rated with terminal shrouds on both sides and phase barriers along with telescopic shaft for depth adjustments and door interlock and padlock complying to is/iec 60947-3 part-1/3hrc - din type fuse, insulation voltage 1000 vfor enclosing in panel with rotary handle for on / off operation (without hrc fuse) 70 supplying & erecting three phase, 415v, street light control panel up to the max load of 6kw, tpn mcb 40a,powder coated crca 14 swg sheet, outdoor type, having ip54,ik10 protection, suitable rating contactor, 24 hrs. astronomical time switch with minimum 5 years battery back up,auto/manual selector switch, on/off push buttons, indicator lamps, control wiring, metering device, etc. for automatic operation, with overcurrent, short circuit, earth fault protectionon provided iron frame / cc foundation. 71 supplying, erecting & marking spmcb 0.5a to 5a, c-series with rated short - circuit breaking capacity (icn) 10kain provided distribution board as per specification no. sw-swr/mcb 72 supplying, erecting & marking spmcb 6a to 32a, c-serieswith rated short - circuit breaking capacity (icn) 10ka in provided distribution board as per specification no. sw-swr/mcb 73 supplying, erecting & marking spmcb 6a to 32a, b-series with rated short - circuit breaking capacity (icn) 10ka in provided distribution board as per specification no. sw-swr/mcb 74 supplying, erecting & marking dpmcb 6 a to 32 a, b-series with rated short - circuit breaking capacity (icn) 10ka in provided distribution board as per specification no. sw-swr/mcb 75 supplying, erecting & marking tpmcb 6a to 32a, with rated short - circuit breaking capacity (icn) 10ka in provided distribution board as per specification no. sw-swr/mcb 76 supplying, erecting & marking tpmcb 40a to 63a, with rated short - circuit breaking capacity (icn) 10ka in provided distribution board as per specification no. sw-swr/mcb 77 supplying, erectingand marking double pole isolator only switch version of miniature circuit breakerof40awith required wiring connections and lugs etc. in provided distribution board. 78 supplying, erecting and markingfour pole isolators only switch version of miniature circuit breakers of 40a in provided distribution board. 79 supplying, erecting and markingfour pole isolators only switch version of miniature circuit breakers of 63ain provided distribution board. 80 supplying&erectingtriplepole and neutral distribution board (tpndb), sp/tp mcbs total 4 ways /12 poles, with door, 1.2mm thickness surface/flushmounted, ip 43 protection on iron/gi frame (vertical busbar type) as per specification no. sw-swr/mcbdb 81 supplyingand erecting single pole and neutral distributionboard (spndb), with 2 ways for incoming and 6 ways (6 poles) for outgoing sp mcbs, with door, 1.2mm thickness surface / flush mounted, ip 43 protection on iron / gi frame as per specification no. sw-swr/mcbdb 82 supplying & erecting crca sheet metal one way enclosures of 1.2mm thickness suitable for dp mcb /tp mcb/fp mcb/rccb/rcbo complete erected on angle iron/gi frame. 83 supplying & erecting triple pole and neutral distribution board (tpndb), 3 pole/4 pole mccb as incomer & outgoing sp mcb (36 poles) or tp mcb of 12 ways (36 poles), with door, 1.2mm thickness, surface/flush mounted, on iron/gi frame (vertical busbar type) as per specification no. sw-swr/mcbdb1 84 providing & erecting 4 pole mccb, 415 v, 100a, rated short-circuit breaking capacity 25 ka (ics=100% of icu), adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/uv/trip alarm contact.mccb with phase barriers on both sides, insulation withstand capacity 800v, no line-load bias in provided enclosure/panel as per specification no. sw-swr/mccb (rate of 3 pole mccb +20% for 4 pole mccb= 5309x20%+5309=6370.80) 85 supplying and erecting cupboard for enclosing switchgears orforany other purposemadefromselected marine plywood planks 19 mm thick duly varnished/ painted from inside and from outside with brass hinges and locking arrangement with suitable lock with keys in duplicate. cupboard shall be duly grouted with suitable size of iron work in wall at the bottom. (size of cupboard 0.5x1x2+0.5x1x2+1x1x2= 4 sq.mtrs.) 86 supplyinganderectingiron, sheet metal work consisting of crcasheets, varioussectionsofiron,plates, chequeredplates,rods,bars,mspipes,etc. forpanel board or any other purpose with bending, cutting, drilling and welding completeerectedatthepositionwith necessarymaterialsdulypaintedwith one coat of red oxide and two coats of enamelpaint to match the switchgears or as per directions by the authority. ( 50x50x4mm angle @ 3.4 kgs x 6 mtrs.= 20.40 kgs i,e 20 kgs. 87 supplying and erecting 525 v 3 phase, 50 hz., mpp type capacitor having minimum overcurrent capacity of 1.8 in,peak inrush current capacity 300 inand minimum life 150000 hourskvarbank of all polypropylenecondensers (app)withthestandard capacities of 2, 3, 5, 7, 10, 12.5 and 15 kvarunitsofp.f. correctionforoperationon 3 phase 50 hz. with externally discharging resistances, earthing terminals and built on angle iron or channel iron frame work and providedwithterminalcoverbox completeerected onprovidediron bracketoronfloordulytestedby licensee.( original p.f=0.8 desired p.f = 0.95 for this multiplying factor is 0.421. so 0.421 x 46.440 = 19.55 i.e 10 kvar x 2= 20 kvar) 88 supplying, erecting & terminating fr xlpe insulated, galvanised steel formed wire armoured (strip) cable 1100 v, 2 core 6sq. mm. aluminium conductor completeerected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipeas per specification no. cb-lt/al 89 supplying, erecting & terminatingfr xlpe insulated, galvanised steel formed wire armoured (strip) cable 1100 v, 3½ core50 sq. mm. aluminium conductor completeerected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipeas per specification no. cb-lt/al (double run) 90 supplying, erecting & terminatingfr xlpe insulated, galvanised steel formed wire armoured (strip) cable 1100 v, 4 core6sq. mm. aluminium conductor completeerected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipeas per specification no. cb-lt/al 91 supplying & erecting g.i. pipe‘a’ class 50 mmdia.erectedfor enclosingxlpearmouredcable on wall/poleas per specification no. cb-ce 92 supplying andlaying (including excavation of suitable width & depth up to 90 cm) 50 mmoutside dia. double wall corrugatedpipes(dwc) ofhdpe for enclosing cable below ground/road surface, to required depth complete. 93 supplying and laying (including excavation of suitable width & depth up to 90 cm) 75 mmoutside dia. double wall corrugatedpipes (dwc) ofhdpe for enclosing cable below ground/road surface, to required depth complete. 94 supplying & erectingcast iron cable indicatorplate buried along with route of cable for pvc / xlpe armoured cableas per specification no. cb-cip 95 supplying & erecting frp box of size 150mm x 125mm x 100 mm, 2.7 mm thickcomplete on pole/wallas per specification no. cb-sb 96 providing & erecting 8 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 135 mm a/f, top 70 mm a/f on provided foundation as per specification no. oh-pl/opl 97 providing and erecting galvanised 1000mm single arm sword type bracket with frp dome and ball as per specification no. oh-pl/pbkt 98 providing and erecting galvanised 1000mm double arm sword type bracket with frp dome and ball as per specification no. oh-pl/pbkt 99 providng earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results asper specification no. ea-ep 100 providing earthing with copper earth plate size 30 x 30 x 0.315 cm complete with all materials, testing & recording the results asper specification no. ea-ep 101 providingpipetype earthing with 40mm. dia. g.i. pipe or 20 mm dia. g.i. rodcomplete with all materials testing and recording the results as per specification no. ea-ep 102 supplying and erecting gi strip of required size used for earthing on wall and/or any other purpose with necessary gi clampsfixed on wall painted with insulating and non-corrosive bond with requiredjointsas per specification no. ea-ep.(25x3mm strip. perpole 1.5 mtrs. so for 13 poles 13nos.x1.5mtrs.= 19.5 mtrs. weight of strip @0.590kgs/mtr. so 19.50mtrs.x0.590kgs.=11.51 kgs.) 103 supplying and erecting minimum three & above star rated 1 phase, 230 v, 50 hz, submersible pump set of 1.5 kw/2hp suitable for erection on open well, pump having delivery head from 29to 7 m and discharge from 30 to 600 litres. . per minute& pipe of suction 50 mm/delivery 50 mm diameter erected with necessary h type clamps as per specification no. wp-osp 104 supplying & erecting flat flexible 3 core 4 sq.mm pvc sheathed submersible type copper cable suitably clamped at fixed intervals with column pipe assembly complete. 105 supplying & erecting automatic control panel for 1 ph, 230 volt, a.c. submersible/centrifugal pump set up to 3 hp consisting of dol starter of suitable relay range s.p.p., combined ammeter/ voltmeter, phase indicating lamp enclosed in crca powder coated vibration proof enclosure with ip 54 protection. 106 supplying & erecting carbon dioxide (co2) fire extinguisher of 4.5 kg. capacity cartridge type conform to is 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. m. s. flat with nut & bolts routed in wall complete. 107 making cement concretefoundationin 1:3:6 cement concrete,(20 to 25) mm. stone metal duly plastered with necessary curing forcomplete. (02x02x02 foundation for main control panel stand and for street light control panel 0.2x0.2x0.2mtr.=0.16 cu.mtrs.) 108 makingm- 20 grade reinforced cement concretefoundation by considering the safe soil bearing capacity at site as 10 t/sq.mat 1.5 m depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 6m to 8m high octagonal /conical gi pole). 109 supplying and erecting isi mark gi pipe 50 mm dia.‘b’ class at position with accessories complete as per specification no. cw-plb/gp. 110 supplying and erecting high density polythene pipe isi mark 50 mm. dia. suitable for pressure of 6 kg. / cm2 connected tojet/submersible pump with required material complete. 111 supplying and erecting 50 mm dia. gun metal sluice valve at position with necessary materials complete. 112 supplying and erecting non return valve 50 mm dia in position made of gun metal complete. 113 lum sump provision towards service connection charges1 no.3 phase @ rs. 55000/-/per total rs.55,000/-

Co-operative

TRN :49022717 | 20 May, 2025

Tender Value : 0

Powayan - Uttar Pradesh

Tender for supply of hardware and general material and nut bolt items supply of hardware and general material and nut bolt items for season 2025-26 , description , norton make sander disk alkon gold plus. grit no. 80 size 100mm. , -do- 36 no. size 100mm , holdite in perfect liquid in ½ kg. tin. , white lead sakura make. , lead wire size 1mm in 500 gm roll. , emery cloths rough carbandom make. , carbandom make emery cloth medium. , -do- fine. , emery tape rough in 50 mtr. long size 2” carbondam make. , -do- fine , carbandom make emery paste in 400 gm rough. , -do- medium , -do – fine , annabond 112 (50 gms.) , annabond 666 (100gms). , araldite in 180 gms. , araldite in 1.8 kgs. , blue tube in 20ml. , loctite no. 270 in 50ml. , -do- no. 262 in 50ml. , rustoline in ½ ltr. tin. , teflon tape size ½” , -do- ¾” , -do- 1” , m.seal phata phat in 25gms. , graphite powder in ½ kg. tin. , braso in 100ml. , rubber hose pipe size 1” suitable for 10 kg./cm2 pressure and temperature 100 degree. , unique make complete rubber tyre coupling size px/tc/ph. , unique make spare tyresize px/tc/phdiscount. , rope pulley one groove , rope pulley two groove. , rope pulley three groove. , d-cycle cap. 2 ton. , -do- 5 ton. , -do- 10 ton. , cotton waste coloured. , garware make p.p. rope size 18mm (3/4”) with tc. , jyoti make pure rubber sheet size 1/8 , -do- size ¼ and above. , bearing sleeve jmc make different size , polyster wire sealing size 1 ton x 2 mtr. long. , -do- size 2 ton x 3 mtr. long. , -do- size 5 ton x 2 mtr. long. , indef make chain pulley block one ton capacity with 10 mtr. lift p-model with tc. , -do- 3 ton capacity with 10 mtr. lift. , rubber oil seal mykoda make different size , c.i.plumber block s.m.r make different size , tefflon rod size 50mm x 300mm. , brass shim 0.05x14”x48”. , brass shim size 0.1x14”x48” , -do- smoke grey. , -do- light grey. , -do- sky blue. , namda different size. , diamond make wire braided rubber hose pipe both side bsp fitting size ¼” x 800mm , -do- size ½” x1500mm. , audco make cock valve (plug valve) flanged end size 3” (80mm) regular pattern standard type wrench operated. , spring steel flat differentsize. , ms round different size. , en-8 rod different size. , ci pulley b-section groove no.3 size 4” dia. , -do- c-section groove no. 4 size 8” dia. , brass liner 40mesh x 2 ft. x 13.125 sft. , rubber hose pipe size ¾” for 100o temperature and working pressure 10kg/cm2 , ms perforated sheet hole size 5mm dia size width 900mm x length 2400mm x 3mm thick. , renold chain different size diamond make. , ms. square different size. , oil paper. , ms chain size 5mm , hydrolic connector size 3/8”x1/4” , -do- size 3/8”x3/8” , -do- size ¼”x1/4” , hose clamp suitable size 1”id pipe. , glass lubricator cap. ½ ltr. no.8 connection size ½” bsp. , brass shim 0.05mmx 14”x48” , -do- 0.10mm x 14”x48” , -do- 0.15mmx14”x48” , -do- 0.20mm x 14”x48” , gm solid rod different size. , brass rod different size , sight glass toughened size 210x15mm , hydrolic connector size ½”x14mm , burffi cut zali size 25mm (1”)x4ft. width x 10 gauge x51 ft. long. , glass wool , chcken wire netting 3ft. x 100 ft. , gi binding wire. , silicon bronze rod 1/8”. , double wire braidedsteam hose pipe size ¾” for pressure 21 kg. cm2 and temperature 205oc. , hindustan composite ltd. make brake liner size ¼”x3”. , loctite in 20ml no. 406 , m-seal pidite make , c.i. v belt pulley section c groove no. 4 dia size 7” , -do- section b groove no. 3 dia size 6”. , gun metal valve sant make , totem make die nut bsf size 3/8” , -do- size ½” , -do- size 5/8” , -do- size ¾” , power master tube exponder 42mm id x 45mm od. , copper rod size 1 ½” , cast steel steam valve wj make different size , copper tube pvc coating size ¼” , copper tube cutter , ss tube cutter size 16mm , copper pipe size 10mm x 1.5mm , push pull tee size 8x8x8mm , push pull connector male size ¼”xfemale size 8mm. , -do- size ½” x female 8mm. , pvc tube working pressure 12kg/cm2 size 8mm , brass connector with both side nut and female ¼” , brass nut size ¼” , brass ferrule size ¼” , brass connector size ½” male x ¼” female. , brass connector size 3/8”x1/4” , brass elbow with ferrule size ¼” , brass tee size ¼”x1/4”x1/4” , brass reducer size ½ x 1/4” , brass reducer size ½” x 3/8” , brass reducer size 3/8x1/4” , brass ferrule size 10mm , brass connector with nut and ferrule for size 10mm od , aluminium fitting make thread size ¼”x1/4” , -do- size ½”x1/4” , -do- size 3/8”x1/4” , -do- size ¾”x1/4” , aluminium elbow make thread size ¼”x1/4” , ss connector for with nut and ferrule for size 16mm od tube. , heavy duty plumber block for 22334 k bearing (634). , moscot make isi marked double rope safety belt. , indfos make pressure switchrange 0.5mm to 7 kg/cm2, ¼” bsp fittings. , hap/h.guru make pressure gauge 6” dia bottom entry ½” bsp range 0.21 kg./cm2 , -do- range 0.40 kg./cm2 , h.guru make /hap make pressure gauge dia size 2” range 0.10 kg./cm2 back fitting size ¼” , janatics make air filter regulator range 0.10 kg/cm2 with gauge glass zie ¼” , lp make butter fly valve with ss wafer size 1 1/2 “ , clamp for pipe size 1” , u clamp size ¾” , flat belt size 2”x4 ply. , elegator 45 nos. , hydroulic pipe od 20mmx15mm id suitable for 300 kg/cm pressure. , hydroulic ferrule for 20mm od tube. , hydroulic connector with nut size : 20mm , copper tube size 3/8” , brass ferrule size 3/8” , brass connector with nut size 3/8” , ci diaphragram size 80mm , ci diaphragram valve size 50mm , klinger make gauge glass size a-9 , isi marked ci butterfly valve size 40mm , isi marked ci butterfly valve size 100mm , usha martin ltd. make steel wire rope hemp core size 6/19x3/4”(e.d.inclusive agt m.vat) , isi marked nylon rope with t.c. size 20mm , multi screw driver kit.(jhalai make) , mitutoyo make dial indicator with magnetic stand. , lead wire (0.5) mm(500gram per roll) , steam valve high pressure flanged end size ½” , steam valve high pressure flanged size 1” , pu elbow size 8mm , pu connector size 8x8mm , air filter regulator complete with gauge. , cast iron globe value with ss part size 40mm , mud conveyor belt endless 600mm width 3 ply nylon 8mm thick. , sight glass toughened size 200x20mm , sight glass toughened size 100x20mm , ms sprocket 12 teeth x 50mm pitch. , dead nut size ½” , dead nut size 3/8” , brass elbow size 3/8”x3/8” , brass elbow size 3/8”x1/4” , pu tee size 8mm , gauge glass size ¾”x16” , cast iron reflex valve (horizontal +/vertical use) with gun metal working part flanged size 4”. , light resin bounded pads 1.64x1.22x50mm thick.(per sheet of 02 mtr) , becon make teco generator as per serial no. given by you. , becon make teco indicator as per your sr. no. , stainless steel nozzle for de superheating turbine type. , cast steel gauge glass assembly for reflex gauge klinger , pvc tail end flanged heavy duty size 8” , rubber insertion sheet size 5mm , pvc heavy duty end cap size 4” , power grip make heavy duty tin cutter size 12” , chisel , leader make ci butterfly valve with aisi 304 quality wafer size 4”. , leader make ci butterfly valve with aisi 304 quality wafer size 6”. , isi marked ci nrv with gm working part size 6” , teflon rod size 60mmx300mm , imported ph meter. , imported tds meter. , brass connector with 2 nut+2 ferrule 10mm , brass connector with 2 nut + 2 ferrule size 3/8”x3/8” , brass 3/8 male x ¼” female. , brass 1/4” male x 3/8 female. , brass connector complete size ¼”x1/4” , ci pulley close grain 7” -5 groove – b –section. , ci pulley close grain 10”-5 groove – b- section. , ci pulley close grain 13”-5 groove – c- section. , ci pulley close grain 16”-5 groove-c section. , brass connector with 2 nut + 2 ferrule complete. , copper coil size 3/8” od. , plaster of paris. , high pressure hose flexible with female end fitting size 3/8”x1 ½” , -do size ¼”x1 mtr. , dewrance plug sleeve set of 3 pcs size ¾” , rubber conical washer size ¾” , ci nrv with gm working part size 2 ½” , protector for gauge glass size ¾”x16” , v. belt pulley “c” section 4 groove size 7” , teflon rod size 35mmx300mm , -do-12x40 , high pressure hose pipe with both side size ½”x1 mtr. , -do- size ½”x2 mtr. , high pressure hose with bolt side size 3/8x1 mtr. , high pressure hose pipe with both side 3/8x2 mtr. , h.guru/hap make temperature gauge size 6” range 0-350c. , -do- 0-300c. with 3 mtr. capillary stem length 14” , isi marked ci sluice valve flanged end size 1 ½” , leader make gauge glass cock set size ¾” with ibr tc , m.s. nut bolt with washer , m.s. bolt full thread/half thread inch size 1/4 “ to 3/8” , -do- size 1/2 “ to 1 ½ “ , -do- mm size 6 to 10 mm , -do- mm size 12 to 24mm , ms nutsize ¼” to 1 1/2 “ , ms nut mm size 6mm to 24mm , ms washer different size , spring washer bbbb make different size . , h.t. bolt unbrako make different size , split pin champion make different size , ms rivet different size. , alluminium rivit size ¼”x1/2” , nylock nut size 1” , nylock nutsize 24mm , nylock nutsize 27mm , stainless steel allenkeybolt size 8x 25 mm , stainless steel allenkeybolt size 12 x 25 mm , stainless steel allenkeybolt size 12x40 mm , stainless steel allenkeybolt size 12x50 mm , steel screew , s.s. bolt with nut size- 5/8 x 1-1/2apl make , s.s. bolt size- 8 x 25 mm apl make , s.s. bolt size- 8 x40 mm apl make , s.s. bolt size- 8 x50 mm apl make , s.s.nut size- 8 mm apl make , g.i.bolt size- 8 x 80 mm , g.i.bolt size- 6 x75 mm , g.i.bolt size- 10 x100 mm , m.s. fastner bolt size- 12 mm

State Government

TRN :49024279 | 14 May, 2025

Tender Value : 0

Firozabad - Uttar Pradesh

Tender for tender for repair work in government high school niyamatpur firozabad under alankar yojana - dismantling doors and windows leaves including chaukhats but excluding hold fasts and including stacking of materials as directed by engineer-in-charge within a distance of 60 meters (200 feet) ch-17 -si no. 15 (705) 2 dismantling existing plaster including disposal of refuse as directed by engineer-in-charge within a distance of 60 meters. ch-17 -si no. 16 (706) 3 earthwork in excavation in trenches for foundation pipes cable etc. in ordinary soil, including lift upto 1.5 m lead upto 50 m and dressing of sides and ramming of bottom and disposal of surplus excavated earth including all labour, t&p etc. for proper completion of work, as directed by engineer incharge. (si. no. 251) 4 class-150 brick work in 1:3 cement and coarse sand of 1.25 fm mortar in super structure including necessary moulding and cutting of bricks as required including supply of all materials, labour and t&p etc. required for proper completion of the work thickness of wall of half brick thick.ch-6 -si no. 2(6.1) 5 providing and laying in cement concrete 1:1.5:3(1cement:1.5 fine sand:3 graded brick aggregate 20 mm nominal size) and curing complete including cost of formwork in foundation and floors. (si. no. 275) 6 providing and laying in cement concrete 1:4:8 (1cement:4fine sand:8graded brick aggregate 40 mm nominal size) and curing complete including cost of formwork in foundation and floors. (si. no. 275) 7 fixing to steel or wooden chaukhats in position. ch-10 -si no. 9(11.14) (labour only) door chaukhats above 1.5 sq.m. and upto 5 sq.m. 8 fixing to steel or wooden chaukhats in position. ch-10 -si no. 9(11.14) (labour only) window chaukhats above 1.5 sq.m. and upto 5 sq.m. 9 fixing to steel or wooden chaukhats in position. ch-10 -si no. 9(11.14) (labour only) ventilator chaukhats above 1.5 sq.m. and upto 5 sq.m. 10 provinding and fixing glass panes with putty and glazing clips in steel doors, windows,clerestory windows all complete with : 4.0 mm thick panes.ch-9 -si no. new(14) 11 mild steel or iron work in heavy sizes such as built up gates record rack, roof work, gates etc. brought to required form including drilling holes revitting or welding where necessary, and also including supply of steel bolts, nuts, wastage etc. and their fixing require for proper completion of the work. ch-10 -si no. 2, (503) 12 mild steel and iron work of small size and section such as holding down woods, hold fasts tierods, grating, etc. (when not included in and over all rates) brought to required form including supply of steel and its wastage including cost of bolts, nuts if required for proper completion of work including fabrication of holes in door chaukhats and nosing. ch-10 -si no. 3, (502) 13 providing and laying vitrified floor tiles in different sizes (thickness to bespecified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.with out base concrete ch-14 -si no. 24 (11.41) same as above but for 600x600mm size. 14 repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 metres lead : ch-13 -si no. 18(14.1) (b) with cement mortar 1:4 (1cement: 4 coarse sand) 15 12 mm cement plaster 1:4 (1 cement and 4 finesand) in single coat on fair side of single or half brick wall for interior plastering upto floor two level including internal rounded angels chamfers, and/or rounded angles not exceeding 80 mm. in girth and finished even and smooth. no extra for mixing any additive. (ch. 13 item no. 13.4 newly surface. 16 finishing walls with one coat of waterproof cement paint of approved quality on previously old treated surface with this paint to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powder material including curing and cost of all materials. ch. 15 item no. 19.29 17 finishing walls with one coat of waterproof cement paint of approved quality on previously old treated surface with this paint to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powder material including curing and cost of all materials. ch. 15 item no.662 18 providing & applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. ch. 15 item no. 31-new 19 one priming coat & two coat oil distemper on new work including supply of all materials, labour, t&p etc. required for proper completion of work. paint to be used should confirm isi no. 103-1950. (si. no. 9+10-682) chapter -16 20 painting 1st coat over priming coat (but excluding cost of priming coat) on steel and other metal surfaces upto 10cm width or girth or small articles not exceeding 0.10 sq.m. in area with superior synthetic enamel such as luxol 3, hi gloss apcolite, superlac, dulux specified brushing to give and even shade and including the cleaning the surface of all dirt, dust and other foreign matter sand papering and scrapping including cost of all materials, labour, tools and plants etc. required for proper completion of work.( ch-15 ,2-19.29 +3-642) 21 painting 1st coat over priming coat (but excluding cost of priming coat) on steel and other metal surfaces upto 10cm width or girth or small articles not exceeding 0.10 sq.m. in area with superior synthetic enamel such as luxol 3, hi gloss apcolite, superlac, dulux specified brushing to give and even shade and including the cleaning the surface of all dirt, dust and other foreign matter sand papering and scrapping including cost of all materials, labour, tools and plants etc. required for proper completion of work.( ch-15 si no 3-642 ) 22 providing and fixing water closet squatting pan (indian type w.c. pan) with 100 mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:white vitreous china orissa pattern w.c. pan of size 580x440 mm with integral type foot rests. 23 providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps,32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets,cutting and making good the walls wherever require: white vitreous china wash basin size 630x450 mm with a pair of 15 mm c. p. brass pillar taps 24 supply & fixing of 11 cm (4) internal dia. pvc down pipes complete with rosehead, bends and gratings & including supply of necessary m.s. clamps 2.5cmx 3 mm1x 1/8) fixed to walls, with & includiug supply of 15cm (6) long 6 mm(1/4) dia. nails & including supply of all material labour and t&p etc. required for proper completion of the work & also including repair of plaster,pointing etc. if damaged during fixing of pipes. details of 30 length. toilet waste water 25 note - 1. cost of maintenance of road for five years will be paid as per g.o. no. 17/2024 sa-113/23-1-2024-23-1099/113/2023 date 16-01-2024 2. the departmental road roller if spare, shall be made available to the contructior at site @ rs. 2500 per day shall be made from contractors bell for idle period 3.payment of maintenance shall be made as per final execution of civil work wich may vary from the boq.

State Government

TRN :49029493 | 15 May, 2025

Tender Value : 32.33 Lacs

Gautam Buddha Nagar - Uttar Pradesh

Tender for construction of e-library room in village begmabad yea. wc-06 - earth work in excavation in ordinary soil in all of foundation trenches including dressing of the side and ramming of bottom.lifts up to 1.50 m including getting out theexcavated soil and disposal of surplus excavated soil as directed with in a lead of 50m. (most/a.r./yeida) 2 supplying chemical emulsion in sealed containers including delivery as specified. chlorpyriphos/ lindane emulsifiable concentrate of 20%. (dar/2.34.1/based on uppwd/sor-2020)) 3 diluting and injecting chemical emulsion for post-constructional anti-termite treatment (excluding the cost of chemical emulsion) : treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 coarse sand) to match the existing floor: with chlorpyriphos/lindane e.c. 20% with 1% concentration (dar/2.35.3.1/based on uppwd/sor-2020)) 4 2.5 cm thick damp proof course with cement and approved coarse sand 1:1½ with and including water proofing as ordered by the engineer incharge in the proportion as specified by the manufacturer including supply of all materials, labour, tools & plants etc. required for proper completion of the work and including proper curing & shutterings as necessary. (uppwd/sor-2020/361) 5 applying a coat of residual petroleum bitumen of grade of vg-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. 6 cement concrete with 4cmgauge approved stone ballast, coarse sand & cement in the proportion of 8:4:1 including supply of all material, labour, tools&plants etc required for proper completion of the work. 7 b/w with bricks of class 150 in foundation & plinth in cm 1:4 (based on up pwd sor 2020) cement mortar 1:4 ( 1cement :4coarse sand) 8 m-150 brick work in 1:4 one cement and four course sand 2.20 f.m. mortar superstructure but for walls of half brick thick including supply of all material, labour, t&p etc. required for proper completion of the work. (uppwd/sor-2020/305(a)+310a 9 m-150 brick work in 1:4 one cement and four course sand 2.20 f.m. mortar superstructure but for walls of half brick thick including supply of all material, labour, t&p etc. required for proper completion of the work. (uppwd/sor-2020/305(a)+310a 10 extra for providing and placing in position 2 nos 6mm dia. m.s. bars at every third course of half brick masonry.uppwd-sor-2020-dar-18/6.15/ 11 providing and laying in position machine batched and machine mixed design mix m-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per is: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer-in-charge. (note :- cement content considered in this item is @ 330 kg/cum. excess/ less cement used as per design mix is payable/recoverable separately). all works upto plinth level 12 providing and laying in position machine batched and machine mixed design mix m-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per is: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer-in-charge. (note :- cement content considered in this item is @ 330 kg/cum. excess/ less cement used as per design mix is payable/recoverable separately).all works above plinth level upto floor v level 13 centringand shutteringincluding strutting, propping etc. andremoval of form for : foundation footings, base of column 14 centringand shutteringincluding strutting, propping etc. andremoval of form for : lintels, beams, plinth beam, grinder 15 centringand shutteringincluding strutting, propping etc. andremoval of form for : suspended floors, roofs, landings 16 columns, pillars, piers, abutments, posts and struts. (dar/5.9.6/based on uppwd/sor-2020)) 17 edges of slabs and breaks in floors and walls:under 20 cms wide. (dar/5.9.16.1/based on uppwd/sor-2020)) 18 earth work in rough excavation , banking excavaated earth in layers not exceeding 20 cm in depth, breaking clods watering, rolling each layer with 1/2 tonnes roller or wooden or steel rammer and rolling every 3rd and top most layer with power roller of minimum 8 tonnes and dressing up in embankments for roads, flood banks, marginal banks and guide banks or filling up ground depressions, all leads as per(a.r. )for all kind of soil. 19 steel rainforcement for r.c.c. work including straightening, cutting bending, placing in position and binding all complete upto plinth level thermo-mechanically treated bars of grade fe-500d or more./cold twisted bars. (dar/5.22.6/based on uppwd/sor-2020)) 20 12mm cement plaster of mix: 1:6 (1 cement : 6 coarse sand)based on up pwd sor 2020 dar-18/13.4.2 21 6mm cement plaster of mix: 1:3 (1 cement : 3 coarse sand)based on up pwd sor 2020 dar-18/13.17 22 15mm cement plaster of mix: 1:6 (1 cement : 6 coarse sand)based on up pwd sor 2020 dar-18/13.4.2 23 finishing walls with acrylic smooth exterior paint of required shade: new work (two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm). 24 distempering with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade 25 providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.dar-18/13.26 26 painting with synthetic enemel paint of approved brand and manufacture to give an even shade: two or more coats on new work. 27 providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, (i) single socketed pipes. 110mm dia 28 providing and fixing on wall face unplasticised - pvc moulded fittings/ accessories for unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion. single tee with door 110x110x110 mm (dar/12.42.3.2/based on uppwd/sor-2020) 29 bend 87.5° 110 mm bend (dar/12.42.5.2/based on uppwd/sor-2020) 30 shoe (plain) 110 mm shoe (dar/12.42.6.2/based on uppwd/sor-2020) 31 providing and fixing unplasticised -pvc pipe clips of approved design to unplasticised - pvc rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with m.s. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm (dar/12.43.2/based on uppwd/sor-2020) 32 providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.(dar/12.44/based on uppwd/sor-2020) 33 steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.dar-18/10.25.2 34 providing and fixing water closet squatting pan (indian type w.c. pan with 100mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required white vitreous china orissa pattern w.c. pan of size 580x440mm with integral type foot rests.up pwd sor-2020-dar 18/17.1.1 35 providing and fixing wash basin with c.l. brackets, 15 mm c.p. brass pillar taps,32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required:uppwd sor-2020-dar 17.7.1 36 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge.20mm od pipes. (dar/18.8.2/based on uppwd/sor-2020) 37 25mm od pipes. (dar/18.8.3/based on uppwd/sor-2020) 38 providing and fixingbrass gate valve with c.i. wheel of approved quality (screwed end) : 25 mm nominal bore. (dar/18.17.1/based on uppwd/sor-2020) 39 32 mm nominal bore. (dar/18.17.2/based on uppwd/sor-2020) 40 providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) applying a slurry coat of neat cement using 2.75 kg/sqm. of cement admixed with water proofing compound conforming to is. 2645 and approved by engineer-in-charge over the rcc slab including adjoining walls upto 300mm height including cleaning the surface before treatment. b) laying brick bats with mortar using broken bricks/brick bats 25 mm to 115mm size with 50% of cement mortar 1:5 (1 cement: 5 coarse sand) admixed with water proofing compound conforming to is : 2645 and approved by engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to is : 2645 and approved by engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c) after two days of proper curing applying a second coat of cement slurry using 2.75kg! sqm of cement admixed with water proofing compound conforming to is : 2645 and approved by engineer-in-charge. d) finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement: 4 coarse sand) admixed with water proofing compound conforming to is: 2645 and approved by engineer-in-charge including laying glass fibre doth of approved quality in top layer of plaster and finally finishing the surface with trowe’ with neat cement suvr an making pattern ot 300x300 mm square 3mm deep. e) the whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. all above operations to be done in order and as directed and specified by the engineer-in-charge: dar18/22.7.1 41 providing and placing on terrace (at all floor levels) polyethylene water storage tank isi: 12701 marked with cover and suttable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank dar 18/ 18.48 42 making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - iii) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.(dar 2018-4.17)based on uppwd sor/2020 43 providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. size of tile 600x600mm (dar/11.41.2/based on uppwd/sor-2020)) 44 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer-in-charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (dar/8.31/based on uppwd/sor-2020)) 45 providing and fixing brass bib cock of approved quality: 15 mm nominal bore (dar/18.15.1/based on uppwd/sor-2020)) 46 providing and fixingbrass gate valve with c.i. wheel of approved quality (screwed end) : 25 mm nominal bore. (dar/18.17.1/based on uppwd/sor-2020) 47 providing and fixing nahani trap 75x100mmincluding all complete. 48 20 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand-dar-18/13.6.1/p-902 49 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30mm thick including isi marked stainless steel butt hinges with necessary screws. (dar/9.21.2/based on uppwd/sor-2020)) 50 extra for providing isi marked stainless steel butt hinges instead of m.s. pressed butt hinges bright finished of required size with necessary screws. (shutter area to be measured). (dar/9.14/based on uppwd/sor-2020)) 51 renewing panes of glass in door, window & ventilators or fixing in the new work with 3mm thick glass panes fixed with brads & putty includung supply of all material , labour , tools & plants required for proper completion of workuppwd sor 2020/p26/806 52 prroviding and fixing isi mark 3 layer prelaminated particle board conforming to grade 2 type-iii of is-12823/20b laminated with 0.6-0.8 mm thick laminate conforming to is-2046/1995 and balancing lamination of 0.5 mm thick on the back side (size 700750430) including all complete 53 supply of work sb collection office/visitor chain with sheat dxwxh 400400450 mm padded with polyurithane foam complete 54 supply wook at site sb collection executive table of 3 layer prelaminated particle board (wood product) of grade 2 type 2 of is-12823/latest 1830 mm 950 mm 750mm including all complete 55 supplying and filling in plinth with jamuna sand under floors, including watering, ramming, consolidating and dressing complete. dar-18/2.27 56 providing and fixing factory made isi marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as f7d, f4b, k11 b and k12 b etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment).fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of c.c. 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 57 constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast r.c.c. horizontal grating with frame complete as per standard design with common burnt clay f.p.s. (non modular) bricks of class designation 7.5.(dar/18.33.1/based on uppwd/sor-2020) 58 providing, laying and jointing glazed stoneware pipes class sp-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : (dar/19.1.1/based on uppwd/sor-2020) 59 providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round s.w. pipes including bed concrete as per standard design : (dar/19.2.2/based on uppwd/sor-2020) 60 providing and fixing square-mouth s.w. gully trap class sp-1 complete withc.i. grating brick masonry chamber with water tight c.i. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: (dar/19.4.1/based on uppwd/sor-2020) 61 providing and fixing heavy class ss gratingof approved design including setting in floor with cement motor to match with floor finish as per architect requirement suitable for waster and ft, ut & fd.size 150 mm x 150 mm 62 providing and fixing ptmt towel rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.(dar/17.73.2/based on uppwd/sor-2020)) 63 providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with c.p. brass screws and washers complete. (dar/17.31/based on uppwd/sor-2020)) 64 providing and fixing ptmt soap dish holder having length of 138mm, breadth102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. (dar/18.65/based on uppwd/sor-2020)) 65 providing and fixing chicken wire mesh (murga jali) 24 gauge and 20 mesh at junction of rcc and masonry walls including fixing in position with steel nails of 25 mm in length as approved at required as directed by engineer-in-charge, scaffolding etc. complete. (ar/yeida//based on uppwd/sor-2020))½x24 gauge 66 providing and fixing aluminium hanging floor door stopper, isi marked, anodised (anodic coating not less than grade ac 10 as per is: 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.(dar/9.101.1/based on uppwd/sor-2020))single rubber stopper 67 providing and fixing aluminium tower bolts, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:250x10mm(dar/9.97.2/based on uppwd/sor-2020)) 68 providing and fixing aluminium handles,isi marked, anodised (anodic coating not less than grade ac 10 as per is: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete.125 mm (dar/9.100.1/based on uppwd/sor-2020)) 69 providing and fixing ptmt extension nipple for water tank pipe, fittings of approved quality and colour.25mm nominal bore, weighing not less than 62 gms. (dar/18.75.3/based on uppwd/sor-2020)) 70 providing & fixing of cp heavy duty bottle trap 32mm. (complete complying with relavent standard specification and as directed by the competent authority.) for wash basin&urinal 71 providing and fixing 1 mm thick m.s. sheet sliding-shutters, with frame and diagonal braces of 40x40x6 mm angle iron, 3 mm m.s. gusset plates at the junctions and corners, 25 mm dia pulley, 40x40x6 mm angle and t- iron guide at the top and bottom respectively, including applying a priming coat of approved steel primer up pwd sor-2020-dar-18/10.4 72 construction of granular sub-base by providing close graded material, mixing in mechanical mix plant at omc, carriage of mixed material to work at site, spreading uniform layers with motor grader on prepared surface and compacting with vibratory roller to achieve the desired density, complete as per clause 401 for grade-1 material. (morth/(ar/yeida/based on uppwd/sor-2020) 73 providing and laying 60mm thick i.s.i. mark factory made cement concrete interlocking concrete paver block made by block making machine with strong vibratory compaction of approved size, design, shape, laid in required colour and pattern over and including average 50mm thick compacted bed coarse sand and filling the joints with fine sand all complete as per the direction of engineer-in-charge with conforming to is-15658 and irc:sp:63. (ar/yeida/ based on uppwd/sor-2020) 74 wiring point for light in 1.5 sq. mm. pvcinsulated singlecorecopperconductor cable (inpvcconduit with 1.5sq.mm. frlsh pvc insulated multistrand copperconductor cable as earth wire drawn inside conduit.)and5 amp.flush typeswitch& ceiling rose/angle/batten holderfixedwith3mmthickphenolic laminate backalitesheet withbrass machinescrews andcup washers mounted overexisting m.s.switch boardbox/junction boxwith supplyofallmaterial, labour& t&p etc. requiredforproper completion of the work complete in all respect, as directed by engineer in charge pwd-2018 ps no-174c 75 supply and wiring of submains with 2 nos. of 2.5 sq. mm. frlsh pvc insulated1100 vgrade multistrand singlecore copper conductorcable in 25mm dia heavy duty (2mm thick) pvc conduitwith2 nos 2.5 sq.mm.frlsh pvc insulated multistrand copperconductor cable asearth continuity wire drawn in conduit complete in all respect, as directed by engineer in charge pwd-2018 ps no-261c 76 supply and fixing of power plug with 20 amp./250 voltflush type modularswitchand 5 pin 20 a/250 voltflush typeuniversal modular socket switch on concealed m.sboxincluding supply of allmaterial, labourt&petc. complete in all respect, as directed by engineer in charge .pwd-2018 ps no-1139a 77 s&f surface/flush mounting 8 ways spn distribution board with additional metal door without mcb complete in all respect, as directed by engineer in charge. pwd-2018 ps -1024a 78 s&f of 6 amp to 32 amp. mcb (10 ka) c curve complete in all respect, as directed by engineer in charge.pwd-2018ps -1002cat-a 79 s&f of 40amp. dp mcb (10 ka) c curve complete in all respect, as directed by engineer in charge. pwd-2018 ps no-1010 cat-a 80 providing and fixing circular/ hexagonal cast iron or m.s. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick m.s. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ m.s. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. clamp shall be made of 12 mm dia m.s. bar bent to shape as per standard drawing. (dar/10.18/based on uppwd/sor-2020))

State Government

TRN :49029514 | 16 May, 2025

Tender Value : 54.50 Lacs

Jhansi - Uttar Pradesh

Tender for tender for work of installing tin shed in narsingh bhagwan temple premises in nagar panchayat katera - excavation in soil mixed with moorum/ shingle/ kankar requiring the use of special t&p such as pickaxes, subbals etc.including lift upto 1.5 metre (5 fts.) and lead upto 30 m (100 fts) & including filling, watering and ramming of excavated earth into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the engineer-in-charge upto a distance of 30 m. (100 fts) from the foundation trenches. s.i no - 252.ch.4 2 cement concrete with 4cmgauge approved stone ballast, approved coarse sand, cement in the proportion 8:4:1 including supply of all materials, labour and tools and plants etc. required for proper completion of the work.pcc si no.281.ch-5. 3 r.c.c work with cement approved coarse sand and 2 cm. (3/4) gauge approved stone ballast in the proportion of 1:1.5:3 in footing excluding supply of reinforcement and its binding wire and including its fixing and binding the same with 24 b w.g.g.i. binding wire an including neccecary centering & shuttering etc & also including supply of all materials labour & t&p etc required for proper completion of the work. binding wire cost being included in the item 287 -1st.ch-5. 4 rcc work with cement approved coarse sand, and 2cm (3/4) gauge, approved stone ballast in the proportion 1:1.5:3 in column, excluding supply of reinforcement and its bending but including its fixing and binding the same with 24 b.w.g.i. binding wire, an including necessary cantering and shuttering etc and also including supply of all materials, labour and tools and plants etc. required for proper completion of the work binding wire to be supplied by the contractor free of cost.si no.288-1st.ch-5. 5 brick work with non modular fly ash lime bricks (falg bricks) conforming to is:12894, class designation 10 average compressive strength in foundation cement mortar 1:6 (1 cement : 6 coarse sand) as per sor s.i. no. dsr 6.34.ch-6. 6 r.c.c work with cement approved coarse sand and 2 cm. (3/4) gauge approved stone ballast in the proportion of 1:1.5:3 in plinth beam/lighter beam excluding supply of reinforcement and its binding wire and including its fixing and binding the same with 24 b w.g.g.i. binding wire an including neccecary centering & shuttering etc & also including supply of all materials labour & t&p etc required for proper completion of the work. binding wire cost being included in the item no-285 1st.ch-5. 7 brick work with non modular fly ash lime bricks (falg bricks) conforming to is:12894, class designation 10 average compressive strength in super structure cement mortar 1:4 (1 cement : 4 coarse sand) as per sor s.i. no. dsr 6.34.ch-6. 8 earth work in cutting or in filling in ordinary soil, excavation to be in the form of regular pits not exceeding 1/2 metre (20) in depth and earthwork in embankment to be in 20 cm(8) layers, including ramming & dressing the surface to required levels and slopes and also including 1.5 metre (5fts) lifts and 30 m. (100) lead. the earth from cutting to be used in making filling or to be deposited as spoil banks within 30 metres (100 fts) distance as directed by engineer-in-charge. s.i. no.253.ch-4. 9 mild steel or iron work in plain work such as reinforced concrete/brick work (when not included in over all rates) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel, its wastage and hooks, and authorized over lapping shall be measured.si. no. 504 10 15 mm thick plaster on rough side brick work minimum thickness not less than 10 mm with cement mortar in proportion of 1:6 cement and fine sand of 1.25 fineness modulus including supply of all materials, labour and tools and plants etc required for proper completion of the work.si no.17.59(3) 11 providing and applying plaster of paris putty of 2 mm thickness over plasterod surfaco to prepare the surface even and smooth complete. s.i. no. new item ref. dar-13.26. ch.-15. 12 finishing walls with water proof cement paint of approved makeand quality on new work with three coats to give an even shade including supply of all materials labour, tools and plants etc. required for proper completion of work.si no.660+661 13 kota stone slab 20 mm thick in kitchen slab over 20 mm thick base of 1:4 cement morter laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab s.i no 14.43 (a), ch-14. 14 for teen shed and godown-

corporations/Associations/Others

TRN :34414767 | 12 May, 2025

Tender Value : 0

Angul - Orissa

Tender for gem bids for safety fire extinguishers , essentialssupply and , p and f of first aid k , p and f of different d , sitc of bullet camera 2mp 1920 x 1080 pixel , p and f of cabin naming in vinyl on glass , supply and installtion of pull push signages , stainless steel plai , showpiece idol offic , desktop vase , room vase large , poster with mdf frame , corner wall shelf , supply and installtion of leather desk matt , supply and installtion of floor carpet , dismantling , brick masonary , dism plaster , providing 12 mm cement plaster , spl plaster of paris , wall paint , electrical , dism tiles granite , sandf vitrified tiles size 600x600 10 , dism false ceilling , ceilling , light fittings in false ceiling , dismantling door window , windows , door , conference table 18 seater 6m x 1.8m , chairs , p and f of glass board 3 ft x 4 ft size , p and f of noctice boa , oandm of projector system , 86 inch interactive display panels , p and f of sound system , wood work , podium , supply and installation of a modern credenza system , suply and installation of apollo corner sofa , showcase storage wall mount shelve large , showcase storage wall mount shelve small , coat stand , supply and placement of low maintenance indoor plants , sitc of desk monitor , storage , showcase storage wall mount shelve , manager table , installation of pop up switch box , workstation construction materials and tools , supply and installation of multipurpose printer machine , frp door , ms steel racks , ladder for steel rack , supply and placement , essentials , bldg masonry . half bk with stfr , granite for sink plateform , sanitary . hd pvc pipe 50mm , sanitary . hd pvc pipe 75mm , sanitary . hd pvc pipe 100mm , sanitary . upvc pipes 90mm 4 kg sqcm , sanitary . upvc pipes 160mm 4 kg sqcm , sanitary . upvc pipes 250mm 4 kg sqcm , urinal , urinal s f of sensor valves for urinals. , urinal seprator , wc , sanitary . sintex tanks 1000 ltrs. capac , door win . . floor spring , door win . . brass handle , door win . . godrej mortice lock , door win . . hyd door closer , terrace tile , sf ss 304 grade rail , apply vetrified glossy ceramic tiles for flooring , alcohol detector , hvac , hvac service , brick masonary for security room , frp shed for security room , door win . blinds sun film , door win collapsible shutter

Central Government/Public Sector

TRN :34415845 | 13 May, 2025

Tender Value : 0

Nasikcity - Maharashtra

Tender for gem bids for 5000 plaster of paris gypsum made is-2547

corporations/Associations/Others

TRN :34405402 | 08 May, 2025

Tender Value : 0

Pune - Maharashtra

Tender for gem bids for single use rubber examination gloves (v2) (q2) , disposable surgical rubber gloves (v2) (q2) , absorbent cotton wool (v2) (q2) , absorbent cotton gauze (q2) , surgical apron (q2) , zinc oxide elastic self - adhesive bandage (v2) (q2) , plaster of paris bandage (v2) (q2) , disposable bed sheets for health care facility (q3) , elastic surgical adhesive tapes (v2) (q2)

Central Government / Public Sector

TRN :34392889 | 08 May, 2025

Tender Value : 0

Pune - Maharashtra

Tender for gem bids for pva bag 10 inch 10 piece pi pva b 10 inch , bandage of plaster of paris , film pvc width 122 cm , tape self adhesive pvc 125mm 3 oblique 4 inch cello red heavy duty polypropylene pressure sensitive adhesive tapes , thread sewing polyster black no 30 1000 mtrs , stump socks symes 26 inch , plaster of paris pop pdr oblique unbranded class iii plaster dental stone size 25 kilogram in bag , light weight non leather antiskid rubber sole and oil resistant single density sole low ankle with netted body and isi grade certified shoes size 7 , liquid adhesive general purpose dunlop

Central Government / Public Sector

TRN :34393102 | 08 May, 2025

Tender Value : 0

Pune - Maharashtra

Tender for gem bids for 1877 film pvc width 122 cm synthetic rubber sheet 3 inch x 2 inch x 1 oblique 8 3mm multicolor plaster of paris pop pdr oblique unbranded class iii plaster dental stone size 25 kilogram in bag stockinette cotton 6 point 5 cm oblique 2 inch leather softy brown light

Related Searched Keywords : plaster of paris

List of plaster-of-paris Tenders

Tender for gem bids for 5000 plaster of paris gypsum made is-2547

Tender for gem bids for 1877 film pvc width 122 cm synthetic rubber sheet 3 inch x 2 inch x 1 oblique 8 3mm multicolor plaster of paris pop pdr oblique unbranded class iii plaster dental stone size 25 kilogram in bag stockinette cotton 6 point 5 cm oblique 2 inch leather softy brown light

Get plaster of paris Tender Alert...

Related Searched Keywords : plaster of paris

State Tenders »

City Tenders »

Keyword Tenders »

Sector Tenders »

Ownership Tenders »

Indian Segment

Browse Tenders

Global Segment

Others

Get in touch with us